If the light level in the room is not high enough, Presentation Mode may not ... the Maximum Message Length (MAX) is set to 60 characters; and the ...
Leitor Honeywell Granit 1991xi. O leitor de código de barras Granit 1991xi foi projetado para suportar as variadas demandas que existem em ambientes de ...
The Granit 1991xi is a robust, drop-resistant barcode reader designed for aggressive environments. Models include 1991iSR, 1991iXR, and 1991iXLR.
Leitor Honeywell Granit 1991xi
O leitor de código de barras Granit 1991xi foi projetado para suportar as variadas demandas que existem em ambientes de trabalho agressivos. Equipamento robusto e altamente resistente a quedas
bztech.com.br
GranitTM XP 199xi Series
Models: 1990iSR, 1990iXR, 1990iXLR, 1991iSR, 1991iXR, and 1991iXLR
Industrial Area-Imaging Scanners and Bases
User Guide
Disclaimer
Honeywell International Inc. ("HII") reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. HII makes no representation or warranties regarding the information provided in the publication. HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of software and/or hardware to achieve intended results. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of HII. Copyright 2022 Honeywell Group of Companies. All rights reserved. Web Address: sps.honeywell.com.
Trademarks
Microsoft® Windows® and the Windows logo are trademarks or registered trademarks of Microsoft Corporation. The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. Apple is a trademark of Apple Inc., registered in the U.S. and other countries. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners.
Patents
For patent information, refer to www.hsmpats.com.
TABLE OF CONTENTS
Customer Support ...................................................................................................................... xiii Technical Assistance ........................................................................................................... xiii Product Service and Repair .............................................................................................. xiii Limited Warranty .................................................................................................................. xiii
Chapter 1 - Get Started .................................................................................... 1
About This Manual......................................................................................................................... 1 Unpack Your Device....................................................................................................................... 1 Features of the Device.................................................................................................................. 2
1990i/1991i SR Features..................................................................................................... 2 1990i/1991i XR Features..................................................................................................... 2 1990i/1991i XLR Features .................................................................................................. 2 Connect a Corded Device............................................................................................................ 2 Connect with USB.................................................................................................................... 3 Connect with Keyboard Wedge .......................................................................................... 4 Connect with RS232 Serial Port ........................................................................................ 6 Connect with RS485............................................................................................................... 7 Mount a CCB22-100BT-03N Charge Base ......................................................................... 7 Reading Techniques...................................................................................................................... 8 Granit XP SR............................................................................................................................... 9 Granit XP XR ........................................................................................................................... 10 Granit XP XLR......................................................................................................................... 10 Menu Barcode Security Settings .......................................................................................... 10 Set Custom Defaults .................................................................................................................. 11 Reset the Custom Defaults...................................................................................................... 12
Granit XP User Guide
i
Chapter 2 - Program the Interface.............................................................. 13
Introduction ...................................................................................................................................13 Program the Interface - Plug and Play ...............................................................................13 Keyboard Wedge ..........................................................................................................................13 Laptop Direct Connect ..............................................................................................................14 RS232 Serial Port.........................................................................................................................14 RS485 ...............................................................................................................................................14 USB IBM SurePos ........................................................................................................................15 USB PC or Macintosh Keyboard ............................................................................................16 USB HID...........................................................................................................................................16 USB Serial .......................................................................................................................................16
CTS/RTS Emulation .............................................................................................................17 ACK/NAK Mode......................................................................................................................17 USBXNN .................................................................................................................................... 17 Verifone® Ruby Terminal............................................................................................................18 Gilbarco® Terminal.......................................................................................................................18 Honeywell Bioptic Aux Port .....................................................................................................18 DatalogicTM Magellan® Aux Port..............................................................................................19 Wincor Nixdorf Terminal ...........................................................................................................19 Wincor Nixdorf BeetleTM Terminal ..........................................................................................19 Wincor Nixdorf RS232 Mode A...............................................................................................20 Keyboard Country Layout.........................................................................................................20 Keyboard Wedge Modifiers......................................................................................................27 ALT Mode ..................................................................................................................................27 Keyboard Style ..............................................................................................................................28 Keyboard Conversion .................................................................................................................29 Control Character Output.........................................................................................................30 Keyboard Modifiers.....................................................................................................................30 RS232 Modifiers ..........................................................................................................................32 RS232 Baud Rate ..................................................................................................................32 RS232 Word Length: Data Bits, Stop Bits, and Parity ............................................33
ii
Granit XP User Guide
RS232 Receiver Time-Out..................................................................................................34 RS232 Handshake ................................................................................................................35 RS232 Timeout.......................................................................................................................35 XON/XOFF ...............................................................................................................................36 ACK/NAK...................................................................................................................................36 Scanner to Bioptic Communication .....................................................................................36 Scanner-Bioptic Packet Mode..........................................................................................37 Scanner-Bioptic ACK/NAK Mode....................................................................................37 Scanner-Bioptic ACK/NAK Timeout ..............................................................................37
Chapter 3 - Cordless System Operation .....................................................39
How the Cordless Charge Base Works.................................................................................39 Pair with a Honeywell Vehicle Mount Computer.......................................................39 Legacy Mode ...........................................................................................................................39 Compatibility Mode ..............................................................................................................40
Replace a Linked Scanner ........................................................................................................40 Communication Between the Cordless System and the Host ...................................40 Program the Scanner and Base or Access Point .............................................................41 RF (Radio Frequency) Module Operation...........................................................................41 System Conditions.......................................................................................................................42 Page Button....................................................................................................................................43
Temporary Streaming Presentation Timeout.............................................................43 Charge Information.....................................................................................................................44 Battery Information for the Granit XP 1991iSR, 1991iXR, and 1991iXLR............44
Battery Recommendations................................................................................................44 Safety Precautions for Lithium Batteries.....................................................................45 Beeper and LED Sequences and Meaning ........................................................................45 Scanner Communication and Scanning......................................................................45 Base/Access Point Communication and Scanning .................................................47 Base Power Communication Indicator .........................................................................47 Base Charge Status ..............................................................................................................47 About the Bluetooth Status and Battery Icons.................................................................48 About the Bluetooth Status Icon .....................................................................................48
Granit XP User Guide
iii
About the Battery Status Icon ..........................................................................................48 Reset Scanner ...............................................................................................................................49 Base Charge Modes....................................................................................................................49 Page ..................................................................................................................................................50
Page Mode ...............................................................................................................................50 Page Pitch ................................................................................................................................50 Error Indicators.............................................................................................................................51 Beeper Pitch - Base Error...................................................................................................51 Number of Beeps - Base Error .........................................................................................51 Scanner Report.............................................................................................................................51 Scanner Address ..........................................................................................................................52 Base or Access Point Address .................................................................................................52 Scanner Modes.............................................................................................................................52 Charge Only Mode ................................................................................................................52 Charge and Link Mode........................................................................................................53 Linked Modes .........................................................................................................................53 Unlink the Scanner......................................................................................................................54 Override Locked Scanner...................................................................................................54 Out-of-Range Alarm...................................................................................................................54 Alarm Sound Type .................................................................................................................55 Scanner Power Time-Out Timer.............................................................................................56 Flexible Power Management...................................................................................................57 Granit XP 1990i and 1991i................................................................................................57 Batch Mode ....................................................................................................................................58 Batch Mode Beep ..................................................................................................................59 Batch Mode Storage ............................................................................................................59 Batch Mode Quantity...........................................................................................................60 Enter Quantities.....................................................................................................................60 Batch Mode Output Order .................................................................................................62 Total Records...........................................................................................................................62 Delete Last Code ...................................................................................................................62 Clear All Codes .......................................................................................................................62 Transmit Records to Host ..................................................................................................63
iv
Granit XP User Guide
Batch Mode Transmit Delay ..............................................................................................63 Multiple Scanner Operation ....................................................................................................63 Scanner Name...............................................................................................................................64 Application Work Groups ..........................................................................................................65
Application Work Group Selection..................................................................................65 Reset the Factory Defaults: All Application Work Groups ............................................66 Reset the Custom Defaults: All Application Work Groups ...........................................67 Use the Scanner with Bluetooth Devices............................................................................67
Bluetooth Secure Simple Pairing (SSP)........................................................................67 Connect with Bluetooth Device Directly.......................................................................68 Virtual Keyboard.....................................................................................................................69 Bluetooth HID Keyboard Disconnect.............................................................................70 Bluetooth Serial Port - PCs/Laptops.............................................................................70 PDAs/Mobility Systems Devices .....................................................................................70 Change the Scanner's Bluetooth PIN Code ................................................................70 Minimize Bluetooth/ISM Band Network Activity ............................................................71 Auto Reconnect Mode .........................................................................................................71 Maximum Link Attempts ....................................................................................................72 Relink Time-Out .....................................................................................................................72 Bluetooth/ISM Network Activity Examples.................................................................73 Host Acknowledgment ...............................................................................................................73 Host ACK On/Off ...................................................................................................................75 Host ACK Timeout .................................................................................................................75 Host ACK Responses ............................................................................................................75
Chapter 4 - Input/Output Settings .............................................................77
Power Up Beeper ..........................................................................................................................77 Beep on BEL Character .............................................................................................................78 Trigger Click....................................................................................................................................78 Good Read and Error Indicators.............................................................................................78
Beeper Good Read .............................................................................................................78 Beeper Volume Good Read ............................................................................................79 Beeper Pitch Good Read .................................................................................................79
Granit XP User Guide
v
Vibrate Good Read.............................................................................................................80 Beeper Pitch Error .............................................................................................................80 Beeper Duration Good Read..........................................................................................81 LED Good Read ..................................................................................................................81 Number of Beeps Good Read........................................................................................81 Number of Beeps Error....................................................................................................81 Good Read Delay ...................................................................................................................82 User-Specified Good Read Delay....................................................................................82 Trigger Modes ...............................................................................................................................83 Manual Trigger .......................................................................................................................83 Trigger Toggle .........................................................................................................................83 Serial Trigger ...........................................................................................................................85 Trigger Mode 11.....................................................................................................................85 Presentation Mode......................................................................................................................86 Triggered Presentation Mode...........................................................................................86 Presentation LED Behavior after Decode....................................................................86 Presentation Centering.......................................................................................................87 Near-Far Camera Modes (XR & XLR Models only) .........................................................88 Camera Selection ..................................................................................................................88 Camera Sensors.....................................................................................................................89 Camera Illumination ............................................................................................................89 Poor Quality Codes......................................................................................................................90 Poor Quality 1D Codes ........................................................................................................90 Poor Quality PDF Codes .....................................................................................................91 Low Resolution PDF Codes ...............................................................................................91 CodeGateTM...................................................................................................................................... 91 Streaming PresentationTM Mode ............................................................................................92 Hands Free Time-Out.................................................................................................................92 Reread Delay..................................................................................................................................93 User-Specified Reread Delay............................................................................................93 2D Reread Delay ....................................................................................................................93 Character Activation ...................................................................................................................94 Activation Character ............................................................................................................94
vi
Granit XP User Guide
