Buy electriQ Appliances Online | TVs | Ovens | Dehumidifiers | Security
User Manual for electriQ models including: 49 LED Monitor, eiQ-49CV5UWD120FSHQA
USER MANUAL. 49” LED MONITOR. eiQ-49CV5UWD120FSHQA. Thank you for choosing electriQ. Please read the user manual before using this monitor ...
continuous product development, some variation from the manual is possible. • The availability of features and settings may vary depending on the input source and method of connection. • Although every effort is made to maintain the accuracy of the manual, due to continuous product development, some variation from the manual is possible.
File Info : application/pdf, 18 Pages, 5.05MB
DocumentDocumentUSER MANUAL
49" LED MONITOR
eiQ-49CV5UWD120FSHQA
Thank you for choosing electriQ Please read the user manual before using this monitor and keep it safe for future reference
Visit www.electriQ.co.uk to view our enre range of Intelligent Electricals
CONTENTS
SAFETY
3
WHATS INCLUDED
5
STAND INSTALLATION
6
WALL MOUNTING
7
CONNECTIONS
8
GETTING STARTED
9
MONITOR CONTROLS
9
INITIAL SET UP
9
SHORTCUT BUTTONS
10
MENU OPTIONS
10
OSD MENU
11
INPUT
11
BRIGHTNESS/CONTRAST
11
COLOUR
12
PICTURE QUALITY
12
DISPLAY
13
AUDIO
13
MULTI-WINDOW
14
OSD
14
OTHER
15
TECHNICAL SPECIFICATION
16
TROUBLESHOOTING
17
SUPPORT
17
2
SAFETY INFORMATION
· Read these instructions - All the safety and operating instructions should be read before this product is operated.
· Keep these instructions - The safety and operating instructions should be retained for future reference.
· Heed all warnings - All warnings on the appliance and in the operating instructions should be adhered to.
· Follow all instructions - All operating and usage instructions should be followed.
· Do not use this equipment near water, or in humid environments - The appliance should not be used near water or moisture e.g. in a wet basement or near a swimming pool.
· Clean only with a dry cloth. Do not use solvents or petroleum-based fluids.
· Do not block any ventilation openings. · Do not install near any heat sources such as radiators, stoves or other
apparatus (including amplifiers) that produce heat. · Do not tamper with the supplied plug. This plug is a BS1363 standard
plug. · Protect the power cord from being walked on or trapped, particularly at
the plug and at the point where it exits from the appliance. · Only use attachments/accessories specified by the manufacturer. · Use only with a cart, stand, tripod, bracket or table specified by the
manufacturer or sold with the apparatus. When a cart or stand is used, use caution when moving it to avoid any injuries or damage from it tipping over. · Unplug the apparatus during lightning storms or when unused for long periods of time. · Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as if the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus or it has been exposed to rain or moisture, it does not operate normally or has been dropped. · Please keep the unit in a well-ventilated environment. · The monitor should only be connected to a mains power supply as rated on the back of the equipment. · To prevent overload, do not share the same power supply socket with too many other electronic components. · Do not place any connecting wires where they may be stepped on or tripped over. · Do not place heavy items on the cable as this may cause damage. · When removing from a socket hold by the plug and not the wires. · Disconnect the power immediately and seek professional help if the plug or cable is damaged, liquid has spilt onto the unit, if accidentally exposed to water or moisture, if anything accidentally penetrates the ventilation slots or if the unit does not work normally. · Do not remove the safety covers. There are no user serviceable parts
3
inside. Trying to service the unit yourself is dangerous and may invalidate the product's warranty. Only qualified personnel should service this apparatus. · Do not block ventilation slots on the back cover. The monitor can be placed in a cabinet but ensure at least 5cm (2") clearance all around. Do not tap or shake the screen, this may damage internal components. · WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the apparatus. · WARNING: The wall plug socket is used as a disconnection device and should remain readily accessible. · WARNING: The batteries shall not be exposed to excessive heat such as direct sunlight or fire. · Although every effort is made to maintain the accuracy of the manual, due to continuous product development, some variation from the manual is possible. · The availability of features and settings may vary depending on the input source and method of connection. · Although every effort is made to maintain the accuracy of the manual, due to continuous product development, some variation from the manual is possible. · The availability of features and settings may vary depending on the input source and method of connection. · The available resolutions and refresh rates may be limited by the capabilities and/or settings of the source device.
