PDF preview unavailable.
Open the PDF or use the Download button.
000304880ML01
OPERATOR'S MANUAL
ENGLISH ( 1 - 28 )
WWW.AKAIPRO.COM
KEY FEATURES
· 16 pressure and velocity-sensitive MPC pads with four banks each · MPC technologies include Note Repeat, Swing, 16 Level, Full Level, and Tap Tempo · 12 assignable Q-Link knobs and faders · Dedicated transport controls transmit MMC, MIDI Clock or MIDI CC messages to DAW and
sequencing applications · MIDI output over USB and traditional MIDI I/O for controlling software and hardware · Backlit, easy-to-read screen · USB bus powered, class compliant: plug and play with one USB cable · Comes with Editor Librarian software
CONNECTION DIAGRAM
POWER (optional, not included)
COMPUTER
A NOTE ABOUT USING THE MPD26 WITH SOFTWARE:
1. Make sure that all external devices are connected to the MPD26 and that the MPD26 is connected to your computer, using the included USB cable, before opening any software applications on your computer with which you might want to use the MPD26. If the unit is not plugged in before, your software application might not recognize the MPD26 as an available device.
2. In your software application, you will need to set the MPD26 as a default MIDI input device. This is usually done in the MIDI section of the Preferences menu.
A NOTE ABOUT USING THE MPD26 WITH SOFTWARE:
The operation of the MIDI OUT port changes depending on whether or not a USB cable is connected to the MPD26.
· USB cable connected:
MIDI data from your computer is
passed to the MIDI OUT port. When a
EXTERNAL SOUND
EXTERNAL MIDI
USB cable is connected, you should
MODULE
DEVICE
activate "MIDI echo" in your sequencer if you want the MPD26 to
1. Connect a USB cable from your computer to the MPD26.
control another external device.
The unit will be powered through the USB connection. · USB cable not connected:
Alternatively, if you do not wish to use a computer in your
Whatever you play on the MPD26 is
setup or if you wish to power the MPD26 externally, please
sent to the MIDI OUT port.
plug in an optional Akai MP6-1 (6V-1A DC) power adapter.
Note: If you have another device
2. If you would like to use an external sound module, connect a 5-pin MIDI cable from the MIDI OUT of the MPD26 to the MIDI IN of the external device.
connected to the MPD26's MIDI IN port, that device's MIDI information will be ignored.
3. If you would like to use another MIDI controller in your setup, connect a 5-pin MIDI cable from the MIDI OUT of the external MIDI device to the MIDI IN of the MPD26.
1
TOP PANEL OVERVIEW
11
1
456 2
14 15 7 3
13
8
12
10
16 18 17
9
1. LCD The display is used for navigating menus, displaying data, and affecting change on MPD26's options and parameters.
2. [VALUE] (Push to Enter) This dial is used to increment and decrement Presets, parameter values and settings. This dial also functions as an [ENTER] button when it is pressed down.
3. [<] AND [>] These buttons are used for navigate through fields of menus and options. The [<] button also functions as a [CANCEL] button.
4. [PRESET] This button calls up Preset Mode. You can select and recall different Preset programs in this mode.
5. [EDIT] This button calls up Edit Mode, which allows you to edit the behavior of pads, knobs, faders and default settings for each preset.
6. [GLOBAL] This button calls up Global Mode, where MIDI reset commands and global system preferences are set.
7. [PROGRAM CHANGE] Pressing this button will enter Program Change mode. In this mode, you can send a Program Change or Program with Bank Change message to a hardware or software module.
8. [PREVIEW] This button allows you to see what value will be sent by a controller, without actually sending the value. This gives you precise control over your parameters and helps avoid erroneous controller data being sent to your devices due to the physical position of the controller. Holding down [PREVIEW] allows you to view the original value and adjust the physical position of a fader, for example, as necessary before transmitting any values.
2
9. TRANSPORT CONTROL BUTTONS These five buttons are dedicated buttons for sending transport control commands. The transport control buttons can be set to transmit either MMC (MIDI Machine Control), MMC/MIDI Clock, MIDI START/STOP or pre-assigned MIDI CC values.
10. 6 ASSIGNABLE KNOBS Each 360-degree knob can be used to send continuous control data to a desktop audio workstation or external MIDI device.
11. 6 ASSIGNABLE FADERS Each fader can be used to send continuous control data to a desktop audio workstation or external MIDI device.
12. 16 REAL MPC PRESSURE AND VELOCITY SENSITIVE PADS The pads can be used to trigger drum hits or samples on your software or hardware module. The pads are pressure and velocity sensitive, which makes them very responsive and intuitive to play.
13. PAD BANK BUTTONS These 4 buttons switch among pad banks A, B, C, D. Each bank can address a unique set of 16 sounds, giving you access of up to 64 different sounds you can trigger with the pads. The currently selected pad bank will be indicated on the LCD display.
14. [FULL LEVEL] When [FULL LEVEL] is activated, the pads always play back at a maximum velocity (127), no matter how hard or soft you hit them.
15. [16 LEVEL] When [16 LEVEL] is activated, you can use the 16 pads to
change a selected sound's velocity in 16 steps. When you press the [16 103 111 119 127
LEVEL] button, the last pad that was hit gets mapped to all 16 pads. The
pads will now output the same note number and pressure controller as 71 79 87 95 the initial pad, but the velocity is fixed at the values shown in the diagram
on the right, regardless of how hard you hit them. This allows you to have
more control over the velocity of a sound.
39
47
55
63
16. [NOTE REPEAT] Holding this button while pressing and holding down a pad causes the pad to retrigger at a rate based on the current Tempo and 7 15 23 31 Time Division settings. The Note Repeat feature can be synced to an internal or external MIDI Clock source. [NOTE REPEAT] can function as a latching or momentary button.
17. [TIME DIVISION] This button is used to specify the rate of the Note Repeat feature or Swing, which will be shown in the LCD. When [TIME DIVISION] is pressed and held, you can press one of Pads 1-8 to specify a time division or one of Pads 9-16 to specify the amount of Swing. [TIME DIVISION] is a momentary button.
18. [TAP TEMPO] This button allows you to tap in a new tempo. If the preset is reloaded, the tempo will revert to the saved tempo value. (Please note that a preset's default tempo can be set in Edit Mode). Tap Tempo does not work when the MPD26 is set to External sync.
REAR PANEL OVERVIEW
34 152
1. DC POWER ADAPTER INPUT Plug in an optional Akai MP6-1 (6V-1A DC) power adapter if you do not wish to power the MPD26 through the USB connection.
