ELECTRIC BICYCLE USER MANUAL

Accessories

• User manual
• Tool kit
• Key
• Charge
• Saddle
• Pedal
• Handlebar assembly

LIGHT-P4 Folding E-Bike

Please carefully check whether the items in the packaging box are complete and intact. If there are any missing or damaged items, please consult your dealer.

Product Specifications

Parts Description

• Saddle
• Seat Clamp
• Rear Rack
• Pedal
• Gear Shifter
• Kick stand
• Folding Instructions
• Display
• Bell
• Folding stem
• Handlebar folding latch
• LED light
• Frame folding latch
• Front fork
• Front disc brake
• Reflector panel
• Rear reflector
• Battery pack
• Hub motor

Folding Instructions

Follow these steps to fold the LIGHT-P4 Folding E-Bike:

1. While the e-bike is powered off, lower the seat to the lowest position.
2. With the folding latch open, rotate the stem downward.
3. Fold the pedals, retract the kickstand, and rotate the front frame folding latch outward to open it.
4. Fold and rotate the front frame, ensuring the magnetic clasp between the front and rear wheels engages to prevent movement.

Warning: Before folding the front frame, remove the key from the battery switch hole to prevent it from breaking during folding.

Assembly Instructions

1. Remove all items from the packaging box and take off the protective foam from the bike and accessories.
2. Unfold the bike frame, rotate the folding latch toward the frame, and firmly lock it in place.
3. Check if the latch is securely fastened and lower the kickstand.
4. Stand the stem upright and rotate the folding latch inward to lock it securely.

Saddle Clamp Adjustment

1. Install the saddle by rotating the seat clamp outward, then inserting the saddle post into the seat tube.
2. Lock the folding latch inward and check if the saddle is stable.

Pedal Assembly Procedure

Install the pedals, ensuring proper left (L) and right (R) identification. Tighten the right pedal clockwise and the left pedal counterclockwise.

Battery Removal Method

1. Push the button in the indicated direction.
2. Open the battery compartment cover.
3. Rotate the seat to an appropriate angle to facilitate taking out the battery.
4. Turn off the power and unplug the battery.
5. Insert the key into the battery lock and turn to the right.
6. Lift using the handle of the battery and pull up along the direction of the battery compartment.

How to Charge

Due to battery self-consumption during transportation and storage, it is normal for the battery to be low or empty when used for the first time. Please charge according to the following charging steps. You can choose from the two ways for charging: charging the battery in your e-bike or removing it to charge it separately. Do not allow minors to use the charging equipment.

Charging the battery in your e-bike:

1. Open the battery box cover and remove the rubber cover from the charging port.
2. Plug the charger into a power outlet, then connect the output end of the charger to the vehicle's charging port.
3. After charging is complete, be sure to close the rubber cover.

Remove battery to charge:

1. Remove the battery from the battery compartment and open the rubber plug on the charging port.
2. Plug the charger into a power outlet, then connect the output end of the charger to the vehicle's charging port.
3. After charging is complete, make sure to close the rubber cover.

Note: The red light of the charger indicates the battery is charging. The green light indicates the battery is charged. Please turn off the power after the battery is fully charged. If the temperature of the e-bike body exceeds 40°C, the battery will not be charged normally. Please wait until it drops below 40°C before charging.

Controls and Display

Head Combination Switch

• Plus Button (+): Short press to switch data display style; Long press to turn on/off the e-bike light switch.
• Minus Button (-): Short press to switch between Boost gear and Power-down gear; Long press for Standby Settings, Wheel Diameter Settings, Speed Limit Settings, Backlight Settings, Unit Settings, Trip Reset.
• Type-C Port: Charging port.

Display Information

• Headlight: Indicates if the headlight is on.
• Assist Mode: Shows the current assist level (e.g., Gear Levels 1-3).
• Real-Time Speed: Displays current speed (e.g., 23.Km/h).
• Battery Level: Shows remaining battery percentage (e.g., 86%).
• Trip Distance: Displays the distance traveled (e.g., TRIP 160.3 KM).
• Riding Time: Shows the duration of the current ride (e.g., RUN TM 00:00:00).

Frame and Motor Codes

The motor code number is engraved on the end cover of the motor. The frame number location is shown in the figure.

[Description of motor code location: The number is engraved on the end cover of the motor.]

[Description of frame number location: The location of the frame number is shown in the figure.]

Error Code Meaning Sheet

Warning Codes

Error Codes (Decimal)

Note: Some error codes unrelated to this vehicle are not listed.