Allen Heath Sq5 Manual Pdf - AP11089 Issue 2 Introduction
Safety Before powering on the SQ, read the safety instructions sheet (AP9240/CL1-1) that is supplied along wi th this guide. For your own safety and that of the operator, technical crew and performers, follow all instructions and
AP11089 Issue 2
Introduction
Safety
Before powering on the SQ, read the safety instructions sheet (AP9240/CL1-1) that is supplied along with this guide. For your own safety and that of the operator, technical crew and performers, follow all instructions and heed all warnings included in these documents and printed directly on the equipment.
Registration
To be kept informed of updates, the latest firmware and new releases for the SQ range, register your SQ-5 at www.allen-heath.com/register
Firmware and Reference Guide
This introduction is intended to give you an overview of the SQ-5 hardware and outline operating principles. Visit www.allen-heath.com to obtain the latest version of firmware and reference guide. The latest firmware is required if you intend to use any SQ Apps with your SQ.
Features
The SQ is a high resolution 96kHz audio mixing console. It has been designed using the latest technology to provide the most detailed and accurate sound quality, along with a range of options for expandability and integration.
SQ Range 48 input channels with preamp, HPF, PEQ, gate, comp, delay 32 output channels (LR, 12 mono/stereo Mix, 3 Stereo Matrix) 8 stereo FX with dedicated return channels 8 Mute groups, 8 DCA groups Source patching (Local, SLink remote, Option card, USB) Output socket and Insert I/O patching Multi-channel USB streaming and direct to USB drive recording Talkback mic input, dual footswitch control, wireless control
SQ-5 Specific 96 fader strips (16+1 faders, 6 layers) 16 local mic/line input sockets 3 local stereo line input sockets 12 XLR + 2 TRS output sockets 8 assignable SoftKeys Rack mountable
SLink Port Compatibility DX168, DX16-4W, DX Hub AR2412, AR84, AB168 ME-U, ME-1, ME-500
Sample Rate 96kHz 48kHz 48kHz
Protocol DX
dSnake dSnake
Max Length 100m 120m
Cat5e or higher Cat5e or higher Cat5e or higher
SQ-5-RK19 SQ-BRACKET AP11332 AR84 AR2412 AB168 DX168 DX164-W DX-HUB AH9650 AH9981 AH9651
Accessories
19" Rack Mounting Kit (12u) Detachable Metal Bracket for iPad/tablet Water repellent polyester dustcover with printed logo 8 XLR input, 4 XLR output, dSnake Remote AudioRack (Rackmount) 24 XLR input, 12 XLR output dSnake Remote AudioRack (Rackmount) 16 XLR Input, 8 XLR Output, dSnake Remote AudioRack (StageBox/Rackmount) 16 XLR Input, 8 XLR Output, 96kHz DX Remote AudioRack (StageBox/Rackmount) 16 XLR Input, 4 XLR Output, 96kHz DX Wall Mount Audio Expander Remote Audio Hub with 4 DX Link ports (Rackmount kit available) 100m drum of EtherFlex Cat5e with locking Neutrik EtherCon connectors 50m drum of EtherFlex Cat5e with locking Neutrik EtherCon connectors 20m of Neutrik EtherFlex Cat5e with locking Neutrik EtherCon connectors
Touch Screen, Screen Select Keys and Screen Encoder
View processing and access the routing and setup menus using keys below. Touch to select a parameter and use the rotary to adjust values.
Fader Strips and Layer Select Keys
6 layers of 16 faders provide 96 assignable strips for access to any combination of channels, returns, masters and DCAs. Each strip has fader, mute, select and PAFL keys, peak and signal meter.
Ident Strip
LCD displays show channel name and colour for each of the 16 strips. Press the `View' key to see secondary information such as input source.
Channel (Pre/HPF/Gate/Comp)
Physical controls for the selected channel. Preamp, HPF frequency, Gate threshold, Comp threshold.
Channel (PEQ/GEQ)
Physical controls for the selected channel. EQ band select keys and parametric controls. Use the `Fader Flip' key to present selected mix GEQ on faders.
Pan Control
Master Strip and Mix Select Keys
Press a blue `Mix' key to present its sends on the 16 faders and its master on the master fader strip. Select `LR' to work with the main LR mix and channel faders.