2. USB CONNECTION Plug a standard USB cable into this outlet and into the USB port of your computer. The computer's USB port will provide power to the MPD26. This connection is used to send and receive MIDI data to and from your computer and may also be used to send MIDI data from your computer to a device attached to the MIDI OUT port of the MPD26.
3. MIDI OUT Use a five-pin MIDI cable to connect the MIDI OUT of the MPD26 to the MIDI IN of an external device.
4. MIDI IN Use a five-pin MIDI cable to connect the MIDI OUT of an external MIDI device to the MIDI IN of the MPD26.
5. KENSINGTON LOCK The unit may be secured to a table or surface using this Kensington Lock slot.
3
DISPLAYING INFORMATION
As you are working with the MPD26, the LCD will help you keep track of what values are being sent to external devices. There are several kinds of information that the MPD26 will display while in use: NOTE, AFTERTOUCH (Channel Pressure), CONTROL CHANGE, MIDI MACHINE CONTROL (MMC), and PREVIEW MODE information.
NOTE
When a PAD is hit, the MPD26 will output MIDI Note On messages to trigger sounds on your DAW or external device. Each pad can have a MIDI Note Number associated with it. When you hit a pad, the screen will display the MIDI Note Number, the MIDI Port and Channel which the pad is using, as well as the pad bank and velocity (how hard you hit the pad).
Please see `Editing Pads' for more information on MIDI Notes and Pads.
MIDI PORT
NOTE
AND CHANNEL INDICATOR
PAD BANK
MIDI NOTE NUMBER
NOTE VELOCITY
VELOCITY IS ALSO DISPLAYED WITH BAR METER.
NOTE AFTERTOUCH (CHANNEL PRESSURE)
When enabled, AFTERTOUCH is MIDI data sent when pressure is applied to one of the pads after it has been struck and while it is being held down. Aftertouch will be displayed on the far right of the display as you apply pressure to the pad.
AFTERTOUCH VALUE
AFTERTOUCH VALUE IS ALSO DISPLAYED WITH BAR METER
CONTROL CHANGE
When a KNOB or FADER is used, the MPD26 will output MIDI Control Change data. This data is used to control parameters on your DAW or external sound module. When you move a knob or fader, the screen will indicate the Control Change (CC) Number, value, and MIDI Channel.
Please see `Editing Knobs & Faders' (for more information on Control Change.
CONTROL AFTERTOUCH
The knobs and faders on the MPD26 can also be set to transmit AFTERTOUCH information.
Please see `Editing Knobs & Faders' for more information on setting knobs and faders to transmit Aftertouch.
MIDI PORT
CONTROL CHANGE
AND CHANNEL INDICATOR
PAD BANK
CONTROL CHANGE NUMBER
MIDI PORT AND CHANNEL
AFTERTOUCH INDICATOR
PAD BANK
CONTROL CHANGE VALUE
VALUE IS ALSO DISPLAYED WITH BAR METER.
AFTERTOUCH VALUE
VALUE IS ALSO DISPLAYED WITH BAR METER.
4
MIDI MACHINE CONTROL (MMC)
MIDI MACHINE CONTROL (MMC) is commonly used to send transport control messages to hardware record or playback machines. For example, pressing [PLAY] on the MPD26 sends an MMCPLAY message to a connected multi-track recorder, which begins playing. When you press [STOP] on the MPD26, the deck also stops.
MMC COMMAND
PREVIEWING
When the [PREVIEW] button is held down, and a fader or knob is moved, the LCD displays the screen on the right. The display shows the assigned event and the last sent value of moved knob or fader. While the [PREVIEW] button is held, the fader of knob will not be transmitting any information until [PREVIEW] is released and the fader or knob is used again. At that point, the fader or knob will begin transmitting from the value selected in the New Value field while in Preview mode.
CONTROL CHANGE NUMBER
NEW VALUE
LAST VALUE SENT
LAST VALUE SENT
NEW VALUE
THE ADVANTAGES OF PREVIEWING
The [PREVIEW] button allows you to see what value will be sent by a controller, without actually sending the value. This gives you precise control over your parameters and helps avoid erroneous controller data being sent to your devices due to the physical position of the controller. For example, imagine that Fader 1 is being used to send three different MIDI CC numbers, depending on the preset which you are currently in. Let's assume that Fader 1 is assigned to MIDI CC#10 in Preset 1 and MIDI CC#11 in Preset 2. While in Preset 1, you adjust Fader 1 (MIDI CC#10) to a value of 40. Now you switch over to Preset 2 and adjust Fader 1 (MIDI CC#11) to a value of 80. If you now switch back to Preset 1 and try to adjust Fader 1 (MIDI CC#10), you will notice that the transmitted values will begin at 80 (instead of 40), due to the physical location of the fader. To prevent these jumps in control values, you can hold down [PREVIEW] and move Fader 1 back to a value of 40 (which will be shown in the "Last" value readout on the display). The fader will not be transmitting information while the [PREVIEW] button is held down. Once you reset the fader back to its "Last" value, you can release the [PREVIEW] button. Adjusting Fader 1 (MIDI CC#10) will now give you a nice starting point at a value of 40.
5
ABOUT MODES
The MPD26 has four different modes of operation. Each mode can be accessed by pressing the corresponding button on the MPD26. Following is a short description of each mode:
Preset Mode
This mode allows you to load, save and copy Presets. A Preset is a collection of information about how different faders, knobs, and pads will behave. Using Presets allows you to save different configurations so you can quickly load them when you need them, without having to reprogram the MPD26 every time.
Edit Mode
This mode allows you to edit the configuration of the MPD26. Edit Mode is a powerful tool for customizing your set-up. In this mode, you can make changes to how the pads, knobs and faders are behaving. For example, you may wish to have a fader or a knob transmit only a limited range of MIDI data, or you may wish to have a pad that transmits on a different MIDI Channel. You can change these and various other parameters in Edit Mode. See the Edit Mode Parameters table for a full listing of editable parameters.
Global Mode
This mode allows you to set global parameters and make general changes to how your MPD26 is functioning. The parameters that you can modify in Global Mode include Controller Resets, Pad Velocity Curves, Pad Threshold, MIDI Clock options, Display Brightness, and more.
Program Change Mode
This mode allows you to transmit various Program Change messages. In this mode, you can remotely switch between different programs on your DAW or external device directly from the MPD26.
6
PRESET MODE
What is a Preset?
A Preset is a collection of information about how the MPD26's faders, knobs and pads will behave. Using Presets allows you to save different configurations so you can quickly load them when you need them, without having to reprogram the MPD26 every time.
