sonoff.tech/usermanuals
for SONOFF models including: MINIR4 V1.1, MINI Extreme WiFi Smart Switch, MINI Extreme Switch, WiFi Smart Switch, Switch, MINI Switch, Extreme Switch, WiFi Switch, Smart Switch
This device complies with RSS-247 of Industry Canada. ... L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme.
il y a 1 jour — 本表格依据SJ/T 11364 的规定编制： o：表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572规定的限量要求以下； x：表示该有害物质至少在该部件的某一均质 ...
File Info : application/pdf, 19 Pages, 2.87MB
DocumentDocumentMINI Extreme
Wi-Fi Smart Switch
· ----------1 - 7
· English ----------8 - 14 · Warning ----------15 - 16
1Kg2
1
MINI Extreme10A
/
1.
2
2.
MINIR4 10A (MCB) (RCBO) 1. S1S2 App 2. S1S2, 3.
App
1. App
Google Play StoreApple App Store""
3
2.
""
105
3.
""App, "+". "" App
4
eWeLink App """"
0/8
MINI Extreme
5
Wi-Fi
MINIR4 100-240V ~ 50/60Hz 10A Max 100-240V ~ 50/60Hz 10A Max 2400W IEEE 802.11b/g/n 2.4GHz -10 ~ 40 5%-95%RH, PC V0 39.5x33x16.8mm
GB/T 16915.2-2012
(Pb)
(Hg)
(Cd)
(Cr VI (PBB)
(PBDE)
o
o
o
o
o
o
x
o
o
o
o
o
o
o
o
o
o
o
PCB
o
o
o
o
o
o
SJ/T 11364
oGB/T 26572 xGB/T 26572
6
eWeLink App "WiFi"
eWeLink App ""
1. Wi-FiApp
1. 10 2 Wi-Fi "" 3Wi-Fi2.4GHz 4Wi-Fi 5
2. LED
1 2
APP"&"
3. Wi-Fi""
1 2Wi-Fi 3Wi-Fi Wi-Fi 4 5Wi-Fi
7
Product introduction
English
Button Network indicator
Wiring ports
The device weight is less than 1kg, and the recommended installation height is less than 2m.
Instruction of LED indicator status
LED indicator status
Blue LED indicator flashes (one long and two short)
Status instruction Pairing mode
Blue LED indicator keeps on
Device is online
8
English
Features
MINI Extreme is compact and tiny enough to be installed in the mounted box, and it supports loads of up to 10A, enable to transform your ordinary switch into a smart switch. Safe and smart, allows you to set smart scenes with other smart devices to automate your home.
Remote Control
Timer Schedule
Voice Control
LAN Control
Power-on State
Inching Mode
Installation
1. Power off
Smart Scene
Group Control
Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!
9
2. Wiring instruction
English
To ensure the safety of your electrical installation, it's essential either a Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating of 10A has been installed before the MINIR4. 1aNo matter S1 and S2 are connected or left idle to the external switch, this device canbe controlled by automation or the App. 2aIt is prohibited to connect S1 and S2 terminals to the neutral or ground wire, in order to avoid damaging the equipment and causing danger. 3aMake sure all wires are connected correctly.
Pair with eWeLink App
1. Download the eWeLink App
Please download the "eWeLink" App from Google Play Store or Apple App Store.
10
English
2. Power on
After powering on, the device will enter the Pairing Mode defaulted during the first use, and the Network indicator flashes in a cycle of two short and one long.
The device will exit the Pairing Mode if not been paired within 10mins. If you want to enter this mode again, please long press the button for 5s until the Network indicator flashes in a cycle of two short and one long and then release.
3.Add device
Open the eWeLink App, Tap "+" and select "Add Device", then operate following the prompt on the App.
It's required to turn on the Bluetooth on your Phone when adding a device. 11
English
Add eWeLink-Remote Sub-devices
Enter the Device Settings page on the eWeLink App, select "eWeLink-Remote sub-devices" and tap "Add", then trigger the sub-device to add it successfully.
Install the MINI Extreme in the mounting box
12
Specifications
Model Input Output Max. power Wi-Fi Working temperature Working humidity Casing material Dimension
MINIR4 100-240V ~ 50/60Hz 10A Max 100-240V ~ 50/60Hz 10A Max 2400W IEEE 802.11b/g/n 2.4GHz -10 ~ 40 5%-95% RH, non-condensing PC V0 39.5x33x16.8mm
English
Device Network Changing
Change the device's network by "Wi-Fi Settings" in the "Device Settings" page on the eWeLink App.
