HackMotion Sensor II

General Information

The HackMotion Sensor II is a wearable device designed to track motion. It consists of several components:

• 1. Hand unit: The primary sensor unit, worn on the wrist.
• 2. Wrist unit: A smaller component, likely for data transfer or charging.
• 3. Glove attachment (Golf models only): A clip designed to attach the sensor to a golf glove.

Diagram Description: An illustration shows three main parts of the HackMotion Sensor II system. Part 1 is the Hand Unit, a rectangular device with a strap and a coiled cable. Part 2 is the Wrist Unit, a smaller, flat rectangular device. Part 3 is the Glove Attachment, a clip-like accessory intended for use with golf gloves.

© 2023 HackMotion, Kronvalda bulvāris 4, Riga, LV-1010, Latvia, European Union

Device Components and Indicators

• 4. USB Type-C port: Used for charging the device's battery.
• 5. Status indicator: A light that provides feedback on the sensor's status:
  • 5.1. Pulsating glow: Sensor is ready to connect.
  • 5.2. Steady glow: Sensor is connected.
  • 5.3. Red light: Charging. Turns off when fully charged.
  • 5.4. Red blinking light: Battery is very low.

Diagram Description: A close-up view of the sensor unit highlights key features. Label 4 points to the USB Type-C charging port. Label 5 indicates the Status Indicator light. Label 6 points to the Power Button.

? Important: When fully charged, the red status light will turn off while the charging cable is connected. You can always check the battery level within the associated application.

• 6. Power Button:
  • Press once to switch the sensor on.
  • Hold for 3 seconds to switch the sensor off.

? Note: The sensor is designed with a 5-minute auto-shutdown feature when not in use to conserve battery power.

• 7. Battery: The device offers up to 7 hours of battery life on a single charge. Use any standard USB-C cable to charge it from your computer.

Wearing the Hand Unit

The HackMotion Sensor II can be worn in two primary ways:

• A. With the palm strap: The sensor is attached to a strap designed to be worn around the palm.

  Diagram Description: An illustration shows the HackMotion sensor unit secured to a person's palm using a strap. The strap appears to wrap around the palm area.

• B. By attaching it to glove Velcro with the clip (included only with Golf sensor): For golf applications, the sensor can be clipped onto the Velcro fastening of a golf glove.

  Diagram Description: An illustration shows the HackMotion sensor unit attached to a golf glove. A clip mechanism is used to secure the sensor to the glove's Velcro area.

⚠️ Important: The palm strap is designed to self-fixate when stretched horizontally.

⚠️ Important: Do not use the sensor with magnetic strap gloves, as this may interfere with its operation.

Support and Resources

For troubleshooting tips, how-to guides, and software download links, please visit our webpage:

hackmotion.com/support-page

[Scan QR Code for quick access to support resources]

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

? Note: This equipment has been tested and found to comply with the limits for CLASS B digital devices, pursuant to Part 15 FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or experienced radio/TV technician for help.

⚠️ Warning: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

FCC SAR Compliance Statement

Your wireless wearable device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.

These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on safety standards previously set by both U.S. and international standards bodies:

• American National Standards Institute (ANSI) IEEE. C95.1-1992.
• National Council on Radiation Protection and Measurement (NCRP). Report 86.1986.
• International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1996.
• Ministry of Health (Canada). Safety Code 6.

The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless wearable devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.