4
WHAT'S INCLUDED
MONITOR
15 mm
17mm 35mm
SCREW BOLTS
MOUNTING SCREW BOLTS
DP CABLE
POWER SUPPLY
REMOTE CONTROL
USER MANUAL
STAND (UPRIGHT SECTION)
STAND BASE
5
STAND INSTALLATION
1. Open the package, take out the product with foam sll aached, and gently place it on a desktop or table.
2. Take out the two main parts of the stand. Then use the screwdriver (not included) and the screws to fasten base to the stem.
3. Align the stand stem's bracket with the opening on the back of the monitor and carefully insert bracket. The pieces should click into place.
4. Before removing the stand, remove the port cover from the back of monitor. Switch the buon down to remove the monitor from the bracket.
Keep the foam underneath the monitor before aaching the stand. To avoid damage, do not touch the screen when moving the monitor.
NOTES: Due to the heavy weight and dimensions of the LCD screens and their fragile nature, we recommend
that they are unpacked and assembled by 2 people. electriQ and its distributors and dealers are not liable or responsible for damage or injury caused by
improper installaon, improper use or failure to observe these safety instrucons. In such cases any guarantee will expire. The stand can be removed from the rear of the monitor by pressing the quick release buon on the rear of the monitor.
6
WALL MOUNT INSTALLATION This monitor ONLY includes screws which may be used when aaching the monitor to a mount. No mount or mounng accessory is included.
1. Open the package, take out the product with foam sll aached, and gently place it on a desktop or table. Remove the extra parts and the foam covering the monitor. If the monitor was already aached to the stand, remove the stand.
2. Remove the original screws x 4 from the opening in the back of the monitor. Follow the direcons received with your mount, stand, or accessory and install the monitor on the wall or fixture as desired. Remember to use the included screws when aaching anything to the back of the monitor.
Do not discard the original screws as these may be needed for future use. 3. Follow the direcons received with your mount, stand, or accessory and install the monitor on the
wall or fixture as desired.
7
NOTES:
Do not pinch the screen directly with your hand when hanging the product to prevent the screen from breaking.
Due to the heavy weight and dimensions of LCD screens and their fragile nature, we recommend that they are unpacked and assembled by 2 people and professional installers are used to wall mount them (Wall mounng is oponal).
If you do not understand the instrucons, or are unsure how to install this product, please contact a professional for assembly advice and assistance.
Careful consideraon should be made regarding the locaon the monitor is to be wall mounted as some walls are not suitable for installaon. If the monitor is to be mounted on drywall, the mount must be anchored into a wooden stud, concrete block or brick behind the drywall. Installing on drywall alone may not support the weight of the display.
When drilling holes, it is parcularly important to take care of electrical cables, water or gas pipes in the wall. Please follow the instrucons provided by the wall bracket manufacturer and ensure that all fixing screws supplied are used.
electriQ and its distributors and dealers are not liable or responsible for damage or injury caused by improper installaon, improper use or failure to observe these safety instrucons. In such cases any guarantee will expire.
CONNECTIONS AVAILABLE ON THE MONITOR
1
2
3
4
5
1 Audio Output: Insert one and of the Audio cable into
the computer's Audio output to receive the Audio
signals from your monitor.
DP Connector: Insert one end of the DP cable into
2 the computer's DP output and connect the other
end to the monitor's DP port.
