IFROGZ Airtime™ Pro 2 SE Truly Wireless Earbuds

Introduction

Welcome to truly wireless audio with 25 hours* of combined battery life and a wireless charging case.

Simple Pairing

Follow these steps to pair your earbuds:

1. Remove earbuds from the case and remove the protective cover from the charging contacts. Place earbuds in the charging case and allow 5 minutes to charge before first use.
2. Open the case and remove the earbuds to initiate Bluetooth® pairing.
3. On your device's Bluetooth menu, select "IFROGZ Airtime Pro 2 SE" to connect.

Touch Controls

The Airtime Pro 2 SE earbuds feature built-in touch controls. Tap on the end of the earbud (on the IFROGZ logo) to navigate:

• Quick tap: Play/pause audio, answer/end calls.
• 2x taps: Skip to the next track.
• Long hold: Play previous track, reject incoming calls.
• 3x Taps: Activate your device's voice assistant.

Using the Earbuds

Turning Earbuds On/Off

To turn the earbuds on, simply remove them from the case. To turn them off, return them to the case. The earbuds will enter hibernation mode if not used for 20 minutes.

Getting the Best Fit

For optimal sound quality, ensure a good seal with the correct ear tip size. IFROGZ provides different-sized tips. If an ear tip feels loose, try a larger size. If you experience too much pressure or the tip doesn't fit comfortably, try a smaller size. Note that each ear may require a different size tip.

To test the fit, perform the yawn test: insert the earbuds and yawn. If they remain secure and the seal is maintained, you have a good fit.

Charging

Charging the Wireless Earbuds

The charging case provides enough power to charge the earbuds up to 4 times*. Place the earbuds into the charging case; they will magnetically click into place. A red light on the earbuds indicates they are charging.

Charging the Case

The case arrives pre-charged. Recharge it wirelessly using a compatible wireless charging pad or manually via the included USB-C cable.

Wireless Charging

1. Place the charging case on a compatible wireless charging pad.
2. The Battery Indicator lights on the front of the case will flash to show the current battery level, indicating charging is in progress. All four lights will turn off when the case is fully charged.

Manual Charging

1. Connect the included USB-C charging cable to the port on the side of the case.
2. Connect the USB-A end of the cable to a 5V USB power source.
3. The Battery Indicator light will flash to show the current battery level. All four lights will illuminate and then turn off when the case is fully charged.
4. Disconnect the charging cable.

Quick Charge Feature

Nest the earbuds in the charging case for ten minutes to gain an additional hour of playtime.

Checking the Battery Level

The case holds enough power for approximately 4 full charges of the earbuds, totaling up to 25 hours of playback. To check the case's remaining battery level, place the earbuds inside. The LED on the front of the case will illuminate:

• Four lights illuminated: 75% or more battery remaining.
• Three lights illuminated: 50-74% battery remaining.
• Two lights illuminated: 25-49% battery remaining.
• One light illuminated: Less than 24% battery remaining.

Factory Reset

If you encounter functionality issues, performing a factory reset can help. Follow these steps:

1. Place both earbuds in the charging case.
2. Reset the right bud:
   • Remove the right bud from the case.
   • Tap and hold for 10 seconds until the light flashes red and then turns off.
   • Wait 10 seconds after the red flashing light.
   • Tap and hold for five seconds until the light turns on and flashes red and white.
   • Quickly tap the bud six times; the light will turn off.
   • Return the bud to the case.
3. Reset the left bud: Repeat the steps above for the right bud.
4. Connect the earbuds: Remove both earbuds from the case and allow them to connect to each other for approximately five seconds. They will flash red and white, indicating pairing mode.
5. The earbuds are now reset to factory settings. You must remove the previous pairing from your device's Bluetooth settings. After removal, follow the initial pairing instructions in this guide.

Troubleshooting and Support

For any assistance, IFROGZ customer support is available:

• Online: www.support.zagg.com
• Phone: 1-800-700-9244

Technical Specifications

• Drivers: 6mm
• Resistance: 16 Ohms ± 15%
• Sensitivity: 100dB ± 3dB
• Frequency: 50Hz - 20KHz
• Working Time: 5+20hrs
• Charging Time: 1.5-2h

Compliance Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Legal and Warranty Information

Warranty information is available at www.zagg.com/warranty-policies.

©2020 ZAGG Inc. All Rights Reserved | NASDAQ: ZAGG | MADE IN CHINA.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ZAGG Inc is under license. USB-C® is a trademark of USB Implementers Forum. Other trademarks are property of ZAGG.

*All hours usage and charging claims are estimates based on internal testing and will vary based on individual usage.

Model Number: 314-00849