User Manual for SPARK MINDA models including: 360001E, 2A29L-360001E, 2A29L360001E, Electronc Kit, Smart Keyless System
Minda Corporation Limited 360001E 2A29L-360001E 2A29L360001E 360001e
File Info : application/pdf, 12 Pages, 1.06MB
DocumentDocumentSMART KEY SYSTEM'S ( Electronic Kit Keyless System ) MANUAL Introduction Smart Key System employs sophisticated technology provide convenience and peace of mind, coupled with maximum protection, and reliability to your vehicle. The system incorporates two major components; control unit and key FOB. A microprocessor controlled, solid unit connected with in the vehicle. LOCK / UNLOCK operation of the steering lock, fuel cap and seat opener and engine authorization, In addition it has a vehicle locater finder function development with necessary changes corresponding to the requirements of the particular vehicle model. It is proposed to develop a system CONTROL UNIT suitable for two wheelers for the smart key system. Features 1. IGN (Ignition) ON (Engine Start) from the unlocking operation of handle lock Output engine start permission to Engine ECU by IGN ON. In case of detecting the FOB at communication range when PUSH SW of knob is detected. 2. The locking operation of the handle lock from IGN OFF. 3. The locking operation of the handle lock from KNOB SW Press. 4. Detect and notify when the FOB dropped. 5. Detect and notify when the FOB dropped after 50M. 6. Notice of FOB battery voltage reduction. 7. Vehicle Finder. 8. Vehicle Seat function by Key FOB. 9. Vehicle Seat function by seat switch. 10. Vehicle FT Cap function by Key FOB. 11. Vehicle FT Cap function by FT Cap switch. 12. IGN ON at the emergency (In passive mode). System Diagram UHF LF KEY FOB IP67 level sealing of FOB FOB sensing distance of 1.5±0.3m Layered Architecture with Modular HW and Software development Answerback function Seat and FT cap opening UHF LF SMART IGNITION SWITCH Knob operated function no key required Solenoid based system to lock & unlock steering User authorization (smart key) check by Electronic control unit Micro-switch based wake-up of Smart ignition switch FCC ID: 2A29L-365001A IC : 23641-365001A SUPERVISORY CONTROL UNIT IP67 protection level for SCU Layered Architecture with Modular HW and Software development Withstand automotive harsh environment Ultra low quiescent current KEY FOB drop indication FCC ID: 2A29L-360001E IC : 23641-360001E SCU MOUNTING: Select a mounting location behind the dash, and secure using cable ties and bracket. Be certain that the chosen location will not interfere with the proper operation of the vehicle. Avoid mounting the module to or routing the wiring around the steering column, as the module or wiring could wrap around or block the steering wheel preventing proper control of the vehicle. Specification - SUPERVISORY CONTROL UNIT Model No. Rated Voltage Rated Current Operating Current During Ignition ON Condition Operating Temperature IP Rating Protection Short Circuit Protection Over Voltage Protection in Vehicle Operating Frequency : EC-360001E : 12VDC : 5.5A : Less than 750mA : -30°C - +80°C : IP67 : Yes : Yes : Yes (Fuse Provided) : 315MHz (UHF) : 125KHz (LF) Note: SCU mounting at vehicle is rusticated, user can not access the SCU. Specification - KEY FOB Model No. Key FOB Type Rated Voltage Battery Type Recommended Make Operating Temperature Operating Frequency Battery Life IP Rating Symbol Description : ER-365001A : Radio Frequency : 3VDC : Lithium (#CR2032) : Panasonic : -20°C - +55°C : 315MHz (UHF) : 125KHz (LF) : 1 Year (Typical) : IP67 : Vehicle Finder FT Cap function Seat function Specification - Sticker Caution Marking : KEY FOB product consists of Coin battery and product is accessible to children due to that product shall consists of caution symbol. FCC ID: 2A29L-365001A IC : 23641-365001A FCC ID:2A29L-360001E IC : 23641-360001E Specification - FCC Regulatory Information FCC Regulatory Information ( FCC ID is 2A29L-360001E ) : This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received including interference that may cause undesired operation of this device. Any changes or modifications not expressly approved by the party responsible for Compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and , if not Specification - FCC Regulatory Information Specification - IC Regulatory Information IC Statement: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. "This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment. Cet équipement est conforme à l'exposition aux rayonnements Industry Canada limites établies pour un environnement non contrôlé." Specification - IC Regulatory Information IC Statement: L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1. L'appareil ne doit pas produire de brouillage; 2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Minimum separation distance for ISED NS compliance for SCU, e.g. 10cm. Distance de séparation minimale pour la conformité ISED NS pour SCU, par ex. 10cm.Microsoft: Print To PDF