End Character Activation After Good Read .................................................................95 Character Activation Timeout...........................................................................................95 Character Deactivation..............................................................................................................95 Deactivation Character .......................................................................................................96 Illumination Lights ......................................................................................................................96 Aimer Delay.....................................................................................................................................96 User-Specified Aimer Delay...............................................................................................97 Aimer Mode ....................................................................................................................................97 Laser Aimer - Scan Duration ...................................................................................................97 Centering .........................................................................................................................................98 Single Code Centering.........................................................................................................98 Custom Centering .................................................................................................................98 Preferred Symbology ...............................................................................................................100 High Priority Symbology..................................................................................................101 Low Priority Symbology ...................................................................................................101 Preferred Symbology Time-out.....................................................................................101 Preferred Symbology Default ........................................................................................101 Output Sequence Overview...................................................................................................102 Output Sequence Editor ..................................................................................................102 To Add an Output Sequence...........................................................................................102 Output Sequence Editor Commands................................................................................103 Enter Output Sequence ..........................................................................................................105 Partial Sequence.................................................................................................................106 Good Read Tone - Output Sequences ........................................................................110 Multiple Symbols ......................................................................................................................110 No Read.........................................................................................................................................111 Video Reverse..............................................................................................................................111 Working Orientation.................................................................................................................112
Chapter 5 - Data Edit ...................................................................................113
Prefix/Suffix Overview ............................................................................................................113 Points to Keep In Mind .....................................................................................................113 Add a Prefix or Suffix: ........................................................................................................114
Granit XP User Guide
vii
Example: Add a Tab Suffix to All Symbologies........................................................ 114 Clear One or All Prefixes or Suffixes ........................................................................... 114 Add a Carriage Return Suffix to All Symbologies .................................................. 115 Prefix Selections........................................................................................................................ 115 Suffix Selections........................................................................................................................ 115 Function Code Transmit......................................................................................................... 116 Intercharacter, Interfunction, and Intermessage Delays.......................................... 116 Intercharacter Delay ......................................................................................................... 116 User Specified Intercharacter Delay........................................................................... 117 Interfunction Delay ........................................................................................................... 117 Intermessage Delay........................................................................................................... 118
Chapter 6 - Data Format .............................................................................119
Data Format Editor Introduction........................................................................................ 119 Show Data Format.................................................................................................................... 120 Add a Data Format.................................................................................................................... 120
Other Programming Selections.................................................................................... 121 Terminal ID Table................................................................................................................ 122 Data Format Editor Commands.......................................................................................... 122 Send Commands ................................................................................................................ 122 Move Commands ............................................................................................................... 128 Search Commands ............................................................................................................ 129 Miscellaneous Commands............................................................................................. 132 Data Formatter........................................................................................................................... 135 Data Format Non-Match Error Tone .......................................................................... 136 Primary/Alternate Data Formats ........................................................................................ 137 Single Scan Data Format Change ............................................................................... 137
Chapter 7 - Symbologies.............................................................................139
All Symbologies ......................................................................................................................... 140 Message Length Description............................................................................................... 140 Codabar ........................................................................................................................................ 140 Code 39......................................................................................................................................... 143
viii
Granit XP User Guide
Interleaved 2 of 5.......................................................................................................................146 NEC 2 of 5 ....................................................................................................................................148 Code 93 .........................................................................................................................................149 Straight 2 of 5 Industrial (three-bar start/stop) ...........................................................151 Straight 2 of 5 IATA (two-bar start/stop) .........................................................................152 Matrix 2 of 5 ................................................................................................................................153 Code 11 .........................................................................................................................................154 Code 128 ......................................................................................................................................155
ISBT 128 Concatenation..................................................................................................155 GS1-128 .......................................................................................................................................157 Telepen ..........................................................................................................................................158 UPC-A ............................................................................................................................................159 UPC-A/EAN-13 with Extended Coupon Code ..............................................................161 Coupon GS1 DataBar Output...............................................................................................162 UPC-E0 .........................................................................................................................................163 UPC-E1 .........................................................................................................................................165 E AN/JAN-13 ................................................................................................................................ 166
ISBN Translate .....................................................................................................................173 EAN/JAN-8 ..................................................................................................................................173 MSI ..................................................................................................................................................175 GS1 DataBar Omnidirectional .............................................................................................177 GS1 DataBar Limited...............................................................................................................178 GS1 DataBar Expanded..........................................................................................................178 Trioptic Code ...............................................................................................................................179 Codablock A.................................................................................................................................179 Codablock F.................................................................................................................................180 Label Code ...................................................................................................................................181 PDF417 .........................................................................................................................................181 MacroPDF417 ............................................................................................................................182 MicroPDF417 .............................................................................................................................182 GS1 Composite Codes ............................................................................................................183
Granit XP User Guide
ix
GS1 Emulation........................................................................................................................... 184 TCIF Linked Code 39 (TLC39) ............................................................................................. 185 QR Code........................................................................................................................................ 186
QR Code with Web Link.................................................................................................... 188 DotCode........................................................................................................................................ 188 Digimarc BarcodeTM .................................................................................................................. 189 Data Matrix.................................................................................................................................. 190 MaxiCode ..................................................................................................................................... 192 Aztec Code ................................................................................................................................... 193 Chinese Sensible (Han Xin) Code ...................................................................................... 194 Postal Codes - 2D ..................................................................................................................... 195
Planet Code Check Digit.................................................................................................. 198 Postnet Check Digit........................................................................................................... 199 Australian Post Interpretation....................................................................................... 199 Postal Codes - Linear.............................................................................................................. 200 China Post (Hong Kong 2 of 5) ..................................................................................... 200 Korea Post ............................................................................................................................. 201
Chapter 8 - Imaging Commands ...............................................................203
Single-Use Basis ....................................................................................................................... 203 Command Syntax ..................................................................................................................... 203 Image Snap - IMGSNP............................................................................................................ 204
IMGSNP Modifiers ............................................................................................................. 204 Image Ship - IMGSHP............................................................................................................. 207
IMGSHP Modifiers............................................................................................................. 208 Image Size Compatibility ................................................................................................ 215 Intelligent Signature Capture - IMGBOX ........................................................................ 216 Signature Capture Optimize .......................................................................................... 216 IMGBOX Modifiers............................................................................................................. 217 RF Default Imaging Device ................................................................................................... 221
Chapter 9 - Utilities......................................................................................223
To Add a Test Code I.D. Prefix to All Symbologies ........................................................ 223
x
Granit XP User Guide
Show Software Revision .........................................................................................................223 Test Menu.....................................................................................................................................223 TotalFreedom .............................................................................................................................. 224 Application Plug-Ins (Apps)..................................................................................................224 EZConfig for Scanning Introduction .................................................................................225
Configure with EZConfig for Scanning......................................................................225 Reset the Factory Defaults ....................................................................................................226
Chapter 10 - Serial Programming Commands....................................... 227
Conventions ................................................................................................................................227 Menu Command Syntax.........................................................................................................227 Query Commands .....................................................................................................................228 Trigger Commands...................................................................................................................230 Reset the Custom Defaults ...................................................................................................231 Menu Commands .....................................................................................................................232
Chapter 11 - Product Specifications........................................................ 261
Granit XP 1990i SR, XR, XLR Corded Scanner Product Specifications ...............261 Granit XP 1991i SR, XR, XLR Cordless Scanner Product Specifications ............262 CCB22-100BT-03N/COB22 Charge Base Product Specifications ......................264 Depth of Field Charts ..............................................................................................................265
Granit XP SR Performance..............................................................................................265 Granit XP XR Performance ....................................................................................................266
Granit XP XLR Performance...........................................................................................267 Standard Connector Pinouts................................................................................................268
Keyboard Wedge .................................................................................................................268 Serial Output ........................................................................................................................268 RS485 Output ......................................................................................................................269 USB........................................................................................................................................... 269 Required Safety Labels...........................................................................................................270 Scanner................................................................................................................................... 270 CCB22-100BT-03N-BF Base ........................................................................................271
Granit XP User Guide
xi
Chapter 12 - Maintenance and Troubleshooting ..................................273
Repairs .......................................................................................................................................... 273 Maintenance............................................................................................................................... 273
Clean the Scanner.............................................................................................................. 273 Inspect Cords and Connectors ..................................................................................... 274 Replace Cables in Corded Scanners........................................................................... 274 Replace an Interface Cable ............................................................................................ 274 Replace Cables and Batteries in Cordless Systems.................................................... 274 Replace an Interface Cable in a Base......................................................................... 274 Change a Scanner Battery.............................................................................................. 275 Troubleshoot a Corded Scanner ......................................................................................... 275 Troubleshoot a Cordless System ........................................................................................ 276 Troubleshoot a Base.......................................................................................................... 276 Troubleshoot a Cordless Scanner................................................................................ 276
Chapter A - Reference Charts ....................................................................279
Symbology Charts .................................................................................................................... 279 Linear Symbologies........................................................................................................... 279 2D Symbologies.................................................................................................................. 281 Postal Symbologies ........................................................................................................... 281
ASCII Conversion Chart (Code Page 1252).................................................................... 282 Lower ASCII Reference Table ............................................................................................... 283 ISO 2022/ISO 646 Character Replacements................................................................ 286 Keyboard Key References ...................................................................................................... 288
Sample Symbols ............................................................................................289
Programming Chart......................................................................................291
xii
Granit XP User Guide
Customer Support
Technical Assistance
Go to honeywell.com/PSStechnicalsupport to search our knowledge base for a solution or to log into the Technical Support portal. For our latest contact information, see sps.honeywell.com.
Product Service and Repair
Honeywell International Inc. provides service for all of its products through service centers throughout the world. Go to sps.honeywell.com and select Support to find a service center near you or to get a Return Material Authorization number (RMA #) before returning a product.
Limited Warranty
For warranty information, go to www.sps.honeywell.com and click Support > Warranties.
Granit XP User Guide
xiii
xiv
Granit XP User Guide
CHAPTER
1 GET STARTED
About This Manual
This User Guide provides installation and programming instructions for the GranitTM XP 1990iSR, 1990iXR, and 1990iXLR corded industrial area-imaging scanners and the Granit XP 1991iSR, 1991iXR, and 1991iXLR cordless industrial area-imaging scanners. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the barcodes in this guide. An asterisk (*) next to an option indicates the default setting.
Unpack Your Device
After you open the shipping carton containing the product, take the following steps: · Check for damage during shipment. Report damage immediately to the carrier
who delivered the carton. · Make sure the items in the carton match your order. · Save the shipping container for later storage or shipping.
Granit XP User Guide
1
Features of the Device
1990i/1991i SR Features
Provides extreme performance scanning even on damaged and low-quality barcodes. The SR is built to survive harsh treatment, including drops and extreme temperatures. Ideally suited to normal near-field scanning operations on 1D and 2D barcodes. For more information and specifications, see Depth of Field Charts on page 265.
1990i/1991i XR Features
Like the SR, XR provides extreme performance scanning even on damaged and low-quality barcodes. The XR is built to survive harsh treatment, including drops and extreme temperatures. Ideally suited to normal near-field scanning operations on 1D and 2D barcodes, with an expanded range scanning 100% UPC to 1.5m (5 ft) and 100 mil Code 39 barcodes to 10m (33 ft). For more information and specifications, see Depth of Field Charts on page 265.
