User Manual for Jandy models including: TruGuard Mineral Sanitizer
Jandy TruGuard Mineral Sanitizer | TRUGUARD | Pool Products Canada
Mineral Filter for Pool: Mineral Sanitizer | Jandy
File Info : application/pdf, 20 Pages, 4.82MB
DocumentDocumentINSTALLATION AND OPERATION MANUAL ENGLISH | ESPAÑOL Jandy TruGuardTM with Nature2® Technology WARNING FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist. The maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in property damage, personal injury, or death. Improper installation and/ or operation may void the warranty. ATTENTION INSTALLER - This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment. H0644400 REV D Page 2 ENGLISH Jandy® TruGuardTM | Installation & Operation Manual Table of Contents Section 1. Important Safety Instructions ....... 3 Section 2. General Description ...................... 4 2.1 Product Overview ..........................................................4 2.2 Product Contents...........................................................4 Section 3. Installation Requirements ............ 4 Section 4. Installing the Jandy TruGuard ..... 5 Section 5. Cartridge Replacement ................... 7 Section 6. Winterizing ...................................... 8 6.1 Warm Climate................................................................8 6.2 Cold Climate..................................................................8 Section 7. Disposal ........................................... 9 Jandy® TruGuardTM | Installation & Operation Manual ENGLISH Page 3 Section 1. Important Safety Instructions READ AND FOLLOW ALL INSTRUCTIONS The Jandy TruGuard pool sanitizer is designed only for residential swimming pools. When installing and using this equipment, basic safety precautions should always be followed, including the following: WARNING EQUIPMENT UNDER PRESSURE · Always turn pump off prior to installing or changing Nature2 cartridge. Your pump/filter system is operated under pressure and the pressure must be released before you begin work. Please see your pump/filter owner's manual for further instructions. PREVENT CHILD DROWNING · Do not let anyone, especially small children, sit, step, lean or climb on any equipment installed as part of your pool's operational system. Locate the components of your operational system at least 3 feet from the pool so children cannot use the equipment to access the pool and be injured or drown. LOW CHLORINE RECIPE · You must strictly follow the low chlorine recipe included in this manual to maintain proper water chemistry and avoid health hazards. Failure to follow these instructions can lead to sickness from bacteria and other noxious organisms. CAUTION PRECAUTIONARY STATEMENT HAZARDS TO HUMANS AND DOMESTIC ANIMALS In the unlikely event that a cartridge breaks, mineral media should not be ingested by humans or animals as it may cause gastric distress. FIRST AID IF INGESTED: Call poison control center or doctor immediately for treatment advice. ATTENTION INSTALLER This manual contains important information about the installation, operation and safe use of this product. This information should be given to the owner/operator of this equipment. SAVE THESE INSTRUCTIONS Page 4 ENGLISH Jandy® TruGuardTM | Installation & Operation Manual Section 2. General Description 2.1 Product Overview This manual provides instructions for installing and replacing the Jandy TruGuard to sanitize swimming pools from 5,000 to 45,000 gallons. The TruGuard housing will fit on 2" or 2 1/2" pipe sizes. The Jandy TruGuard consists of Nature2® technology used in conjunction with a chlorine delivery device or 0.5 ppm of an EPA registered chlorine pool product. Nature2 technology consists of silver and copper minerals. Every pool has it's own characteristics of water type and exposure to natural elements. The recipe included in this manual will help ensure good water quality for your pool that will make your swimming experience more enjoyable. NOTICE This product is not compatible with biguanide products or copper based algaecide and should not be used in any manner inconsistent with the product manuals and labeling. 