PRESET NAME
PRESET NUMBER
The MPD26 features different Preset banks which you can load and write to. When you turn on the MPD26, it will automatically go into Preset Mode and Preset 1 will be displayed on the screen. You can also press the [PRESET] button at any time to call up this mode. In Preset Mode you can load, save/copy and rename Presets each of these functions can be accessed through the 3 different pages. You can navigate between these pages with the [<] and [>] buttons.
LOAD PRESET Page 1
1. While you are in Preset Mode, you can change Presets with the [VALUE] dial below the screen. Turning the dial increments or decrements the current Preset number and displays the screen on the right:
When you do this, you will notice that `PRESS ENTER' will begin to blink.
2. Pressing [ENTER] loads the selected Preset. Pressing [<] or [PRESET] cancels and returns you to the Preset that was last selected.
SAVE / COPY PRESET Page 2
In Preset Mode, you can also save and copy a Preset to a new location. This allows you to save any changes that you would have made to the Preset in EDIT MODE.
Note that if you are saving the Preset to the same location (same preset number) the screen will display `SAVE TO' and if you are saving to a different location (different preset number), the screen will display `COPY TO'.
1. While you are in Preset Mode, press [>] until you see the `SAVE TO' screen similar to the one shown above.
2. You can select the location where you want to save the Preset by turning the [VALUE] knob.
When you do this, you will notice that `PRESS ENTER' will begin to blink.
3. Press [ENTER] to save current Preset to the destination. Pressing [<] or [PRESET] cancels the operation.
DESTINATION
NAME PRESET Page 3
While you are in Preset Mode, you can also change the Preset name. This way you can assign specific names to different Presets so you can better keep track and quickly access different controller configurations.
1. To name or rename the Preset, press the [>] button until you see `Preset Name' displayed on the screen. You will notice that the first letter of the name will begin blinking.
2. Turn the [VALUE] dial to change the blinking character. 3. To move between the characters, use [<] and [>]. 4. When done, press [PRESET] again. The name will be saved.
ENTER PRESET NAME IN THIS FIELD
7
EDIT MODE
Pressing [EDIT] calls up Edit Mode. In this mode, you can
NAVIGATING EDIT MODE
edit the settings of the currently selected Preset. The settings vary depending on the controller you are editing and are
1. Press [EDIT] to enter Edit Mode.
2. To select the controller you wish to edit, simply engage it this will prompt the screen to display the available event types for the particular controller (Page 1).
described on the following page.
3. If there are multiple event types for the selected controller, turn the
Please note that the changes you make will only apply to the currently selected Preset.
[VALUE] dial to select the desired event type. Press [ENTER] to view the parameters of the selected event type, if available (Page 2).
4. To move between the parameter fields on Page 2, use [<] and [>]. To change the values of the fields, turn the [VALUE] dial.
Also note that if you wish to save the changes made in Edit Mode,
5. When finished editing the controller, press [ENTER] to accept the change or press [<] to cancel.
you will need to save the current
preset.
FIELD 1
You can use the example screenshot on the right to help you determine where the Page 2 parameters
FIELD 2
described on the following page will appear on the
FIELD 3
screen.
FIELD 4
EDIT MODE PARAMETERS
CONTROLLER
PAGE 1 (EVENT TYPE)
PADS
NOTE PROGRAM CHANGE
KNOBS AND FADERS
BUTTONS
NOTE REPEAT TIME DIVISION TRANSPORT
TAP TEMPO
CONTROL CHANGE
AFTERTOUCH
CONTROL CHANGE
PROGRAM CHANGE TOGGLE/MOMENTARY
GATE/SWING DIVISION
TRANSPORT FUNCTION TEMPO
PAGE 2 (PARAMETERS)
MIDI CHANNEL (field 1) NOTE NUMBER (field 2) PLAY MODE (field 3) PRESSURE BEHAVIOR (field 4) MIDI CHANNEL (field 1) PROGRAM CHANGE NUMBER (field 2) BANK M (MSB) (field 3) BANK L (LSB) (field 4) MIDI CHANNEL (field 1) CC NUMBER (field 2) RANGE MINIMUM VALUE (field 3) RANGE MAXIMUM VALUE (field 4) MIDI CHANNEL (field 1) CC NUMBER (field 2) RANGE MINIMUM VALUE (field 3) RANGE MAXIMUM VALUE (field 4) MIDI CHANNEL (field 1) CC NUMBER (field 2) BUTTON MODE (field 4) MIDI CHANNEL (field 1) PROGRAM CHANGE NUMBER (field 2) BANK M (MSB) (field 3) BANK L (LSB) (field 4) BUTTON MODE (field 2) NOTE REPEAT GATE VALUE (field 2) NOTE REPEAT SWING VALUE (field 4) DEFAULT TIME DIVISION (field 2) MMC, MIDI, MMC/MIDI, or CTRL (field 2) BPM (field 2)
8
EDITING PADS
The pads on the MPD26 can be set to transmit Note or Program Change information when they are hit. The default operation of the pads is set to Note, which means that the pad will generate Note On/Off messages to trigger sounds. The pads may also be set up to transmit Program Change information, which allows you to use the pads to switch to different programs (instruments or sound banks) on your DAW or external device. If you would like to know more about Program Change, please read `Program Change Mode.'
What is a Note Message?
A Note Message is a MIDI message that tells an instrument to play a note. More generally, this means that Note Messages are used to start and stop sounds. When you press one of the pads, a `Note On' message is sent to your DAW or external device. This toggles a note or sample. When you release the pad, a `Note Off' message is sent. This message will stop the note or sample.
What is a Program Change?
A Program Change Message tells your DAW or external device to switch to a new program. Most often, these programs are collections of samples or instruments.
For more information, see `Program Change Mode.'
SELECT PAD EVENT TYPE IN THIS FIELD.
1. Press [EDIT] to enter EDIT MODE.
2. Press the pad which you would like to edit.
3. On Page 1, turn the [VALUE] dial to select `NOTE' or `PROG CHANGE' (Program Change) as the event type.
4. Press [ENTER] to view Page 2.
Depending on which event type you select on Page 1, parameter options on Page 2 will be different.
5. Use [<] and [>] buttons to move through fields on the second page.
The parameter fields available for each event type are outlined in the following pages.
9
NOTE PARAMETERS
MIDI CHANNEL FIELD
MIDI PORT/CHANNEL FIELD
This field sets the MIDI Port and Channel which the pad will use to transmit
1. Press [<] to messages. You can assign pads to one of two MIDI Ports, A or B, and to one of 16 MIDI Channels on each port (i.e. B11). You may also assign the pad to the MIDI Common Channel.select MIDI Port/Channel field.
