Features / Cechy
- 1 Left Side Panel / Lewy panel boczny
- 2 PSU Dust Filter / Filtr przeciwkurzowy pod zasilaczem
- 3 Toolless Retention Bracket / Beznarzędziowe mocowanie kart rozszerzeń
- 4 Top Dust Filter / Górny filtr przeciwkurzowy
- 5 SSD Tray / Tacka na SSD
- 6 Right Side Panel / Prawy panel boczny
- 7 HDD/SSD cage / Koszyk na HDD/SSD
Accessory Kit / Elementy montażowe
- 14x Motherboard screws / Śruby płyty głównej
- 8x HDD screws / Śruby dysku twardego
- 8x PSU screws / Śruby zasilacza
- 3x Standoffs / Dystanse
- 5x Cable ties / Opaski zaciskowe
- 8x Screws for installing fans on the PSU shroud / Śruby do montażu wentylatorów na tunelu zasilacza
Panel I/O / Panel We/Wy
- 1 Power / włącznik
- 2 Reset
- 3 USB 3.0
- 4 Headphones+Microphone / Słuchawki+Mikrofon
- 5 USB 3.0
- 6 USB Type-C / USB Typ-C
Specification / Specyfikacja
PC Case Dimensions: 385 mm (L) x 200 mm (W) x 456 mm (H)
GPU Max Length: 340 mm
CPU Max Height: 155 mm
PSU Max Length: 200 mm (with HDD tray) / 300 mm (without HDD tray)
Fan Support:
- Front: 2 x 120 mm (or max 2 x 140 mm)
- Rear: 1 x 120 mm (pre-installed)
- Top: 3 x 120 mm (or max 3 x 140 mm)
- Bottom: 2 x 120 mm
Radiator Support: 120 mm / 240 mm / 280 mm / 360 mm (Top)
Note: Installing 3 x 140 mm fans at the front of the case is possible only from the inside of the case.
Installation Guide
Removing Side Panels
To remove the side panels, gently pull them outwards from the case.
Installing Motherboard
Place the motherboard inside the case, aligning it with the standoffs. The case supports Mini-ITX, Micro-ATX, and ATX form factor motherboards. Ensure the screw holes align correctly.
Installing 3.5" HDDs
Follow the sequence of diagrams to mount 3.5" Hard Disk Drives into the designated HDD/SSD cage. This typically involves securing the drive with screws and sliding it into the cage.
Installing 2.5" SSDs
Follow the sequence of diagrams to mount 2.5" Solid State Drives into the case. This usually involves using screws to attach the SSD to a mounting point or tray.
Installing the GPU
Insert the Graphics Processing Unit (GPU) into the appropriate PCIe slot on the motherboard. Secure the GPU bracket to the case using a screw.
Installing the Power Supply
Slide the Power Supply Unit (PSU) into its bay located at the bottom of the case, ensuring the PSU fan faces outwards (downwards). Secure the PSU with screws.
Quick Start Guide / Installation
Follow these steps for a quick setup:
- Open the housing.
- Install all computer components following the instructions in the individual assembly instructions for each component.
- Mount the power supply in the housing and connect it to the required components, following the power supply's installation instructions and the instructions of the components that require its connection. The power supply is mounted in a tunnel in the lower part of the case, with the fan facing outside the case (down).
- Check the correct assembly of components and the connection of power plugs.
- Close the housing.
- Connect the monitor, keyboard, and other accessories to the computer.
- Connect the power cord to the socket in the power supply and to the 230V mains socket.
- Set the power switch on the PSU housing to the 'I' position (if present).
Environmental and Disposal Information
This device was designed and made of high-quality reusable materials and components. If the device, its packaging, user's manual, etc. are marked with a [crossed-out waste bin symbol], it means they are subject to segregated household waste collection in compliance with the Directive 2012/19/UE of the European Parliament and of the Council. This marking informs that electric and electronic equipment shall not be thrown away together with household waste after it's been utilized. The user is obliged to bring the utilized equipment to an electric and electronic waste collection point. Those running such collection points, including local collection points, shops, or commune units, provide a convenient system enabling to scrap such equipment. Appropriate waste management aids in avoiding consequences which are harmful for people and the environment, resulting from dangerous materials used in the device, as well as improper storage and processing. Segregated household waste collection aids in recycling materials and components of which the device was made. A household plays a crucial role in contributing to recycling and reusing the waste equipment. This is the stage where the basics are shaped which largely influence the environment being our common good. Households are also one of the biggest users of small electrical equipment. Reasonable management at this stage aids recycling. In the case of improper waste management, fixed penalties may be imposed in accordance with national legal regulations.
