Quick-Mount Quick Start Guide

Package Contents

• Mount Arm
• Universal Ball Mount
• Bracket Mount
• Rotation Collar
• Stacking Washer
• Ball Mount Washer

Supported Products

The Quick Mount is compatible with the GigaBeam™, LTUTM Lite, NanoBeam®, NanoStation®, NanoStationloco, and UniFi® Building-to-Building Bridge.

• NBE-2AC-13, NBE-M5-16, UBB, or GBE using the Universal Ball Mount
• NBE-5AC-Gen2 or NBE-M5-19 using the Universal Ball Mount and Metal Washer
• loco5AC, NS-5AC, or LTU-Lite using the Ball Mount Assembly

Hardware Overview

The Quick-Mount assembly consists of the following components:

• 1. Stacking Washer: Part of the Quick-Mount assembly that locks the Rotation Collar into place.
• 2. Rotation Collar: Part of the Quick-Mount assembly that stabilizes the base of the Mount Arm.
• 3. Mount Arm: Adjustable mount compatible with a variety of Ubiquiti CPE devices.
• 4. Ball Mount Washer: Used in conjunction with the Universal Ball Mount when installing the NBE-5AC-Gen2 or NBE-M5-19.
• 5. Universal Ball Mount: Used when installing the NBE-5AC-Gen2, NBE-2AC-13, NBE-M5-19, NBE-M5-16, UBB, or GBE.
• 6. Bracket Mount: Used when installing the loco5AC, NS-5AC, or LTU-Lite.

Note: The device's Lock Ring will also be used during installation.

Models

Compatible with Universal Ball Mount:

• NBE-2AC-13
• NBE-M5-16
• UBB
• GBE

Compatible with Universal Ball Mount and Ball Mount Washer:

• NBE-5AC-Gen2
• NBE-M5-19

Compatible with Ball Mount Assembly:

• loco5AC
• NS-5AC
• LTU-Lite

Installation

Before You Begin

Insert the Mount Arm into the Rotation Collar and press until it is locked in.

Note: The screw end should extend past the Rotation Collar for installation.

Installation Steps:

1. Attach Stacking Washer: Secure the Stacking Washer to the mounting surface using a screw.

   Diagram Description: A screwdriver is shown attaching the Stacking Washer to a wall with a screw.

2. Drill Pilot Hole: Drill a 3 mm (1/8") pilot hole into the mounting surface.

   Diagram Description: A yellow drill is shown drilling a 3 mm (1/8") hole into a white surface.

3. Attach Mount Arm Assembly: Align and attach the Mount Arm assembly to the Stacking Washer on the wall.

   Diagram Description: The Mount Arm assembly is shown being attached to the Stacking Washer on the wall.

4. Secure Mount Arm: Ensure the Mount Arm assembly is firmly attached.

   Diagram Description: The Mount Arm assembly is shown secured to the mounting surface.

5. Tighten Adjustment Screw: Tighten the adjustment screw on the Mount Arm to secure the position.

   Diagram Description: A close-up shows the adjustment screw on the Mount Arm being tightened.

6. Mount Device:

   • Attach the Universal Ball Mount to the Mount Arm.
   • Alternatively, attach the Bracket Mount to the Mount Arm.

   Note: Add the Ball Mount Washer when installing the NBE-5AC-Gen2 or NBE-M5-19.

   Diagram Description: Two scenarios are shown: one with a dish-like device (NBE) being attached via the Universal Ball Mount, and another with a rectangular device (loco/NS/LTU) being attached via the Bracket Mount.

7. Adjust Position: Adjust the device's position and orientation as needed.

   Diagram Description: Arrows indicate the ability to adjust the mounted device in multiple directions (up, down, left, right, tilt).

Specifications

Limited Warranty

For warranty details, visit: ui.com/support/warranty

The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions.

Declaration of Conformity

Refer to the official documentation for the Declaration of Conformity.

Online Resources

Additional resources and support are available online.