Quick Start Guide
DeviceSupport – ThirdReality
User Guide for THIRDREALITY models including: 3RSNL02043Z, 3RSNL02043Z Multi Function Night Light, Multi Function Night Light, Function Night Light, Night Light, Light
3RSNL02043Z User Guide (PDF) THIRDREALITY Third Reality, Inc THIRDREALITY,Multi-Function,Night,Light,,Zigbee,Repeater,,3-in-1,Combines,a,Motion,Sensor,,a,Illumination,Sensor,and,RGB,Color,Night,Light,,1-100%,Adjustable,Brightness,,Zigbee,hub,Required,,
THIRDREALITY Multi-Function Night Light, Zigbee Repeater, 3-in-1 Combines a Motion Sensor, a Illumination Sensor and RGB Color Night Light, 1-100% Adjustable Brightness, Zigbee hub Required - Amazon.com
File Info : application/pdf, 2 Pages, 8.08MB
DocumentDocumentMulti-Function Night Light Quick Start Guide Product Overview Third Reality Zigbee Multi-Function Night Light - a compact and intelligent solution combines a motion sensor, a light sensor and color night light. With remote control via Zigbee commands, it offers versatile automation options for security, lighting, and ambiance. Experience convenience and innovation in one device. Note: The level of illuminance value is defined with reference to the lux value, not exactly the same. What's In The Box Multi-Function Night Light × 1 Power Adapter × 1 Quick Start Guide × 1 Product Details USB Interface Color Night Light Illumination Sensor Set Pinhole Motion Sensor Power Adapter Specification Dimension Color Input Material 2.6 x 1.6 x 2.5 inches White DC 5V 0.5A Plastic LED Status Table A: BOOTUP LED Status LED Color Scheme Comments First Blink Green is Local Routine Enabled Red is Local Routine Disabled Short press the pin hole will change the Local Routine Setup Status Second Blink Yellow is not paired Warm White is paired Long press the pin hole will reset the pairing status Status Check Not Paired: On <=5s is illumination > min On >5s is illumination <=min Illumination > min means environment is light need to turn off automaticlly Illumination <= min means environment is dark need to keep on and then Paired: check report Status (First paired - Default blue on and dim 2 times) If paired then go to RUNTIME status B: Connect/Disconnect LED Status LED Color Scheme Comments Two Times If LED is ON, dim two times (previous color) is indicate from disconnect to connect If LED is Off, No Indication The device will automatically Try reconnect Three Times If LED is ON, dim three times (previous color) is indicate from connect to disconnect If LED is Off, No Indication Long time has not been reconnected Try restarting your device or Hub Setup 1. Plug the night light into a power outlet using a USB-A power adaptor, it initially lights up green and turns yellow, indicating it is in pairing mode. Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold the reset button through the pinhole for 5 seconds until it turns red, then release, the device will be reset and re-enter pairing mode.) 2. Install the Zigbee hub & app on your device and log in, make sure the firmwares are up to date, and follow the instructions to set up the device. 3. Once the pairing is successfully completed, the night light dims in blue twice then turn solid blue. You can change its brightness and color in the app. 4. The motion sensor, illumination sensor, and color light of the multi-function night light will report their status information as individual sub-devices, faciliating the configuration of various routines and home automation tasks. Local Routine The product supports local routines where the light will turn on when both the illumination sensor and motion sensor meet the specified conditions When the light is dim and detects human motion. Short press the reset button through the pinhole to enable or disable the local routine function. Pressing the button once and seeing a green light indicates that the feature is currently enabled. Pressing the button again and seeing a red light indicates that the routine is disabled. In both enabled and disabled states, motion sensor, illumination sensor, and color light will be reported synchronously. Note that if you turn your Multi-Function Night Light on or off using your app or voice, Local Routine will be disabled for 12 hours. Pairing with Different Hubs Before pairing, use a pin to press into the pinhole and hold for 5 seconds until the LED turns red, then release to set the Multi-Function Night Light into pairing mode; Make sure the your hub's firmware and phone apps are up to date. Pairing with Third Reality Hub: Third Reality Hub Gen2 Plus App: Third Reality Pairing steps: 1. Tab "+" in Third Reality App, follow the on-screen instructions to add Smart Hub Gen2 Plus. 2. Tab "+" in the right of Smart Hub Gen2 Plus to add device, it will be added within seconds. 3. Create routines to use the motion sensor of the Multi-Function Night Light to control other connected devices. Pairing With Amazon Echo Hub: Echo speakers with built-in Zigbee hub, Echo 4th Gen, Echo Plus 1st & 2nd Gen, Echo Show 10 2nd & 3rd Gen, Echo Studio App: Amazon Alexa Pairing steps: 1. Tab "+" in the Alexa App, choose "Zigbee" and "others" to add device, the Multi-Function Night Light will be added as the "First Light". 2. You can create routines with the "First Light". Pairing With Hubitat Website: http://find.hubitat.com/ Pairing steps: 1. Tab "Add Device" in Hubitat Devices page. 2. Choose "Zigbee", then "Start Zigbee Pairing". 3. Type in a device and room name and click "Next" to complete pairing. Pairing With Home Assistant Pairing steps: Zigbee Home Automation(ZHA) Zigbee2MQTT Pairing With SmartThings Hub: SmartThings Hub 2015/SmartThings Hub 2018/ Aeotec Smart Home Hub App: SmartThings APP Pairing steps: 1. Tab "Add device" in the up right in your SmartThings App. 2. Tab "Scan for Nearby devices" and choose the hub to pair the light to. 3. The light will be paired successfully, then you can create routines with it. FCC regulatory conformance This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help important announcement. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Limited Warranty For limited warranty, please visit www.3reality.com/devicesupport For customer support, please contact us at info@3reality.com or visit www.3reality.com For help and troubleshooting related to Amazon Alexa, visit the Alexa app.