Peavey Bandit 112 TransTube Series Guitar Amplifier

User Manual and Product Overview

Introduction

Congratulations on your purchase of the Peavey Bandit 112 TransTube Series amplifier. This amplifier represents years of research into vacuum tube emulation, resulting in a completely new Bandit. The preamp has been redesigned using patent-applied-for technology that redefines tubelike distortion and harmonic generation in solid-state amplifiers. The new T™ Dynamics circuitry creates the sought-after tube power compression phenomenon. Combined with resonance and presence circuitry, it offers the closest tube amp simulation to date. This compression effect is increased by turning the T. Dynamics control down, which lowers the amp's output power level. For enhanced performance, an external speaker jack increases the power to 100 watts, and a footswitchable effects loop provides greater flexibility.

Front Panel Features

The front panel of the Peavey Bandit 112 features a comprehensive array of controls and inputs for shaping your sound.

High Gain Input (1)

Used for most electric guitars. It is 6 dB louder than the Low Gain input.

Low Gain Input (2)

Provided for instruments with extremely high output levels that could cause overdriving (distortion) of the High Gain input. If both inputs are used simultaneously, the output levels are the same (both are Low Gain).

Volume (3)

Controls the volume level of the Clean channel.

Bright Switch (4)

Provides a preset boost (6 dB) to treble frequencies. To activate, depress the switch to its "in" position.

Channel Select Switch (5)

Allows selection of the Lead or Clean channel. The "in" position selects the Lead channel, and the "out" position selects the Clean channel. Note: Channel selection can also be achieved via the remote footswitch. If remote selection is desired, the channel switch must be in the "in" (Lead) position.

Low, Mid, & High EQ (Clean Channel) (6)

Passive tone controls that regulate the low, mid, and high frequencies of the Clean channel.

Pre Gain (7)

Controls the input volume level of the Lead channel.

Thrash Switch (8)

Notches the mid-range approximately 20 dB.

Gain Switch (9)

Boosts the overall system gain. Depress to the "in" position to activate.

Low, Mid, & High EQ (Lead Channel) (10)

Passive tone controls that regulate the low, mid, and high frequencies of the Lead channel.

Post Gain (11)

Controls the overall volume level of the Lead channel. The final level adjustment should be made after the desired sound has been achieved.

Reverb Level (12)

Controls the overall reverb level.

Effects Send (13)

Output for supplying signals to external low-level effects or signal processing equipment.

Effects Return (14)

Input for returning signals from external low-level effects or signal processing equipment.

Effects Level Switch (15)

Selects the effects loop operating level: -10 dBV (0.3 V RMS) when "out" and 0 dBV (1 V RMS) when "in."

Resonance Switch (16)

Used to fine-tune the low-frequency range of the speaker enclosure by varying the amplifier's damping factor between two presets.

Presence (17)

An active tone control that boosts extreme high frequencies by 6 dB.

T™ Dynamics Control (18)

Adjusts the amplifier's power level from 10 percent to 100 percent. At lower settings, the power compression simulation is more pronounced.

Power LED (19)

Illuminates when AC power is supplied to the amp.

Power Switch (20)

Depress the switch to the "on" position. The red pilot light (LED) illuminates, indicating power is supplied to the unit.

Back Panel Features

The back panel provides connections for external devices and power.

Line Cord (22)

For 120 V products only. Features a three-wire grounded power cord for safety. It is not advisable to remove the ground pin. Use grounding adapters if necessary. Proper grounding reduces noise and shock hazard.

External Speaker Jack (23)

Provides a connection for an external speaker cabinet. Minimum external speaker impedance is 8 ohms (4 ohm total impedance).

Remote Switch Jack (24)

For connecting the supplied remote footswitch. The footswitch selects Lead/Normal channels and bypasses the effects loop. Ensure the plug is fully inserted (second click) for proper operation.

Power Amp Input (25)

Used to connect a line-level signal to the power amplifier.

Preamp Out (26)

Routes the amplified signal to a mixing console, tape recorder, etc. Use a shielded cable. This connection does not affect amplifier operation.

Specifications

Detailed technical specifications for the Peavey Bandit 112.

