Barnett 1.5-5x32mm Crossbow Scope

Introduction

This scope is designed, engineered, and built to offer years of trouble-free service. When used properly, it will deliver outstanding performance in the field, while increasing your level of shooting satisfaction. To avoid damaging the scope or injuring yourself during its operation or use, carefully read these instructions completely and heed all warnings.

⚠ WARNING

• NEVER attempt to look at or view the sun using a scope. Permanent eye damage will result.
• Make certain the crossbow is unloaded and uncocked when attempting to make adjustments to this scope.
• NEVER shoot a crossbow anywhere other than an approved shooting range. Strictly follow the warning and precautionary statements included with your crossbow instruction manual.
• Make certain the scope is mounted far enough forward to preclude contact with it when shooting. Rearward movement (i.e., "crossbow recoil") occurs when the crossbow arrow is discharged. Placing your eye(s) in close proximity or against the scope while shooting will result in personal injury.
• Do not attempt to disassemble or clean the scope internally. Attempting to disassemble the crossbow scope immediately voids the warranty and will render the scope unusable.

Care and Maintenance

• Keep the protective lens covers in place when the scope is not in use.
• Wipe external optical surfaces with the provided lens cloth or optical quality lens paper.
• Remove external dirt or sand with gentle air pressure (e.g., canned compressed air) and a soft brush to avoid scratching the lens finish.
• In a salty environment, wipe the scope with a damp cloth, then with a dry cloth. Wipe down metal portions with a silicone cloth to protect against corrosion. Do not spray with a silicone lubricant aerosol.
• Store this scope in a moisture-free environment. Avoid storing the scope in passenger compartments or trunks of vehicles as temperature can adversely affect the scope's internal lubricants and sealants.

Failure to follow these instructions may result in serious injury and/or property damage.

Scope Breakdown

Diagram showing the parts of the scope:

• 1. Elevation Turret
• 2. Windage Turret
• 3. Speed Adjustment/Magnification
• 4. Ocular Lens Adjustment
• 5. Scope Rings/Bases (Base Screws on Opposite Side)
• 6. Illuminated Reticle On/Off & Brightness Adjustment
• 7. Battery Cover
• 8. Horizontal Reference Crosshair

Adjusting the Ocular Lens

The ocular lens housing has a fast-focus thread that quickly adjusts to make the reticle as sharp as possible for your individual eyesight. Set the focus of the reticle in similar light conditions and at the approximate range (distance) at which you expect to use your scope. Try not to stare at the reticle to get it in focus; it should be sharp the moment you glance through the scope. Note: It may take several attempts to "dial-in" the perfect focus.

Adjusting Eye Relief/Field of View

A good, clear, level crossbow scope "sight picture" or "field of view" is achieved when the crossbow is held in your normal shooting position and a full field can be viewed without straining or stretching your head and/or neck. This optimum adjustment may require moving the scope assembly either forward or backward on the crossbow's picatinny rail. Perform the following steps to adjust:

1. Support the uncocked/unloaded crossbow on a sturdy surface and loosen the scope ring base cap screws using the provided 7/64" Allen wrench.
2. Raise the crossbow to a standard shooting position and look through the scope. Adjust the scope forward or backwards as necessary until a clear, unobstructed field of view can be seen without straining your head and/or neck. Note: Make certain your eye is not in close proximity to the scope assembly. Positioning your eye too closely to the scope assembly will result in injury upon the crossbow's recoil. If your eye is too close to the scope, use the ocular lens adjustment to adjust the scope focus and move your eye further from the lens to preclude contacting it when shooting.
3. Rotate the scope so the horizontal crosshair is parallel to the string and limbs. Once parallel, retighten the top ring screws and double check that the scope hasn't moved from its optimal functioning position.
4. Once set, check the scope assembly every few shots for tightness and ensure it stays securely mounted. Readjust/retighten as appropriate.

Initially Zeroing the Scope

Once you've read your crossbow instruction manual in its entirety and located a safe and secure place to shoot, double-check your backstop. Backstops are used to stop errant shots and protect surrounding property and/or persons from damage and danger.

1. Place the target (one approved for "crossbow use") on the backstop at a measured distance of 10 yards (30 ft. 9.14m).
2. After following all precautionary statements and heeding all warnings, aim the top (20 yard aim point) reticle at the center of the target and execute a shot. Note the point of arrow impact on the target.
3. Remove the caps from the windage and elevation turrets and make a suitable adjustment to the turret to bring the point of impact (POI) closer to the point of aim (POA).