2.2 Product Contents 2 1 3 4 5 1 - TruGuard Housing 2 - TruGuard Cartridge 3 - Winterizing and Pressurizing Cap 4 - Owner's Manual 5 - Installation Manual Section 3. Installation Requirements Before installing a new TruGuard cartridge, clean debris and algae out of the pool and pool equipment. Do not install the new cartridge until the pool water is clean and chemically balanced. Refer to the Owner's Manual for water balance instructions. Jandy® TruGuardTM | Installation & Operation Manual ENGLISH Page 5 Section 4. Installing the Jandy TruGuard The Jandy TruGuard installs on your pool's return line. 1. Determine the location to install the Jandy TruGuard. It must be installed: · After the filter on the main return to the pool. · Before or after the heater (downstream of solar heating systems). · Before check valve to any chemical dispenser or the discharge of any off-line chemical dispenser. Check Valve Filter Heater Chlorinator TRUGUARD 2. Locate an area on the return line that is at least 8" to install the Jandy TruGuard. 3. Turn OFF the pool pump. Your pump/filter system is operated under pressure. The pressure must be released before you begin work. Please refer to the pump/filter owner's manual for further instructions. Page 6 ENGLISH Jandy® TruGuardTM | Installation & Operation Manual 4. Close any valves. If your pool filtration equipment is below the water level of the pool, you will either need to close the return valve or use winterizing plugs at the skimmer and return fittings to prevent excessive water loss. 5. Remove the cartridge from the housing and plumb the housing into the pipe, making sure that the flow indicator arrows on the housing match the flow direction of the water. Pipes must be clean and dry before gluing. NOTE: If the flow direction of the water does not match the arrows on the housing, the unit will not function properly. Housing can be oriented horizontally or vertically. For ease of servicing and maintenance, it is recommended that the housing be installed horizontally with the cartridge facing up. Water Flow 6. Insert the TruGuard cartridge into the housing. Water Flow Jandy® TruGuardTM | Installation & Operation Manual 7. Tighten the locking ring. ENGLISH Page 7 8. Write the installation date and replacement date on the cartridge label. 9. Open any valves that you closed, and turn on your pool pump to verify that there are no leaks. If there is a leak, turn off the pump, close the valves, and remove the TruGuard. Check that the o-ring is not pinched and is seated properly. Replace the cartridge and hand tighten the nut. 10. Superoxidize the pool water with chlorine according to manufacturer's instructions to burn off contaminants and activate cartridge. IMPORTANT: Initial superoxidation with chlorine is required to burn off contaminants and activate cartridge. 11. Run the circulating pump for 24 hours a day for 4 days, maintaining 1-2 ppm free chlorine throughout, or 6 hours a day for 14 days, maintaining 1-2 ppm free chlorine throughout. 12. Let chlorine dissipate to 0.5 ppm once start up period is completed. Do not enter the pool if the free available chlorine residual is over 3 ppm. 13. Refer to Owner's Manual for maintaining a low chlorine recipe. Section 5. Cartridge Replacement The TruGuard cartridge needs to be replaced every six months. The installation and replacement date of the cartirdge should be written on the cartridge label when installed. 1. Turn off the pool pump. 2. Release the pressure from your pool plumbing system. Refer to your pump/filter manual for pressure release instructions. Page 8 ENGLISH Jandy® TruGuardTM | Installation & Operation Manual 3. Close any valves. If your pool filtration equipment is below the water level of the pool, you will either need to close the return valve or use winterizing plugs at the skimmer and return fittings to prevent excessive water loss. 4. Loosen the locking ring. 5. Remove the old TruGuard cartridge. 6. Install the new TruGuard cartridge. 7. Write the installation date and replacement date on the cartridge label. 8. Tighten the locking ring. 9. Follow the instructions on running the circulating pump and maintaining free chlorine levels as outlined in Section 4 "Installing the Jandy TruGuard" section above. Section 6. Winterizing 6.1 Warm Climate 1. Reduce the number of hours that the pump runs since the cooler weather decreases the spread of algae and other pollutants. 2. There is no need to superoxidize the pool during cool weather unless the water becomes cloudy (as may occur after a winter storm). See cloudy water in Troubleshooting section. 6.2 Cold Climate 1. Check total alkalinity and pH of pool to make sure that they are in proper balance. 2. Vacuum the pool bottom to remove any debris or other potential contaminants. 3. Superoxidize the pool with chlorine according to manufacturer's instructions to clear the water. 4. Add a winter algaecide following manufacturer's instructions. IMPORTANT: Do not use a winter algaecide with copper in it. This will void the Jandy warranty. 