For information about Bluetooth connection, see Connect with Bluetooth Device Directly on page 68.
1990i/1991i XLR Features
Like the SR and XR, XLR provides extreme performance scanning even on damaged and low quality barcodes. The XLR is built to survive harsh treatment, including drops and extreme temperatures. Ideally suited to normal near-field scanning operations on 1D and 2D barcodes, with an expanded range scanning 100% UPC to 2m (6.6 ft) and 100 mil Code 39 barcodes to 24m (79 ft). For more information and specifications, see Depth of Field Charts on page 265.
For information about Bluetooth connection, see Connect with Bluetooth Device Directly on page 68.
Connect a Corded Device
When connecting the corded scanner, make sure the cable is pushed tightly into the scanner. Loosen the locking plate and slide it over the base of the cable connector to lock the cable in place. Tighten the screw.
2
Granit XP User Guide
Note: It is important to insert the red O-ring onto the end of the communication cable as shown, and make sure that the O-ring cannot be seen after the cable is inserted into the scanner. This ensures proper assembly and IP65/67 compliance function.
Connect with USB
A scanner or a cordless base can be connected to the USB port of a computer.
1. Connect the appropriate interface cable to the device first, then to the computer.
Corded Granit XP Scanner USB Connection:
2. If you are connecting a CCB22-100BT-03N or a COB22-100BT-03N base horizontally, make sure the cables are secured in the wireways in the bottom of the cordless base and the base sits flat on a horizontal surface.
Granit XP User Guide
3
CCB22-100BT-03N Base USB Connection:
Note: The power supply must be ordered separately, if needed. 3. The scanner beeps. 4. Verify the scanner or cordless base operation by scanning a barcode from the Sample Symbols, beginning on page 289. The unit defaults to a USB PC Keyboard. Refer to page 16 for other USB terminal settings.
Connect with Keyboard Wedge
A scanner or cordless base can be connected between the keyboard and PC as a "keyboard wedge," where the scanner provides data output that is similar to keyboard entries. The following is an example of a keyboard wedge connection:
4
Granit XP User Guide
1. Turn off power and disconnect the keyboard cable from the back of the terminal/computer.
2. Connect the appropriate interface cable to the device and to the terminal/ computer.
Corded Granit XP Scanner Keyboard Wedge Connection:
Note: The power supply must be ordered separately, if needed.
CCB22-100BT-03N Base Keyboard Wedge Connection:
3. Turn the terminal/computer power back on. The scanner beeps.
4. Verify the scanner or cordless base operation by scanning a barcode from the Sample Symbols, beginning on page 289.
The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard. A carriage return (CR) suffix is added to barcode data.
Granit XP User Guide
5
Connect with RS232 Serial Port
1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner or cordless base to work properly, you must have the correct cable for your type of terminal/computer.
Corded Granit XP Scanner RS232 Serial Port Connection:
3. If you are connecting a the base horizontally, make sure the cables are secured in the wireways in the bottom of the cordless base and the base sits flat on a horizontal surface.
CCB22-100BT-03N Base RS232 Serial Port Connection:
Note: The power supply must be ordered separately, if needed.
6
Granit XP User Guide
4. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port.
5. Once the scanner or cordless base has been fully connected, power up the computer.
This interface programs 115,200 baud, 8 data bits, no parity, and 1 stop bit.
Connect with RS485
A Granit XP scanner can be connected for an IBM POS terminal interface.
1. Connect the appropriate interface cable to the device, then to the computer.
Corded Granit XP Scanner RS485 Connection:
2. Turn the terminal/computer power back on. The scanner beeps. 3. Verify the scanner operation by scanning a barcode from the Sample Symbols,
beginning on page 289. The scanner beeps once.
For further RS485 settings, refer to RS485, page 14.
Mount a CCB22-100BT-03N Charge Base
2.51 in. 63.7mm
5.31 in. 134.92mm
2 in. 51.17mm
Granit XP User Guide
2.36 in. 60mm
.84 in. 21.42mm
7
Reading Techniques
The Granit XP SR scanners have an aimer that projects a bright red spot/cross and corner indicators that correspond to the scanner's field of view. The aiming spot/ cross should be centered over the barcode, with the entire barcode falling within the corner indicators. The scanner can be positioned/rotated in any direction for a good read.
Granit XP XR scanners have an aimer that projects a bright red spot that corresponds to the scanner's center of field of view. The aiming dot should be centered over the barcode. The scanner can be positioned/rotated in any direction for a good read.
Granit XP XLR scanners have an aimer that projects a bright green spot that corresponds to the scanner's center of field of view. The aiming dot should be centered over the barcode. The scanner can be positioned/rotated in any direction for a good read.
8
Granit XP User Guide
Granit XP SR
Linear Barcodes and 2D matrix symbol with aiming dot.
Granit XP User Guide
9
Granit XP XR Granit XP XLR
Menu Barcode Security Settings
Honeywell scanners are programmed by scanning menu barcodes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Barcode Security settings. Contact the nearest technical support office (see Technical Assistance on page xiii) for further information.
10
Granit XP User Guide
Set Custom Defaults
You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults barcode below before scanning the menu commands for your custom defaults. If a menu command requires scanning numeric codes from the Programming Chart, beginning on page 291, then a Save code, that entire sequence will be saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults barcode.
Set Custom Defaults
Save Custom Defaults
Note: When using a cordless system, the Custom Defaults settings apply to all workgroups. Scanning the Save Defaults barcode also causes both the scanner and the base or Access Point to perform a reset and become unlinked. The scanner must be placed in its base to re-establish the link before any setup codes are entered. If using an Access Point, the linking barcode must be scanned. See Cordless System Operation beginning on page 39 for additional information.
You may have a series of custom settings and want to correct a single setting. To do so, just scan the new setting to overwrite the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and decide you want the beeper volume set to High, just scan the Set Custom Defaults barcode, then scan the Beeper Volume High menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be updated.
Granit XP User Guide
11
Reset the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults barcode below. This is the recommended default barcode for most users. It resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings.
Activate Custom Defaults
Note: If using a cordless system, scanning this barcode also causes both the scanner and the base or Access Point to perform a reset and become unlinked. The scanner must be placed in its base to re-establish the link. If using an Access Point, the linking barcode must be scanned. See Cordless System Operation beginning on page 39 for additional information.
12
Granit XP User Guide
CHAPTER
2 PROGRAM THE INTERFACE
Introduction
This chapter describes how to program your system for the desired interface.
Program the Interface - Plug and Play
Plug and Play barcodes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.
Keyboard Wedge
If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard, scan the barcode below. Keyboard wedge is the default interface. Note: The following barcode also programs a carriage return (CR) suffix.
IBM PC AT and Compatibles with CR suffix
Granit XP User Guide
13
Laptop Direct Connect
For most laptops, scanning the Laptop Direct Connect barcode allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect barcode also programs a carriage return (CR) suffix and turns on Emulate External Keyboard (page 29).
Laptop Direct Connect with CR suffix
RS232 Serial Port
The RS232 Interface barcode is used when connecting to the serial port of a PC or terminal. The following RS232 Interface barcode also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below. It also changes the trigger mode to manual.
Option Baud Rate Data Format
Setting 115,200 bps 8 data bits, no parity bit, 1 stop bit
RS232 Interface
RS485
Scan one of the following "Plug and Play" codes to program the scanner for an IBM POS terminal interface. Note: After scanning one of these codes, you must power cycle the cash register.
IBM Port 5B Interface
IBM Port 9B HHBCR-1 Interface
14
Granit XP User Guide
IBM Port 17 Interface
IBM Port 9B HHBCR-2 Interface
Each barcode above also programs the following suffixes for each symbology:
Symbology EAN 8 EAN 13 UPC A UPC E
Suffix 0C 16 0D 0A
Symbology Code 39 Interleaved 2 of 5 Code 128 * Code 128 ** MaxiCode
Suffix 00 0A 0B 00 0D 0B 00 0A 0B 00 18 0B 00 2F 0B
* Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces
**Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface
USB IBM SurePos
Scan one of the following "Plug and Play" codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface.
Note: After scanning one of these codes, you must power cycle the cash register.
USB IBM SurePos (USB Handheld Scanner)
Interface
USB IBM SurePos (USB Tabletop Scanner)
Interface
Each barcode above also programs the following suffixes for each symbology:
Symbology EAN 8 EAN 13 UPC A UPC E
Suffix 0C 16 0D 0A
Symbology Code 39 Interleaved 2 of 5 Code 128 Code 39
Suffix 00 0A 0B 00 0D 0B 00 18 0B 00 0A 0B
Granit XP User Guide
15
USB PC or Macintosh Keyboard
Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard. Scanning these codes also adds a CR suffix.
USB Keyboard (PC)
USB Keyboard (Mac)
USB Japanese Keyboard (PC)
USB HID
Scan the following code to program the scanner for USB HID Barcode scanners.
USB HID Barcode Scanner
USB Serial
If you are using a Microsoft® Windows® PC, you will need to download the latest driver from the Honeywell website (sps.honeywell.com) and go to Get Resources Downloads - Software. The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically use a class driver.
After the driver is downloaded, scan the following code to program the scanner to emulate a regular RS232-based COM Port.
USB Serial
No extra configuration (e.g., baud rate) is necessary.
Note: If you scan the USB Serial barcode either with an older Honeywell serial driver, or no driver installed, you may no longer be able to scan barcodes. If this happens, either uninstall the older driver versions and install the latest driver, or delete the specific device entry in Device Manager.
16
Granit XP User Guide
CTS/RTS Emulation
CTS/RTS Emulation On
ACK/NAK Mode
ACK/NAK Mode On
USBXNN
*Report PID as built Report PID as Granit 1980i
Granit XP User Guide
* CTS/RTS Emulation Off * ACK/NAK Mode Off
Report PID as Granit 1910i
17
Verifone® Ruby Terminal
Scan the following Plug and Play code to program the scanner for a Verifone Ruby terminal. This barcode sets the baud rate to 1200 bps and the data format to 8 data bits, mark parity bit, 1 stop bit. It also adds a line feed (LF) suffix and programs the following prefixes for each symbology:
Symbology UPC-A UPC-E EAN-8 EAN-13
Prefix A A FF F
Verifone Ruby Settings
Gilbarco® Terminal
Scan the following Plug and Play code to program the scanner for a Gilbarco terminal. This barcode sets the baud rate to 2400 bps and the data format to 7 data bits, even parity, 2 stop bits. It also adds a carriage return (CR) suffix and programs the following prefixes for each symbology:
Symbology UPC-A UPC-E EAN-8 EAN-13
Prefix A E0 FF F
Gilbarco Settings
Honeywell Bioptic Aux Port
Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This barcode sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Honeywell Bioptic Settings
18
Granit XP User Guide
DatalogicTM Magellan® Aux Port
Scan the following Plug and Play code to program the scanner for a Datalogic Magellan auxiliary port configuration. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.
Datalogic Magellan Settings
Wincor Nixdorf Terminal
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.