Point of Aim (POA) vs Point of Impact (POI)

Two terms are used exclusively in the optics industry: "point of aim" and "point of impact". Point of aim or POA, simply describes the spot on the target where the shooter is aiming. Point of impact simply refers to where your arrow actually strikes the target. Once you have established your POA (where you intend to hit) and your POI (where you actually hit), perform the following steps to sight in your scope:

• Establish in what direction(s) the bullseye was missed. For instance, if the shot was high, rotate the elevation turret clockwise.
• At 10 yards, both the windage (left and right) turrets move the POA 1/20th of an inch per "click." So 20 clicks will move the POI approximately one inch.
• After achieving the bullseye at 10 yards, move back to 20 yards (60 feet; 18.2 m). Repeat the previous steps to zero-in the scope at 20 yards.
• At 20 yards, both the windage (left and right) turrets move the POA 1/10th of an inch per "click." So 10 clicks will move the POI approximately one inch.

Adjusting the Speed Selector

Adjust the speed dial to the advertised feet per second of your crossbow. At a measured distance of 30 yards (90 ft. 27.4 m) and using the 30 yard reticle aim point (second from top), shoot the crossbow at the target. If the arrow impacts high, turn the speed on the selector higher and the next arrow fired will impact the target lower. If the initial shot impacts low, turn the speed selector lower and the arrow should impact higher on the target. Once the 30 yard reticle is sighted in, the scope is now calibrated.

Note: It is recommended to target shoot your crossbow at all potential distances you intend to shoot in a hunting scenario.

Shooting Aiming Point Gaps

In many instances, you may encounter targets at distances which fall between two aiming points; say for instance, 38 yards. In these cases, you may consider shooting the gap between your 30 and 40 yard aiming points (depending on your crossbow's speed). This is referred to as "shooting the aiming point gap". It is highly recommended to carry a laser range finder with you in all hunting and shooting excursions. This practice minimizes guessing yardage distances to targets and leads to considerably more success in the field.

Illuminated Reticle

The 1.5-5 x 32 mm crossbow scope is equipped with six reticle aim points, which can be illuminated either red or green. The illumination on/off switch and illumination intensity control rheostat for operating the illumination is positioned on the scope's side sporting a distinctive gray push-button. The system is powered by a CR2032 3 3V coinstyle battery, which is located under the screw-on battery cover behind the gray on/off switch. When replacing the battery, ensure that the "positive" (+) is facing up.

The reticle illuminates in 2 daytime and nighttime friendly colors: 1) red and 2) green. There are multiple brightness levels for each color. These range from very low intensity for lowlight use and high intensity for use in bright conditions.

• To power on the illumination, push the gray button once. The reticle will illuminate in green at its lowest illumination setting.
• To change to a red illuminated reticle, hold the gray button down for 2 seconds and release.
• To increase the intensity (once on), depress the gray button and release without any hold time. Each time the button is depressed in this manner, the illumination intensity will increase until it cycles back to its lowest illumination setting.
• To turn the reticle illumination off, hold the gray button down for 5 seconds.

Warranty Information

Barnett scopes are warrantied from manufacturing defects for one year from date of purchase. Barnett reserves the right to repair or replace defective scopes at their discretion.

Barnett Outdoors, LLC
955 Live Oak Street, Tarpon Springs FL 34689, USA
(800) 237-4507
BARNETTCROSSBOWS.COM
Designed by Barnett USA - Made in China

⚠ WARNING - BATTERY SAFETY

DANGER OF INGESTION: This product contains a button cell or coin battery. Death or serious injury can occur if ingested. A swallowed button cell or coin battery can cause INTERNAL CHEMICAL BURNS in as little as 2 HOURS. KEEP new and used batteries OUT OF REACH of CHILDREN. Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

REMOVE and immediately recycle or dispose of used batteries according to local regulations and keep away from children. DO NOT dispose of batteries in household trash or incinerate. Even used batteries may cause severe injury or death. Call a local poison center for treatment information.

Non-rechargeable batteries are not to be recharged. DO NOT force discharge, recharge, disassemble, heat above the manufacturer's specified temperature of 100°C or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.

Ensure batteries are installed correctly according to polarity (+ and -). DO NOT mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc or rechargeable batteries.

Battery type: CR2032 - Nominal voltage: 3V

REMOVE and immediately recycle or dispose of used batteries from equipment not used for an extended period of time according to local regulations. ALWAYS completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries and keep away from children.