Mar 23, 2023 — does not understand) that consistent with that in user manual ... [Bug 386222] Wrong license info of Panel "license" UI page.
-- TECHNICAL RELEASE NOTE ACS-DCP-11 Connectivity Panel Version 6.06.0.3 Scope of the release ACS-DCP-11, Connectivity panel SW V6.06.0.3 Software changes New · User can manually select network if automatic selection does not work by configuring Network selection (newly added to Connectivity setting->SIM Settings). Connectivity panel can be configured to work in two different modes when selecting a radio network: - Automatic network selection. Connectivity panel performs a network scan and attach to the network. This mode is recommended and the default - Manual network selection when Automatic selection does not select the best network. User can specify the network which the connectivity panel should attach to by inputting a PLMN identifier. The PLMN identifier is only provided by ABB on user inquiry · RF band reset & search (newly added to Connectivity setting->SIM settings). User can manually trigger to reset the RF band and re-search for the best band to use 23-MAR-23 PREPARED BY DELIANG WANG DOC ID: 3AXD10001867284 ABB BEIJING DRIVE SYSTEMS CO., LTD. BUILDING 401, A-10 JIUXIANQIAO BEILU, CHAOYANG D IST RI CT ,100015, Beijing, China 1/4 TECHNICAL RELEASE NOTE ACS-DCP-11 CONNECTIVITY PANEL Improved Fixed 23-MAR-23 PREPARED BY DELIANG WANG · Greatly decrease panel firmware upgrade time and increase success rate of upgrade utilizing differential firmware upgrade over the air (short for DFOTA) and resume broken download · Refine secure upgrade logic before installation. Add below condition to NOTallowed check list: - Drive is in remote mode and - Drive is Running and - Start/stop command or speed/torque reference source is configured as panel · Faster connection with Drive Composer V2.8(or later) Entry by upgrading to BLE from Classic Bluetooth · User of Powertrain get drive events (remove internal codes which customer does not understand) that consistent with that in user manual · Panel auto download firmware over the air once detect available newer one from the cloud (default setting for firmware upgrade changed to Auto download only) · Trouble shooting related: · Panel regular update NB-IoT signal strength information (update interval: 6h) · Powertrain gets informed once connectivity panel attached to unsupported drives · Panel sends events once subscription status changed (level, activated, expired) · Powertrain gets informed (from panel) when full firmware download started · Panel sends key signals/parameters at fault or warnings (can be defined by information model, parameters like Par5.80~5.88 of ACS580) · [Bug 390318] Diagnosis word "0x1101" failed to display on UI when no sim card soldered or inserted. · [Bug 386222] Wrong license info of Panel "license" UI page · [Bug 334686] Panel shows offline during remote FW download · [Bug 421799] Panel can't disable connection correctly if set to Disable during Enable procedure · [Bug 446243] Panel reboots when creating drive backup and upgrading firmware at the same time · [Bug 457569] Panel sends DeviceCreated messages without references to connected drive for update case · [Bug 463420] Manual stop firmware downloading does not work occasionally · [Bug 467113] "Agree" and "Disable warning" tip does not popup occasionally when Connectivity is disabled · [Bug 444679] Cannot display complete GUID when the parameter line has focus · [Bug 446492] Panel sends wrong event to cloud when FW version is already the latest · [Bug 446896] Panel did not update firmware version after a successful upgrade · [Bug 440350] Panel sends duplicate events to cloud · [Bug 444589] Panel gets FW download failed which triggered by default "Auto DOC ID: 3AXD10001867284 ABB BEIJING DRIVE SYSTEMS CO., LTD. Building 401, A-10 Jiuxianqiao Beilu, Chaoyang District,100015, BEIJING, CHINA 2/4 TECHNICAL RELEASE NOTE ACS-DCP-11 CONNECTIVITY PANEL start" setting when 1st time power on · [Bug 440056] Wrong objectId signal Strength · [Bug 412628] Panel lose connection often in EU Long term testing · [Bug 502495] Panel crash at next powerup when firmware downloaded while no certificate installed · Other bugs related with debug & production Availability The ACS-DCP-11 SW V6.06.0.3 from IHMM for download Compatibility Drives ACS880: · ACS880-01/04 (INU Primary control): AINL6 v2.51 or later · ACS880+ N5050: ACRLC v4.30 or later ACx580: · ACS580-01/04: ACRLC v4.30 or later Remark: · Panel V6.06.0.3 is also compitable with other drive types of ACS580 and ACS880 that running above mentioned firmware(s). Due to restrictions from CMD/Powertrain, drives other than those in above list are not supported for end(drive)-to-end(cloud) level. · For ACS880 if the connectivity panel is connected to ISU side, connection to CMD/Powertrain backend will be lost and no data will be transmitted until the panel is connected back to INU CMD /Powertrain (NB-IoT connection) Latest version of CMD/Powertrain Drive composer · Drive Composer Entry: V2.8 or later (Bluetooth connection) · Drive Composer Pro: not supported Drivetune mobile APP Drivetune V4.3 or later (Bluetooth connection) How to upgrade? The firmware upgrade instruction from ABB library : 3AXD10001867286 Type code ACS-DCP-11 23-MAR-23 PREPARED BY DELIANG WANG DOC ID: 3AXD10001867284 ABB BEIJING DRIVE SYSTEMS CO., LTD. Building 401, A-10 Jiuxianqiao Beilu, Chaoyang District,100015, BEIJING, CHINA 3/4 TECHNICAL RELEASE NOTE ACS-DCP-11 CONNECTIVITY PANEL ACS-DCP-11 is available: Drive Products: New drives with plus-code, sold through Drive Products channel (OMS): · +J461: EU Drive Connectivity Panel (ACS-DCP-11) · +J482: ABB AbilityTM Digital Powertrain for 2 years Motion Services: Stand-alone update kit through Business Online, sold through Motion Services channel (BOL) 3AXD50000866168 23-MAR-23 PREPARED BY DELIANG WANG DOC ID: 3AXD10001867284 ABB BEIJING DRIVE SYSTEMS CO., LTD. Building 401, A-10 Jiuxianqiao Beilu, Chaoyang District,100015, BEIJING, CHINA 4/4Microsoft Word for Microsoft 365