5. Backwash the filter. 6. Drain part of the pool water. The amount to drain varies from one part of the country to another. Consult your dealer for advice. 7. Remove the TruGuard cartridge and discard. Jandy® TruGuardTM | Installation & Operation Manual ENGLISH Page 9 8. Place the Winterizing and Pressurizing Cap in the housing and tighten the locking ring. 9. Winterize the pipes with pool antifreeze following manufacturer's instructions. 10. Drain the water out of all equipment (pump, filter, etc.). 11. Store all baskets, hoses and cleaning equipment, indoors if possible. 12. Cover the pool with a winter cover. Section 7. Disposal After six months of use, discard the TruGuard cartridge in household trash. Do not save the cartridge for re-use. The cartridge contains mineral media that is sealed inside. In the unlikely event that a cartridge breaks, remove it and vacuum out any media introduced into the pool. Zodiac Pool Systems LLC 2882 Whiptail Loop # 100 Carlsbad, CA 92010 1.800.822.7933 | www.ZodiacPoolSystems.com ©2021 Zodiac Pool Systems LLC. All rights reserved. ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license. All other trademarks are the property of their respective owners. H0644400 REV D ETL LISTED CONFORMS TO UL STD 676 CERTIFIED TO CAN/CSA C22.2 NO.89 MANUAL DE INSTALACIÓN Y OPERACIÓN ESPAÑOL Jandy TruGuardTM con tecnología Nature2® ADVERTENCIA PARA SU SEGURIDAD: la instalación y el servicio técnico de este producto deben estar a cargo de un contratista cualificado y matriculado para trabajar con equipamientos para piscinas en la jurisdicción en la que se instalará el producto, donde existan tales requisitos estatales o locales. El técnico de servicio debe ser profesional y contar con experiencia suficiente en instalación y mantenimiento de equipamientos para piscinas, para que todas las instrucciones de este manual se puedan seguir exactamente. Antes de instalar este producto, lea y siga todos los avisos de advertencia y las instrucciones que se proporcionan con el producto. Si no se siguen los avisos de advertencia ni las instrucciones, es posible que se produzcan daños materiales, lesiones personales o la muerte. Una instalación u operación incorrectas pueden anular la garantía. ATENCIÓN, INSTALADOR: este manual contiene información importante acerca de la instalación, la operación y la utilización seguras de este producto. Esta información debe ser entregada al dueño u operador de este equipo. H0644400 REV D Página 14 ESPAÑOL Jandy® TruGuardTM | Manual de instalación y operación Contenido Sección 1. Instrucciones importantes de seguridad...................................... 15 Sección 2. Descripción general .................... 16 2.1 Aspectos generales del producto ................................16 2.2 Contenido del producto ...............................................16 Sección 3. Requisitos de instalación ........... 16 Sección 4. Cómo instalar el Jandy TruGuard .......................... 17 Sección 5. Reemplazo del cartucho ............. 20 Sección 6. Preparación para el invierno....... 20 6.1 Clima cálido.................................................................20 6.2 Clima frío .....................................................................20 Sección 7. Eliminación................................... 21 Jandy® TruGuardTM | Manual de instalación y operación ESPAÑOL Página 15 Sección 1. Instrucciones importantes de seguridad LEA Y SIGA ESTAS INSTRUCCIONES El sanitizador para piscinas Jandy TruGuard está diseñado únicamente para piscinas residenciales. Cuando se instale y utilice este equipo, siempre se deberán seguir las siguientes precauciones básicas de seguridad: ADVERTENCIA EQUIPO BAJO PRESIÓN · Siempre apague la bomba antes de instalar o cambiar un cartucho Nature2. El sistema de bomba/filtro funciona bajo presión y la presión debe liberarse antes de comenzar a trabajar. Consulte el manual del usuario de la bomba o del filtro para obtener instrucciones adicionales. EVITE EL AHOGAMIENTO DE LOS NIÑOS · No permita que ninguna persona, especialmente niños pequeños, se siente, pise, se apoye o trepe en los equipos instalados como parte del sistema de operación de la piscina. Ubique los componentes del sistema operativo al menos a 3 pies de la piscina de tal forma que los niños no puedan usar el equipo para acceder a la piscina y se lesionen o se ahoguen. FÓRMULA CON BAJO CLORO · Debe seguir estrictamente la fórmula con bajo cloro incluida en este manual para mantener una química del agua correcta y evitar peligros para la salud. Si no se cumplen