ENVOY™ Installation Instructions

Product Overview

This document provides installation instructions for the Human Active Technology ENVOY-1 articulating monitor arm. It is designed to securely hold monitors and provide flexible positioning.

Safety and Warnings

• Please read the entire instruction manual before starting installation and assembly. If you have any questions, contact your local distributor.
• ⚠️ CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
• Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• ❗ IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your local distributor for a replacement.

Specifications

Parts List

Components:

• A: Main Arm (x1)
• B: Desk Clamp Base (x1)
• C: Clamp Arm Bracket (x1)
• D: Desk Clamp Pole (x1)
• E: Grommet Mount Base (x1)
• F: VESA Plate (x1)
• G: VESA Plate Bracket (x1)
• H: Pole Cap (x1)
• P: Monitor Support Arm (x1)

Hardware:

• J: M6x10 Screws (x5)
• K: M6x12 Screws (x4)
• L: 4mm Allen Wrench (x1)
• M: 6mm Allen Wrench (x1)
• N: M4x12 Screws (x4) - for VESA plate to monitor
• O: M5x12 Screws (x4) - for VESA plate to monitor
• D5: Washers (x4) - for VESA plate to monitor

Assembly Instructions

Follow these steps carefully for proper installation. Refer to the diagrams for visual guidance.

1. Step 1a-1: Attach Clamp Arm Bracket to Main Arm

   Connect the Clamp Arm Bracket (C) to the Main Arm (A) using five M6x10 screws (J). Ensure the bracket is oriented correctly as shown in the diagram.

2. Step 1a-2a: Attach Main Arm to Desk Clamp (Clamp Method)

   Insert the Main Arm assembly (A+C) into the Desk Clamp Pole (D). Secure it using two M6x12 screws (K) and the 6mm Allen Wrench (M). Ensure the arm is positioned correctly for desk clamping.

3. Step 1a-2b: Attach Main Arm to Desk Clamp (Grommet Method)

   Insert the Main Arm assembly (A+C) into the Grommet Mount Base (E). Secure it using two M6x12 screws (K) and the 6mm Allen Wrench (M). This method is for desks with a pre-drilled grommet hole.

4. Step 1a-3: Attach VESA Plate Bracket to Monitor Support Arm

   Connect the VESA Plate Bracket (G) to the Monitor Support Arm (P). The diagram indicates this connection is made at the end of the Monitor Support Arm.

5. Step 1a-4: Final Arm Assembly

   Connect the main arm assembly (A+C+D/E) to the monitor support arm assembly (P+G). This typically involves sliding the main arm pole into the monitor support arm mechanism and securing it.

6. Step 1b-1: Alternative Desk Clamp Attachment

   This illustrates an alternative configuration for attaching the main arm to the desk clamp base (B) using the Desk Clamp Pole (D) and screws (K).

7. Step 1b-2: Alternative Grommet Mount Attachment

   This illustrates an alternative configuration for attaching the main arm to the grommet mount base (E) using screws (K).

8. Step 2: Attach VESA Plate to Monitor

   Select the appropriate screws (N: M4x12 or O: M5x12) and washers (D5) based on your monitor's VESA mounting holes. Attach the VESA Plate (F) to the back of your monitor. Use the 4mm Allen Wrench (L) or a screwdriver as needed.

9. Step 3: Mount Monitor onto Arm

   Carefully lift the monitor with the attached VESA plate and align it with the VESA Plate Bracket (G) on the monitor arm. Slide the VESA plate onto the bracket and secure it using the locking mechanism (indicated by ① in the diagram, often a quick-release or locking screw).

Diagram Descriptions from Page 1:

• The primary product image shows the ENVOY monitor arm mounted to a desk, holding a monitor. It highlights the arm's articulation and reach.
• Additional small diagrams illustrate the range of motion: 180° rotation, 360° swivel, +90°/-90° tilt, and 180° pivot.

Maintenance

⚙️ Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Contact Information

Human Active Technology

Phone: 800 524 2744

Email: customerservice@team-hat.com

Website: team-hat.com