Wincor Nixdorf Terminal Settings
Wincor Nixdorf BeetleTM Terminal
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal. The following prefixes are programmed for each symbology:
Symbology Aztec Code Codabar Code 93 Code 128 Data Matrix EAN-8 EAN-13 GS1 DataBar GS1-128
Prefix V N L K R B A E P
Symbology
Prefix
Interleaved 2 of 5 I
MaxiCode
T
MicroPDF417
S
PDF417
Q
QR Code
U
Straight 2 of 5 IATA H
UPC-A
A0
UPC-E
C
All other barcodes M
Wincor Nixdorf Beetle Settings
Granit XP User Guide
19
Wincor Nixdorf RS232 Mode A
Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf RS232 Mode A terminal. This barcode sets the baud rate to 9600 bps and the data format to 8 data bits, odd parity, 1 stop bit. The following prefixes are programmed for each symbology:
Symbology Code 128 Code 93 Codabar UPC-A UPC-E EAN-8 All other barcodes
Prefix K L N A0 C B M
Symbology
Prefix
EAN-13
A
GS1-128
K
Interleaved 2 of 5 I
Straight 2 of 5 IATA H
GS1 DataBar
E
Wincor Nixdorf RS232 Mode A Settings
Keyboard Country Layout
If your interface is USB Keyboard or Keyboard Wedge, your keyboard layout default is a US keyboard. To change this layout, scan the appropriate Keyboard Country barcode below. By default, national character replacements are used for the following characters: # $ @ [ \ ] ^ ` { | } ~. Refer to the ISO 2022/ISO 646 Character Replacements on page 286 to view the character replacements for each country.
Keyboard Countries
* United States
Albania
Azeri (Cyrillic)
Azeri (Latin)
20
Granit XP User Guide
Keyboard Countries (Continued)
Belarus Bosnia Brazil (MS) Bulgaria (Latin) Canada (French) Croatia
Granit XP User Guide
Belgium Brazil Bulgaria (Cyrillic) Canada (French legacy) Canada (Multilingual) Czech
21
Keyboard Countries (Continued)
Czech (Programmers) Czech (QWERTZ)
Dutch (Netherlands) Faroese France
Germany
22
Czech (QWERTY) Denmark Estonia Finland Gaelic Greek
Granit XP User Guide
Keyboard Countries (Continued)
Greek (220 Latin) Greek (319 Latin)
Greek (Latin) Greek (Polytonic) Hungarian (101 key)
Iceland
Granit XP User Guide
Greek (220) Greek (319) Greek (MS)
Hebrew Hungary
Irish
23
Keyboard Countries (Continued)
Italian (142) Japan ASCII Kyrgyz (Cyrillic)
Latvia Lithuania Macedonia
24
Italy Kazakh Latin America Latvia (QWERTY) Lithuania (IBM) Malta
Granit XP User Guide
Keyboard Countries (Continued)
Mongolian (Cyrillic) Poland
Polish (Programmers) Romania
Russian (MS) SCS
Granit XP User Guide
Norway Polish (214)
Portugal Russia
Russian (Typewriter) Serbia (Cyrillic)
25
Keyboard Countries (Continued)
Serbia (Latin) Slovakia (QWERTY)
Slovenia Spanish variation Switzerland (French)
Tatar
26
Slovakia Slovakia (QWERTZ)
Spain Sweden Switzerland (German) Turkey F
Granit XP User Guide
Keyboard Countries (Continued)
Turkey Q
Ukrainian
United Kingdom
United States (Dvorak)
United States (Dvorak left)
United States (Dvorak right)
United States (International)
Uzbek (Cyrillic)
Keyboard Wedge Modifiers
ALT Mode
If your barcode contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode. (See Extended ASCII Characters on page 283.) Note: Scan the ALT mode barcode after scanning the appropriate Keyboard Country code.
Granit XP User Guide
27
If your keystrokes require the ALT key and 3 or 4 characters, scan the 3 Characters or 4 Characters barcode. The data is then output with the special character(s) for values 00-255. Default = Off.
* Off
3 Characters
4 Characters
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Keyboard Style settings. Default = Regular. Regular is used when you normally have the Caps Lock key off.
* Regular
Caps Lock is used when you normally have the Caps Lock key on.
Caps Lock
Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards).
Shift Lock
Caps Lock Shift Enable is used two different ways. In Europe, Shift is used to close caps. In China, Shift is used to switch from Chinese to English. Default = Europe.
28
Granit XP User Guide
* Europe
China
Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off. This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).
Automatic Caps Lock
Autocaps via NumLock barcode should be scanned in countries (e.g., Germany, France) where the Caps Lock key cannot be used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve the current state of the Caps Lock.
Autocaps via NumLock
Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent).
Emulate External Keyboard
Note: After scanning the Emulate External Keyboard barcode, you must power cycle your computer.
Keyboard Conversion
Alphabetic keyboard characters can be forced to be all upper case or all lowercase. So if you have the following barcode: "abc569GK," you can make the output "ABC569GK" by scanning Convert All Characters to Upper Case, or to "abc569gk" by scanning Convert All Characters to Lower Case. These settings override Keyboard Style selections.
Note: If your interface is a keyboard wedge, first scan the menu code for Automatic Caps Lock (page 29). Otherwise, your output may not be as expected.
Granit XP User Guide
29
Default = Keyboard Conversion Off.
* Keyboard Conversion Off
Convert All Characters to Upper Case
Convert All Characters to Lower Case
Control Character Output
This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page 1252) on page 282. Only codes 00 through 1F are converted (the first column of the chart). Default = Off.
Note: Control + X (Control + ASCII) Mode overrides this mode.
Control Character Output On
* Control Character Output Off
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode. Control + X (Control + ASCII) Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F. Windows is the preferred mode. All keyboard country codes are supported. DOS mode is a legacy mode, and it does not support all keyboard country codes. New users should use the Windows mode. Refer to ASCII Conversion Chart (Code Page 1252), page 282 for CTRL+ X Values.
30
Granit XP User Guide
Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII control characters for values 00-1F, but it does not translate prefix or suffix information.
Support ALT 3 Digit HEX Mode: The scanner sends key combinations for ASCII control characters for values 00-1F transmitted as the ALT key and 3 digits.
Default = Control + X Mode Off.
Windows Mode Control + X Mode On
* Control + X Mode Off
DOS Mode Control + X Mode On
Windows Mode Prefix/Suffix
DOS Mode Control + X Mode On with Windows Mode Prefix/Suffix
Supports ALT 3 Digit HEX Mode
Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode. Default = Off.
Turbo Mode On
* Turbo Mode Off
Granit XP User Guide
31
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off.
Numeric Keypad Mode On
* Numeric Keypad Mode Off
Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping characters. Default = Off.
Automatic Direct Connect Mode On
* Automatic Direct Connect Mode Off
RS232 Modifiers
RS232 Baud Rate
Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 115,200.
300
600
1,200
32
Granit XP User Guide
2,400
4,800
9,600
19,200
38,400
57,600
* 115,200
RS232 Word Length: Data Bits, Stop Bits, and Parity
Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select 8 data bits per character. Default = 8. Stop Bits sets the stop bits at 1 or 2. Default = 1. Parity provides a means of checking character bit patterns for validity. Default = None.
7 Data, 1 Stop, Parity Even
Granit XP User Guide
7 Data, 1 Stop, Parity None
33
7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity None 8 Data, 1 Stop, Parity Even
7 Data, 2 Stop, Parity Even 7 Data, 2 Stop, Parity Odd
* 8 Data, 1 Stop, Parity None
8 Data, 1 Stop, Parity Odd
8 Data, 1 Stop, Parity Mark
RS232 Receiver Time-Out
The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual or serial trigger resets the time-out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time-out. A transaction on the CTS line will also wake up the receiver. The receiver takes 300 milliseconds to completely come up. Change the RS232 receiver time-out by scanning the barcode below, then scanning digits from the Programming Chart, beginning on page 291, then scanning Save. The range is 0 to 300 seconds. Default = 0 seconds (no time-out - always on).
RS232 Receiver Time-Out
34
Granit XP User Guide
RS232 Handshake
RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. When RTS/CTS is turned Off, no data flow control is used. Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be asserted by the host. Two-Direction Flow Control: The scanner asserts RTS when it is OK for the host to transmit. The host asserts CTS when it is OK for the device to transmit. Flow Control with Timeout: The scanner asserts RTS when it has data to send and waits for a delay (see RS232 Timeout on page 35) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the device transmit buffer is cleared and scanning may resume. Default = RTS/CTS Off.
Flow Control, No Timeout
Two-Direction Flow Control
Flow Control with Timeout
* RTS/CTS Off
RS232 Timeout
When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the barcode below, then setting the timeout (from 1-5100 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then scanning Save.
RS232 Timeout
Granit XP User Guide
35
XON/XOFF
Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop sending data (XON/XOFF Off). When the host sends the XOFF character (DC3, hex 13) to the scanner, data transmission stops. To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off when XOFF was sent. Default = XON/XOFF Off.
XON/XOFF On
* XON/XOFF Off
ACK/NAK
After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the host. If ACK is received, the communications cycle is completed and the scanner looks for more barcodes. If NAK is received, the last set of barcode data is retransmitted and the scanner waits for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK On barcode below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK Off.
ACK/NAK On
* ACK/NAK Off
Scanner to Bioptic Communication
The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner's baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner. See "RS232 Modifiers" on page 32, and RS232 Timeout on page 35 for further information.
36
Granit XP User Guide
Scanner-Bioptic Packet Mode
Packet Mode On must be scanned to set the scanner's format so it is compatible with a bioptic scanner. Default = Packet Mode Off.
* Packet Mode Off
Packet Mode On
Scanner-Bioptic ACK/NAK Mode
Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each packet is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response. Default = Bioptic ACK/NAK Off.
* Bioptic ACK/NAK Off
Bioptic ACK/NAK On
Scanner-Bioptic ACK/NAK Timeout
This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner's ACK/NAK response. Scan the barcode below, then set the timeout (from 130,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then scanning Save. Default = 5100.
ACK/NAK Timeout
Granit XP User Guide
37
38
Granit XP User Guide
CHAPTER
3 CORDLESS SYSTEM OPERATION
How the Cordless Charge Base Works
A CCB22-100BT-03N cordless charge base provides the link between the cordless scanner and the host system. The base contains an interface assembly and an RF communication module. The RF communication module performs the data exchange between the cordless scanner and the interface assembly. The control assembly coordinates the central interface activities including: transmitting/ receiving commands and data to/from the host system, performing software activities (parameter menuing, visual indicator support, power-on diagnostics), and data translation required for the host system.
Pair with a Honeywell Vehicle Mount Computer
A Granit XP SR, Granit XP XR, or Granit XP XLR can pair with Honeywell vehicle mounted computers. Scan the EZPairing barcode that is either supplied with the vehicle mount computer, attached to the vehicle mount computer, or displayed on the screen. The EZPairing barcode begins with {FNC3} LnkB, followed by 12 digits, like the sample below.
Legacy Mode
In Legacy Mode, the scanner works in SPP.