HDMI Connector: Insert one end of the
3
HDMI cable into a suitable HDMI source. HDMI output and connect the other end to
the monitor's HDMI port.
4 USB: USB 2.0 connecon.
5 Power Connector: Insert the power connecter
to supply power.
8
GETTING STARTED MONITOR CONTROLS
E Select signal source or Exit the menu Go Up within the Main Menu or increase the value of the selected item Go Down within the Main Menu or decrease the value of the selected item
M Enter the Main OSD Menu and Select submenu Turn the monitor on or Off
INITIAL SETUP
CONNECT THE MONITOR TO A POWER OUTLET
1. Press the POWER buon on the monitor or to turn it on (The indicator will be blue) 2. Connect the relevant cable to the corresponding input on the monitor. The source will be automacally
detected.
9
SHORTCUT BUTTONS
The monitor includes one touch opons to access common sengs.
e c o
Main Menu Display Crosshairs
Power Off Switch HDMI 4K or HDMI 5K
Scene mode switching
MENU OPTIONS
The menu for the monitor can be accessed by pressing the menu buon on the control panel. This menu is separated into the following sub menus: Input source, Brightness/Contrast, Colour Sengs, Picture Quality Sengs, Display, Audio, OSD (On screen display), and other. Details of each menu can be found in the following secon.
10
OSD MENU
INPUT SOURCE
HDMI1
DP1 DP2 HDMI1 HDMI2
Resolution: 3840x2160@30Hz SDR
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
Signal
Switch the signal input or select the source. DP 1, DP2, HDMI1, HDMI2
BRIGHTNESS/CONTRAST
HDMI1
Brightness Blacklevel Contrast DCR
Resolution: 3840x2160@30Hz SDR
90 50 50 Off
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
Brightness Black level Contrast DCR
Adjust the brightness of the display between 0 and 100. Adjust the black level of the display between 0 and 100. Adjust the contrast of the display between 0 and 100. Turn the Dynamic Contrast Rao Feature On or Off.
11
COLOUR SETTINGS
HDMI1
Gamma Picture Mode Color Temperature Low Blue Light Hue Saturation
Resolution: 3840x2160@30Hz SDR
2.2 Standard Warm 0 50 50
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
Gamma Picture Mode
Colour Temperature Low Blue Light Hue Saturaon
Change the Gamma value for the display between 1.8, 2.0, 2.2, 2.4, 2.6
Change the picture mode between Standard, Photo, Movie, Game, FPS and RTS. Change the Colour Temperature of the display to Normal, Warm, Cool or User. When the User Mode is selected, the Red, Green, and Blue values can be adjusted independently between 0 and 100.
Change the blue light emied by the display between0 and 100. Change the Hue value between 0 and 100. Change the Saturaon of the display between 0 and 100.
PICTURE QUALITY SETTINGS
HDMI1
Resolution: 3840x2160@30Hz SDR
Sharpness
50
Response Time
Off
Noise Reduction
Off
Dynamic Luminous Control
Off
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
Sharpness
Response Time Noise Reducon Dynamic Luminance Control
Change the display Sharpness between 0 and 100. Turn the Response Over Drive feature between Off, High, Middle of low Adjust the level of Noise Reducon between Low, Medium, High, or Off.
Turn the Dynamic Luminance Control feature On or Off.
12
DISPLAY
HDMI1
Aspect Ratio HDMIEDID SwitchMode
Resolution: 3840x2160@30Hz SDR
Wide Screen HDMI 5K
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
Aspect Rao Change the image aspect rao to Wide Screen. 4:3 Auto. 1:1 HDMI Switch Change switch between HDMI 4K or HDMI 5K. Mode
AUDIO
HDMI1
Mute Volume Audio Source
Resolution: 3840x2160@30Hz SDR
Off 50 HDMI1
Mute Volume
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
Turn On and off to mute and unmute the audio output. Adjust the output volume between 0 and 100.