Rated Power & Load

Power specs measured with T. Dynamics @ 10: 80 W RMS into 8 ohms, 100 W RMS into 4 ohms

Power @ Clipping (typically)

(5% THD, 1 kHz, 120 V AC line): 80 W RMS into 8 ohms, 100 W RMS into 4 ohms

Frequency Response

+0, -3 dB, 60 Hz to 20 kHz, @ 65 W RMS into 8 ohms

Hum & Noise

Greater than 86 dB below rated power

Power Consumption

300 W @ 50/60 Hz, 120 V AC, Domestic
300 W @ 60 Hz, 220-230/240 V AC, Export

Preamp Section

Specs measured @ 1 kHz with controls preset as follows:

Push Bright: Off (Out)
Channel Select: Normal (Out)
Low & High EQ: 10
Mid EQ: 0
Presence: 0 dB
Pre 5: Post Gain @ 10
Gain 6: Thrash, Off (Out)
Normal Levels: with normal volume @ 5
Minimum Levels: with normal volume @ 10

Preamp High Gain Input

Impedance: High-Z, 1 M ohm
Nominal Input Level: -14 dBV, 200 mV RMS
Minimum Input Level: -24 dBV, 60 mV RMS
Maximum Input Level: 0 dBV, 1 V RMS

Preamp Low Gain Input

Impedance: High-Z, 44 K ohms
Nominal Input Level: -8 dBV, 400 mV RMS
Minimum Input Level: -18 dBV, 120 mV RMS
Maximum Input Level: 6 dBV, 2 V RMS

Effects Send

Load Impedance: 1 K ohm or greater
Nominal Output Level: -10 dBV, 0.3 V RMS or 0 dBV, 1 V RMS (if Effects Level is in)

Effects Return

Impedance: High-Z, 22 K ohms
Designed Input Level: -10 dBV, 0.3 V RMS or 0 dBV, 1 V RMS (if Effects Level is in)
(Switching jack provides Effects Send to Effects Return connection when not used)

Preamp Output

Load Impedance: 1 K ohm or greater
Nominal Output Level: 0 dBV, 1 V RMS

Power Amp Input

Impedance: High-Z, 30 K ohms
Designed Input Level: 0 dBV, 1 V RMS
(Switching jack provides preamp output to power amp input connection when not used)

System Hum & Noise @ Nominal Input Level

(20 Hz to 20 kHz unweighted): 72 dB below rated power

Equalization

Special low, mid, & high passive type EQ
Presence: +6 dB @ 5 kHz
Push Bright: +6 dB @ 2 kHz
Push Thrash: -20 dB notch @ 1 kHz in Lead channel
Push Gain: Increases Lead gain
Push Resonance: +6 dB @ cabinet resonance

External Footswitch Functions

Lead Channel Defeat (when selected with button)
Effects Loop Bypass

Dimensions & Weight

20.0" H x 23.375" W x 11.25" D
46.5 lbs.

Tone Settings

Suggested tone settings for various musical styles:

Clean

Settings: Bright: OUT, Channel: CLEAN, Gain: 5, Volume: Adjust to Preference, EQ: Low 5, Mid 5, High 5, Reverb: 5, T. Dynamics: 50%

Jazz

Settings: Bright: OUT, Channel: CLEAN, Gain: 4, Volume: Adjust to Preference, EQ: Low 6, Mid 4, High 6, Reverb: 5, T. Dynamics: 50%

Clean Blues

Settings: Bright: OUT, Channel: CLEAN, Gain: 6, Volume: Adjust to Preference, EQ: Low 7, Mid 3, High 7, Reverb: 5, T. Dynamics: 50%

Metal

Settings: Bright: IN, Channel: LEAD, Gain: 6, Pre Gain: 7, Post Gain: 6, EQ: Low 6, Mid 4, High 6, Reverb: 5, T. Dynamics: 50%

Medium Distortion

Settings: Bright: OUT, Channel: LEAD, Gain: 6, Pre Gain: 7, Post Gain: 6, EQ: Low 6, Mid 4, High 6, Reverb: 5, T. Dynamics: 50%

Dirty Blues

Settings: Bright: OUT, Channel: LEAD, Gain: 7, Pre Gain: 7, Post Gain: 6, EQ: Low 7, Mid 3, High 7, Reverb: 5, T. Dynamics: 50%

Safety Instructions

WARNING: When using electric products, basic cautions should always be followed.