*Legacy Mode
Granit XP User Guide
39
Compatibility Mode
In Compatibility Mode, the scanner can work with HID, SPP, or other Bluetooth profiles. Bluetooth needs to be set manually before scanning this barcode.
Compatibility Mode (optional)
Replace a Linked Scanner
If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner barcode below with a new scanner and place that scanner in the base, or scan the Access Point linking barcode. The locked link will be overridden, the broken or lost scanner's link with the base or Access Point will be removed, and the new scanner will be linked.
Override Locked Scanner (Single Scanner)
Communication Between the Cordless System and the Host
The cordless scanner provides immediate feedback in the form of a "good read" indication with a green LED on the scanner and an audible beep. The scanner also vibrates, if programmed to do so. This indicates that the barcode has been scanned correctly and the base or Access Point has acknowledged receiving the data. This is possible since the cordless system provides two-way communication between the scanner and the base or Access Point.
40
Granit XP User Guide
When data is scanned, the data is sent to the host system via the base or Access Point. The cordless scanner recognizes data acknowledgment (ACK) from the base or Access Point. If it cannot be determined that the data has been properly sent to the base or Access Point, the scanner issues an error indication. You must then check to see if the scanned data was received by the host system.
1. Scanner reads code and gets ACK from base or Access Point. 2. Base or Access Point sends data to host.
Program the Scanner and Base or Access Point
When using the scanner and charge base or Access Point together as a system, menu parameters and configuration settings are stored in the charge base or Access Point. Therefore, when programming any menu configuration settings, the scanner must be linked to the intended charge base or Access Point.
Note: This only applies when the scanner is linked to a charge base or Access Point. If the scanner is in a non-base mode, configuration settings are stored in the scanner.
RF (Radio Frequency) Module Operation
The cordless system uses a two-way BluetoothTM radio to transmit and receive data between the scanner and the base or Access Point. Designed for point-to-point and multi-point-to-single point applications, the radio operates using a license free ISM band, which sends relatively small data packets at a fast data rate over a radio signal with randomly changing frequencies, makes the cordless system highly responsive to a wide variety of data collection applications and resistant to
Granit XP User Guide
41
noisy RF environments. The bases (Bluetooth Class 1 or Class 2) provide a communication range of 328 feet (100m) or 33 feet (10m) between the scanner and base or Access Point, depending on the environment. See Flexible Power Management, page 57, for information about controlling this range.
System Conditions
The components of the cordless system interact in specific ways as you associate a scanner to a base or Access Point, as you move a scanner out of range, bring a scanner back in range, or swap scanners between two cordless systems. The following information explains the cordless system operating conditions.
Link Process
Once a scanner is placed into a cordless charge base, the scanner's charge status is checked, and software automatically detects the scanner and links it to the base depending on the selected link mode.
Scanner Is Out of Range
The cordless scanner is in communication with its base or Access Point, even when it is not transmitting barcode data. Whenever the scanner can't communicate with the base or Access Point for a few seconds, it is out of range. If the scanner is out of range and you scan a barcode, the scanner issues an error tone indicating no communication with the base or Access Point. A cordless charge base can also sound an alarm. Refer to Out-of-Range Alarm, page 54.
Scanner Is Moved Back Into Range
The scanner relinks if the scanner or the base or Access Point have been reset, or the scanner comes back into range. If the scanner relinks, you will hear a single chirp when the relinking process (uploading of the parameter table) is complete. Refer to Out-of-Range Alarm on page 54 for further information.
Out of Range and Back into Range with Batch Mode On
The scanner may store a number of symbols (approximately 500 U.P.C. symbols; others may vary) when it is out of range and then send them to the base or Access Point when back in range (see Batch Mode on page 58).
You will not hear a communication error tone in this mode, but you will hear a short buzz when you press the trigger if the radio communication is not working. Once the radio connection is made, the scanner produces a series of beeps while the data is being transferred to the base or Access Point.
42
Granit XP User Guide
Page Button
When you press the page button on the base or Access Point, the scanners associated with that base or Access Point will begin beeping (3 short and 1 long beep). If you press the trigger on a scanner that is beeping in response, or press the page button on the base or Access Point a second time, all associated scanners will stop beeping. See Page on page 50 for further information about page button settings.
PAGE BUTTON
Temporary Streaming Presentation Timeout
Set a timeout for the length of time the illumination remains on and searching for barcodes when using Temporary Streaming Presentation Mode. Set the length for the timeout by scanning one of the barcodes below. Default = 10,000 ms (10 seconds).
*10 Second Timeout
30 Second Timeout
Granit XP User Guide
43
Charge Information
The battery or charge pack is designed to charge while the scanner is positioned in the cordless base unit. Refer to Scanner Communication and Scanning, page 45, for an interpretation of the Charge Status indicators. Refer to Charge Only Mode (page 52) if you need to charge a scanner without linking it to the base.
Place the scanner in the base that is connected to an appropriate power supply. Use only a Listed Limited Power Source (LPS) or Class 2 type power supply with output rated 5 to 5.2Vdc, 1A.
Note: If you are powering the base through the interface cable (for example, a USB cable) and not using an external power supply plugged into the aux port, the current available for charging is reduced and charge times are increased.
Battery Information for the Granit XP 1991iSR, 1991iXR, and 1991iXLR
Power is supplied to the scanner by a rechargeable battery that is integrated in the scanner handle. Batteries are shipped only partially charged. The battery should be charged for a minimum of 4 hours before initial use to ensure optimal performance.
Battery Recommendations
· To learn more about Battery Maintenance for Portable Devices, go to honeywell.com/PSS-BatteryMaintenance.
· The battery is a lithium ion cell and can be used without a full charge, and can also be charged without fully discharging, without impacting the battery life. There is no need to perform any charge/discharge conditioning on this type of battery.
· Keep the base connected to power when the host is not in use.
· Replace a defective battery immediately since it could damage the scanner.
· Although your battery can be recharged many times, it will eventually be depleted. Replace it after the battery is unable to hold an adequate charge.
· If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized service center for inspection. Refer to Customer Support on page xiii for additional information.
Caution: Use only Honeywell Li-ion battery packs, model number BATSCN05 (or legacy Granit BAT-SCN01/BAT-SCN01A), rated 3.7 Vdc, 7.4Whr in this device. Use of any non-Honeywell battery may result in damage not covered by the warranty.
44
Granit XP User Guide
Safety Precautions for Lithium Batteries
· Do not place batteries in fire or heat the batteries.
· Do not store batteries near fire or other high temperature locations.
· Do not store or carry batteries together with metal objects.
· Do not expose batteries to water or allow the batteries to get wet.
· Do not connect (short) the positive and negative terminals, of the batteries, to each other with any metal object.
· Do not pierce, strike or step on batteries or subject batteries to strong impacts or shocks.
· Do not disassemble or modify batteries.
Caution: Danger of explosion if batteries are incorrectly replaced. Dispose of used batteries according to the recycle program for batteries as directed by the governing agency for the country where the batteries are to be discarded.
Beeper and LED Sequences and Meaning
The scanner contains LEDs on the rear of the unit that indicate linking status, decoding state, and battery condition or instant charge pack condition. The base has LEDs on the top of the unit that indicate its power up, communication, and battery charge condition or instant charge pack condition.
For more information see, About the Bluetooth Status and Battery Icons on page 48
Scanner Communication and Scanning
The following feedback is provided by the scanner and indicates communication and scanning status.
LED
Beeper
Normal Operation
Green Flash
1 Beep
Red, Blinking
Razz or Error Tone
Menu Operation
Green Flash
2 Beeps
Red, Blinking
Razz or Error Tone
Cause
Successful communication or linking Failed communication
Successful menu change Unsuccessful menu change
Granit XP User Guide
45
Querying battery volume by three times trigger in 2 seconds when the scanner is out of the base will activate the battery status icon.
Note: This functionality is only available with the smart battery pack.
Battery Icon LED
Querying battery volume by three times trigger in 2 seconds when the scanner is out of the base will activate the battery status icon
Red
3 sets of quick flashes in a row
Yellow
3 sets of quick flashes in a row
Green
3 sets of quick flashes in a row
Scanner Beep No beep
No beep
No beep
When the scanner is in the base
2 sets of flashes then off 10 seconds
When the scanner is out of the base and has been idle for 5 seconds
3 sets of flashes repeatedly every 3 seconds
2 sets of flashes then off 10 seconds
3 sets of flashes repeatedly every 3 seconds
No beep
No beep
2 sets of flashes then off 10 seconds
Steady on
No beep
No beep No beep
No beep
20 sets of rapid flashes
No beep
Charge Level <20% 20%-40% >40%
<20% 20%-40% >40% 100% <15%
<5%
<2%
46
Granit XP User Guide
Base/Access Point Communication and Scanning
The following feedback is provided by the base (red LED) or Access Point (blue LED) and indicates communication and scanning status.
LED
Off
On continuously
Short blinks in multiple pulses. Occurs while transferring data to/from the RF module or the Host port.
Communication Condition USB suspend Power on, system idle Receiving data
Base Power Communication Indicator
To display the power indicator on a base or an Access Point, scan the Base Power Communication Indicator On barcode. To turn off the power indicator, scan the Off barcode. Default = On.
* Base Power Communication Indicator On
Base Power Communication Indicator Off
Base Charge Status
When charging the base indicates the progress while the scanner resides in the base.
LED
Green On Green Slow Blink Green Fast Blink Yellow Fast Blink
Charge Level
100% 50-99% 30-50% 0-30%
Approximate Expected Scans (see note)
450 200 100 Charging, do not scan
Note: The number of scans was measured with a clearly printed UPC code in good light. The approximate number of scans varies with changes in label quality, Symbology, and environmental factors.
Granit XP User Guide
47
About the Bluetooth Status and Battery Icons
Bluetooth Status Icon
Battery Status Icon:
About the Bluetooth Status Icon
The blue Bluetooth Icon LED has two behaviors flash and on. The icon will flash when linking to a device then will remain on, indicating the base and scanner are linked and stays on when the scanner is in base.
Once the scanner is removed from base, the blue LED stays on for four seconds then turns off.
Note: Link status can be checked by holding the trigger for three seconds, the BT LED will stay on for four seconds when BT is linked.
About the Battery Status Icon
The Battery status icon displays the charged level of the battery. Low-power alerts are non-configurable. See the table below to learn more about low power indicators.
Scanner LED Yellow 3 sets of flashes
Scanner Beep No beep
Charge Level <15%
48
Granit XP User Guide
Scanner LED
Red 3 sets of flashes, repeatedly every 3 seconds Red 20 sets of rapid flashes
Scanner Beep No Beep
No Beep
Charge Level <5%
<2%
Reset Scanner
Scanning this barcode reboots the scanner and causes it to relink with the base or Access Point.
Reset Scanner
Base Charge Modes
When the base has both an external power supply (plugged into the auxiliary power port) and a host interface cable, it will draw its power from the external power supply. When the base does not have an external power supply, it draws its power from the interface cable. However, the scanner charges more slowly from a host interface cable than if auxiliary power were available. Using the following selections, you can specify whether the scanner is charged from power supplied via the host interface cable.
When Base Charge Off is selected, the scanner does not charge when the scanner is in the base cradle.
