User Manual

1. Feature

• This unit is a 4-channel distributor for the layer 1 POWER, available for a maximum of three units (within 30 meters).
• This unit can be used by connecting with the 2-wire loop type Interphone (e.g., AP-2SAG) manufactured by COMMAX.
• This unit can also be used by connecting with a Phone with keypad.
• Remote updating is possible by guard phone.
• Please make sure to check the wire sequence.
• Avoid duplication of other devices' ID.
• This unit requires a Power of DC24V/3A (Recommended RF-24AS by COMMAX).

2. Warnings and Caution

Please follow the instructions below to prevent any danger or property damage.

Warning: It may cause serious damage or injury if violated.

Caution: It may cause minor damage or injury if violated.

Prohibitions:

• No disassembly
• No touch
• Must follow strictly.
• Shows plugging out the power cord without exception.
• Shows the warning and caution for electric shock.
• Shows the warning and caution for fire.

Power & Installation Warnings:

• Do not use several products at the same time on one power socket.
  It may cause a fire due to abnormal overheating. [Fire Symbol]
• Do not bend the power cable excessively.
  It may cause an electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• Do not handle the power cable with a wet hand.
  It may cause an electric shock. [Electric Shock Symbol]
• Plug out the power cable from the socket when not using it for a long period of time.
  It may shorten the product lifespan or cause a fire. [Fire Symbol]
• Do not install the product in a place with much oil, smoke, or humidity.
  It may cause an electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• Do not install the product during lightning and thunder.
  It may cause an electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• Do not use and connect this product with other products with different rated voltage.
  It may cause a disorder or fire. [Fire Symbol]
• When installing the product that generates heat, install it away from the wall (10cm) for ventilation.
  It may cause a fire due to increased internal temperature. [Fire Symbol]

Cleaning & Use Warnings:

• Do not disassemble, repair, or rebuild this product arbitrarily. Contact the service center if repair is needed. It may cause an electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• If an abnormal sound, burning smell, or smoke is coming out of the product, plug out the power cable and contact a service center. It may cause an electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• Do not insert any metallic or burnable materials into the ventilation hole. It may cause an electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• Use only the designated batteries for products using DC power. It may cause an electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• Plug the power cable firmly into the inner end. It may cause a fire. [Fire Symbol]
• Hold the plug tightly when unplugging the power cable. Pulling only the cord may disconnect the copper wire, causing electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• When connecting power cables after cutting, install the product with the power off. It may cause an electric shock or fire. [Electric Shock Symbol] [Fire Symbol]
• When installing the product, fix it firmly using the wall-mounting unit and screws. It may cause injury from falling objects. [Injury Symbol]
• Be careful when using an AC circuit breaker, as there is a possibility of electric shock. [Electric Shock Symbol]
• Check the voltage and current for DC-only products and use the appropriate rectifier. It may cause a fire. [Fire Symbol]
• When cleaning the product, use a soft and dry cloth after unplugging the power cable. Do not use chemical products like wax, benzene, alcohol, or cleanser. [Cleaning Symbol]
• Do not drop the product on the ground or apply shock. It may cause failure. [Failure Symbol]
• Avoid direct sunlight or heating devices during installation. It may cause a fire. [Fire Symbol]
• Do not install the product on an unstable place or small support board. It may cause injury if it falls. [Injury Symbol]
• Use the designated connection cable within the maximum calling distance. Using a cable beyond this distance may reduce product performance. [Performance Symbol]

3. The name & Function

3-1. Diagram & Table Name

A diagram shows the layout of the unit with numbered components. A table lists these components:

3-2. FUNCTION

• Common line output terminal: Distributor Common line output terminal.
• Common line input terminal: Lobby Common line & Distributor common line input terminal.
• Household input & output terminal: Household call line input terminal.
• Program terminal: Terminal for program download.
• RS-232 Connection terminal: Used to change settings via a PC.
• Power switch: ON/OFF switch for power.
• Power input terminal: RF-24AS Adaptor connection terminal.
• Status LED: LED indicates the status.
  • Power LED: On when power is on.
  • Lobby call LED: On when calling between HOUSEHOLD & LOBBY.
  • Guard call LED: On when calling between Household & Guard or Household.
  • Data LED: On when transferring data between devices.
  • Error check LED: On when there is an error.
• ID SWITCH: DIP SWITCH used to set the ID.

4. Manual to use

4-1. Door open function of the Lobby (Control function of household interphone)

To open the door with the interphone while talking to the Lobby phone:

4-1-1: Method using the Hook switch

1. Press and release the hook switch for 1 second.
2. The door opens.
3. Press the handset down to end the call. (Caution: Guard room is called if you do not hang up within a period.)

4-1-2: Method using the door open button

1. Press the door open button while talking to the lobby.
2. The door opens.
3. Press the handset down to end the call.

4-2. When changed by the guard phone:

Refer to the user manual of the linkage guard phone.

4-3 The Method to set the device ID

Set the device ID using BCD code via the DIP switch. The DIP switch is divided into two parts: Lower 4 bits (1-4) and Upper 4 bits (5-8).

A visual representation of the DIP switch settings for numbers 0-9 is provided, showing how to set the lower bits (unit's place) and upper bits (ten's place) to achieve IDs up to 99.

5. System Diagram

A system diagram illustrates the connections between Household units, Floor Distributor, Guard Station, Lobby Phone, and Adapter. It shows power connections (12V, 24V) and data flow.

6. Wiring

Wiring instructions are provided for connecting Household Units (ROOM1-ROOM4) to the main unit via IN and OUT ports. Connections for the Lobby Phone or Floor Distributor are also detailed:

• Lobby Phone: Connection 1-6 Pin
• Floor Distr.: Connection 1-8 Pin

The diagram shows connections to DIP SW, PROGRAM, RS-232, and POWER SW (ON/OFF) with an RF-24AS connection.

7. Precautions.

• If the product is damaged or an error occurs, contact customer support at the head office.
• Do not place flower vases or bottles on the product.
• A proper cutoff (device can cut all) must be used for indoor wiring. In case of fire or equipment malfunction, press the building's breaker as soon as possible.
• Turn off the power before installing or repairing the product.

8. Others

• Before reporting faulty equipment, read the manual thoroughly.
• Check all statuses before making a customer service call.

9. Specifications and Characteristics