Instructions for ROLANSTAR models including: Height Adjustable Desk, CPT007-YW120-RR, CPT007-BK120-RR, CPT007-BO120-RR
OPERATION INSTRUCTIONS Up / Down Button Press the ∧ to raise the desk, when you release the button it will stop. Press the ∨ to lower the desk, when you release the button it will stop. When pressing the ∧ / ∨, the desk travels a very short distance, so that users can fine-tune the desk height according to preference.
File Info : application/pdf, 21 Pages, 4.18MB
DocumentDocumentHEIGHT ADJUSTABLE DESK CPT007-YW120-RR CPT007-BK120-RR CPT007-BO120-RR V12.0 cs@rolanstar.com 1 2 3 4 1 x2 ACCESSORIES LIST 2 x2 3 x1 4 x2 5 x2 6 x2 7-L x1 7-R x1 8 x1 9 x1 10 x1 11 x1 12 x1 120cm / 47.2in 55cm / 21.7in 15 x1 13 x1 14-L x1 20cm / 7.9in 120cm / 47.2in 16 x1 17 x1 14-R x1 8cm / 3.1in 8.8cm / 3.5in 60cm / 23.6in 56cm / 22in 25.7cm / 10.1in 53cm / 20.9in 5 A x12+1 B x8+1 C x14+1 D x10+1 M8*10mm E x8+1 M8*35mm F x4 ST4.8*12mm G x4 1/4*12mm H x4 1/4*25mm I x5 J x4 5*35mm K x4 13*25mm L x12+2 M x1 N x1 O x1 K4 K5 6 EXPLODED 6 4 1 13 6 12 3 8 x1 9 x1 5 4 10 1 2 2 7-L 14-L 16 14-R 7-R 17 15 7 STEP 1 3 1 1 A X8 N X1 K5 A A A A 8 STEP 2 A X4 N X1 K5 A 4 A 4 STEP 3 B X 8 J X4 K K J 2 X4 N X1 K5 B K J 9 STEP 4 D X6 M X1 K4 D D D D D D 12 STEP 5 C X14 98 10 10 C 5 STEP 6 G X4 Do not fully tighten the screws yet G 14-L ×1 G 16 14-R Note Grooves downward 17 11 STEP 7 F X4 F 15 Do not fully tighten the screws yet F 15 Tighten the screws 12 STEP 8 7-L Fully tighten all the screws Note This part upward 14-R Note Push part 7 into part 14 COMPLETE 13 STEP 9 D X4 M X1 D D 12 L X4 Put Part L between Part 7 and 12 before screwing if the contact surface is uneven 14 7-R L STEP 10 11 Plug In 15 STEP 11 I X5 STICK 16 TIGHTEN STEP 12 E X8 H 4 X M K4 X1 L X8 Fully tighten all the screws H H E 5.8cm / 2.3in 3.4cm / 1.3in L 13 E E 17 STEP 13 K Adjust K to make the desk steady 18 OPERATION INSTRUCTIONS Up / Down Button Press the to raise the desk, when you release the button it will stop. Press the to lower the desk, when you release the button it will stop. When pressing the / , the desk travels a very short distance, so that users can fine-tune the desk height according to preference. Desktop Height Memory Setting POSITION SETTING: Can set up two memories. Adjust the desktop to the appropriate height with or buttons. And then press "1 or 2" button, about 4 seconds until the display flashes "S -1 or S-2 ", indicating that memory setting is successful. LOCATION QUERY: In the run mode, press any of the 1 / 2 keys to flash the height of the key memory. POSITION REACHING: In the run mode, when the desktop stops, press any of the 1 / 2 keys twice to adjust to the desktop height of the key memory. When desktop is moving, pressing any button can stop it. The Lowest Height Position Setting POSITION SETTING: Please adjust the desktop to the appropriate height; and then hold both "2" and "" button for 5 seconds; when the display appears "- d o", the lowest height is memorized successfully. Once the desktop is dropped to its lowest height position, the display shows "- L o". POSITION CANCELLATION: Option 1 - Refer to the initial setting process. Option 2 - Adjust the desktop to the lowest height where the display shows "- L o", hold both "2" and the down button for 5 seconds; at this time, the display will show "- d o" indicating the set lowest height position has been successfully canceled. The Highest Height Position Setting POSITION SETTING: Please adjust the desktop to the appropriate height; and then hold both "1" and the up button for 5 seconds; when the display appears "- u p", the highest height is memorized successfully. Once the desktop is raised to its highest height position, the display shows "- h I". POSITION CANCELLATION: Option 1 - Refer to the initial setting process. Option 2 - Adjust the desktop to the highest height where the display shows "- h I", hold both "1" and the up button for 5 seconds; at this time, the display will show "- u p" indicating the set highest height position has been successfully canceled.. Initial Settings cUnder normal state, can be operated at any time; Or replace the controller for the first time Press and hold both the and until the display appears " - - - ", release the keys, then the tabletop will automatically move up and down. When the top stop moving, the initial setting process succeeds. Restore Factory Settings When the display appears error code "rST" or "E16", press and hold the "V" button for 5 seconds until the display flashes " - - - "; release the key, then the adjustable desk legs will automatically move down to its mechanical lowest point, and move up and stop at a factory-preset position. Finally, the desk can work normally. 19 AUTOMATED EXERCISE REMINDER Once the desktop stays at a same height position over 45 mins, the display shows "Chr". The flash of "Chr"will disappears when you press any of button or after 1 minute without any operation. The reminder will work for 3 times in a row. COMMON ERROR CODE (PROBLEM DESCRIPTION AND SOLUTION) E01aE02 Cable Connection Between Desk Leg(s) And Control Box is Loose (press the up or down button; if it doesn't work, please check the cable connection) E03aE04 Desk Leg(s) is Overloaded (press the up or down button; if it doesn't work, reduce desk load or contact seller) E05aE06 Sensing Element in the Desk Leg(s) Fails (press the up or down button; if it doesn't work, please check cable connection or contact seller) Control Box Breaks Down E07 (cut off the power supply for a while and restart the desk; if it doesn't work, please contact seller) E08aE09 Desk Leg(s) Breaks Down (cut off the power supply for a while and restart the desk; if it doesn't work, please contact seller) E10aE11 Controller Components Breaks Down (cut off the power supply for a while and restart the desk; if it doesn't work, please contact seller)t E12 Desk Leg(s) Malposition(refer to the initial setting process) E13 Thermal Shutdown Protection (wait for temperature drop) E14aE15 Desk leg(s) is Stuck, and or They Do Not Work Properly (press the up or down button; if it doesn't work, reduce desk load or contact seller) E16 Unbalance Desktop (restore factory settings) E17 Key Data Stored in Control Box are Lost (please contact seller directly) rST Abnormal Power-Down (check the cable connection then restore factory settings) 20Adobe Illustrator 24.0 (Macintosh) 3-Heights™ PDF Optimization Shell 6.3.1.5 (http://www -tools.com)
