Your Cell Phone Signal Booster Store | Bolton Technical
Installation Guide for WILSONPRO models including: A500-SR Single Room Cell Signal Booster, A500-SR, Single Room Cell Signal Booster
WilsonPro Signal Booster Kit for Single Rooms | Bolton Technical
WilsonPro Single Room Signal Booster Kit | Bolton Technical Africa
3 (STEP 2 cont.) Point the Outside Antenna toward the nearest cell phone tower. To find the nearest tower, use an app such as ‘Open Signal’. This is the most critical
File Info : application/pdf, 18 Pages, 1.78MB
DocumentDocumentA WILSON ELECTRONICS BRAND Installation Guide S Cell Signal Booster Index Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 STEP 1 Attach Booster Antenna to Booster & Place in Desired Location. . . . . . . . . . . . . 2 STEP 2 Mount & Point Outside Antenna Toward Nearest Cell Tower. . . . . . . . . . . . . . . . 2 STEP 3 Route & Connect Outside Antenna To Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 STEP 4 Power Up The Booster & Optimize The System . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Status Light Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Package Contents 5 able Outside Antenna & L-Bracket Antenna Mount Power Supply 1 STEP 1 Attach Booster Antenna to Booster & Place In Desired Location Attach the Booster Antenna to the Single Room Booster and place in room where stronger cell signal is needed. Booster Antenna Single Room Booster STEP 2 Mount & Point Outside Antenna Toward Nearest Cell Tower Pole mounting is preferred because it will be easier to adjust to the direction of the cell tower. Use the U-Bolts to attach the Antenna to a pole or exhaust pipe on roof. 2 Outside Antenna attach L-Bracket to U-Bolts drip holes attach L-Bracket to antenna (STEP 2 cont.) Point the Outside Antenna toward the nearest cell phone tower. To find the nearest tower, use an app such as `Open Signal'. This is the most critical step of the installation process because it will determine the overall performance of the Booster System. Side Mounting Side mounting is a option if you can still obtain strong signal. Note: Drip holes should be pointed down towards ground. drip holes 3 STEP 3 Route & Connect Outside Antenna To Booster Connect the Cable to Outside Antenna and route and connect cable to Booster. All connections should be finger tightened only. STEP 4 Power Up The Booster & Optimize The System Plug the Power Supply into wall outlet then connect into end of Booster. NOTE: We strongly recommend using a power strip with surge protection. 4 Status Lights will appear at the top (STEP 4 cont.) After powering up your system, check to see how your talk, text, and data rates have improved. If more is desired, you can optimize your system. Rotate the Outside Antenna in 1/8 turn increments, after each turn, unplug and reconnect the Booster to power while observing the signal level on your cell phone from the Inside Antenna's projected area. When you have determined a direction that gives you the strongest signal, secure the Outside Antenna in place. Below gives you an idea of how much boosted cell signal coverage this system will bring indoors based on how strong the outside signal is. If the cell signal outside your home is: Strong Good Weak None Your boosted cell signal will cover: Large Medium Small Room Room Room None After each rotation, observe signal level on your cell phone from the Inside Antenna's projected area. 5 Status Light Patterns GREEN This indicates that your Single Room Booster is functioning properly and there are no issues with installation. SOLID RED . This is due to a feedback loop condition called oscillation. This is a built in safety feature that causes a band to shut nearby cell tower. Refer to Troubleshooting section. BLINKING GREEN, RED This indicates that the Booster is operating at a reduced gain to prevent oscillation (feedback). This is a built in safety feature to prevent harmful interference with a nearby cell tower. If you are Single Room Booster Lights Band Band 3 1 Band 8 6 (Status Light Patterns cont.) already experiencing the desired signal boost, then no further adjustments are necessary. If you are not experiencing the desired boost in coverage then refer to the Troubleshooting section. BLINKING GREEN, YELLOW This indicates Band has reduced gain. This indicates that one or more of the Booster bands has reduced power due to overload from nearby cell tower. This is a built in safety feature to prevent harmful interference with a nearby cell tower. If you are already experiencing the desired signal boost, then no further adjustments are necessary. If you are not experiencing the desired boost in coverage then refer to the Troubleshooting section. SOLID YELLOW adjusted. Refer to Troubleshooting section. . Outside Antenna must be LIGHTS OFF . 