2. While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI Port and Channel.
3. Press [>] to select the next field.
Note: When not used via USB, only pads assigned to port A will transmit MIDI information via the 5-pin MIDI port on the back of the MPD26.
NOTE FIELD
NOTE FIELD
This field sets the MIDI Note Number that the pad will transmit when it is hit.
1. Use [<] or [>] to select Note field.
2. While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI Port and Channel.
3. Press [>] to select the next field.
Note: Software modules or drum machines are often programmed to trigger sounds based on specific Note Numbers associated with each sample. You may have to experiment setting different Note Numbers on the MPD26 to find the range that is suited for your application.
PLAY MODE FIELD
PLAY MODE FIELD
Here, you can select whether the pad transmits Note On/Off information in a standard momentary (MTY) way like a keyboard, where hitting the pad generates a Note On and releasing it a Note Off message, or in a toggle (TGL) way where the first hit of the pad outputs a Note On, the second hit transmits a Note Off.
1. Use [<] or [>]to select Play Mode field.
2. While in Play Mode field, use [VALUE] dial to select desired Play Mode.
3. Press [>]to select the next field.
PRESSURE FIELD
PLAY MODE FIELD
Here, you can set the pad to transmit pressure information as a channel pressure message (CPR) or polyphonic pressure message (PPR).
1. Press [>] to select Pressure field. 2. While in Pressure field, use [VALUE] dial to select "OFF", "CPR", or
"PPR".
PRESSURE FIELD
When finished editing, press [ENTER] to save or [<] to cancel the changes.
10
PROGRAM CHANGE PARAMETERS
The following list of parameters can be accessed if the pad event type is set to Program Change. MIDI CHANNEL FIELD
MIDI PORT/CHANNEL FIELD
Program Change messages can be sent on one of two MIDI Ports, A or B, and one of 16 MIDI Channels on each port (i.e. A7). You may also assign Program Change to use the MIDI Common Channel.
1. Use the [<] button to select MIDI Port/Channel field.
2. While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI Port and Channel.
3. Use the [>] button to select the next field.
PROGRAM CHANGE FIELD
In this field you can set which Program Change Number the pad will transmit when it is pressed.
1. Use [<] or [>] buttons to select Program Change field.
2. While in Program Change field, use [VALUE] dial to select desired Program Change Number.
3. Use the [>] button to select the next field.
PROGRAM CHANGE FIELD
BANK M FIELD
Bank M describes the Most Significant Byte (MSB) of information. 1. Use [<] or [>] buttons to select Bank M field. 2. While in Bank M field, use [VALUE] dial to select desired value. 3. Use the [>] button to select the next field.
BANK M FIELD
BANK L FIELD
BANK L FIELD
Bank L describes the Least Significant Byte (LSB) of information. 1. Use the [<] or [>] buttons to select Bank L field. 2. While in Bank L field, use [VALUE] dial to select desired value.
Note:
You can also configure pads to send Program Change messages only, without specifying Bank M and Bank L. While editing Bank M and Bank L fields of a pad, use [VALUE] dial to set Bank M and Bank L to `OFF' (beyond 000). This will cause the pad to transmit only a Program Change message.
When finished editing, press [ENTER] to save or [<] to cancel the changes.
11
EDITING KNOBS & FADERS
The knobs and faders on the MPD26 can be set to transmit Control Change or Aftertouch information. In addition, the endless knobs may also be assigned as an Increment/Decrement function. The default operation of knobs and faders is to transmit Control Change information.
What is Control Change?
Control Change refers to the use of MIDI Continuous Controller data. Continuous Controller (CC) data are MIDI messages capable of transmitting a range of values, usually 0-127. CC's are commonly used for controlling volume, pan, and other parameters on your DAW or sound module.
What is Aftertouch?
Aftertouch refers to MIDI data sent when pressure is applied to a pad after it has been struck and while it is being held down. Aftertouch is often used to control vibrato, volume, and other parameters.
SELECT EVENT TYPE IN THIS FIELD.
1. Press [EDIT] to enter EDIT MODE.
2. Move the fader or turn the knob.
3. On Page 1, turn the [VALUE] dial to select `CTRL CHANGE' (Control Change) or `AFTERTOUCH' as the event type.
4. Press [ENTER] to view Page 2.
Depending on which event type you select on Page 1, parameter options on Page 2 will be different.
5. Use [<] and [>] to move through fields on the second page.
The parameter fields available for each event type are outlined in the following pages.
12
CONTROL CHANGE PARAMETERS
The following list of parameters can be accessed if the event type for the knob or fader is set to Control Change.
MIDI CHANNEL FIELD
MIDI PORT/CHANNEL FIELD
This field sets the MIDI Port and Channel which the knob or fader will use to transmit messages. You can assign knobs and faders to one of two MIDI Ports, A or B, and to one of 16 MIDI Channels on each port (i.e. A14). You can also assign a knob or fader to use the MIDI Common Channel.
1. Press [<] to select MIDI Port/Channel field.
2. While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI Port and Channel.
3. Press [>] to select the next field.
Note: When not used via USB, only knobs and faders assigned to port A will be transmitted via the 5-pin MIDI port on the back of the MPD26.
CONTROL CHANGE FIELD
CONTROL CHANGE FIELD
In this field you can set which MIDI CC # the knob or fader will transmit when it is used.
1. Use [<] or [>] to select Control Change field.
2. While in Control Change field, use [VALUE] dial to select desired Control Change Number.
3. Press [>] button to select the next field.
Note: To control a parameter in your DAW or sound module with a knob or fader, both the parameter and the physical controller should be set to the same Controller Number.
MINIMUM RANGE FIELD
MINIMUM RANGE FIELD
This field is used to specify the minimum value that the knob or fader can output.
1. Use [<] or [>] to select Minimum Range field.
2. While in Minimum Range field, use [VALUE] dial to select desired minimum value.
3. Press [>] button to select the next field.
Tip: Sometimes you might not want the full 0-127 range of control that a fader automatically defaults to. Often, reducing the value range of the fader might give you more precise control over the parameter it is controlling. For example, if you are using one of the faders to control a synced delay line, there might only be about 10 available values for the sync delay time (1/2, 1/4, 1/8 note, etc.). Therefore, it wouldn't make much sense to have the fader transmit the full 128 MIDI control values, since this only gives you a tenth of the full fader range. Instead, try setting the maximum value of that fader to 10.
MAXIMUM RANGE FIELD
MAXIMUM RANGE FIELD
This field is used to specify the maximum value that the knob or fader can output.
1. Use the [<] or [>] buttons to select Maximum Range field.
2. While in Maximum Range field, use [VALUE] dial to select desired maximum value.
Tip: Setting the maximum value of a controller lower than the minimum value will cause the knob or fader to behave inversely. For example, if you are controlling an interface or plug-in that operates with a drawbar structure, such as organ instruments, it might be more intuitive to invert your faders.
