mailto:service@joy-it.net
Joy-IT Helpdesk
For Makers and Professionals | Joy-IT
dl.espressif.com/dl/package_esp32_index.json
Instruction Manual for joy-it models including: ESP32 Camera Module, ESP32, Camera Module, Module
Sep 15, 2023 — GENERAL INFORMATION. Dear customer, thank you very much for choosing our product. In following, we will introduce you to what to observe while starting up.
www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn Now you can select under Tools -> Board -> ESP 32 Arduino, the board AI Thinker ESP32-CAM. You can now start programming your module.
File Info : application/pdf, 8 Pages, 1.09MB
DocumentDocumentESP32 CAMERA MODULE SBC-ESP32-Cam 1. GENERAL INFORMATION Dear customer, thank you very much for choosing our product. In following, we will introduce you to what to observe while starting up and using this product. Should you encounter any unexpected problems during use, please do not hesitate to contact us. www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn 2. PINOUT 5V 3,3V GND IO16 IO12 IO0 IO13 GND IO15 VCC IO14 IO3 / U0R IO2 IO1 / U0T IO4 GND LED (IO4) The following pins are internally connected to the SD card slot: · IO14: CLK · IO15: CMD · IO2: Data 0 · IO4: Data 1 (also connected to the on-board LED) · IO12: Data 2 · IO13: Data 3 To put the device into flash mode, IO0 must be connected to GND. www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn 2. SETTING UP THE DEVELOPMENT ENVIRONMENT You can program the camera module using the Arduino IDE. If you do not have the IDE installed on your computer, you can download it here. After you have installed the development environment, you can open it to prepare you for using the camera module. Go to zu File -> Preferences Add the URL: https://dl.espressif.com/dl/package_esp32_index.json under Additional Board Manager URLs. Multiple URLs can be separated with a comma. www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn Now go to Tools -> Board -> Boards Manager... Enter esp32 in the search bar and install the ESP32 board manager www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn Now you can select under Tools -> Board -> ESP 32 Arduino, the board AI Thinker ESP32-CAM. You can now start programming your module. As the module does not have a USB port, you will have to use a USB to TTL converter. For example the SBC-TTL interface converter from Joy-it. When using it, you must make sure that the jumper is in position 3V3. You must use the following pin assignment. Camera module 5V GND U0T U0R Interface converter 5V GND RX TX You also need to connect a ground pin of your camera module to the IO0 pin to upload your programme. You have to remove this connection when the upload is finished. When uploading, you have to restart your camera module once with the reset button as soon as "Connecting......." appears in the debug window below. www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn 2. EXAMPLE PROGRAM CAMERAWEBSERVER To open the sample program CameraWebServer click on File -> Examples -> ESP32 -> Camera -> CameraWebServer Now you must first select the correct camera module (CAMERA_MODEL_AI_THINKER) and comment the other modules with //, as shown in the picture below. You also need to enter the SSID and password of your WiFi network. When this step is also done, you can upload the programme to your camera module. www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn In the serial monitor, if you have set the correct baud rate of 115200, you can see the IP address of your web server. You must enter the displayed IP address in your Internet browser to access the web server. www.joy-it.net Pascalstr. 8 47506 Neukirchen-Vluyn 4. ADDITIONAL INFORMATION Our information and take-back obligations according to PR the Electrical and Electronic Equipment Act (ElektroG) Symbol on electrical and electronic equipment: Tdhoins octrobsesleodn-goiunt dustbin means that electrical and electronic appliances the household waste. You must return the old appliances to a collection point. Before handing over waste batteries and accumulators that are not en- closed by waste equipment must be separated from it. RAsetaunrennodputsioenr,sy:ou can return your old device (which essentially fulfils the same function as the new device purchased from us) free of charge for disposal when you purchase a new device. Small appliances with no external dimensions greater than 25 cm can be disposed of in normal household quantities independently of the purchase of a new appliance. PSIoMsAsiCbEillietyctorof nreictsuGrnmabtHo, uPracscoamlsptra.n8y, ny Dlo-c4a7t5i0o6nNdeuurkinirgchoepne-nVilnuygnh,oGuerrsm: a- PWoeswsiibllislietnydoyf oreutaurpnaricneylostuarmaprewai:th which you can return the device to us free of charge. telephone. Please contact us by email at Service@joy-it.net or by IIfnyfoourmdaotnioont hoanvpeascukitaagbilnegp:ackaging material or do not wish to use your own, please contact us and we will send you suitable packaging. 5. SUPPORT If there are still any issues pending or problems arising after your purchase, we will support you by e-mail, telephone and with our ticket support system. Email: service@joy-it.net Ticket system: http://support.joy-it.net Telephone: +49 (0)2845 98469-66 (Mon - Thur: 10:00 - 17:00 o`clock, Fri: 10:00 - 14:30 o`clock) For further information please visit our website: www.joy-it.net Published: 15.09.2023 SIMAwwCwwEwlwe.c.jjtooryoy--niittic..nnseeGttmbH PaPsacsaclasltsrt.r.884, 477550066NNeukirchheenn--VVluluyynn