7 Troubleshooting FIXING RED LIGHT ISSUES This involves Solid Red & Blinking Green/Red lights. Tighten all cable connections (be sure to handtighten only, do NOT use tools). You may want to undo and redo the connection completely. Unplug and replug in Power Supply. Increase the distance (horizontally or vertically) between the Outside and Inside Antennas. Add included cable if needed. Unplug and replug in Power Supply. FIXING ANY YELLOW LIGHT ISSUES This involves Solid Yellow & Blinking Green/Yellow lights. Outside Antenna must be adjusted. Disconnect and reconnect power between adjustments. Wait at least 10 seconds between adjustments for the lights to reset. Pole Mount Option: Rotate the Outside Antenna away from the strongest cellular signal in small increments (1/8 turn) until the light turns green. Unplug and replug in Power Supply. Mounting On Side Of Roof Option: Change mount location. Move the Outside Antenna to location of the home/building to see if the lights turn green. Unplug and replug in Power Supply. Then secure in place. 8 Safety Guidelines Verify that both the Outside Antenna and the adapter extension cable are connected to the Signal Amplifier before powering up the Signal Amplifier. Use only the Power Supply provided in this package. Use of an incorrect Power Supply may damage your equipment. RF Safety Warning: Any antenna used with this device must be located at least 20cm from all persons. AWS Warning: The Outside Antenna must be installed no higher than above ground. This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by or licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. 9 Antenna Info The following accessories are certified by the Boosters. to be used with the Cell Signal INSIDE ANTENNA INFO # Antenna Type BT50206 Omni 50 OUTSIDE ANTENNA INFO # Antenna Type BT974884 Directional 50 BT974877 Omni 50 10 Specifications Model ICASA Connectors Antenna Impedence Frequency Power output for single cell phone (Uplink) dBm Power output for single cell phone (Downlink) dBm Power Requirements Single Room Cell Signal Booster ale 50 Ohms 880-915 / 925-960 1710-1785 / 1805-1880 1920-1980 / 2110-2170 30 30 30 15 17 20 5 V / 3 A Each Signal Booster is individually tested and factory set to ensure ICASA compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster's microprocessor. This device complies with ICASA rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by could void the authority to operate this equipment. 11 Notes 011 749 3.085 www.boltontec.hnical.co.za 12 sales@boltontechnical.co.za Notes 011 749 3.085 www.boltontec.hnical.co.za sales@boltontechnical.co.za 13 Notes 011 749 3.085 www.boltontec.hnical.co.za 14 sales@boltontechnical.co.za 1 YEAR WARRANTY WilsonPro Signal Boosters are warranted for one year against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer's expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by WilsonPro shall, at its option, either repair or replace the product. This warranty does not apply to any Signal Boosters determined by WilsonPro to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties. Replacement products may include refurbished WilsonPro products that have been recertified to conform with product specifications. RMA numbers may be obtained by contacting Customer Support. DISCLAIMER: The information provided by WilsonPro is believed to be complete and accurate. However, no responsibility is assumed by WilsonPro for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use. 15 A WILSON ELECTRONICS BRAND JT Business Park, 5 Rydal Ln, Lon.glake, Johannesburg, 1609 011 749 3.085 www.boltontec.hnical.co.za sales@boltontechnical.co.za Copyright © 2020 WilsonPro. All rights reserved.WilsonPro products covered by U.S. patent(s) and pending application(s) NOT AFFILIATED WITH WILSON ANTENNA GDE000364_001_11.30.20