User Guide for ALTA WINDOW FASHIONS models including: Bliss Bridge USB, Bridge USB, USB
Alta Window Fashions | Programming Guides //
Declarations U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. FCC SAR Warning: RF Exposure Information (SAR): The SAR limit of USA (FCC)is 1.6W/Kg averaged over one gram of tissue. Product Type: BLISS Bridge (FCC ID: 2AU29AMPRFWIFIUSB) has also been tested against this SAR limit. The device was tested for typical body-worn operations to keep the BLISS Bridge at least 5mm from the body. When worn on body must be correct back clip for this product, use of non-approved accessories may result in exposure levels which exceed the uncontrolled environmental RF exposure limits. FCC SAR Warning: The SAR limit of IC is 1.6W/Kg averaged over one gram of tissue. Product Type: BLISS Bridge, model number: BLISS Bridge Wifi and RF (IC: 25624-AMPRFWIFI) has also been tested against this SAR limit. The device was tested for typical body-worn operations to keep the BLISS Bridge at least 5mm from the body. When worn on body must be correct back clip for this product, use of non-approved accessories may result in exposure levels which exceed the uncontrolled environmental RF exposure limits. Le SAR de IC est limité à 16w / kg, avec une moyenne par gramme. Produits Type: BLISS Bridge, type: BLISS Bridge Wifi and RF (IC: 25624-AMPRFWIFI) a également été testé pour la limite SAR. Ce dispositif est utilisé pour tester des opérations d `usure corporelle typiques et des opérations en direction du Haut de physique, de manière à maintenir une distance d' au moins 5mm entre le BLISS Bridge et le visage. Osure.` TM BLISS BRIDGE QUICK START GUIDE Product Certification The BLISS Bridge allows users to link their motorized shades and blinds into a Wi-Fi network enabling control via smart APP and interaction with other IoT products. Step 1 Please scan the QR Code below to download the BLISS app. Scan the QR code to download the app on on the Apple Store. Scan the QR code to get the app on Google Play. Step 2 Please scan the QR Code below for additional videos on linking the BLISS Bridge with your home Wi-Fi router, setting up the BLISS app, and establishing a connection with other IoT applications. Additional Videos Additional Guides Please scan the QR Code for additional BLISS programming and setup guides. Updated 1/2022 Folds 90 degrees TM BLISS BRIDGE USB LED Indicator Programming Button Product Parameter Input Voltage Input Power WiFi Network Shade Control Frequency Range Protection Class Operation Temperature 5V DC (USB Type A) 1000mA 2.4Ghz only (802.1 1b/n/g) 433.92 Mhz 30 meters or 98 feet IP20 32°F to 104°F (0°C to 40°C) Status Indicator Color Constant Blue Slow Flashing Red Slow Flashing Yellow Quick Flashing Red Slow Flashing Purple Slow Flashing Green Meaning Working fine Wi-Fi is disconnected Wi-Fi is connected Bridge reset Pairing underway Upgrade in progress Duration Constant Continuously till status change Continuously till status change 5 times Continuously till status change Continuously till status change Programming / Pairing Press and hold programming button for about 2 seconds, then release until the LED blinks purple. Reset Press and hold programming button for about 10 seconds, then release until the LED blinks red.Adobe PDF Library 16.0.3 Adobe InDesign 17.0 (Macintosh)