estas instrucciones, pueden producirse enfermedades por bacterias y otros organismos nocivos. PRECAUCIÓN INDICACIÓN DE PRECAUCIÓN PELIGROS PARA LOS HUMANOS Y PARA LOS ANIMALES DOMÉSTICOS En el caso improbable que se rompa un cartucho, los humanos o los animales no deben ingerir el material mineral, ya que puede provocar problemas gástricos. PRIMEROS AUXILIOS SI SE INGIERE: Llame a un centro de toxicología o a un médico de inmediato para obtener asesoramiento sobre el tratamiento. ATENCIÓN, INSTALADOR Este manual contiene información importante acerca de la instalación, la operación y la utilización seguras de este producto. Esta información debe proporcionarse al propietario/operador de este equipo. GUARDE ESTAS INSTRUCCIONES Página 16 ESPAÑOL Jandy® TruGuardTM | Manual de instalación y operación Sección 2. Descripción general 2.1 Aspectos generales del producto Este manual proporciona instrucciones para instalar y reemplazar el Jandy TruGuard para sanitizar piscinas de 5000 a 45 000 galones. El alojamiento del TruGuard cabe en tubos de 2" o 2 1/2" de tamaño. El Jandy TruGuard consiste en la tecnología Nature2® utilizada en conjunto con un dispositivo de suministro de cloro o 0.5 ppm de un producto de cloro para piscinas registrado con la EPA. La tecnología Nature2 consiste en minerales de plata y cobre. Cada piscina tiene sus propias características de tipo de agua y exposición a los elementos naturales. La fórmula que se incluye en este manual ayudará a asegurar una buena calidad del agua para su piscina, a fin de que disfrute más su experiencia en la piscina. AVISO Este producto no es compatible con los productos de biguanida ni con los alguicidas a base de cobre y no debe utilizarse de forma incompatible con los manuales y el etiquetado del producto. 2.2 Contenido del producto 2 1 3 4 5 1 - Alojamiento de TruGuard 2 - Cartucho de TruGuard 3 - Tapa para el invierno y para presurización 4 - Manual del propietario 5 - Manual de instalación Sección 3. Requisitos de instalación Antes de instalar un nuevo cartucho TruGuard, limpie los residuos y las algas de la piscina y de los equipos de la piscina. No instale el nuevo cartucho hasta que el agua de la piscina esté limpia y equilibrada químicamente. Consulte el manual del propietario para obtener las instrucciones sobre cómo equilibrar el agua. Jandy® TruGuardTM | Manual de instalación y operación ESPAÑOL Página 17 Sección 4. Cómo instalar el Jandy TruGuard El Jandy TruGuard se instala en la línea de retorno de la piscina. 1. Determine la ubicación para instalar el Jandy TruGuard. Debe instalarse: · Después del filtro en el retorno principal a la piscina. · Antes o después del calentador (aguas abajo de los sistemas solares de calentamiento). · Antes de la válvula de retención para cualquier dispensador químico o la descarga de cualquier dispensador químico fuera de la línea. válvula de retención filtro TRUGUARD calentador Sistema generador de cloro 2. Ubique un área en la línea de retorno que tenga al menos 8" para instalar el Jandy TruGuard. 3. APAGUE la bomba de la piscina. El sistema de bomba/filtro funciona bajo presión. La presión debe liberarse antes de comenzar el trabajo. Consulte el manual del usuario de la bomba/ del filtro para obtener instrucciones adicionales. Página 18 ESPAÑOL Jandy® TruGuardTM | Manual de instalación y operación 4. Cierre todas las válvulas. Si el equipo de filtrado de la piscina está por abajo del nivel del agua de la piscina, deberá cerrar la válvula de retorno o usar tapones para el invierno en el filtro superficial y acoples de retorno para evitar la pérdida excesiva de agua. 5. Quite el cartucho del alojamiento y conecte el alojamiento al tubo, asegurándose de que las flechas del indicador de flujo del alojamiento coincidan con la dirección de flujo del agua. Los tubos deben estar limpios y secos antes de adherirlos. NOTA: Si la dirección del flujo de agua no coincide con las flechas del alojamiento, la unidad no funcionará correctamente. El alojamiento puede orientarse horizontal o verticalmente. Para facilidad de servicio y mantenimiento, se recomienda que el alojamiento se instale horizontalmente con el cartucho mirando hacia arriba. Water Flow 6. Inserte el cartucho TruGuard en el alojamiento. Water Flow Jandy® TruGuardTM | Manual de instalación y operación 7. Apriete el anillo de bloqueo. ESPAÑOL Página 19 8. Escriba la fecha de instalación y la fecha de reemplazo en la etiqueta del cartucho. 