FX Send Select Keys
Press a blue `FX' key to present its sends on the 16 faders and its master send on the master fader strip.
Headphone Output and Level Control
Main Meter
Displays the LR Mix or selected PAFL signal level.
Talk Key
Momentary or latching switch for the talkback microphone.
SQ-Drive Port
Record/play audio direct to/from a USB drive. Transfer scene, show and library data using a USB key. Update SQ firmware.
ST3 Input
3.5mm stereo jack input, can be used for connection to an external background music device.
Pre Fade and Assign Keys
Hold `Pre-Fade' and press `Sel' to toggle channels pre or post fade to the mix. Hold `Assign' and press `Sel' to route channels to the selected mix.
CH to All Mix Key
Press and hold to present all sends to mixes for the currently selected channel. The ident strip displays mix names.
Copy/Paste/Reset Keys
Used to copy, paste or reset processing blocks or channel parameters.
Library Key
Opens different libraries to enable save and recall of presets for channel/mix/FX processing.
Assignable SoftKeys
Use Setup screen to assign functions such as mutes, tap tempo, scene recall, SQ-Drive control and more.
Local Mic/Line Inputs Local Stereo Line Inputs Talkback Mic Input Local XLR Outputs Local TRS Jack Outputs AES Digital Output Mono/Dual Footswitch Connection Mains Power Input and Switch I/O Port - Option Card
Multi-format multi-channel digital audio
USB-B Port
Connection to a computer for multi-channel audio and MIDI I/O
Network Port
Connect to a router for network/wireless control
SLink Port
For connection to Allen&Heath remote audio racks, including AB, AR and DX ranges, as well as the ME personal monitoring system
Powering On
i. Connect power lead (26). ii. Connect input sources using (19), (20) and (21). iii. Connect outputs (22) and (23) to amplifiers, speakers or line level inputs on other equipment. iv. If required, connect digital I/O such as AudioRacks or Computers using (24), (27), (28) and (30). v. If you are using a footswitch, connect this (25). vi. Switch on the SQ using the push switch (26). vii. Power on any connected amplifiers or powered speakers.
Setup
To reset all mix, parameter and routing settings go to the `Scenes' screen (1), then press and hold the `Reset Mix Settings' button. This will `zero' the desk without deleting saved scenes or libraries.
To check or alter patching, go to the `I/O' screen (1) and use the matrix to patch from Local/Digital Inputs to SQ input channels, and to patch SQ outputs [LR/Mix/Group/Matrix/DirectOut] to Local/Digital Outputs.
Workflow
Press a blue `LR', `Mix' or `FX' Key to present send levels for the selected Mix on the 16 Fader Strips. Use the Layer Keys (2) to move through the 6 layers of faders and adjust individual levels. The Master strip (7) controls the master send level of the selected Mix/FX. Select a strip by pressing the green `Sel' Key on a Fader Strip (2) or the Master Strip (7). The physical controls (4), (5) and (6) can now be used to adjust parameters for the selected strip. Go to the `Processing' screen to see an overview of the processing for the selected strip. Tap on any part of the processing to see a detailed view, then touch a parameter on-screen and use the touch screen encoder (1) to adjust. Mute Keys are illuminated when a strip is muted. By default, PAFL (Pre/After Fade Listen) Keys allow you to route one channel at a time to the PAFL bus/Phones output. PAFL settings can be changed in the `Setup' screen.
Mix sends set to `Post Fade' follow the LR send levels. To toggle channels between `Pre Fade' and `Post Fade' for the selected Mix, hold the `Pre Fade' Key and use `Sel' Keys. To assign or un-assign a strip from the currently selected mix, hold the `Assign' Key and use `Sel' Keys.
Pressing and holding the `CH to All Mix' Key will display the send levels for the currently selected strip across the main fader strips.
Press the `FX' Key to see and adjust FX engines. Use the `Library' Key (17) to recall FX types and presets - change parameters by selecting on-screen and using the touch screen encoder. FX busses 1 to 4 (8) send to FX engines 1 to 4 by default. FX Return channels can be routed to Mixes in the same way as stereo input channels. Hold the `Copy' Key and press an `In' Key (4) (5), a `Sel' Key (2) (7), or on-screen processing to copy it. Hold the `Paste' Key and press a `Sel' Key (2) (7) to paste the copied processing to another channel. Hold the `Reset' Key and press an `In' Key (4) (5), a `Sel' Key (2) (7), or on-screen to reset parameters.
