STC-3028 Temperature Humidity Controller

1. Overview

With clear LED display for better readability.
Temperature and humidity control output.
Very easy to set temperature and humidity.
All parameters setting can be saved after short circuit.

2. Specifications

Power Supply: 110V-220VAC
Temperature control range: -20℃ ~ 80℃
Humidity control range: 1 ~ 99%RH
Control accuracy: ±1℃/±1%RH
Sensor: temperature humidity sensor
Output: Max 10A

3. Wiring Diagram

A diagram shows the wiring for the STC-3028 controller. It illustrates connections for power supply (110/220V AC, with L and N terminals), a humidity sensor, and another power supply (12V DC/72V DC or 110VAC/220VAC) connected to the device.

4. Key Instruction

[Up Arrow]: increase value of start temperature
[Down Arrow]: decrease value of stop temperature
[Up Arrow]: increase value of start humidity
[Down Arrow]: decrease value of stop humidity

A diagram shows the controller's interface with buttons labeled [Up Arrow], [Down Arrow], and [Set/Mode].

5. Key Operation Instruction

Temperature Setting:

In normal working status, the left LED displays the real-time temperature. Press the [Up Arrow] key once. The red LED displays the start temperature. Press the [Down Arrow] key once. The red LED displays the stop temperature.
Hold the [Up Arrow] key for 3s. The LED flashes. Press the [Up Arrow] or [Down Arrow] key to change the start temperature.
Hold the [Down Arrow] key for 3s. The LED flashes. Press the [Up Arrow] or [Down Arrow] key to change the stop temperature.

Humidity Setting:

In normal working status, the right blue screen displays the real-time humidity. Press the [Up Arrow] key once. The red LED displays the start humidity. Press the [Down Arrow] key once. The blue LED displays the stop humidity.
Hold the [Up Arrow] key for 3s. The LED flashes. Press the [Up Arrow] or [Down Arrow] key to change the start humidity.
Hold the [Down Arrow] key for 3s. The LED flashes. Press the [Up Arrow] or [Down Arrow] key to change the stop humidity.

6. Operation Instruction

Cooling Mode:

When set start temperature is greater than or equal to stop temperature, the controller will work in cooling mode. A cooler can be used as the load. For example, set start temperature to 35°C and stop temperature to 32°C. The cooler works when the temperature is ≥ 35°C and stops when the temperature is ≤ 32°C.

Heating Mode:

When set start temperature is less than or equal to stop temperature, the controller will work in heating mode. A heater can be used as the load. For example, set start temperature to 45°C and stop temperature to 60°C. The heater stops when the temperature is ≥ 60°C and works when the temperature is ≤ 45°C.

Dehumidification Mode:

When set start humidity is greater than or equal to stop humidity, the controller will work in dehumidification mode. A dehumidifier can be used as the load. For example, set start humidity to 35%RH and stop humidity to 15%RH. The dehumidifier works when the humidity is ≥ 35%RH and stops when the humidity is ≤ 15%RH.

Humidification Mode:

When set start humidity is less than or equal to stop humidity, the controller will work in humidification mode. A humidifier can be used as the load. For example, set start humidity to 45%RH and stop humidity to 60%RH. The humidifier stops when the humidity is ≥ 60%RH and works when the humidity is ≤ 45%RH.

Reset:

In normal working status, hold the [Up Arrow] and [Down Arrow] keys. The two screens will display '888' to reset the controller.

Temperature and Humidity Calibration:

In normal working status, hold the [Up Arrow] and [Down Arrow] keys for 2 seconds to enter calibration mode of temperature. Press the [Up Arrow] or [Down Arrow] key to set the value between -30 and 30.
In normal working status, hold the [Up Arrow] and [Down Arrow] keys for 2 seconds to enter calibration mode of humidity. Press the [Up Arrow] or [Down Arrow] key to set the value between -30 and 30.
For example, if the tested temperature displays 25°C, but the real temperature is 30°C, if we set the value to 5, the tested temperature will change to display 30°C (25°C + 5°C). If we set the value to -5, the tested temperature will change to display 20°C (25°C - 5°C).

	Aideepen SHT-2000 Temperature and Humidity Controller Manual Comprehensive guide for the Aideepen SHT-2000 Temperature and Humidity Controller. Details main functions, technical specifications, heating/cooling and humidification/dehumidification settings, wiring diagrams, error codes, and safety precautions.
	W3002 Microcomputer Temperature Controller User Manual User manual for the W3002 Microcomputer Temperature Controller by Aideepen. Provides detailed instructions on parameter settings (P0, P1, P2, P3), heating and refrigeration modes, usage examples, common faults, and factory reset procedures.
	Aideepen 1200W 20A DC-DC Boost Converter Module: Specifications and Guide Detailed specifications, usage guide, and troubleshooting for the Aideepen 1200W 20A DC-DC Boost Converter Module, an adjustable voltage power supply module operating from 8-60V to 12-83V.
	SWM-103 Spot Welder Control Module: Instruction Manual Comprehensive instruction manual for the Aideepen SWM-103 spot welder control module, featuring double pulse trigger, voltage compensation, and parameter storage for DIY battery welding applications.