9. Abra las válvulas que haya cerrado y encienda la bomba de la piscina para verificar que no haya fugas. Si hay alguna fuga, apague la bomba, cierre las válvulas y extraiga el TruGuard. Verifique que la junta tórica no esté pellizcada y que esté asentada correctamente. Vuelva a colocar el cartucho y apriete la tuerca con la mano. 10. Superoxide el agua de la piscina con cloro según las instrucciones del producto para quemar los contaminantes y activar el cartucho. IMPORTANTE: La superoxidación inicial con cloro es necesaria para quemar contaminantes y activar el cartucho. 11. Haga funcionar la bomba de circulación durante las 24 horas durante 4 días, manteniendo siempre cloro libre a 1-2 ppm, o durante 6 horas por día durante 14 días, manteniendo siempre cloro libre a 1-2 ppm. 12. Permita que el cloro se disipe a 0.5 ppm después de finalizado el periodo de puesta en funcionamiento. No ingrese a la piscina si el cloro libre disponible residual está por arriba de 3 ppm. 13. Consulte el manual del propietario para mantener una fórmula con bajo cloro. Página 20 ESPAÑOL Jandy® TruGuardTM | Manual de instalación y operación Sección 5. Reemplazo del cartucho El cartucho TruGuard debe reemplazarse cada seis meses. Las fechas de instalación y de reemplazo del cartucho deben escribirse en la etiqueta del cartucho cuando se instala. 1. Apague la bomba de la piscina. 2. Libere la presión del sistema de tuberías de la piscina. Consulte el manual de la bomba/del filtro para obtener las instrucciones sobre cómo liberar la presión. 3. Cierre todas las válvulas. Si el equipo de filtrado de la piscina está por abajo del nivel del agua de la piscina, deberá cerrar la válvula de retorno o usar tapones para el invierno en el filtro superficial y acoples de retorno para evitar la pérdida excesiva de agua. 4. Afloje el anillo de bloqueo. 5. Extraiga el cartucho TruGuard anterior. 6. Instale el nuevo cartucho TruGuard. 7. Escriba la fecha de instalación y la fecha de reemplazo en la etiqueta del cartucho. 8. Apriete el anillo de bloqueo. 9. Siga las instrucciones sobre el funcionamiento de la bomba de circulación y el mantenimiento de los niveles de cloro libre como se indica en la sección 4 "Instalación del Jandy TruGuard". Sección 6. Preparación para el invierno 6.1 Clima cálido 1. Reduzca la cantidad de horas que funciona la bomba, debido a que el clima más frío reduce la propagación de algas y otros contaminantes. 2. No hay necesidad de superoxidar la piscina durante el clima frío, a no ser que el agua se ponga turbia (como puede suceder después de una tormenta de invierno). Consulte el apartado sobre el agua turbia en la sección de resolución de problemas. 6.2 Clima frío 1. Verifique la alcalinidad total y el pH de la piscina para asegurarse de que estén en el equilibrio correcto. Jandy® TruGuardTM | Manual de instalación y operación ESPAÑOL Página 21 2. Aspire el fondo de la piscina para eliminar cualquier residuo u otros contaminantes potenciales. 3. Superoxide la piscina con cloro según las instrucciones del producto para limpiar el agua. 4. Agregue un alguicida de invierno según las instrucciones del producto. IMPORTANTE: No utilice ningún alguicida de invierno que contenga cobre. Esto anulará la garantía de Jandy. 5. Retrolave el filtro. 6. Drene parte del agua de la piscina. La cantidad que debe drenarse depende del lugar del país donde esté. Consulte a su distribuidor para obtener asesoramiento. 7. Extraiga el cartucho TruGuard y elimínelo. 8. Coloque la tapa para el invierno y para presurización en el alojamiento y apriete el anillo de bloqueo. 9. Prepare los tubos para el invierno con anticongelante para piscinas. Siga las instrucciones del producto. 10. Drene el agua de todos los equipos (bomba, filtro, etc.). 11. Guarde todos los canastos, mangueras y equipos de limpieza, si es posible bajo techo. 12. Cubra la piscina con un cobertor para invierno. Sección 7. Eliminación Después de seis meses de uso, elimine el cartucho TruGuard con los residuos domésticos. No guarde el cartucho para volver a utilizarlo. El cartucho contiene un material mineral sellado dentro. En el caso improbable de que se rompa un cartucho, quítelo y aspire cualquier material que se haya introducido en la piscina. Zodiac Pool Systems LLC 2882 Whiptail Loop # 100 Carlsbad, CA 92010 1.800.822.7933 | www.ZodiacPoolSystems.com ©2021 Zodiac Pool Systems LLC. Todos los derechos reservados. ZODIAC® es una marca registrada de Zodiac International, S.A.S.U. y se utiliza bajo licencia. Todas las demás marcas comerciales son propiedad de sus respectivos dueños. H0644400 REV D INCLUIDO EN ETL CUMPLE UL STD 676 CERTIFICACIÓN CAN/CSA C22.2 NO.89Adobe PDF Library 16.0 Adobe InDesign 16.4 (Windows)