GT-Lite GT-BU-G150M Motion Sensing LED Garage Light

Product Specifications

• Model: GT-BU-G150M
• Lumens: 15,000LM
• Wattage: 140W
• Equivalent to: 750W Incandescent
• LED Lifespan: 30,000 Hours
• Operating Voltage: 120V AC
• CRI: 80
• Color Temperature: 5000K Daylight
• Base Type: E26 / Standard Edison Base
• Motion Sensor Detection Range: 16ft - 22ft
• Motion Sensor Delay: 30 Seconds
• Motion Activation: Below 15 lux ambient light
• Rating: Damp Rated
• Operating Temperature: -4°F to 113°F (-20°C to 45°C)

Installation Diagram

The installation diagram shows a connection for a 120-277V AC power supply. It illustrates the neutral and live connections for both a CFL bulb and an LED bulb, with the E26 base being common to both.

Troubleshooting Guide

Cleaning Instructions

1. Turn power OFF.
2. Use a soft cloth and a mild, non-abrasive glass cleaner.
3. Lightly wipe and clean the fixture.
4. DO NOT use solvents.
5. DO NOT use cleaners containing abrasive ingredients.
6. NEVER spray cleaning liquid directly onto the LEDs, fixture, or wiring.

Safety Warnings and Precautions

WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

This product may present a possible shock or fire hazard if improperly installed or mounted. Products should be installed following these instructions, local electrical codes, and the current National Electric Code (NEC).

• When using product, basic precautions should always be followed.
• Read and follow all instructions and observe all warnings.
• Carefully read and understand the information given in this manual before beginning installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal. Save these instructions and warnings.
• Do not look directly at the LED lights for any length of time.
• Do not shine the light directly into other people's eyes.

CAUTION:

• NEVER submerge this product in water!
• Do not install this bulb in places where water accumulates.
• Do not use on hot surfaces.
• Do not remove the lens protecting the LED.
• Do not use in areas near a gas source.
• The LED light source cannot be changed.
• This light is not intended for use in potentially explosive environments. This is NOT a vapor proof light.
• This bulb is NOT A TOY and is not suitable for use by children.

Additional Warnings:

• Do not dismantle this light. There are NO replaceable LEDs or serviceable parts.
• Do not install this light inside of undersized enclosures.
• Suitable for fixtures rated for temperatures ranging from -4°F to 113°F.
• NOT Suitable for enclosed fixtures.
• Do not use where exposed to standing water.
• Do not leave bare wires exposed outside of the electrical connections. Make sure wiring section is insulated.
• DO NOT USE WITH DIMMERS. This lamp is not usable with any sort of dimmer. Using this lamp with a dimmer of any kind will void the warranty.

Installation Instructions

1. Before installing the bulb, shut off power supply at the circuit breaker panel to avoid electrical shock. It is recommended that surge/lightning protection be installed. Ballast must be bypassed if present.
2. Remove old bulb.
3. Screw new bulb in clockwise. Do not overtighten. Overtightening may cause damage to the light.
4. Individually pivot each of the 4 adjustable panels down to best cover the desired space. Depending on the type of light fixture, it may be necessary to pivot light heads out of the way before screwing the bulb into the fixture.
5. Restore power.
6. Turn on light switch. Bulb will illuminate immediately if motion sensor is off.
7. Activate the motion sensor by toggling the switch placed on the side of the light into the ON position. If the switch is OFF, the bulb will operate like a standard light bulb.
8. Adjust all angles as needed.
9. Do not stare directly into LED lights when adjusting settings.

Warranty Information

This product is guaranteed against failure due to factory defects in materials or workmanship for one (1) year from the date of purchase. This warranty is non-transferable and applies only to the original owner. Proof of purchase is required for repair or replacement. This warranty does not cover normal wear of parts or damage resulting from any misuse of the product. Misuse of the product includes but is not limited to: using in extreme weather conditions, opening the housing of the product, or attempted remodel/alterations made to product.

FCC Compliance

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that of the receiver. (4) Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.