User's Manual: Astronaut Projector Lamp

Attention

The light source of stars and nebulae is strong; eyes should not look directly at the light source.

The brightness of the stars (i.e., laser brightness) is affected by the ambient temperature and time of use. When the ambient temperature is hot or the power-on time is longer, the brightness of the laser will decrease due to the heat of the light source. At this time, turn off the power and let the laser cool down. The heat dissipation of the device usually takes more than 15 minutes. Then turn it on to restore the brightness.

The head and body of the astronaut are connected together by magnets, and the direction of the head can be adjusted. Do not stretch the astronaut's head and body forcefully, otherwise the wires may break due to stretching.

Image description: A stylized astronaut figure is shown. Text below the image provides instructions: "Please install the base before using. Please make sure that the astronaut's feet are in full contact with the bottom of the base seat." Another image shows the rear view of the astronaut, with text stating: "The projection direction can be adjusted by adjusting the rotation angle of the astronaut's head."

Host Key Operation Instructions

Diagram description: A control panel is depicted with the following labels: Power switch, Nebula Switch, Star switch, Timing indicator, and Power jack.

• [Power Switch]: Short press the power switch to turn on the device. The stars and mixed-color nebula are turned on by default.
• [Nebula Switch]: Short press to switch the color of the nebula. Long press to turn off the nebula function; short press again to turn it back on.
• [Star Switch]: Short press to switch the star's breathing rate. Long press to turn off the star function; short press again to turn it back on.
• [Timing Indicator]: This light illuminates after pressing any timing button on the remote control and turns off when the timing function is deactivated.

Remote Control Instructions

Diagram description: A remote control is shown with various buttons. The buttons are labeled or implied by function: [Button U] (Power/Switch), [Button ⭐] (Star Switch), [Button ?] (Nebula Color Switching), [Button B+] (Nebula Brightness +), [Button B-] (Nebula Brightness -), [Button S+] (Star Breathing Rate +), [Button S-] (Star Breathing Rate -), [Button G+] (Nebula Change Speed +), [Button G-] (Nebula Change Speed -), [Button Timer] (Timing Button).

• [Button U] (Switch): Short press to turn on the device. Nebula and Stars are turned on by default. Short press again after turning on to turn off.
• [Button Timer] (Timing Button): The timing function has two levels: 45 minutes and 90 minutes. Pressing once activates 45-minute timing (blue indicator light). Pressing a second time activates 90-minute timing (red indicator light). The indicator light remains on during timing. Long press cancels the timer, and the indicator light turns off.
• [Button B+] (Nebula Brightness +): Adjusts Nebula brightness through 5 levels. Each press increases brightness by one level.
• [Button ?] (Nebula Color Switching): Each press cycles through nebula colors. Long press turns off the nebula; short press turns it back on.
• [Button G-] (Nebula Change Speed -): Adjusts Nebula change speed across 5 gears (0 is static, 4 is fastest). Each press decreases the speed by one level.
• [Button G+] (Nebula Change Speed +): Increases Nebula change speed by one level with each press, up to level 3.
• [Button B-] (Nebula Brightness -): Decreases Nebula brightness through 5 levels.
• [Button Star Switch]: Long press to turn off the star function. Short press to turn the star function back on.
• [Button S-] (Star Breathing Rate -): Adjusts star breathing rate across 4 gears (0 means stars are always on, 3 is the highest frequency). Each press reduces the rate by one gear.
• [Button S+] (Star Breathing Rate +): Increases star breathing rate by one level, up to level 3.
• [Button Star Brightness -]: Adjusts star brightness (only in normally bright mode, invalid in breathing state). There are three levels. Each press reduces brightness by one level.
• [Button Star Brightness +]: Increases star brightness by one level until the brightest gear is reached.

Technical Specifications

• Material: ABS/PC/PVC
• Product Color: White
• Laser Wavelength: 532nm
• LED Power: < 5W
• Control Mode: Remote control
• Remote Control Range: < 5 meters (Best distance)
• Power Supply: 100-240V~50/60Hz 0.4A
• Work Input: 5V-1A
• Product Size: 120*113*228mm
• Applicable Environment: Indoor Home (Better in a dark environment)
• Working Temperature: -10°~45°Celsius

Certifications: FDA, FC, CE, ROHS