VEVOR Living Room Table Set
Model: ZH604
Affordable. Reliable. Home Improvement.
This document provides the original instructions for assembling the VEVOR Living Room Table Set, Model ZH604. Please read all instructions carefully before operating. VEVOR reserves the right to interpret the user manual. The appearance of the product is subject to the actual product received. VEVOR will not provide further notification for technology or software updates.
Safety Instructions
- WARNING FOR YOUNG CHILDREN: This product contains small components. Please ensure they are kept away from small children while assembling.
- NOTES:
- Do not skip any step.
- Do not fully tighten screws until all parts are assembled.
Thank you for choosing this Living Room Table Set. Please read all instructions before use to achieve the best possible results.
SAVE THIS MANUAL
Parts List
The following parts are included in the package:
- Part 1: Base Panel (x1)
- Part 2: Side Panel (x1)
- Part 3: Side Panel (x1)
- Part 4: Side Panel (x1)
- Part 5: Top Support Rail (x1)
- Part 6: Side Panel (x1)
- Part 7: Back Panel (x2)
- Part 8: Back Panel (x1)
- Part 9: Table Top (x1)
- Part 10: Drawer Slide Rail (x1)
- Part 11: Support Rail (x1)
- Part 12: Support Rail (x1)
- Part 13: Support Rail (x1)
- Part 14: Support Rail (x1)
- Part 15: Support Rail (x1)
- Part 16: Sliding Door (x2)
- Part 17: Shelf (x1)
- Part 18: Door Panel (x1)
- Part 19: Door Panel (x1)
Hardware List:
- A: Screw Ø6 X 40 MM (x34+2)
- B: Screw Ø15X9.5MM (x34+2)
- C: Screw Ø6X30MM (x5+1)
- D: Screw Ø21MM (x34+2)
- E: Screw Ø5*15mm (x12+1)
- F: Screw Ø5*40 (x8+1)
- G: Screw M4*60mm (x1)
- H: Screw X8+1 (x8+1)
- I: Screw X2 (x2)
- J: Screw X4+1 (x4+1)
- K: Screw X12+1 (x12+1)
- L: Screw X12 (x12)
- M: Screw 3x16mm (x12)
- N: Screw 20*118/32孔 (x4)
- O: Screw Ø11XH15MM (x4+1)
- P: Screw Ø1.5*26.6*2.2 (x2)
- Q: Screw M6*30 (x4)
- R: Screw M6*10 (x8+1)
- S: Screw X1 (x1)
- T: Hardware Pack (x2)
Assembly Steps
- Attach part 1 to the base using screws A (x12). Ensure correct orientation as shown. [!]
- Connect parts 1, 2, and 3 using screws F (x4). Ensure parts are aligned correctly. [✔]
- Attach parts 4 and 6 to the base assembly using screws A (x4 each). Ensure correct orientation. [!]
- Connect part 5 to parts 4 and 6 using screws B (x4). Ensure correct orientation. [!]
- Assemble the main frame by connecting parts 1, 2, 3, 4, 5, and 6 using screws F (x4). Ensure the frame is square.
- Attach support rails 11, 13, 14, and 15 to the frame using screws A (x6 each). Ensure correct alignment.
- Connect support rails 11 and 12 using screws C (x1) and B (x1).
- Connect support rails 11 and 12 to the frame using screws C (x2) and B (x2).
- Attach support rails 14 and 15 to the top panel (9) using screws B (x3), C (x2), and D (x3).
- Assemble the drawer slides (11, 13, 14, 15) to the main frame using screws B (x12) and D (x12).
- Slide back panels 7 and 8 into the grooves of the assembled frame.
- Attach the top panel (9) to the frame using screws A (x12). Ensure correct alignment. [!]
- Secure the top panel (9) to the frame using screws B (x12) and D (x12).
- Attach drawer slides and supports using screws L (x12), M (x12), and H (x8).
- Insert shelves (17) into the designated slots.
- Attach sliding doors (16) to the top and bottom tracks.
- Assemble door panels (18 and 19) using screws K (x6), P (x2), N (x2), R (x4), I (x1), and J (x2).
- Assemble the second door panel (19) using screws K (x6), P (x2), N (x2), R (x4), I (x1), and J (x2).
- Attach the assembled door panels (18 and 19) to the unit using hardware T (x2). Ensure smooth sliding action.
Tips
If you accidentally spill water on the table top, please wipe it with a dry towel immediately to prevent the wooden part from being soaked.
Note
- The product is intended for indoor use only and must be assembled and used according to the manual. Personal injury or damage may occur if used outside of intended purposes or if modified.
- The seller assumes no responsibility for injury or damage caused by incorrect assembly or improper use.
- Avoid long-term exposure to humid environments to prevent mildew.
- Keep the product away from fire sources and high temperatures.
- Do not expose the product to direct sunlight.
- Do not place hot objects on the product's surface.
- If any parts are defective or missing after unpacking, cease assembly immediately and contact the seller.
- Assemble the item on a spacious surface and do not place the unwrapped product directly on the ground to avoid damage. Do not stand or sit on the wooden boards.
- Wear gloves during assembly/disassembly to avoid scratches from sharp edges.
- Match parts and fittings based on the part numbers in the manual.
- If a part does not match the fitting, check the piece as specified in this manual.
- During assembly, loosely align all screws with pre-drilled holes, then tighten screws one by one.
- Periodically inspect screw tightness during use and retighten if necessary to ensure structural integrity.
- If water or other liquid is spilled on the surface, wipe clean immediately with a dry towel.
- Keep the product away from sharp, pointed objects and corrosive substances to prevent damage. Place the item on a level, solid ground during use.
Product Parameter
| Model | ZH604 |
|---|---|
| Safe Loading Weight | 200lbs |
| Product Size | 1676*396*710mm |
Sanven Technology Ltd.
Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
