ATTEN Soldering Station

The soldering iron needs to be tested before it leaves the factory, so the soldering tip may cover a small amount of tin, and the casing will be slightly yellowing, which is a normal phenomenon.

Copyright information

The design of this product (including internal software) and its accessories is under the protection of relevant state laws. Any violation of the relevant rights of our company will be subject to legal sanctions. Users shall consciously abide by the relevant state laws when using this product.

Disclaimer

We will take no responsibility for any personal injury or property damage caused by reasons other than the product quality problem, which may include force majeure (natural disasters, etc.) or personal behavior during the operation of this product. This manual is organized, compiled, and released by SHENZHEN ATTEN TECHNOLOGY CO., LTD. according to the latest product features. We will not be responsible for further notice of the subsequent improvement of the product and this manual.

Safety Precautions

Caution: Misuse of this product may lead to serious injury to the user or material damage to the object involved.

To avoid electric shock or injury to the human body or fire hazard, the following basic rules must be observed when using the equipment. In order to ensure personal safety, only parts and accessories approved or recommended by the original factory can be used, otherwise serious consequences may occur!

WARNING: When using this product, the soldering pencil/soldering tip, with the temperature up to 80-480°C, may cause burns to the user or cause a fire due to improper application. Users shall strictly observe the following rules:

• Keep this product away from flammable materials.
• Keep the product out of children's reach.
• Do not use this product if you are inexperienced or have no sufficient necessary knowledge without the guidance of related personnel.
• Do not use this product under wet environment or with wet hands to avoid electric shock.
• Do not modify this product and its accessories without authorization.
• Please turn off the power when replacing parts and iron tips, and not resume the use until the equipment is completely cooled down.
• Please use the accessories from the original factory when replacing the product parts.
• Make sure to turn off the power switch when the equipment is temporarily stopped or out of use.

Essential Knowledge for Users

Users are required to have basic knowledge of common sense and electrical operations before using the product. Minors shall use the product under the guidance of a professional or guardian.

Packing List

• Main unit (including machine, power cable and handle) x 1pc
• Soldering wire holder x 1pc
• User manual x 1pc

Features

• This product is designed with a nixie tube display.
• Combined soldering station with soldering stand.
• MCU controlled temperature calibration with PID system equipped, adjust temperature by knob button, easy to operate.
• The handle structure is ergonomically designed for comfortable grip.
• The heating wire and sensor are made of PTC material, which is quick in temperature rise and precise in temperature control.
• Auto-standby, auto-shut down is available.
• Uses a 3-cored power cable.

Appearance and Control Panel

The control panel features the following components:

• 1. Power button: Used to turn the unit on/off.
• 2. Nixie tube display: Shows temperature settings and status.
• 3. Indicate light for temperature unit: Shows the current temperature unit (°C or °F).
• 4. Soldering wire holder: Holds the soldering wire spool.
• 5. Temperature adjustable knob button: Used to set the desired temperature.
• 6. Temperature unit switch / temperature lock: Press to switch temperature units (°C/°F) or press and hold for 3 seconds to lock/unlock temperature.
• 7. Soldering handle: The ergonomic handle for the soldering iron.
• 8. Soldering stand: Provides a safe place to rest the hot soldering iron.
• 9. Soldering tip slot: Where the soldering tip is inserted into the handle.
• 10. Tip cleaner location: Designated area for tip cleaning materials (e.g., brass sponge).

(Diagram description: A diagram shows the soldering iron handle connected to the main unit, with callouts pointing to the power button, display, indicator light, wire holder, knob, unit switch, handle, stand, tip slot, and tip cleaner location.)

Specification

Operational Guide

1. Power Button

Turn on the device by connecting it to power. Set the desired temperature using the knob; it will be shown on the nixie tube display. After 3 seconds, the display will show the real-time temperature of the soldering tip.

2. Temperature Setting

While the device is operating, you can rapidly adjust the temperature using the temperature knob. The setting temperature will be displayed during adjustment. After stopping the adjustment for 3 seconds, the actual soldering tip temperature will be displayed. The temperature range is 80°C to 480°C.

(Visual description: The display shows '480' as the setting temperature, and '350' as the actual measured temperature. Another state shows '480' as 'Up to be setting temperature'.)

3. Temperature Locking Function

To lock the current temperature, press the LOCK/°C/°F button for 3 seconds while the unit is in working mode. The temperature will not change when turning the knob, and the display will show "LOC". To unlock, press the LOCK/°C/°F button again for 3 seconds.

(Visual description: The display shows '480', with text indicating 'Turn the knob button' and 'Loc'.)

4. Switching Temperature Unit

Press the LOCK/°C/°F button simultaneously while in working mode to switch between Celsius (°C) and Fahrenheit (°F). The indicator light for the temperature unit will change accordingly.

(Visual description: The display shows '480' and '896' in sequence, implying a unit change.)

5. Auto Standby Function

When the soldering iron is not in use and is placed on the iron holder, the station will automatically enter standby mode after 10 minutes. The heater will be set to 200°C, and the nixie tube will display "STB". Picking up the soldering iron will return the unit to normal working mode.

6. Auto Sleep Function

In auto standby mode, the soldering station will automatically enter sleep mode after 20 minutes. The nixie tube will display "SLP", and the heating core will not be heated. The unit will return to normal work mode by adjusting the knob or pressing any button. (Note: The unit will auto sleep if it remains unused and no operations are performed.)

(Visual description: The display shows 'SLP' and '203'.)

7. Warning

If "E02" is shown on the display screen, it indicates an error with the sensor.

(Visual description: The display shows 'E02'.)

Soldering Tips

The following soldering tips are available for the ST-2090D station:

• T900-0.8D
• T900-1.2D
• T900-1.6D
• T900-K
• T900-3.2D
• T900-1CF*
• T900-1.5CF*
• T900-2.4D
• T900-R
• T900-RT
• T900-SI
• T900-S4
• T900-1.2LD
• T900-2C
• T900-H
• T900-SB
• T900-2CF*
• T900-3C
• T900-1.8H
• T900-B
• T900-S10*
• T900-3CF*
• T900-4C
• T900-4CF*
• T900-S11*

(Diagram description: A detailed diagram illustrates various soldering tip shapes and sizes, with model numbers and dimensions provided for each.)

Product Warranty

This product is guaranteed for two years from the date of purchase (excluding consumables such as the heating core). If any quality problem is found within the guarantee period, ATTEN will provide maintenance free of charge. For products beyond the warranty period, ATTEN provides life-long maintenance services.

For products damaged due to users' improper application or unauthorized changes to the product parts, ATTEN only provides limited warranty service.

In case of a product fault, please send the faulty product to the designated maintenance shop for maintenance. Service centers and personnel unauthorized by the factory are prohibited from carrying out any maintenance on the product.

After-sales Contact

After-sales service department: Tel: (+86) 755-26976387

SHENZHEN ATTEN TECHNOLOGY CO.,LTD.

Address: Floor 8, Building 2, Senyang High-tech park, 7 West Road High-tech Park, Guangming New district, Shenzhen 518132, China

Telephone: 86-755-8602 1373

Fax: 86-755-8602 1365

Web: www.atten.com

Facebook: https://www.facebook.com/attencn/

E-mail: sales@atten.com.cn