Instruction Manual for HPRT models including: HN3358SR, 2AUTE-HN3358SR, 2AUTEHN3358SR, HN-3358SR Handheld Barcode Scanner, HN-3358SR Handheld Barcode Scanner, Barcode Scanner, Scanner
Xiamen Hanin Electronic Technology Co.,Ltd. HN3358SR Handheld Barcode Scanner with BT 2AUTE-HN3358SR 2AUTEHN3358SR hn3358sr
Handheld Barcode Scanner HN-3358SR
Instruction Manual
Appearance
Sound Hole Indicator
Scan Window Type-C
Scan Buon Shutdown Hole
Power on/off and Restart
Start up: 1. Automacally start up aer connecng USB; 2. When USB is not connected, press the scanning buon to start
the scanner. Shut down: 1. Press and hold for 15s to shut down; 2. Shut down automacally aer 15 minutes of silence (without any
touch). Restart: If the scanner crashes or does not response, press the boom switch with the paper clip. Then press the scanning buon to restart.
Maintenance
The reading window must be kept clean.
Avoid hard and rough objects to scratch the reading window. Remove the stains from window with a brush. Please use a so cloth to clean the window, such as glasses cloth. Do not spray any liquid on the window Do not use any cleanner other than cleaning water.
Bluetooth Connection
The scanner is shut up by pressing the scanning buon, and be connected it to the host devices through Bluetooth. The green light indicates that it is connected and can be used normally.
USB Connection
1) Connect the device interface (type-C interface) of USB to scanner; 2) Connect the host interface (USB interface) of USB to the host and
switch to the keyboard mode.
Buzzer
Status Power on Scan Successfully
Beeping mes 3 mes 1
Interface Setting
The scanner can communicate with the host by RS-232 serial port or USB port. The user can switch to the corresponding interface by replacing the cable and scanning the corresponding barcode below.
c1USB virtual keyboard
LED Indicator
Color
Red light on Red light off Red light flash Green light slow flash Green light on Alternang slow flashing
of red and yellow light Yellow light on
Description
Charging Full charge Low power prompt Bluetooth not connected Bluetooth connected Charging and Bluetooth not
connected Charging and Bluetooth
connected
c2USB virtual Serial Port c3Bluetooth
Bluetooth Connection
(1) Set shut down/up me
Disable
5min
10min
15min
30min
60min
Bluetooth Connection
2Pop up iPhone keyboard by Bluetooth
Yes
No
Set Deafults
Scan the barcode to restore all sengs to the factory default state
Note: Please use the "factory reset" funcon carefully. Aer recognizing this barcode, the current parameter sengs will be lost and replaced with the factory default values.
Scanning Mode
Scan mode sengs by scanning the barcode below
c1Manual Mode
c2Sensing Mode
c3connuous Mode
Other
c1Aiming Barcode ON
c2Read Successfully Barcode ON
OFF
OFF
Common Problem
QThere are some barcodes can not be scan. A a) Firstly, check the barcode type and enable the barcode funcon; if
there is verified, try to close the verificaon. b) Unable to know the barcode type, then set all barcodes allow to
be read.
QThe barcode data is incorrect. A
Check the status of barcode errors (whether all barcodes have errors or specific barcodes have errors)
QBar code can be read but not displayed. A
First, confirm whether the working mode of the scanner is in Bluetooth transmission mode; if it is already in Bluetooth transmission mode, confirm whether the Bluetooth of the scanner is connected to the host terminal.
Q Aiming light and illumuniaon light are not on. A a) Check whether the device is powered on. b) Re-plug the data cable.
State
Our company does not assume any responsibility for losses caused by natural disasters (such as earthquakes, floods, etc.) that exceed our scope of responsibility.
In any case, our company does not assume any responsibility for losses caused by using this product, such as loss of profits, loss of reputaon, business interrupon, loss or change of stored data, and any special, unexpected, associated or intermient losses caused by the above.
Our company does not assume the responsibility for the losses caused by due to improper use of hardware or soware not specified by the our company .
Our company does not provide any form of warranty or technical support for the informaon, data, files, other products, services obtained though the use of this product, and does not assume any responsibility for the use of above descripon by users.
Our company are not take any form of guarantee for third-party soware used by this product.
Due to the connuous improvement of the products, the operaon and common problems of the models described in the manual are mainly based on actual machines. And it may be changed without noce.
FCC Warning
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including int-
erference that may cause undesired operaon.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separaon between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help.
FCC Warning
Warning: Changes or modificaons to this unit not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment.
FCC Radiaon Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condion without restricon. FCC ID 2AUTE-HN3358SR
Adobe PDF library 15.00 Adobe Illustrator(R) 17.0