Maxcom mRing MR100 Smart Ring

Getting Started

Follow these steps for initial setup and use of your Maxcom mRing MR100 smart ring.

1. Charging: Before first use, charge the smart ring using the included cable. A red LED indicates charging; a green LED illuminates when fully charged.
2. App Installation: Download and install the control application on your smartphone. You can do this by:
   • Scanning the QR code [QR Code: Scan to download the AIZO RING app]
   • Searching for the "AIZO RING" app in the Google Play Store or Apple App Store.
3. Phone Setup: Enable the following on your phone:
   • Bluetooth and GPS location (for Android phones)
   • Bluetooth (for iOS phones)
4. App Permissions: During installation, grant the application necessary permissions to operate in the background and access phone resources like location and notifications.
5. Device Connection: Tap the top right corner of the app screen and select "add". Search for "mRing MR100" in the list of available devices. Note: The smart ring must be connected to charging when first connecting to the phone. During pairing, the ring will flash green for 5 seconds.
6. Profile Setup: Enter your age, weight, and height in the app. Daily activity goals can be configured in the "activity management" section.

Wearing Methods

For accurate measurements, place the sensors inside your finger. It is recommended to wear the ring on the index, middle, or ring finger for optimal data monitoring.

Troubleshooting Connection Problems

If you encounter connection issues, try the following:

1. Ensure Bluetooth is turned on and your phone is visible to other devices.
2. Ensure GPS/location services are enabled (for Android phones).
3. Verify the app has been installed with all necessary permissions for background operation.
4. Connect the smart ring to charge before attempting the first connection.
5. Ensure you are connecting to the smart ring FROM THE APP LEVEL.

If unsuccessful, further steps include:

1. Check if the phone has GPS enabled.
2. Navigate to phone settings > Applications and notifications > Application permissions > allow background operation and notifications.
3. Check if the smart ring is already connected via the phone's Bluetooth menu. If so, go to the BT menu, "forget device", and then reconnect via the app.

Technical Information

Maximum EIRP: 0.79 dBm

Environmental Protection Information

Note: This device is marked in accordance with European Directive 2012/19/EU and the Polish Act on waste electrical and electronic equipment. The symbol of a crossed-out waste container [Symbol: Crossed-out waste container] indicates that this equipment must not be disposed of with household waste after its period of use. The product should be disposed of through selective collection at designated points. Proper handling of waste electrical and electronic equipment helps prevent negative consequences for human health and the environment. The set includes a Li-ion battery. Used batteries are harmful to the environment and must be stored and disposed of at designated collection points, not as municipal waste. DO NOT THROW BATTERIES OR ACCUMULARS INTO FIRE!

Warranty Terms

Maxcom S.A., with headquarters in Tychy, Poland, grants a 24-month warranty for the proper operation of the purchased device (Product). The warranty is valid with proof of purchase. Damage from improper use, electrostatic discharge, or mechanical damage is not covered. Self-repair or modification will void the warranty. For repairs, contact an authorized service center or the seller. Maxcom is not responsible for defects caused by improper use or non-compliance with instructions.

Device Care: Protect the device against crushing, impact, and dropping. Clean the surface with a soft, clean, and dry cloth. Do not paint the device, as paint may interfere with operation. The device may heat up during prolonged use or charging; this is normal. To avoid overheating, slow down operations, close applications, stop charging, or turn off the device.

Manufacturer Notes

The manufacturer is not responsible for consequences due to incorrect use, abuse, or failure to follow instructions. This manual is for informational purposes only. Features may vary by software and country. Maxcom reserves the right to make changes without notice.

SIMPLIFIED EU DECLARATION OF CONFORMITY

Maxcom S.A. declares that the radio equipment model "mRing MR100" complies with Directive 2014/53/EU (RED) and Directive 2011/65/EU (RoHS).

The full text of the EU declaration of conformity is available at: http://www.maxcom.pl/deklaracje