When External or Interface Cable Power is selected, the scanner charges from the base's external power supply, if there is one. If there is no external power supply to the base, the scanner charges from the interface cable.
When External Power Only is selected, the scanner only charges from the base's external power supply. If there is no external power supply, the scanner does not charge.
Default = External or Interface Cable Power.
Base Charge Off
* External or Interface Cable Power
Granit XP User Guide
49
External Power Only
Page
Page Mode
By default, the page button on the base or Access Point pages the scanners associated with that base or Access Point. If you want the page button on your base or Access Point to be disabled, scan the Page Mode Off barcode, below. When Page Mode is off, the base or Access Point will no longer page scanners when the button is pressed. The red LED on the base or blue LED on the Access Point will remain lit to indicate that page mode is off. (This light will go out when the button is pressed, then back on when it's released.) Default = Page Mode On.
* Page Mode On
Page Mode Off
Page Pitch
When you press the page button on the base or Access Point, the scanners associated with that base or Access Point will begin beeping (see Page Button on page 43). You can set the pitch of the paging beep for each scanner by scanning one of the following barcodes. Default = Low.
* Low (1000 Hz) High (4200 Hz)
Medium (3250 Hz)
50
Granit XP User Guide
Error Indicators
Beeper Pitch - Base Error
The base can be configured to beep at a particular pitch when an error occurs, such as transmission problems to a host system. The beeper pitch codes modify the pitch (frequency) of the error tone the base emits when there is an error. Default = Low.
* Low/Razz (250 Hz)
Medium (3250 Hz)
High (4200 Hz)
Number of Beeps - Base Error
The number of beeps and LED flashes emitted by the base for an error condition can be programmed from 1 - 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response to an error. To change the number of error beeps, scan the barcode below and then scan a digit (1-9) from the Programming Chart, beginning on page 291, then Save. Default = 1.
Number of Base Error Beeps/LED Flashes
Scanner Report
Scan the barcode below to generate a report for the connected scanners. The report indicates the port, work group, scanner name, and address. To assign a name to your scanner, refer to Menu Command Syntax, page 227.
Scanner Report
Granit XP User Guide
51
Scanner Address
Scan the barcode below to determine the address of the scanner you are using.
Scanner Address
Base or Access Point Address
Scan the barcode below to determine the address of the base or Access Point you are using.
Base Address
Scanner Modes
Your scanner is capable of working in single scanner mode, multiple scanner mode, or with Bluetooth devices other than a charge base or Access Point.
Charge Only Mode
There may be times when you want to charge your scanner, but not link to the base. For example, if a scanner is linked to an Access Point or other Bluetooth device and you need to charge the scanner, but want to retain your existing link. In order to program the base for Charge Only Mode, you must link a scanner to it. Once the scanner is linked to the base, scan the Charge Only Mode barcode. Any subsequent scanners placed in that base will charge without linking to it. The scanner used to program the base remains linked to the base. To unlink this scanner, scan Unlink Scanner on page 54.
Charge Only Mode
Note: When in Charge Only Mode, the scanner periodically wakes up and beeps. See Power Up Beeper on page 77 to change this setting.
52
Granit XP User Guide
Charge and Link Mode
If you want to charge a scanner and link to the base, use Charge and Link Mode. If the base is programmed for Charge Only Mode, you must link a scanner to it first in order to program it for Charge and Link Mode. Scan the linking barcode on the base to link the scanner, then scan Charge and Link Mode. Default = Charge and Link Mode.
* Charge and Link Mode
Linked Modes
Locked Link Mode and Open Link Mode are the link modes that accommodate different applications. Scan the appropriate barcodes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another. Default = Open Link Mode.
Locked Link Mode - Single Scanner
If you link a scanner to a base or an Access Point using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base, or if the Access Point linking barcode is scanned. If you do place a different scanner into a base, it will charge the scanner, but the scanner will not be linked.
Locked Link Mode (Single Scanner)
To use a different scanner, you need to unlink the original scanner by scanning the Unlink Scanner barcode. (See Unlink the Scanner, page 54.)
Open Link Mode - Single Scanner
When newly shipped or defaulted to factory settings, a scanner is not linked to a base or an Access Point. A link is established when the scanner is placed into a base, or an Access Point linking barcode is scanned. When in Open Link Mode, a new link is established when a new scanner is placed in the base, or you scan an Access Point linking barcode. Each time a scanner is placed into a base or scans an Access Point linking barcode, the scanner becomes linked to the base or Access point and the old scanner is unlinked.
* Open Link Mode (Single Scanner)
Granit XP User Guide
53
Unlink the Scanner
If a base or an Access Point has a scanner linked to it, that scanner must be unlinked before a new scanner can be linked. Once the previous scanner is unlinked, it will no longer communicate with the base or Access Point. To unlink the scanner from a base or an Access Point, scan the Unlink Scanner barcode below.
Unlink Scanner
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a base or an Access Point, scan the Override Locked Scanner barcode below with a new scanner and place that scanner in the base, or scan the Access Point linking barcode. The locked link will be overridden; the broken or lost scanner's link with the base or Access Point will be removed, and the new scanner will be linked.
Override Locked Scanner (Single Scanner)
Out-of-Range Alarm
If your scanner is out range of the base, an alarm sounds from both your base and scanner. If your scanner is out range of an Access Point, an alarm sounds from just the scanner. The alarm stops when the scanner is moved closer to the base or Access Point, when the base or Access Point connects to another scanner, or when the alarm duration expires. To activate the alarm options for the scanner or the
54
Granit XP User Guide
base and to set the alarm duration, scan the appropriate barcode below and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart, beginning on page 291, then Save. Default = 0 sec (no alarm).
Base Alarm Duration
Note: The Access Point does not have a base alarm.
Scanner Alarm Duration
Note: If you are out of range when you scan a barcode, you will receive an error tone even if you do not have the alarm set. You receive the error tone because the data could not be sent to the base or Access Point or the host.
Alarm Sound Type
You may change the alarm type for the scanner or base by scanning the appropriate barcode below and then scanning a digit (0-7) barcode from the Programming Chart, beginning on page 291, then Save. Default = 0.
The sounds are as follows:
Setting 0 1 2 3 4 5 6 7
Sound 3 long beeps, medium pitch 3 long beeps, high pitch 4 short beeps, medium pitch 4 short beeps, high pitch single chirps, medium pitch 2 chirps, then 1 chirp, medium pitch single chirps, high pitch 2 chirps, then 1 chirp, high pitch
Base Alarm Type
Granit XP User Guide
Scanner Alarm Type
55
Scanner Power Time-Out Timer
When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner power time-out barcode to change the time-out duration (in seconds).
Note: Scanning zero (0) is the equivalent of setting no time-out.
If there are no trigger pulls during the timer interval, the scanner goes into power down mode. Whenever the trigger is enabled, the timer is reset. The scanner will not go into power down mode when it is in the base and charging. Default = 3600 seconds.
0 seconds
200 seconds
400 seconds
* 3600 seconds
900 seconds
7200 seconds
Note: When the scanner is in power down mode, press the trigger to power the unit back up. There will be a set of power up beeps and a delay of up to a few seconds for the radio to join. The scanner will then be ready to use.
56
Granit XP User Guide
Flexible Power Management
If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn down the power output of the scanner. This reduces the range between the scanner and a base or an Access Point as shown in the following illustration:
802.11 LAN
Scanner
Reduced Power
Full Power
Granit XP 1990i and 1991i
Scan one of the barcodes below to set the scanner's power output to Full Power (100%), Medium Power (35%), Medium Low Power (5%), or Low Power (1%). Default = Full Power.
For Bluetooth Class 1 operation, use Full Power.
For Bluetooth Class 2 operation, use Medium Power or lower.
For BLE operation, use Medium Power.
* Full Power Medium Low Power
Medium Power Low Power
Granit XP User Guide
57
Batch Mode
Batch mode is used to store barcode data when a scanner is out of range of its base or Access Point, or when performing inventory. The data is transmitted to the base or Access Point once the scanner is back in range or when the records are manually transmitted.
Note: Batch Mode is only supported by the Honeywell Charge and Communication Base (CCB) and Honeywell Access Point (AP). Batch mode has limitations when using multiple scanners to one base or Access Point. If a cordless system is being used in "multiple link mode," where up to 3 scanners are to be connected to one base or Access Point, some accumulated or batched scans could be lost if scanners are constantly being moved in and out of range.
Automatic Batch Mode stores barcode data when the scanner is out of range of the base or Access Point. The data is automatically transmitted to the base or Access Point once the scanner is back in range. When the scanner's buffer space is full, any barcodes scanned generate an error tone. In order to scan barcodes again, the scanner must be moved back into range of the base or Access Point so data can be transmitted.
Inventory Batch Mode stores barcode data, whether or not you are in range of the base or Access Point. To transmit the stored data to the base or Access Point, either place the scanner in the base, or scan Transmit Inventory Records (page 63). When the scanner's buffer space is full, any barcodes scanned generate an error tone. In order to scan barcodes again, the data must be transmitted to the base or Access Point. Once the data is transmitted, it is cleared in the scanner.
Persistent Batch Mode is the same as Inventory Batch Mode, except that once the data is transmitted to the base or Access Point, it is retained in the scanner. If you want to transmit more than once, you can do so using this mode. In order to clear the scanner's buffer, you must scan Clear All Codes (see page 62).
Default = Batch Mode Off.
* Batch Mode Off Inventory Batch Mode
58
Automatic Batch Mode
Persistent Batch Mode
Granit XP User Guide
Batch Mode Beep
When scanning in Inventory Batch Mode (page 58), the scanner beeps every time a barcode is scanned. When Batch Mode Beep is On, you will also hear a click when each barcode is sent to the host. If you do not want to hear these clicks, scan Batch Mode Beep Off. Default = Batch Mode Beep On.
Batch Mode Beep Off
* Batch Mode Beep On
Batch Mode Storage
When a scanner is storing data during a Batch Mode process, you can select whether the data is stored in Flash memory or in RAM. Flash Storage: The scanner writes any untransmitted data to flash memory prior to powering down. The data will still be there when the scanner powers back up. However, the scanner will power down, even with untransmitted data, if it reaches a power down timeout or if the battery or charge pack power is very low. RAM Storage: The scanner will not power down while it contains data that has not been transmitted to the base or Access Point, even if it reaches a power down timeout. However, if the scanner runs out of power, it will power down and the data will be lost. Default = Flash Storage.
* Flash Storage
RAM Storage
Granit XP User Guide
59
Batch Mode Quantity
When in Batch Mode, you may wish to transmit the number of multiple barcodes scanned, rather than a single barcode multiple times. For example, if you scan three barcodes called XYZ with Batch Mode Quantity Off, when you transmit your data it will appear as XYZ three times. Using Batch Mode Quantity On and the Quantity Codes (page 61), you could output your data as "XYZ, 00003" instead.
Note: If you wish to format your output, for example, place a CR or tab between the barcode data and the quantity, refer to Data Format beginning on page 119.
Default = Batch Mode Quantity Off.
