Hikvision DS-KH6320-WTE1 Network Indoor Station

Product Overview

The Hikvision KH6 series IP indoor station features a 7-inch touch screen for fluent video and audio communication. It is designed for easy deployment, allowing for independent setup of the entire video intercom system, reducing installation time and cost. Users can view, chat with, and grant access to visitors remotely via mobile phone. The device also integrates with other control systems such as CCTV and elevator control.

Key Features:

• 7-inch TFT touch screen with 1024 x 600 resolution
• Convenient Hik-Connect APP Mobile Control
• Remote call reception, door opening, and live view
• Easy to use without a PC
• Wizard for quick setup
• System configuration via the touch screen
• Live view of door stations and public area cameras
• Support for voice messages when no response
• Alarm system linkage for timely notification
• Elevator access control integration

Diagram References and Installation

1. Appearance

The device features the following components:

• ① Screen ?️
• ② Microphone ?
• ③ Debugging Port ? (for debugging only)
• ④ Network Interface ?
• ⑤ Loudspeaker ?
• ⑥ TF Card Slot ?
• ⑦ Alarm Terminal ?
• ⑧ Reserved ?
• ⑨ Power Terminal ?

Note: Device appearance may vary by model. Refer to the actual device for details.

2. Terminal and Wiring

The rear panel terminal has 20 pins, including:

• 2 RS-485 pins
• 5 Reserved pins
• 4 Relay output pins
• 8 Alarm input pins
• 1 GND pin

Note: The DS-KH6320-TE1 model has 11 reserved pins, 8 alarm input pins, and 1 GND pin.

Wiring Diagram Description: A diagram illustrates connections for RS-485 (Red RS-485+, Red RS-485-), Relay Output (White NO2, Black NC2, Black COM1), and Alarm Input (Black AIN8 down to White AIN1, White GND). Specific wire colors are mapped to functions.

3. Installation

The indoor station supports wall mounting with two modes:

Installation Accessory Description

Required accessories include a wall mounting plate and a junction box. The junction box dimensions should be 75 mm (width) x 75 mm (length) x 50 mm (depth). The wall mounting plate dimensions are shown in a diagram.

Before You Start

• Ensure the device and all parts are in good condition.
• The device supports 12 VDC power supply; verify compatibility.
• Power off all related equipment before installation.
• Check product specifications for the installation environment.

Wall Mounting with Junction Box

1. Chisel a hole in the wall: 76 mm (width) x 76 mm (length) x 50 mm (depth).
2. Insert the junction box into the chiseled hole.
3. Fix the wall mounting plate to the junction box using 2 screws [screw].
4. Hook the indoor station onto the wall mounting plate by aligning the plate hooks with the slots on the rear panel. Ensure the lock catch [lock catch] engages automatically.

Wall Mounting without Junction Box

1. Insert 2 expansion tubes into the wall.
2. Fix the wall mounting plate to the wall using 2 screws [screw].
3. Hook the indoor station onto the wall mounting plate by aligning the plate hooks with the slots on the rear panel. Ensure the lock catch [lock catch] engages automatically.

Diagrams illustrate the dimensions of the junction box and wall mounting plate, and step-by-step visuals for both wall mounting methods, showing the placement of the junction box [junction box], wall [wall], wall mounting plate, screws [screw], and the indoor station's rear panel with hooks [hook] and lock catches [lock catch].

Getting Started

1. Activate Indoor Station

You must activate the device by setting a strong password before use.

1. Power on the device; it will automatically enter the activation page.
2. Create and confirm a password.
3. Tap OK to activate the indoor station.

2. Quick Configuration

1. Choose the language and tap Next.
2. Set network parameters and tap Next:
   • Edit Local IP, Subnet Mask, and Gateway parameters, or enable DHCP for automatic network configuration.
3. Configure indoor station parameters:
   • Select Indoor Station and tap Next to link the main door station. Edit Floor and Room No., and create/confirm the SIP register password. (Note: The SIP password must match the door station's registration password).
   • Tap Advanced Settings to edit Community No., Building No., and Unit No.
   • Optionally, enable Indoor Station Settings and select the indoor station to link.
   • Select Indoor Extension and tap Next to link an indoor station. Edit No. and Room Name, and create/confirm the SIP register password.
4. Link related devices and tap Next. If devices are on the same LAN, they will appear in a list. Tap a device or enter its serial number to link.
   • Tap the settings icon to access Network Settings.
   • Edit door station network parameters manually or enable DHCP.
   • Tap OK to save settings.
5. Tap Finish to save all settings.

Refer to the Video Intercom Network Indoor Station Configuration Guide and Operation Guide for detailed information (QR codes in original document are excluded).

Specifications

System Parameters

Display Parameters

Video Parameters

Audio Parameters

Capacity

Network Parameters

Device Interfaces

General

Available Model

• DS-KH6320-WTE1

Dimension Diagram Description

A diagram shows the front, side, and rear views of the indoor station with dimensions: 200 mm (7.87") width, 140 mm (5.51") height, and 15.1 mm (0.92") depth.

Optional Accessories