GAMEMAX STORM 2
USER MANUAL / BENUTZERHANDBUCH / MANUAL DO USUÁRIO / РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ / 用户手册
Package Content
| Item | Image | Quantity | Used For |
|---|---|---|---|
| A | [Image: Screws for Motherboard and 2.5" SSD] | 12 | Screws-MB+2.5" SSD / Schrauben-MB+2,5" SSD / Parafusos-MB+2,5" SSD / Винты-МБ+2,5" SSD / 螺丝-MB+2.5" SSD |
| B | [Image: PSU Screw] | 6 | PSU Screw / Stromversorgungsschraube / Parafuso de fonte de alimentação / Винт питания / 电源螺丝 |
| C | [Image: 3.5" HDD Screw] | 4 | 3.5" HDD Screws / 3,5" HDD-Schrauben / Parafusos do HDD de 3,5 pol. / Винты для жесткого диска 3,5" / 3.5" HDD硬盘螺丝 |
| D | [Image: Spare Standoff] | 2 | Spare Standoff / Ersatz -Standoff / Stoff de reposição / Запасное противостояние / 备用铁柱 |
| E | [Image: Cable Tie] | 4 | Cable Tie / Kabelbinder / Abraçadeira / Кабельная стяжка / 束线带 |
Connectors
Connector Types
- Combo Audio:
Pins: PORT 1L (AUG GND), PORT 1R (PRESENCE), PORT 2R (SENSE1_R), SENSE (S), PORT 2L (SENSE2_R).
- POWER SW:
Pins: POWER SW.
- USB3.0:
Pins: VBUS, SSRX1-, SSRX1+, SSRX2-, GND, SSTX1-, SSTX1+, SSTX2+, D1-, D1+, D2-, D2+, NC.
- USB2.0:
Pins: VCC, D-, D+, GND.
I/O Panel
The I/O panel features the following connections:
- Power SW ?
- Type-C ?
- USB 2.0 ?
- LED SW ?
- USB 3.0 ?
- Combo Audio ?
- P-Lock ?
Exploded View
The following components are part of the case structure:
- 1. Front Panel: Frontblende / Painel frontal / Передняя панель / 面板
- 2. Tempered glass left side panel: Linker Schaltplatte mit geschmiedeten Glas / Painel lateral esquerdo de vidro temperado / Панель левой боковой панели / 钢化玻璃左侧板
- 3. Right side panel: Rechte Seite / Painel lateral direito / Правая панель / 右侧板
- 4. Chassis: Chassis / Chassis / Шасси / 机架
- 5. HDD bracket: HDD -Klammer / Suporte de HDD / Жесткий кронштейн / HDD硬盘架
- 6. Magnetic dust filter on top: Magnetstaubfilter oben / Filtro de poeira magnética por cima / Магнитный пыли фильтр сверху / 顶部磁吸式防尘网
- 7. Dust filter at the bottom: Staubfilter unten / Filtro de poeira na parte inferior / Пылевой фильтр внизу / 底部防尘网
- 8. Front Fan x3 (included): Front -Lüfter x3(enthalten) / Fã da frente x3(incluído) / Фронт вентилятор х3 (включен) / 前板风扇x3(标配)
- 9. Top Fan x2 (included): Top -Lüfter x2(enthalten) / Top Fan x2(incluído) / Верхний вентилятор x2 (включен) / 顶板风扇x2(标配)
- 10. Rear fan x1 (included): Heck-Lüfter x1(enthalten) / Ventilador traseiro x1(incluído) / Задний вентилятор х1 (включен) / 后板风扇 x1(标配)
- 11. PSU cover fan x2 (optional): PSU Cover Fan x2(optional) / PSU Cover Fan x2(opcional) / Вентилятор PSU Cover x2 (необязательный) / 电源架风扇 x2(选配)
Installation Guide
- Step 1: Remove Side Panels and Bottom Plate
Remove the left and right side panels and the bottom plate.
- Step 2: Remove Front Panel
Remove the front panel. Note: If the fan has been pre-installed in front, no need to remove the panel.
- Step 3: Install PSU
Insert the PSU from the right side and secure it with screws.
- Step 4: Install Motherboard
Install the motherboard.
- Step 5: Install Graphics Card (PCI-E)
Remove the PCI-E interface card, insert it into the graphics card slot, and lock the screw fixation.
- Step 6: Install 2.5" SSD and 3.5" HDD
Install 2.5" SSD and 3.5" HDD. Multiple configurations are supported (e.g., Option 1: 3.5" HDD, Option 2: 2.5" SSDs, Option 3: 2.5" SSD and 3.5" HDD).
- Step 7: Install 3.5" HDD
Install 3.5" HDD into the designated bays.
- Step 8: Install 2.5" SSD
Install 2.5" SSD into the designated bays.
Cooling System Support
Fan Cooling System
- Front: 120mm x3 (included)
- Top: 120mm x2 (included) or 140mm x2 (optional)
- Rear: 120mm x1 (included)
- PSU Cover: 120mm x2 (optional)
Liquid Cooling System
- Front: Supports 120/140/240/280/360mm radiators
- Top: Supports 240mm radiators (ensure RAM height is ≤ 30mm)
- Rear: Supports 120mm radiators
ARGB Fan Connection Instruction
This section details how to connect ARGB fans.
Fan Models
- Subordinate Fan: Model FN12A-S6
- Master Fan: Model FN12A-M6 (Features built-in ARGB HUB Function)
Connection Details
- Connect fans to SATA power from the PSU.
- Connect to the 5V 3Pin ARGB Header on the motherboard or controller.
- LED Mode: Long press the button for 5 seconds to enter the extended connection mode.
Extending Connections
Two methods are provided for extending ARGB connections:
- Method 1: Link to ADD_Header on Motherboard.
- Method 2: Link to available 5V 3Pin M/F ARGB accessories (such as Liquid Coolers or additional Fans).
