DAISO_BT007,8 Bluetooth Earphone User Manual

Important Safety Precautions

Please read the following precautions carefully before use. Failure to adhere to these warnings and precautions may result in injury, disability, death, or property damage. Do not use the product for unintended purposes or in ways not described herein. Illustrations are for representational purposes only.

• Never use while cycling, driving a car or motorcycle, as this can cause traffic accidents. Avoid use in locations where hearing your surroundings is crucial for safety, such as train crossings, platforms, roadways, or construction sites.
• Noise or audio interruptions may occur due to the connected Bluetooth device, communication environment, or surrounding conditions (crowded places, train stations, areas with many communication devices).
• Prolonged use at high volumes that stimulate the ears can significantly damage hearing.
• Avoid sudden loud sounds by gradually increasing the volume.
• Be cautious not to set the incoming call volume too high.
• Discontinue use immediately if the product becomes deformed or damaged.
• Stop use immediately if skin irritation occurs upon contact.
• Do not disassemble or modify the product.
• Do not drop or subject the product to excessive impact.
• The product is not water-resistant. Avoid contact with water and do not operate with wet hands.
• Do not expose to thinner, benzene, or alcohol.
• Do not charge with a current exceeding 5V/1A. Avoid using high-speed charging adapters.
• Do not leave the product connected after charging is complete.
• For safety, when charging with a car charger, connect the charging cable to the product's charging port only after starting the car engine.
• Avoid using or storing the product in places with strong magnetic fields, static electricity, electrical noise, condensation, risk of short circuits or water leaks, high temperature/humidity, direct sunlight, near fire or heat sources, or in dusty environments.
• Do not cover the product with blankets, pillows, or bedding during use.
• Keep away from fire and heat sources.
• Children should be supervised by a guardian during use.
• Do not dispose of with regular household waste.
• This product is intended for use only in countries where it complies with or is certified to radio laws. It cannot be used outside the country of sale.
• The product operates in the 2.4GHz band. Interference may occur from other devices using the same frequency band (Bluetooth devices, Wi-Fi, cordless phones, microwaves).
• Do not use in areas where radio waves are prohibited, such as hospitals, as it may affect medical devices like pacemakers.
• Consult your airline regarding the use of wireless devices on board aircraft.
• Follow the instructions in the connected device's manual before use.
• While the product can connect wirelessly to mobile phones and computers, setup methods and precautions vary by device.
• Batteries are consumable parts that degrade with normal use. Battery depletion is a characteristic and not a malfunction. Batteries cannot be replaced.

Note: Charging cable not included. Please provide your own USB Type-C charging cable.

Charging

If the LED blinks red, the battery is low. Connect a charging cable to the USB Type-C port to charge. The LED will light red during charging and turn off when fully charged.

Note: For prolonged periods of non-use, charge the battery every few months to prevent deterioration due to self-discharge.

Using the Remote Control

The remote control is designed to be positioned on the right side when wearing the earphones.

Note: Usable functions may vary depending on the connected device and app. If communication is interrupted, the earphones enter power save mode and will automatically turn off after a few minutes if no reconnection occurs.

Pairing and Connecting the Earphones

Initial Device Registration:

1. With the power off, press and hold the Multi Function Button for over 3 seconds to enter pairing mode. The LED will blink red and blue alternately.
2. On the Bluetooth settings of the connecting device, search for and select the model number starting with “DAISO_BT0~~” to complete pairing. The LED will blink blue upon successful pairing.

Notes:

• Model numbers may vary by product.
• Once paired, the earphones will automatically connect on subsequent uses.
• To pair with a different device, disconnect Bluetooth from the current device and repeat steps 1 and 2.
• Ensure Bluetooth is enabled on the connecting device.
• Verify that the connecting device supports the product's Bluetooth profile.
• If pairing fails, delete the earphones' registration information from the connecting device's Bluetooth settings and try pairing again.
• Pairing may be unsuccessful if strong electromagnetic waves are present. Move away from other electronic devices or turn off their power before attempting to pair again.
• Resetting the Earphones: If pairing continues to fail, reset the earphones by pressing and holding the “Next Button” and “Previous Button” simultaneously for approximately 5 seconds while the power is ON. Then, delete the earphones' Bluetooth registration information from the connecting device, turn the product power ON again, and pair. (Note: Resetting will delete connected device information.)

Multipoint Connection Setup

Multipoint allows the earphones to be ready for use with two smartphones simultaneously.

1. Pair the product with the first smartphone.
2. Turn off Bluetooth on the first smartphone.
3. Pair the product with the second smartphone.
4. Turn on Bluetooth on the first smartphone.
5. From the first smartphone's Bluetooth settings, select the registered model number of this product to pair.
6. The product will now support simultaneous standby with both smartphones (Multipoint).

Note: This feature is exclusive to two smartphones. It is not compatible with computers or game consoles. Compatibility is not guaranteed with all Bluetooth-compatible smartphones and mobile phone combinations.

Troubleshooting Pairing Issues

• Ensure the connecting device's Bluetooth function is enabled.
• Confirm the connecting device supports this product's profile.
• Delete the product's registration from the connecting device's Bluetooth settings and re-pair.
• Move away from or turn off other electronic devices that may cause electromagnetic interference.
• If issues persist, reset the earphones as described in the pairing section.

How to Clean

Wipe clean with a soft cloth.

FCC Compliance Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Industry Canada Compliance Information

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.