When finished editing, press [ENTER] to save or [<] to cancel the changes.
13
AFTERTOUCH PARAMETERS
For some applications, you might wish to use the faders or knobs as Aftertouch controllers. In this scenario, the knob or fader will transmit Aftertouch information which could be used to control, say, vibrato or tremolo. The following list of parameters can be accessed if "Aftertouch" is selected as the event type for the knob or fader.
MIDI CHANNEL FIELD
MIDI PORT/CHANNEL FIELD
This field sets the MIDI Port and Channel which the knob or fader will use to transmit messages. You can assign knobs and faders to one of two MIDI Ports, A or B, and to one of 16 MIDI Channels on each port (i.e. A14). You can also assign a knob or fader to use the MIDI Common Channel.
1. Press [<] to select MIDI Port/Channel field.
2. While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI Port and Channel.
3. Press [>] to select the next field.
Note: When not used via USB, only knobs and faders assigned to port A will be transmitted via the 5-pin MIDI port on the back of the MPD26.
MINIMUM RANGE FIELD
MINIMUM RANGE FIELD
This field is used to specify the minimum value that the knob or fader can transmit.
1. Use [<] or [>] buttons to select Minimum Range field.
2. While in Minimum Range field, use [VALUE] dial to select desired minimum aftertouch value.
3. Use the [>] button to select the next field.
MAXIMUM RANGE FIELD
This field is used to specify the maximum value that the knob or fader can transmit. 1. Use the [<] or [>] buttons to select Maximum Range field. 2. While in Maximum Range field, use [VALUE] dial to select desired
maximum value.
MAXIMUM RANGE FIELD
When finished editing, press [ENTER] to save or [<] to cancel the changes.
14
INCREMENT/DECREMENT PARAMETERS (knobs only)
The endless knobs on the MPD26 may also be used as an increment/decrement NRPN function. This allows you to use the knob to increment and decrement through parameters as opposed to sending an absolute value. Please note that the implementation of NRPN functions depends strictly on the software with which you will be using the MPD26. Consult your software's documentation to find out how NRPN functions are supported.
MIDI CHANNEL FIELD
MIDI PORT/CHANNEL FIELD
This field sets the MIDI Port and Channel which the knob will use to transmit messages. You can assign the knobs to one of two MIDI Ports, A or B, and to one of 16 MIDI Channels on each port (i.e. A14). You can also assign knobs to use the MIDI Common Channel.
1. Press [<] to select MIDI Port/Channel field.
2. While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI Port and Channel.
3. Press [>] to select the next field.
Note: When not used via USB, only knobs assigned to port A will be transmitted via the 5-pin MIDI port on the back of the MPD26.
BANK M FIELD
Bank M describes the Most Significant Byte (MSB) of information. 1. Use [<] or [>] buttons to select Bank M field. 2. While in Bank M field, use [VALUE] dial to select desired value. 3. Use the [>] button to select the next field.
BANK M FIELD
BANK L FIELD
Bank L describes the Least Significant Byte (LSB) of information. 1. Use the [<] or [>] buttons to select Bank L field. 2. While in Bank L field, use [VALUE] dial to select desired value.
BANK L FIELD
When finished editing, press [ENTER] to save or [<] to cancel the changes.
15
EDITING NOTE REPEAT
The MPD26 features the Note Repeat function, which can be found on our legendary Music Production Center (MPC) models. With Note Repeat enabled, you can repeatedly trigger a sound by simply holding down a pad. The sound will be retriggered at a rate equivalent to the currently selected Time Division. With the Note Repeat feature, you can record a phrase that would be difficult to record in real time, such as 16 beat hi hat, snare roll, etc...
The following Note Repeat settings may be edited:
BUTTON MODE (TOGGL/MOTRY) This describes whether the [NOTE REPEAT] button functions in a momentary or toggle fashion. GATE The gate parameter describes the duration of the repeated notes. SWING The swing parameter describes the swing offset for the even notes in the repeated sequence.
SELECT PROPERTY PRESS ENTER TO EDIT
1. To edit Note Repeat, press [EDIT] to enter Edit Mode. 2. Now select Note Repeat for editing by pressing [NOTE REPEAT]. 3. You will see Page 1 displayed on the screen (shown on the left). 4. Turn the [VALUE] dial to select the property you wish to edit -
(Toggl-Motry) or (Gate Swing). 5. Press [ENTER] to edit the selected property.
Please refer to the following illustrations to help you understand how Note Repeat parameters affect the triggered sequence:
Let's take the kick drum sequence shown on the left as an example. This sequence was generated with the Note Repeat feature with a Time Division setting of 1/4 note.
Now, if we decrease the Gate parameter, the sequence will look like this.
Conversely, if we increase the Gate parameter, the sequence will look like this.
Now, if we were to add some swing to our original sequence, we will end up with a sequence like this. Notice how each even note in the sequence is being pushed back in time to create the swing effect. If we keep increasing the Swing value, these notes will occur closer and closer to the odd notes.
Please note:
For the Gate effect to be perceived, the sounds you are triggering need to have a long decay.
16
NOTE REPEAT BUTTON MODE
The following screen will appear if you select "TOGGL-MOTRY" on Page 1. In this field, you can select whether the [NOTE REPEAT] button will behave in a momentary (MTY) fashion, where pressing the button turns on the Note Repeat function and releasing it turns it off, or in a toggle (TGL) manner, where pressing the button turns on the Note Repeat function and pressing again turns it off.
1. While in Button Mode field, use [VALUE] dial to select Button Mode (Toggle or Momentary).
2. Press [ENTER] to accept change.
BUTTON MODE
NOTE REPEAT PARAMETERS GATE, SWING
The following parameters can be adjusted if you select "GATE SWING" on Page 1. GATE
Select the Note Repeat Gate in this field. 1. While in Gate field, use [VALUE] dial to select Gate duration. 2. Use the [>] button to select the next field.
GATE FIELD
SWING
SWING FIELD
Select the Note Repeat Swing in this field. 1. Use the [>] button to select the Swingfield 2. While in Swing field, use [VALUE] dial to select the desired Swing
value. 3. Press [ENTER] to accept changes.