* Batch Mode Quantity Off
Batch Mode Quantity On
Enter Quantities
Quantity Codes (page 61) allow you to enter a quantity for the last item scanned, up to 9999 (default = 1). Quantity digits are shifted from right to left, so if a fifth digit is scanned, the first digit scanned is discarded and the second, third and fourth digits are moved to the left to accommodate the new digit. For example, if the Quantity 5 barcode is scanned after the quantity has been set to 1234, then the 1 is dropped, the quantity will be 2345.
Example: Add a quantity of 5 for the last item scanned.
1. Scan the item's barcode. 2. Scan the quantity 5 barcode.
Example: Add a quantity of 1,500 for the last item scanned.
1. Scan the item's barcode. 2. Scan the quantity 1 barcode. 3. Scan the quantity 5 barcode. 4. Scan the quantity 0 barcode. 5. Scan the quantity 0 barcode.
Example: Change a quantity of 103 to 10. To correct an incorrect quantity, scan the quantity 0 barcode to replace the incorrect digits, then scan the correct quantity barcodes.
60
Granit XP User Guide
1. Scan the quantity 0 barcode to change the quantity to 1030. 2. Scan the quantity 0 barcode to change the quantity to 0300. 3. Scan the quantity 1 barcode to change the quantity to 3001. 4. Scan the quantity 0 barcode to change the quantity to 0010. Default = 1.
Quantity Codes
0
* 1
2
3
4
5
6
7
8
9
Granit XP User Guide
61
Batch Mode Output Order
When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out). Default = Batch Mode FIFO.
* Batch Mode FIFO
Batch Mode LIFO
Total Records
If you wish to output the total number of barcodes scanned when in Batch Mode, scan Total Records.
Total Records
Delete Last Code
If you want to delete the last barcode scanned when in Batch Mode, scan Delete Last Code.
Delete Last Code
Clear All Codes
If you want to clear the scanner's buffer of all data accumulated in Batch Mode, scan Clear All Codes.
Clear All Codes
62
Granit XP User Guide
Transmit Records to Host
If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 58), you must scan the following barcode to transmit all the stored data to the host system.
Transmit Inventory Records
Batch Mode Transmit Delay
Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process. To program a transmit delay between accumulated scans, scan one of the following delays. Default = Off. Note: In most cases, a short (250 ms (milliseconds)) delay is ideal, however, longer delays may be programmed. Contact Technical Support (page xiii) for additional information.
* Batch Mode Transmit Delay Off (No Delay)
Batch Mode Transmit Delay Short (250 ms)
Batch Mode Transmit Delay Medium (500 ms)
Batch Mode Transmit Delay Long (1000 ms)
Multiple Scanner Operation
Note: Multiple Scanner Operation Mode allows you to link up to 3 scanners to one base or Access Point. You cannot join an 4th scanner until you unlink one of the 3 scanners or take a scanner out of range.
Granit XP User Guide
63
To put the scanner in multiple scanner mode, scan the barcode below. Once you scan this barcode, the scanner is unlinked from the base or Access Point and must either be placed into the base, or you must scan the Access Point linking barcode in order to relink.
Multiple Scanner Operation
Scanner Name
You may assign a name to each scanner you are using for identification purposes. For example, you may want to have a unique identifier for a scanner that is receiving imaging commands sent from the base or Access Point.
The default name is in the format "ScannerName_Model_SN_XXXXXXXXXX" If you have more than one scanner linked to a base, and they all have the same name, the first scanner linked to the base receives commands. When renaming a series of scanners with identical names, unlink all except one of the scanners from the base.
Perform the rename operation using either the barcodes on page 65, or by sending the serial command :ScannerName:BT_NAMNewName. where ScannerName is the current name of the scanner, and NewName is the new name for the scanner. If you wish to change the names of additional scanners, link them one at a time and repeat the :ScannerName:BT_NAMNewName. command for each scanner.
To rename scanners with sequential numeric names, scan the barcodes below. Scan the Reset code after each name change and wait for the scanner to relink to the base or Access Point before scanning a barcode to rename the next scanner.
0001 0003
0002 Reset
64
Granit XP User Guide
You may also scan the Scanner Name barcode below and scan a number for the scanner name. For example, if you wanted to name the linked scanner "312," you would scan the barcode below, scan the 3, 1, and 2 barcodes on the Programming Chart, beginning on page 291, then Save. Scan the Reset barcode and wait for the scanner to relink to the base.
Scanner Name
Application Work Groups
Your cordless system can have up to 3 scanners linked to one base or Access Point. You can also have up to 3 work groups. If you want to have all of the scanners' settings programmed alike, you don't need to use more than one work group. If you want each scanner to have unique settings (e.g., beeper volume, prefix/suffix, data formatter), then you may program each scanner to its own unique work group and may program each scanner independently. For example, you might want to have multiple work groups in a retail/warehouse application where you need to have different data appended to barcodes used in the warehouse area versus the retail area. You could assign all the scanners in the retail area to one work group and those in the warehouse to another. Consequently, any desired changes to either the retail or warehouse area would apply to all scanners in that particular work group. Honeywell's online configuration tool, EZConfig-Scanning (page 224), makes it easy for you to program your system for use with multiple scanners and multiple work groups.
The scanner keeps a copy of the menu settings it is using. Whenever the scanner is connected or reconnected to a base or an Access Point, the scanner is updated with the latest settings from the base or Access Point for its work group. The scanner also receives menu setting changes processed by the base or Access Point. If a scanner is removed from a base or an Access Point and placed into another base or linked to another Access Point, it will be updated with the new base/Access Point settings for whatever work group to which that the scanner was previously assigned. For example, if the scanner was in work group 1 linked to the first base, it will be placed in work group 1 in the second base with the associated settings.
Application Work Group Selection
This programming selection allows you to assign a scanner to a work group by scanning the barcode below. You may then program the settings (e.g., beeper volume, prefix/suffix, data formatter) that your application requires. Default = Group 0.
* Group 0
Granit XP User Guide
65
Group 1
Group 2
Reset the Factory Defaults: All Application Work Groups
The following barcode defaults all of the work groups to the factory default settings.
PAPDFT&
Factory Default Settings: All Work Groups
To see what the factory default settings are, refer to the table of Menu Commands, beginning on page 232. The standard product default settings for each of the commands are indicated by an asterisk (*). Note: Scanning this barcode also causes both the scanner and the base or Access Point to perform a reset and become unlinked. The scanner must be placed in the base, or the Access Point linking barcode must be scanned to re-establish the link. Refer to Scanner Modes, page 52 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping while all scanners are relinked to the base or Access Point and the settings are changed.
66
Granit XP User Guide
Reset the Custom Defaults: All Application Work Groups
If you want the custom default settings restored to all of the work groups, scan the Custom Product Default Settings barcode below. (If there are no custom defaults, it will reset the work groups to the factory defaults.) See Set Custom Defaults on page 11 for further information about custom defaults.
Custom Default Settings: All Work Groups
Note: Scanning this barcode also causes both the scanner and the base or Access Point to perform a reset and become unlinked. The scanner must be placed in its base, or the Access Point linking barcode must be scanned to re-establish the link. Refer to Scanner Modes, page 52 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping while all scanners are relinked to the base or Access Point and the settings are changed.
Use the Scanner with Bluetooth Devices
The scanner can be used either with the charge base or with other Bluetooth devices. Those devices include personal computers, laptops, PDAs, and Honeywell mobility systems devices.
Bluetooth Secure Simple Pairing (SSP)
Secure Simple Pairing (SSP) allows you to connect simply and securely to other Bluetooth devices without having to enter a PIN code (as described in Connect with Bluetooth Device Directly procedure). SSP is only available when using Bluetooth version 2.1 or higher. When SSP is on, no PIN is required for pairing. Turn SSP off if you are connecting to a Bluetooth device that is not using a compatible Bluetooth version. Default = Bluetooth SSP On.
* Bluetooth SSP On
Bluetooth SSP Off
Granit XP User Guide
67
Connect with Bluetooth Device Directly
Your scanner can be paired with Bluetooth-capable devices, such as personal computers, laptops, and tablets, so that scanned data appears on your device screen as though it was entered on the keyboard. In order to pair with the Bluetooth device:
1. Scan the appropriate Bluetooth HID Keyboard Connect barcode below.
Bluetooth HID Keyboard Connect
Bluetooth HID Japanese Keyboard Connect
2. Set your personal computer, laptop or tablet so it searches for other Bluetooth devices. (Refer to your device's User Guide for pairing instructions.)
3. Select the scanner name on your device. Some devices will automatically pair with the scanner. If your device pairs automatically with the scanner, it displays a successful pairing message and you do not need to continue to the next step.
4. If your device does not automatically pair with the scanner, a PIN is displayed. This PIN must be scanned within 60 seconds. Quickly scan Bluetooth PIN Code below, then scan the numeric barcode(s) for the PIN code from the chart below, then scan Save.
Bluetooth PIN Code 0
1 2
3
68
Granit XP User Guide
4
5
6
7
8
9
Save
Virtual Keyboard
Once your scanner has been connected directly to an iPad, smart phone, or laptop, you can toggle the virtual keyboard on your device with a quick double pull of the scanner trigger. Default = Enable.
Disable
* Enable
Granit XP User Guide
69
Bluetooth HID Keyboard Disconnect
If your scanner has been connected directly to an iPad, smart phone, or laptop, you must disconnect it in order to once again communicate with the base or Access Point. Scan the Bluetooth HID Keyboard Disconnect barcode to unlink the scanner from the currently linked host. Scan the linking barcode on the base or Access Point to relink the scanner.
Bluetooth HID Keyboard Disconnect
Bluetooth Serial Port - PCs/Laptops
Scanning the Non-Base BT Connection barcode below unlinks your scanner and puts it into a discoverable state. Once the scanner searches for and connects with a Bluetooth host, the scanner stores the connection to the host device address and switches virtual COM ports. This allows the scanner to automatically relink to the host if the connection is lost.
Non-Base BT Connection
PDAs/Mobility Systems Devices
You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the barcode below and follow the instructions supplied with your Bluetooth device to locate the scanner, and connect with it.
BT Connection - PDA/Mobility Systems Device
Change the Scanner's Bluetooth PIN Code
Some devices require a PIN code as part of the Bluetooth security features. Your scanner's default PIN is 1234, which you may need to enter the first time you connect to your PDA or PC. The PIN code must be between 1 and 16 characters. To change the PIN, scan the barcode below and then scan the appropriate numeric barcodes from the Programming Chart, beginning on page 291, then Save.
Bluetooth PIN
70
Granit XP User Guide
Minimize Bluetooth/ISM Band Network Activity
The settings described below can help you customize the relinking behavior of the cordless area-imaging system to obtain the best compromise between convenience and low interference.
Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks, cordless phones, and Bluetooth.
Auto Reconnect Mode
Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of connection is detected. When the Auto Reconnect On barcode is scanned, the scanner begins the relink process immediately, without user intervention. Default = Auto Reconnect On.