Storing and Recalling
A `Scene' is used to store or recall a mix. A `Show' comprises multiple scenes and all settings. Press the `Scenes' Key to access the list of scenes in the current show. Use a combination of scene filters and `Safes' to decide which settings/parameters/strips are affected when a scene is recalled.
Powering Off
i. Power off any connected amplifiers or powered speakers. ii. Navigate to the `Home' screen and select `Shut Down' iii. Switch off the unit using the push switch (26).
Balanced mono/stereo inputs ST1 and ST2 Inputs ST3 Input
Balanced XLR Outputs Balanced Jack Outputs
SLink AES Stereo Digital Output
Rear USB Connection Network Connection Footswitch
Connections
Mic or line level Line level
XLR ¼" TRS Jack
1=Gnd, 2=+, 3= Tip= +, Ring= -, Sleeve=Gnd
Line level Line level
3.5mm Jack XLR
Tip=Left, Ring=Right, Sleeve=Gnd 1=Gnd, 2= +, 3= -
Line level
¼" TRS Jack
Tip= +, Ring= -, Sleeve=Gnd
RJ45/EtherCON. Use Cat5e or higher. Refer to individual expansion unit instructions.
Digital
XLR
Use 110 AES Cable
USB-B, Conforms to USB 2.0 standard
RJ45, Use Cat5e or higher
¼" TRS (dual) or TS (mono) Jack
Further Information and Support
There are many support resources available through our website including user guides, knowledgebase articles and access to the Allen & Heath Digital Community.
For local language support, please contact the Allen & Heath distributor for your region.
Limited One Year Manufacturer's Warranty
Allen & Heath warrants the Allen & Heath -branded hardware product and accessories contained in the original packaging ("Allen & Heath Product") against defects in materials and workmanship when used in accordance with Allen & Heath's user manuals, technical specifications and other Allen & Heath product published guidelines for a period of ONE (1) YEAR from the date of original purchase by the end-user purchaser ("Warranty Period").
This warranty does not apply to any non-Allen & Heath branded hardware products or any software, even if packaged or sold with Allen & Heath hardware.
Please refer to the licensing agreement accompanying the software for details of your rights with respect to the use of software/firmware ("EULA").
Details of the EULA, warranty policy and other useful information can be found on the Allen & Heath website: www.allen-heath.com/legal.
Repair or replacement under the terms of the warranty does not provide right to extension or renewal of the warranty period. Repair or direct replacement of the product under the terms of this warranty may be fulfilled with functionally equivalent service exchange units.
This warranty is not transferable. This warranty will be the purchaser's sole and exclusive remedy and neither Allen & Heath nor its approved service centres shall be liable for any incidental or consequential damages or breach of any express or implied warranty of this product.
Conditions of Warranty
The equipment has not been subject to misuse either intended or accidental, neglect, or alteration other than as described in the User Guide or Service Manual, or approved by Allen & Heath. The warranty does not cover fader wear and tear.
Any necessary adjustment, alteration or repair has been carried out by an authorised Allen & Heath distributor or agent. The defective unit is to be returned carriage prepaid to the place of purchase, an authorised Allen & Heath distributor or agent with proof of purchase. Please discuss this with the distributor or the agent before shipping. Units returned should be packed in the original carton to avoid transit damage.
DISCLAIMER: Allen & Heath shall not be liable for the loss of any saved/stored data in products that are either repaired or replaced.
Check with your Allen & Heath distributor or agent for any additional warranty information which may apply. If further assistance is required please contact Allen & Heath Ltd.
Any changes or modifications to the equipment not approved by Allen & Heath could void the compliance of the product and therefore the user's authority to operate it.
SQ Series products comply with the European Electromagnetic Compatibility directive 2014/30/EU and the European Low Voltage directive 2014/35/EU. Any changes or modifications to the product not approved by Allen & Heath could void the compliance of the product and therefore the user's authority to operate it.
SQ-5 Introduction | AP11089 Issue 2 Copyright © 2017 Allen & Heath. All rights reserved.
ALLEN&HEATH
Allen & Heath Limited, Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK
www.allen-heath.com
macOS Version 10.15.6 (Build 19G73) Quartz PDFContext Preview