17
EDITING TIME DIVISION
The Time Division feature works in conjunction with Note Repeat. When Note Repeat is enabled and a pad is held down, the MPD26 will output notes at a rate equivalent to the Time Division setting. To change to a new Time Division setting, press and hold [TIME DIVISION] and select a new rate by pressing one of Pads 816 (1/4, 1/4T, 1/8, etc.). To select the amount of Swing, press and hold [TIME DIVISION] and press one of Pads 9-16 (54%, 56%, etc.). The adjustments you make to either parameter will be shown in the LCD. Please refer to the following illustrations to better understand how the Time Division feature works with Note Repeat:
With an 1/8 note Time Division setting, the sequence will look like this.
With an 1/8T note Time Division setting, the sequence will look like this.
With a 1/16 note Time Division setting, the sequence will look like this.
With a 1/16T note Time Division setting, the sequence will look like this.
With a 1/32 note Time Division setting, the sequence will look like this.
With a 1/32T note Time Division setting, the sequence will look like this.
PRESS ENTER TO EDIT
1. To edit Time Division settings, press the [EDIT] button to enter Edit Mode.
2. Now select Time Division for editing by pressing [TIME DIVISION]. 3. You will see Page 1 displayed on the screen (shown on the left). 4. Press [ENTER] to edit the Time Division settings.
DEFAULT TIME DIVISION
Each Preset can have a default Time Division setting which is set every time the Preset is loaded. 1. While in Default Time Division field, use [VALUE] dial to select the
default Time Division (1/4, 1/4T, 1/8, etc.) 2. Press [>] to select the next field.
DEFAULT DIVISION FIELD
18
EDITING TRANSPORT CONTROL
The MPD26 can be configured to send transport control information in a variety of ways: MMC (MIDI Machine Control), MMC/MIDI, MIDI, or CTRL. Some applications and devices have dedicated MMC functions and will only respond to MMC messages, while others may not have reserved MMC functions but implement transport control via MIDI SysEx or MIDI CC messages. To account for these scenarios, we have provided a way to edit the messages sent by the transport control buttons. This allows you to customize the MPD26's transport to work with your application or external device.
1. To edit transport control settings, press [EDIT] to enter Edit Mode. 2. Now select the transport control for editing by pressing [ << ], [ >> ],
[STOP], [PLAY], or [REC]. 3. You will see Page 1 displayed on the screen (shown on the left). 4. Press [ENTER] to edit transport control settings.
PRESS ENTER TO EDIT
5. When on Page 2, use the [VALUE] dial to select the format of the transport control messages (MMC, MMC/MIDI, MIDI, CTRL).
6. Press [ENTER] to accept the change or [<] to cancel.
TRANSPORT CONTROL MESSAGE FORMAT
EDITING TAP TEMPO
Each Preset on the MPD26 can have a default tempo associated with it. Every time that the Preset is loaded, the BPM setting will be loaded automatically.
1. To edit the default tempo, press [EDIT] to enter Edit Mode. 2. Now select tempo for editing by pressing [TAP TEMPO]. 3. You will see Page 1 displayed on the screen (shown on the left). 4. Press [ENTER] to edit the default tempo for the current Preset.
PRESS ENTER TO EDIT
PRESS ENTER TO EDIT
5. On Page 2, use the [VALUE] dial to adjust the default tempo. 6. Press [ENTER] to accept the change or [<] to cancel.
BPM FIELD
19
GLOBAL MODE
In Global Mode, you can send global messages and make general changes to the way that your MPD26 functions. Global Mode options are organized under different pages and include the list of options shown below.
NAVIGATING GLOBAL MODE
1. Press [GLOBAL] to enter Global Mode. 2. Use [<] and [>] to navigate through the available pages of
options (shown below). 3. Use the [VALUE] dial to change settings, values or select a
message on the selected page. 4. Press [ENTER] to accept the change or send a message
or press [<] to cancel.
KILL MIDI MIDI COMMON CHANNEL
LCD CONTRAST PAD SENSITIVITY PAD VELOCITY CURVE
PAD THRESHOLD MIDI CLOCK
TAP TEMPO AVERAGE SAVE SETUP SYSEX TX VERSION
Send an All Notes Off or Reset Controllers message
Select which MIDI channel will be used as the Common Channel. Adjust the contrast of the display.
Adjust how sensitive the pads are to the touch.
Adjust how the pads will output MIDI velocity, based on the force applied to them. Adjust the threshold of minimum force required to activate a pad. Select Internal or External MIDI Clock source.
Select the number of taps to be averaged in determining tempo. Save the current global settings.
Transfer a Preset via SysEx.
Check the current firmware version.
Page 1 Page 2 Page 3 Page 4 Page 5
Page 6 Page 7 Page 8 Page 9 Page 10 Page 11
20
KILL MIDI Page1
KILL MIDI allows you to send either an ALL NOTES OFF message on each MIDI Channel or a RESET ALL CONTROLLERS command.
ALL NOTES OFF is a special MIDI message used to turn off any notes that might be playing on the MPD26. It is often used to recover from erroneous stuck notes.
RESET ALL CONTROLLERS is a MIDI message used to return all values such as aftertouch to their default settings. Control reset will return all values to their default settings.
1. Press [GLOBAL] to enter Global Mode. "Kill MIDI" will be the first option which appears on the screen.
2. Turn [VALUE] dial to select either an ALL NOTES OFF or a RESET ALL CONTROLLERS message.
3. Press [ENTER] to transmit the message.
MIDI COMMON CHANNEL Page 2
MIDI COMMON CHANNEL FIELD
LCD CONTRAST Page 3
You can assign the MIDI Common Channel to a specific MIDI Channel (i.e. A1). Any and all pads, knobs or faders assigned to the MIDI Common Channel (CC) will transmit MIDI information via the channel number that you select in this field.
1. While in Global Mode, press [>] button to scroll to MIDI Common Channel (page 2).
2. Turn [VALUE] dial to select desired MIDI Channel.
3. Press [ENTER] to set the MIDI Channel.
Note: If you change which channel the MIDI Common Channel is using, you need to set any device that is controlled by the Common Channel to receive on the same channel.
The contrast of the LCD can be adjusted for optimal viewing. 1. While in Global Mode, press [>] to scroll to LCD CONT (page 3). 2. Turn [VALUE] dial to select a contrast level. 3. Press [ENTER] to set contrast level.
LCD CONTRAST
PAD SENSITIVITY Page 4
PAD SENSITIVITY FIELD
PAD SENSITIVITY allows you to adjust how sensitive the pads will be to the touch. Adjust this setting if you find it hard to achieve maximum velocity when you hit the pads hard, or if you are getting high velocities when you hit softly.
If the Pad Sensitivity number is set to low number, it's harder to get a high velocity value even if you hit a pad hard. If the Pad sensitivity number is set to a high number, it may become too easy to get high velocities even when you hit a pad softly.