Factory Reset
Reset the device to factory settings by "Delete device" on the eWeLink App.
FAQ (Frequently Asked Questions)
1. Fail to pair Wi-Fi devices with the eWeLink App
1aMake sure the device is in pairing mode. The device will automatically exit the pairing mode if it is not paired within 10mins. 2aPlease enable location service and allow access to location permission. Before connecting Wi-Fi network, please enable the location service and allow access to the location permission. Location information permission is used to obtain Wi-Fi list information, if you "disable" the location service, the device cannot be paired.
13
English
3aMake sure your Wi-Fi works on 2.4GHz band. 4aMake sure to enter the Wi-Fi SSID and password correctly without special characters. Incorrect password is a common cause of pairing failure. 5aTo ensure good signal transmission while pairing, please place the device close to the router.
2. The LED indicator flashes twice on repeated means the server fails to connect.
1aMake sure the networking is normal. Check the internet works well by connecting your phone or PC. If fail to connect, please check the availability of the Internet connection. 2.aWith the low load capacity of the router, the connected devices exceed the router's maximum load capacity. Please check the maximum number of devices that your router can carry, if the connected devices exceed the maximum value, remove some devices or use a higher load capacity router.
If the above methods cannot help to solve the problem, please submit your problem to "Help & Feedback" on the eWeLink App.
3. Wi-Fi devices are "offline"
1aDevices fail to connect to the router. 2aEntered the wrong Wi-Fi SSID and password. 3aWi-Fi SSID and password contain special characters, for example, our system can't recognize Hebrew and Arabic characters, which causes Wi-Fi connections to fail. 4aLow capacity of the router. 5aWi-Fi signal is weak. The router and the devices are too far apart, or there is an obstacle between the router and the device, which prevents the signal from being transmitted.
14
Warning
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for
help.
FCC Radiation Exposure statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
15
Warning
ISED Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)L'appareil ne doit pas produire de brouillage; (2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet appareil numérique de la Classe B conforme à la norme NMB-003 du Canada. Cet appareil est conforme à la norme RSS-247 d'Industrie Canada. Le fonctionnement est soumis à la condition que cet appareil ne provoque pas d'interférences nuisibles.
ISED Radiation Exposure Statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition aux rayonnements de la ISED établies pour unenvironnement non contrôé. Cet équipement doit être installé et fonctionner à au moins 20cm de distance d'un radiateur ou de votre corps. Cet émetteur ne doit pas être co-localisé ou fonctionner en conjonction avec une autre antenne ou un autre émetteur.
16
Warning
SAR Warning
Under normal use of condition, this equipment should be kept a separation distance of at least 20cm between the antenna and the body of the user. Dans des conditions normales d'utilisation, cet équipement doit être maintenu à une distance d'au moins 20 cm entre l'antenne et le corps de l'utilisateur.
WEEE Warning
WEEE Disposal and Recycling Information All products bearing this symbol are waste electrical and electronic equipment (WEEEas in directive 2012/19/EU) which should not be mixed with unsorted householdwaste. Instead, you should protect human health and the environment by handingover your waste equipment to a designated collection point for the recycling of waste electricaland electronic equipment, appointed by the government or local authorities. Correct disposaland recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about thelocation as well as terms and conditions of such collection points.
EU Declaration of Conformity
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type MINIR4 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://sonoff.tech/usermanuals
Scatola
Manuale
Neto
PAP 21
PAP 22
EVA 7
Carta
Carta
Plastica
RACCOLTA DIFFERENZIATA
Verifica le disposizioni del tuo Comune. Separa le componenti e conferiscile in modo corretto.
17
For CE Frequency: Operation frequency Range: 2402-2480MHz(BLE) 2412-2472MHz(Wi-Fi)
RF Output Power: 1.87dBm(BLE) 16.12dBm(802.11b),15.80dBm(802.11g),15.67dBm(802.11n20), 13.33dBm(802.11n40)(Wi-Fi)
FR Cet appareil se recycle
À DÉPOSER À DÉPOSER EN MAGASIN EN DÉCHÈTERIE
OU