EK-Quantum Vector D-RGB Upgrade Kit

INSTALLATION MANUAL

This product is intended for installation by expert users only. Please consult with a qualified technician. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products or their installation. The following instructions are subject to change without notice. Please, read the manual carefully before beginning with the installation process.

Table of Content

Disconnect the LEDs
Replace the Stickout
Attaching the New Stickout and D-RGB LED
- PLEXI VERSION
- ACETAL VERSION
Attaching the D-RGB Terminal Cover
Important Information
Connecting the D-RGB LED Strip
Support and Service
Social Media

Disconnect the LEDs

First, disconnect the cable between the Terminal Cover and Stickout. After that, remove the Terminal Cover from the FC Terminal.

Replace the Stickout

Remove the Stickout from the water block and store the screws for later use.

Note: If you have the Acetal version of the water block, do not forget to remove the RGB LED from the Acetal part.

Diagram Description: An illustration shows the removal of the 'Stickout' and 'Stickout Screws' from a water block component labeled 'RTX 2080'.

Attaching the New Stickout and D-RGB LED

PLEXI VERSION

Take the Stickout and D-RGB LED from the box. Remove the protective foil from D-RGB LED and attach the LED to the Stickout. After this, use the stored screws to secure the Stickout to the Plexi part.

Diagram Description: An illustration shows the 'Stickout' and 'D-RGB LED' components being prepared for attachment to a 'Plexi' water block part.

ACETAL VERSION

Take the Stickout and D-RGB LED from the box. Remove the protective foil from D-RGB LED and attach the LED to the Acetal. D-RGB is oriented towards the Stickout. After this, use the stored screws to secure the Stickout to the Acetal part.

Diagram Description: An illustration shows the 'Stickout' and 'D-RGB LED' components being prepared for attachment to an 'Acetal' water block part, with the D-RGB oriented towards the Stickout.

Attaching the D-RGB Terminal Cover

Take the pre-assembled D-RGB Terminal Cover from the box and attach it to the FC Terminal.

Diagram Description: An illustration shows the D-RGB Terminal Cover being attached to the FC Terminal of the water block.

Important Information

Do not forget to connect the D-RGB LED cable of the Stickout to the cable of the Terminal Cover.

In case you have 2 (two) Stickouts: First, connect the Stickout cables and then you can connect them to the Terminal Cover cable!

Connecting the D-RGB LED Strip

Plug the 3-pin connector from the water block's D-RGB LED light into the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital.

Warning: Please ensure that the arrow indicated on the connector is plugged into the +5V line as indicated on your motherboard. If you connect the LED Diode to the 12V RGB HEADER you can damage the LEDs.

Diagram Description: An illustration shows the 3-pin connector of the D-RGB LED strip being plugged into the D-RGB Header on a motherboard. The illustration highlights the D-RGB Header and RGB Header on the motherboard.

Support and Service

For assistance please contact: http://support.ekwb.com/

EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU

	EK-Quantum Vector D-RGB Upgrade Kit Installation Manual Installation manual for the EK-Quantum Vector D-RGB Upgrade Kit, detailing steps for disconnecting LEDs, replacing stickouts, attaching new components, and connecting D-RGB LED strips for PC water cooling systems.
	EK-Quantum Vector D-RGB Upgrade Kit Installation Manual This manual provides step-by-step instructions for installing the EK-Quantum Vector D-RGB Upgrade Kit. It covers disconnecting LEDs, replacing the stickout, attaching the new stickout and D-RGB LED for both Plexi and Acetal versions, attaching the D-RGB terminal cover, and connecting the D-RGB LED strip to the motherboard. Important information regarding LED connection and potential damage is also included.
	EK-Quantum Vector D-RGB Upgrade Kit Installation Manual Detailed installation manual for the EK-Quantum Vector D-RGB Upgrade Kit, providing step-by-step instructions for connecting and installing D-RGB LED strips and terminal covers for PC water cooling systems.
	EK-Quantum Vector D-RGB Upgrade Kit Installation Manual This manual provides step-by-step instructions for installing the EK-Quantum Vector D-RGB Upgrade Kit. It covers disconnecting existing LEDs, replacing the stickout component, attaching the new D-RGB LED strip for both Plexi and Acetal versions of the water block, and connecting the terminal cover. The guide also includes crucial information regarding D-RGB LED strip connection to the motherboard and provides support and social media contact details for EK Water Blocks.
	EK-Quantum Momentum Aorus X570 Master D-RGB - Plexi Monoblock User Guide Comprehensive user guide for the EK-Quantum Momentum Aorus X570 Master D-RGB - Plexi monoblock, detailing installation, thermal pad placement, and D-RGB LED strip connection.
	EK-Quantum Vector RTX 3080/3090 D-RGB GPU Water Block User Guide User guide for the EK-Quantum Vector RTX 3080/3090 D-RGB GPU Water Block, detailing installation, preparation, and testing.
	EK-Vector RTX Aorus 2080 Ti Backplate Installation Manual \| EK Water Blocks This manual provides detailed, step-by-step instructions for installing the EK-Vector RTX Aorus 2080 Ti Backplate. It includes essential information on preparing the graphics card, applying thermal pads, attaching the backplate, important disclosures, and warranty details. Designed for expert users, this guide ensures proper installation for optimal performance.
	EK-Quantum Vector² Trio RTX 4080 D-RGB GPU Water Block User Guide Comprehensive user guide for the EK-Quantum Vector² Trio RTX 4080 D-RGB GPU water block, detailing installation steps, component lists, technical specifications, and warranty information.