1. While in Global Mode, press [>] to scroll to PadSens (page 4).
2. Turn [VALUE] dial to change Pad Sensitivity.
3. Press [ENTER] to set Pad Sensitivity.
21
PAD VELOCITY CURVE Page 5
PAD VELOCITY CURVE FIELD
A PAD VELOCITY CURVE describes how the pads on the MPD26 are outputting MIDI velocities, based on a certain ratio of the input / output velocity that characterizes the particular curve. The Pad Velocity Curve feature is intended to help you optimize the pads on the MPD26 for your particular playing style and can add expressivity and control to your performance. If you find it difficult to achieve a comfortable velocity range for your playing style (you cannot get a velocity of 127 even if you hit the pad very hard, or vice versa, you get velocity 127 easily even if you hit the pad softly) you can adjust the velocity curve as desired.
1. While in Global Mode, press [>] to scroll to PadCurve (page 5).
2. Turn [VALUE] dial to change the Pad Velocity Curve (the 4 curves are shown below).
3. Press [ENTER] to set Pad Velocity Curve.
MIDI VELOCITY
WEAK
STRENGTH OF HITTING PAD
STRONG
PAD THRESHOLD Page 6
PAD THRESHOLD FIELD
PAD THRESHOLD is the minimum force required to activate the pads. If you experience "ghost" triggering due to stage vibrations, you may wish to set this threshold higher. On the other hand, if you find it difficult to trigger sounds when playing the pads lightly, you may wish to set this value to a lower number.
1. While in Global Mode, press [>] to scroll to PdThresh (page 6).
2. Turn [VALUE] dial to select value.
3. Press [ENTER] to set Pad Threshold.
MIDI CLOCK Page 7
MIDI CLOCK FIELD
MIDI CLOCK is used to synchronize devices together. In addition, MIDI Clock on the MPD26 is used to synchronize the Note Repeat feature. The MPD26 can be a master or slave for MIDI Clock transmission and reception.
1. While in Global Mode, press [>] to scroll to MIDI CLK (page 7).
2. Turn [VALUE] dial to select "Internal" if you would like to generate MIDI Clock internally or "External" if you would like to slave the MPD26 to an external MIDI Clock source.
3. Press [ENTER] to set MIDI Clock source.
Note: If "External" has been selected as a MIDI Clock source, the [TAP TEMPO] button will be disabled.
22
TAP TEMPO AVERAGE Page 8
TAP AVERAGE FIELD
When using [TAP TEMPO] button to set the tempo, the MPD26 averages a number of taps in order to determine the tempo. You can set the number of taps used to determine the TAP TEMPO AVERAGE in this field.
1. While in Global Mode, use [>] button to scroll to Tap AVG (page 8).
2. Turn [VALUE] dial to select number of taps.
3. Press [ENTER] to set tap average.
SAVE SETUP Page 9
SAVE SETUP allows you to save any changes you may have made to the global parameters.
1. While in Global Mode, press [>] to scroll to Globals (page 9). You will see "Save Setup" displayed on the screen.
2. Press [ENTER] to save all the global settings on the MPD26.
PRESS ENTER TO SAVE
SYSEX TX Page 10
CHOOSE PRESET
PRESS ENTER TO TRANFER
VERSION Page 11
SYSEX TX allows you to transfer Preset data from the MPD26 via SysEx. This data includes Controller Numbers, MIDI Channels and various other parameters. 1. While in Global Mode, press [>] to scroll to SysEx Tx (page 10). 2. Turn the [VALUE] dial to select which Preset's information you
would like to transfer. 3. Press [ENTER] to save all the global settings on the MPD26.
SysEx transfers to the MPD26
You can also load preset data into the MPD26 from an external source by "playing" a SysEx file into the MPD26. This can be done with a variety of SysEx applications, many of which are widely and freely available over the Internet.
1. Make sure that the device is connected to the MPD26 either via the USB or the MIDI IN port.
2. Make sure that you are in Preset Mode. 3. "Play" the SysEx file on your external device or computer.
Please note that when transferring SysEx information into the MPD26, the data will override the data of the original Preset which was sent to your SysEx editor. For example, if you transfer Preset 5 to your SysEx editor and then send it back to the MPD26, the data will overwrite Preset 5.
VERSION allows you to see what version of the operating system and firmware is currently loaded onto the MPD26. While in Global Mode, press [>] to scroll to Ver (page 11) for version information.
23
PROGRAM CHANGE MODE
A Program Change, often referred to as a Patch Change, is a MIDI message used for sending data to devices to cause them to change to a new program.
There are two different types of Program Change messages on the MPD26:
PROG CHANGE This event will transmit a regular Program Change message (0127) to your DAW or an external device, allowing you to switch between 128 different program banks.
NAVIGATING PROGRAM CHANGE MODE
1. Press the [PROGRAM CHANGE] button.
2. On Page 1, use the [VALUE] dial to select a Prog Change or Prog+Bank message on and press [ENTER].
3. On Page 2, use the [<] and [>] buttons to move through the different options and use the {VALUE] dial to change them.
4. Press [ENTER] to send the message.
PROG+BANK This event transmits a Program Change message (0-127), along with a Bank L (Least Significant Byte) Change message (0-127) and a Bank M (Most Significant Byte) Change message (0-126), which allows access of up to 16384 different program banks. You can use PROG+BANK if your DAW or external device supports LSB and MSB.
PROG CHANGE (Program Change)
PROG CHANGE allows you to transmit a regular Program Change message.
1. Select PROG CHANGE with the [VALUE] dial.
2. Press [ENTER] to see the next page of parameters.
3. Press the [<] button to access the MIDI CH field this is the MIDI Channel which will be used to transmit the Program Change message. You can change the MIDI Channel by turning the [VALUE] dial. Then, press [>] to go to the next field.
4. In the PROG field, choose the program number with the [VALUE] dial.
5. Press [ENTER] to send the Program Change message.
PROG+BANK (Program Change with Bank Change)
PROG+BANK allows you to send a Program Change with Bank Change message to your DAW or external sound module. 1. Select PROG+BANK with the [VALUE] dial. 2. Press [ENTER] to see the next page of parameters. 3. Press the [<] button to access the MIDI CH field this is the MIDI
Channel which will be used to transmit the message. You can change the MIDI Channel by turning the [VALUE] dial. Then, press [>] to go to the next field. 4. In the PROG field, choose the program number with the [VALUE] dial. Press [>] to go to the next field. 5. In the BANK M field, select the MSB (Most Significant Byte) of information. Press [>] to go to the next field. 6. In the BANK L field, select the LSB (Least Significant Byte) of information. 7. Press [ENTER] to send the Bank and Program event.