Read all safety and operating instructions before using this product and retain them for future reference.
Obey all cautions in the operating instructions and on the unit.
Follow all operating instructions.
Do not use near water (bathtub, sink, pool, wet basement).
Ensure proper ventilation; do not place flat against a wall or in a built-in enclosure that impedes airflow.
Do not place near heat sources (stove, radiator, other amplifiers).
Connect only to the specified power supply type.
Never break off the ground pin on the power supply cord.
Handle power cords carefully; do not walk on them or place equipment on them. Periodically check cords for damage.
Unplug the power cord when the unit is unused for long periods.
If mounting in an equipment rack, provide rear support.
Clean metal parts with a damp rag. Vinyl covering can be cleaned with a damp rag or ammonia-based cleaner. Disconnect power before cleaning.
Prevent objects from falling into or liquids from spilling into the unit through ventilation holes or openings.
Have the unit checked by a qualified service technician if the power cord/plug is damaged, something has fallen/spilled into the unit, the unit does not operate correctly, or the unit has been dropped/enclosure damaged.
Do not attempt to service the equipment yourself; all service should be done by a qualified technician.
Use only with a recommended cart or stand.
Be aware of noise exposure levels; prolonged exposure to high noise levels can cause permanent hearing loss. Use hearing protection if operating at high volumes.

Warranty Information

This product is covered by a limited warranty, typically one year for the unit and 90 days for tubes and meters, valid only when purchased and registered in the United States or Canada. Exported products are subject to warranty and service as specified by the authorized distributor for each country.

The warranty covers defects in material and workmanship but excludes covers, footswitches, patchcords, tubes, and meters (which have a shorter warranty). Conditions, exclusions, and limitations apply, including voiding the warranty if the product is resold, not purchased from an authorized dealer, damaged by misuse/neglect, or has a altered serial number.

To obtain service, bring the defective item to an authorized dealer or service center with proof of purchase. If they cannot provide service, you will be directed to another authorized location. Alternatively, ship the item prepaid to the Peavey International Service Center with a detailed description of the problem and proof of purchase. Peavey will repair or replace the product at its option and return it freight collect.

Peavey's liability is limited to the purchase price of the product or $500.00, whichever is greater, for damages not related to personal injury or property damage caused by Peavey's negligence. Peavey is not liable for lost profits, incidental, or consequential damages. This limited warranty is in lieu of all other warranties, expressed or implied.

Complete and mail the warranty registration card within 14 days of purchase. Keep your proof of purchase for warranty service. Notify Peavey of any address changes.

	Peavey Backstage Chorus 208 Guitar Amplifier User Manual User manual and specifications for the Peavey Backstage Chorus 208 single unit guitar amplifier, detailing controls, features, and safety instructions.
	Peavey Amplifiers Product Catalog: Guitar, Bass, and Multi-Instrument Comprehensive catalog showcasing Peavey's extensive range of guitar amplifier heads, cabinets, and combos, alongside bass amplifiers and multi-instrument amps. Features detailed specifications, controls, and technical data for models across series like 6505, Classic, Invective, MAX, KB, and Vypyr.
	Peavey Classic 30 / Delta Blues Amplifiers Operating Manual Operating manual for Peavey Classic 30 and Delta Blues all-tube guitar amplifiers. Details features, controls, specifications, and usage instructions for these iconic musical instruments.
	Peavey Backstage Chorus 208 Guitar Amplifier Operating Manual Comprehensive operating manual for the Peavey Backstage Chorus 208 single unit guitar amplifier. Includes detailed descriptions of front panel controls, rear panel connections, technical specifications, tone setting examples, signal path diagram, important safety instructions, and limited warranty information.
	Peavey Backstage Chorus 208 Guitar Amplifier - User Manual & Specifications Comprehensive user manual and technical specifications for the Peavey Backstage Chorus 208 single unit guitar amplifier, including control descriptions, tone settings, and safety information.
	Peavey 210 Powered Enclosure Operating Guide and Specifications Operating guide and technical specifications for the Peavey 210 Powered Enclosure, featuring DDT™ technology, 210 watts RMS power, and dual 10-inch Scorpion™ loudspeakers. Includes safety information and usage guidelines.
	Peavey VYPYR X1 Modeling Guitar Amp Combo - Features and Description Detailed information about the Peavey VYPYR X1, a 20-Watt modeling guitar amp combo featuring TransTube technology, multiple amp and effects models, instrument modeling, and USB connectivity for recording and control.
	Peavey Nashville 112 Amplifier Operating Manual and Specifications Comprehensive operating manual and specifications for the Peavey Nashville 112 amplifier, detailing front and rear panel controls, quick start guide, setting examples, and technical specifications.