13
MULTI-WINDOW
HDMI1
Multi-Window Sub Win2 Input Sub Win3 Input Sub Win4 Input Swap
Resolution: 3840x2160@30Hz SDR
Off DP2 HDMI1 HDMI2
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
Mul-Window Sub Win2 Input
Sub Win3 Input
Sub Win4 Input SWAP
Choose the different formats of mul window display between Off, Picture in Picture (PIP) and Picture By Picture (PBP 2Win) Choose the source of the second window between DP1 , DP2, HDMI1, HDMI 2. Choose the source of the second window between DP1 , DP2, HDMI1, HDMI 2. Choose the source of the second window between DP1 , DP2, HDMI1, HDMI 2. Swap the Primary and Secondary inputs on screen.
OSD
HDMI1
Language OSD H-Position OSD V-Position OSD Transparency OSD Time Out OSD Rotation
Resolution: 3840x2160@30Hz SDR
English 50 50 20 20 Normal
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
Language
Change the OSD Menu display language between English, Chinese, Korean, Russian, Spanish, Japanese and French.
OSD H Posion
Change the horizontal posion of the OSD Menu between 0 and 100.
OSD V Posion
Change the vercal posion of the OSD Menu between 0 and 100.
OSD Transparency Change the transparency value of the OSD Menu between 0 and 100.
OSD Time Out Change how long the OSD Menu is on before it atomically exits.
OSD Rotaon Change the OSD Rotaon Normal,90,180,270 14
10
OTHER
HDMI1
DP Version FreeSync(Adaptive Sync) HDR Reset
Resolution: 3840x2160@30Hz SDR
DP1.4 Off Off
InputSource: HDMI1 Resolution: 3840x2160@30Hz
3 InputSource: Resolution:
InputSource Resolution
4 InputSource Resolution
DP Version
Change the DP version
FreeSync (Adapve Sync)
Turn Free Sync On or Off.
HDR Reset
Turn the HDR on or off. Restore factory default seng.
15
Terminals
Picture
SPECIFICATION
Product Model Screen Size Panel Type Aspect Rao Power Supply Power Consumpon Dimensions (with stand) Net / Gross Weight
Maximum Resoluon Brightness Stac Contrast Viewing Angle (H/V) USB Input HDMI Input Display Port Input Audio Output Remote Control Working Temperature Working Humidity Speaker Specificaons
eiQ-49CV5UWD120FSHQA 49" Diagonal VA Panel 21:9 AC 100-240V ~ 50/60Hz, 2.0A 80W Type, 105W Max 1178.4 * 466.02 * 240 .18 mm 11.0 kg / 14.8 kg 5120 * 1440 350 cd/m2 3000:1 178° / 178° USB 2.0 x 1 HDMI 2.0 x 2 DP 1.4 x 2 x 1 (Headphone Socket) 2m Maximum operang distance 0°C - 40°C 10% - 85% Non-condensing 8 / 3 W
16
TROUBLESHOOTING
Problem No power
Soluon Insert the plug securely into the power outlet.
No picture
Ensure that the equipment is connected properly. Ensure the correct input is selected.
Buons on the monitor don't do anything
Noise or other interference
Disconnect the power plug and then reconnect it. (The unit may not be operang properly due to lightning, stac, or other factors.)
Electronic equipment near the unit may be causing interference. Relocate the unit or move the equipment.
ENVIRONMENTAL PROTECTION
Recycling facilies are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to parcipang civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when deposing your equipment. Please contact the local council for details of your local household waste recycling centers
electriQ UK SUPPORT
www.electriQ.co.uk/support
Call: 0330 390 3061
Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.uk
Unit J6, Lowfields Business Park Lowfields Way, Elland
West Yorkshire, HX5 9DA
17
108.007.13171
H3CQR-HQ
eiQ-49CV5UWD120FSHQA
EIectriQ
2020.12.07
140*19 7mm
120G 80G
zhanglei