24
RESETTING FACTORY DEFAULTS
If you ever would like to restore all the presets to the factory default, do the following: 1. Press [>] - this will open the SAVE screen. 2. Press [>] again - This will open the PRESET NAME screen. 3. Press [>] to move past each letter in the current program's name
until the last character is reached. 4. Press [>] one more time - The FACTORY will be displayed. 5. Press [ENTER] to restore factory defaults.
**WARNING** Pressing [ENTER] will erase ALL presets and reload the Factory
Presets that shipped with the unit!!
25
FREQUENTLY ASKED QUESTIONS
Question: Can the MPD26 be synced to external devices? Answer: Yes, the MPD26 can receive MIDI Clock through both the USB and the MIDI IN connection. This
means that you can synchronize the tempo-based Note Repeat to an external source. To synchronize the MPD26 to an external MIDI Clock source, please enter Global Mode, scroll to MIDI Clock and select "External".
Question: Do I need to use a power adapter if I am using the MPD26 with a computer? Answer: No. The MPD26 will draw power directly from the USB port. However, if your USB port does not
supply enough power or if you are using a USB hub, it may be necessary to use the adapter.
Question: Does the MPD26 have internal sounds? Answer: No. The MPD26 is a MIDI-controller, which means that it does not contain any sounds inside but
is instead used to control external sound devices, such as hardware and software synthesizers, sequencers and drum machines.
Question: What software applications is the MPD26 compatible with? Answer: The MPD26 is compatible with any software or hardware device which supports the MIDI
protocol. Please consult your specific hardware or software device's documentation for instructions on enabling the MPD26 as a MIDI input device.
Question: Can I use the MPD26 as a MIDI interface for other MIDI devices? Answer: Yes. The MPD26 functions as a MIDI interface and can be used to send or receive MIDI to and
from other MIDI devices connected to it.
Question: Can I control multiple devices with the MPD26? Answer: Yes. The MPD26 can transmit information on 16 MIDI channels on 2 ports for a total of 32
different MIDI Channels.
Question: How many different Presets can the MPD26 hold? Answer: The MPD26 can hold 30 Preset settings, which allow you to store different configurations for use
with various software and hardware modules. Presets can easily be copied, edited and stored for quick recall of desired configurations.
Question: Can I send Program Change messages to my software or hardware devices? Answer: Yes. You can send program change messages in Program Change mode. In addition, pads may
also be assigned to transmit program change messages.
Question: Are the pads on the MPD26 velocity and pressure sensitive? Answer: Yes. The MPD26 sports real MPC velocity and pressure sensitive pads. This allows you to be
extremely expressive with your programming and performance.
Question: What type of pads is used on the MPD26? Answer: The MPD26 features the same exact pads which are used on the Akai MPC2500.
Question: Are the knobs on the MPD26 endless? Answer: The knobs on the MPD26 are endless pots. This allows you to limit the range of the knobs, as
well as use them as increment/decrement controls. Please note that your software application must be able to receive and recognize NRPNs for Increment/decrement functions to work.
Question: I see 6 knobs, 6 faders, and 16 pads. Is that all I get? Answer: No. The MPD26 features multiple banks of pads, which can be accessed with the [PAD BANK]
button. There are 4 different pad banks which give you a total of 64 (4x16) pads.
26
TROUBLESHOOTING
PROBLEM
CAUSE
The display does not light up.
No power.
MPD26 not properly connected.
No sound from target device.
Notes sustain continuously. Note Repeat feature is not synchronized to my clock source. My Seq/DAW is set to send clock but Note Repeat is not working. My fader or knob works in reverse.
Transport control does not work. I am only hearing one sound when I hit different pads.
MPD26 connected after software application has started. Problem is caused by use of a USB hub.
Software application not set to receive MIDI data from the MPD26.
MPD26's MIDI channel not the same as application's incoming MIDI chanel.
Stuck notes due to incomplete MIDI data.
Clock source on MPD26 set to "Internal".
Software DAW is not in play mode.
Controller minimum value is set higher than its maximum.
Software does not support MMC messages, MIDI START/STOP or the MIDI CC mode.
16 Level feature is engaged.
The pads always play at maximum velocity (127).
Full Level feature is engaged.
SOLUTION
Please make sure that the MPD26 is connected to your computer and that the computer is powered on.
If using a power adapter, please make sure that the adapter is plugged into a live power outlet. Check your computer's USB connection to confirm that the MPD26 is recognized. If necessary, replug the connection and restart your computer. If controlling an external hardware module, make sure that the MIDI cable is connected from the MPD26 to the device's MIDI IN port.
Restart the software application with the controller plugged in.
Unplug the MPD26 from the USB hub and connect directly to the computer. Ensure that the MPD26 or "USB" MIDI device is listed as an active MIDI source in your application. Usually, the MIDI settings can be accessed through the application's Preferences menu. Make sure that the MPD26 is sending MIDI information on the channel that the target device expects.
Turn the unit's power off, wait a moment and then turn it on again.
In Global Mode, change the MIDI Clock setting to "External". Also, make sure that the software you are using is set to send MIDI Clock to the MPD26.
If your software DAW is not playing, it will not be sending clock.
Edit the controller and set the minimum value to be lower than the maximum.
Edit the transport control to send MIDI messages instead. Make sure that the Transport mode you are using on the MPK matches the receive modes of your software. When engaged, the 16 Level function will map the last hit pad to all 16 pads. Deactivate 16 Level to return to normal operation. When engaged, the Full Level function will cause all the pads to output maximum velocity, no matter how hard they are hit. Turn off Full Level to return to normal operation.
27
TECHNICAL SPECIFICATIONS
GENERAL Display Dimensions (WxDxH) Weight Power Number of Presets MIDI output channels over USB MIDI output channels from 5-pin MIDI Drum pads Drum pad banks Faders 360 degree knobs
Accessories
INPUTS/OUTPUTS MIDI inputs MIDI outputs USB DC IN
custom LCD w/ backlight 314mm x 289mm x 70mm 2.2kg ~100mA, 5V DC via USB ~1A, 6V DC via external adaptor 30 48 (16 channels x 3 ports) 16 16 (velocity and pressure sensitive) 4 6 6 Quickstart Guide USB cable Software CD
5-pin DIN x 1 5-pin DIN x 1 Slave connector x 1 (MIDI over USB) 6V DC, 1A
CONTACT INFORMATION
Please visit the Akai Professional website (www.akaipro.com) regularly for additional information, news and firmware upgrades for the MPD26.
For additional technical support:
EMAIL: support@akaipro.com TEL: 401.658.4032 (U.S)
28
Rev. A
WWW.AKAIPRO.COM
