Enbrighten Add-On Switch Installation Manual

Introduction

This manual provides instructions for installing the Enbrighten Add-On Switch (Model AS2005) to create a 3-way or more switch configuration. It is important to follow these instructions carefully. If you encounter difficulties or are unsure about your home wiring, consult a licensed electrician.

IMPORTANT! This add-on switch is not wireless enabled and must be used exclusively with one of the Enbrighten wireless devices. It is not designed for stand-alone use to control an electrical load. It does not have wireless functionality and does not act as a repeater in your wireless control network.

Tools You Will Need

• Screwdriver
• Pliers

Changing the Paddle Color (Optional)

Before installation, you can change the paddle color to match your decor.

1. Push the side tabs on one side, then the other, to release the paddle. Lift the cover up and off.
2. Place the new paddle onto the switch, aligning the side tabs, and snap it securely into place.

Wiring Instructions

WARNING — SHOCK HAZARD: Turn OFF the power to the branch circuit for the switch and lighting fixture at the service panel. All wiring connections must be made with the POWER OFF to avoid personal injury and/or damage to the switch.

This device is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada.

Step 1: Shut off power

1. Shut off power to the circuit at the circuit breaker or fuse box.
2. IMPORTANT! Verify power is OFF to the switch box before continuing.

Step 2: Remove existing switches

1. Remove both wallplates.
2. Remove the switch mounting screws.
3. Carefully remove the switch from each switch box location. DO NOT disconnect the wires yet.

Step 3: Identify switches and wires

• Line Switch (Primary Switch): Identify the switch connected to the fuse box. Label the wire connected to the common terminal “LINE.”
• Load Switch (Add-on Switch): Identify the switch connected to the lighting/fixture. Label the wire connected to the common terminal “LOAD.”

Step 4: Wiring the Line Switch (Primary Switch)

This involves replacing a standard switch with the Enbrighten primary switch.

1. Disconnect all wires on the existing switch.
2. Locate neutral wires inside the switch box (typically a bundle of white wires). Remove the wire nut securing them (A).
3. Connect the included jumper wire to the neutral wires and secure with a wire nut (A).
4. Connect the opposite end of the jumper wire to the NEUTRAL terminal on the primary switch (B).
5. Connect the wire labeled “LINE” to the LINE terminal on the primary switch (C).
6. Connect the ground wire (bare/copper/green) to the GROUND terminal on the primary switch (D).
7. Connect one of the two remaining wires (T1) to the LOAD terminal on the primary switch (E). Write down the color of this wire; you will need it for the add-on switch installation.
8. Connect the remaining wire (T2) to the TRAVELER terminal on the primary switch (F).

Step 5: Wiring the Load Switch (Add-on Switch)

This involves replacing a standard switch with the Enbrighten add-on switch.

1. Disconnect all wires on the existing switch.
2. Locate neutral wires inside the switch box (typically a bundle of white wires). Remove the wire nut securing them (AA).
3. Connect the included jumper wire to the neutral wires and secure with a wire nut (AA).
4. Connect the opposite end of the jumper wire to the NEUTRAL terminal on the add-on switch (BB).
5. Connect the ground wire (bare/copper/green) to the GROUND terminal on the add-on switch (CC).
6. Locate the wire color you noted in Step 4 (T1). Using a wire nut, secure it only to the wire connected to the “LOAD” terminal on the existing switch.
7. Connect the remaining wire to the TRAVELER terminal on the add-on switch (DD). This wire should be the same color as the wire connected to the TRAVELER terminal on the primary switch.

Step 6: Attach switches to boxes

1. Place both switches into their respective switch boxes, being careful not to pinch or crush wires.
2. Secure each switch to the box using the supplied screws.
3. Mount each switch wallplate.
4. Reapply power to the circuit at the fuse box or circuit breaker and test the system.

Specifications

• Model: AS2005
• Power: 120/277VAC, 60Hz
• Operating temperature range: 32-104° F (0-40° C)
• Type: Type 1 action
• Usage: For indoor use only

Specifications subject to change without notice due to continuing product improvement.

Important Safety Information

NOT FOR USE WITH MEDICAL OR LIFE-SUPPORT EQUIPMENT

SMART DEVICES SHOULD NEVER BE USED TO SUPPLY POWER TO OR CONTROL THE ON/OFF STATUS OF MEDICAL OR LIFE-SUPPORT EQUIPMENT.

RISK OF FIRE, RISK OF ELECTRICAL SHOCK, RISK OF BURNS

CAUTION:

• DO NOT EXCEED RATINGS
• DO NOT USE TO CONTROL ANY DEVICE WHERE UNINTENDED OPERATION COULD CAUSE UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
• DO NOT USE TO CONTROL RECEPTACLES
• FOR INDOOR USE ONLY

Warranty Information

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact Jasco Products Company's U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM – 8PM CT or visit www.byjasco.com if the unit should prove defective within the warranty period.

Contact and Support

If you have any problems or questions, contact Jasco Products Company's U.S.-based Consumer Care at 1-800-654-8483, option 1, Monday–Friday, 7AM–8PM CT.

For the most up-to-date product support, accessories, electronic (PDF) format manuals and more, visit www.byjasco.com/support.

Jasco Products Company LLC, Building B, 10 E. Memorial Rd. Oklahoma City, OK 73114.

Product Range

Enbrighten offers a variety of smart home devices, including:

• In-Wall Smart Dimmers
• Plug-in Smart Dimmers
• In-Wall Add-on Switches
• In-Wall Motion Switches or Dimmers
• Plug-in Smart Switches
• In-Wall Smart Switches
• Enbrighten Smart LED Bulbs
• In-Wall Smart Fan Controls
• Hinge Pin Smart Door Sensors
• Direct Wire, 40A Outdoor Smart Switches
• Portable Smart Multi Sensors
• In-Wall Tamper-Resistant Smart Outlets
• Plug-in Outdoor Smart Switches

Purchase additional items at ezzwave.com, ezzigbee.com or visit your local retailer.

To purchase an add-on switch or for more details, visit ezaddonswitch.com.

Multiple Paddle Colors Available: ezzwave.com/paddlecolors

Read It or Watch It

Read instructions or watch an easy-to-follow video. Scan QR code or visit goo.gl/BypXzF