* Auto Reconnect On
Auto Reconnect Off
The table below shows the results of the Auto Reconnect On and Off settings:
Event Scanner out of range
Base or Access point reset (firmware upgrade or power cycle) Scanner power down due to Power Time-Out Timer setting Scanner reset due to firmware upgrade Scanner reset due to battery or charge pack change
Auto Reconnect On
Auto Reconnect Off
Relink occurs automatically. If maximum number of link attempts is unsuccessful, then the scanner must be relinked by either pulling the trigger, placing the scanner in the base, or scanning the Access Point linking barcode. (See Maximum Link Attempts on page 72.)
The scanner is relinked by pulling the trigger, or scanning the Access Point linking barcode.
Scanner behaves as if out of range.
No attempt to relink made while base or Access Point is powered off. Trigger must be pulled to initiate relinking.
Trigger must be pulled, Access Point linking barcode must be scanned, or the scanner must be placed in the base unit to relink. (Note: Scanner re-links on power up, but powers on due to one of the above actions.)
Relink occurs automatically.
Relink occurs automatically.
Granit XP User Guide
71
Event
Scanner placed in different base unit
Auto Reconnect On
Auto Reconnect Off
Relink to new base occurs automatically.
Maximum Link Attempts
The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base or an Access Point. During the connection setup process, the scanner transmits in order to search for and connect to a base or an Access Point. In order to prevent continuous transmissions that could interfere with other users of the ISM band, the number of attempts to connect is limited by this setting. After the maximum number of attempts is reached, the scanner will not attempt to reconnect to a base or an Access Point. Pressing the trigger, scanning an Access Point linking barcode, or placing the scanner in the cradle resets the attempt count and the scanner will again try to link.
Scan the Maximum Link Attempts barcode, then scan the number of attempts for the setting (from 0-100) from theProgramming Chart, beginning on page 291, then Save. Default = 0.
Maximum Link Attempts
Note: When Auto Reconnect Mode is On, setting Maximum Link Attempts to zero will cause the scanner to try to link until the Power Time-Out Timer setting expires. When Auto Reconnect Mode is Off, setting Maximum Link Attempts to zero will cause the scanner to only attempt linking one time after a trigger press.
Relink Time-Out
Relink Time-Out controls the idle time between relink attempts. An attempt to link a scanner to a base or an Access Point typically lasts up to 5 seconds. This is the time when the scanner is actually attempting a contact. Relink Time-Out controls the amount of time, in seconds, that elapses between the end of one connection attempt and the start of the next.
Note: The length of time for an attempt depends on the number of scanners connected to a base unit or Access Point. An extra 7 seconds may be required when a connection is successful.
Scan the Relink Time-Out barcode, then scan the number of seconds for the setting (from 1-100) from the Programming Chart, beginning on page 291, then Save. Default = 3 seconds.
Relink Time-Out
72
Granit XP User Guide
Bluetooth/ISM Network Activity Examples
Default values
When the scanner goes out of range, the scanner repeatedly attempts to connect to the base unit or Access Point. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After one hour, the scanner powers off and batch mode data is lost.
Example: Maximum Link Attempts set to 15 Other values at default setting
When the scanner goes out of range, 15 attempts are made to link to the base unit or Access Point. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base or Access Point, but retains any barcodes that may have been saved in batch mode. After one hour, the scanner powers off and batch mode data is lost.
Example: Auto Reconnect Mode set to 0 Maximum Link Attempts set to 15 Other values at default setting
When the scanner goes out of range, no action is taken to relink. When the trigger is pulled, 15 attempts are made to link to the base or Access Point. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base or Access Point, but retains any barcodes that may have been saved in batch mode. After one hour, the scanner powers off and batch mode data is lost. Refer to Auto Reconnect Mode, page 71, to review other events that can start the relink process.
Example: Auto Reconnect Mode set to 1 Maximum Link Attempts set to 0 Relink Time-Out set to 10 Scanner Power Time-Out Timer set to 1800
Note: See Scanner Power Time-Out Timer on page 56.
The scanner attempts to connect to the base or Access Point every 15 seconds, measured from one attempt start to the next attempt start. After one half hour, the scanner powers off.
Host Acknowledgment
Some applications require that the host terminal (or server) validate incoming barcode data (database look-up) and provide acknowledgment to the scanner whether or not to proceed. In Host ACK Mode, the scanner waits for this acknowledgment after each scan. Visual and audible acknowledgments provide valuable
Granit XP User Guide
73
feedback to the scan operator. The Host ACK functionality is controlled via a number of pre-defined escape commands that are sent to the scanner to make it behave in different ways.
Note: System performance degrades when using Host ACK at rates lower than 9600 baud.
The following criteria must be met for the Host ACK to work correctly:
· The cordless system must be configured for Host Port RS232 (terminal ID = 000 or USB COM Emulation (terminal ID = 130).
· RTS/CTS is defaulted off. You must enable it if the host system requires it.
· Host ACK must be set to On (page 75).
· A comma must be used as a terminator.
· The host terminal software must be capable of interpreting the barcode data, make decisions based on the data content, and send out appropriate escape commands to the scanner.
Escape commands are addressed to the scanner via "Application Work Groups." Once a command is sent, all scanners in a group respond to that command. Because of this, it is recommended that each scanner is assigned to its own group in Host ACK mode.
The commands to which the scanner responds are listed on page 75. The [ESC] is a 1B in hex. A typical command string is y [ESC] x, where "y" is the application work group number, "[ESC] x" is the escape command, and the comma is the terminator, which is required. (When "y" is not specified, the command is sent to the default Application Work Group 0.)
Example: Commands may be strung together to create custom response sequences. An example of a command string is listed below.
[ESC]4,[ESC]5,[ESC]6,
The above example will make a scanner that is in application work group zero beep low, then medium, then high.
Example: A good read beep is required for any item on file, but a razz or error tone is required if the item is not on file. In this case,
[ESC]7, is sent from the host to the scanner for an on-file product
[ESC]8,[ESC]8, is sent from the host to the scanner for a not-on-file product
When a barcode is scanned, the scanner enters a timeout period until either the host ACK sequence is received, or the timeout expires (in 10 seconds, by default).
Once Host ACK is enabled, the system works as follows when a barcode is scanned:
· The scanner reads the code and sends data to the base or Access Point to transmit to the host system. No audible or visual indication is emitted until the scanner receives an escape command. The scanner read illumination goes out when there's a successful read.
74
Granit XP User Guide
· Scanner operation is suspended until 1) a valid escape string is received from the host system or 2) the scanner times out.
· Once condition 1 or 2 above has been met, the scanner is ready to scan again, and the process repeats.
A time-out occurs if the scanner does not receive a valid escape command within 10 seconds. A time-out is indicated by an error tone. If a time-out occurs, the operator should check the host system to understand why a response to the scanner was not received.
Host ACK On/Off
Host ACK On
* Host ACK Off
Host ACK Timeout
You can set a timeout for the length of time the scanner waits for a valid escape command when using Host Acknowledgment Mode. Set the length (in seconds) for a timeout by scanning the following barcode, then setting the timeout (from 1-90 seconds) by scanning digits from the Programming Chart, beginning on page 291, then Save. Default = 10.
Host ACK Responses
Command [ESC] a, [ESC] b, [ESC] 1, [ESC] 2, [ESC] 3, [ESC] 4, [ESC] 5, [ESC] 6,
Host ACK Timeout
Action Double beeps to indicate a successful menu change was made. Razz or error tone to indicate a menu change was unsuccessful. The green LED illuminates for 135 milliseconds followed by a pause. The green LED illuminates for 2 seconds followed by a pause. The green LED illuminates for 5 seconds followed by a pause. Emits a beep at a low pitch. Emits a beep at a medium pitch. Emits a beep at a high pitch.
Granit XP User Guide
75
Command [ESC] 7, [ESC] 8,[ESC] 8,
Action
Beeps to indicate a successful decode and communication to host. Razz or error tone to indicate a decode/communication to host was unsuccessful.
76
Granit XP User Guide
CHAPTER
4 INPUT/OUTPUT SETTINGS
Power Up Beeper
The scanner can be programmed to beep when it's powered up. If you are using a cordless system, the base can also be programmed to beep when it is powered up. Scan the Off barcode(s) if you don't want a power up beep. Default = Power Up Beeper On - Scanner.
Power Up Beeper Off Scanner
* Power Up Beeper On Scanner
Power Up Beeper Off Cordless Base
Power Up Beeper On Cordless Base
Granit XP User Guide
77
Beep on BEL Character
You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On barcode below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off.
*Beep on BEL Off
Beep on BEL On
Trigger Click
To hear an audible click every time the scanner trigger is pressed, scan the Trigger Click On barcode below. Scan the Trigger Click Off code if you don't wish to hear the click. (This feature has no effect on serial or automatic triggering.) Default = Trigger Click Off.
*Trigger Click Off
Trigger Click On
Good Read and Error Indicators
Beeper Good Read
The beeper may be programmed On or Off in response to a good read. Turning this option off only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = Beeper - Good Read On.
Beeper - Good Read Off
78
* Beeper - Good Read On
Granit XP User Guide
Beeper Volume Good Read
The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High.
Low
Medium
* High
Off
Beeper Pitch Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium.
Low (1600 Hz)
* Medium (2700 Hz)
High (4200 Hz)
Granit XP User Guide
79
Vibrate Good Read
The scanner vibrates once when a barcode is successfully read, and twice when a programming barcode is successfully read. When a programming barcode is unsuccessful, the scanner emits one long vibration (2 times the Vibrate Duration length). Scan Vibrate - Good Read Off to keep the scanner from vibrating. Default = Vibrate - Good Read On.
Vibrate- Good Read Off
*Vibrate- Good Read On
Vibrate Duration
If you want to set the length for the good read vibration, scan the barcode below, then set the duration (from 100 - 2,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save. Default = 100 ms.
Vibrate Duration
Beeper Pitch Error
The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = Razz.
* Razz (250 Hz) High (4200 Hz)
Medium (3250 Hz)
80
Granit XP User Guide
Beeper Duration Good Read
The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal.
* Normal Beep
Short Beep
LED Good Read
The LED indicator can be programmed On or Off in response to a good read. Default = On.
* LED - Good Read On
LED - Good Read Off
Number of Beeps Good Read
The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read. The beeps and LED flashes are in sync with one another. To change the number of beeps, scan the barcode below and then scan a digit (1-9) barcode from the Programming Chart, beginning on page 291, then Save. Default = 1.
Number of Good Read Beeps/LED Flashes
Number of Beeps Error
The number of beeps and LED flashes emitted by the scanner for a bad read or error can be programmed from 1 - 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response
Granit XP User Guide
81
to an error. To change the number of error beeps, scan the barcode below and then scan a digit (1-9) barcode from the Programming Chart, beginning on page 291, then Save. Default = 1.
Number of Error Beeps/LED Flashes
Good Read Delay
This sets the minimum amount of time before the scanner can read another barcode. Default = 0 ms (No Delay).
* No Delay
Short Delay (500 ms)
Medium Delay (1,000 ms)
Long Delay (1,500 ms)
User-Specified Good Read Delay
If you want to set your own length for the good read delay, scan the barcode below, then set the delay (from 0 - 30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save.
User-Specified Good Read Delay
82
Granit XP User Guide
Trigger Modes
Manual Trigger
When in manual trigger mode, the scanner scans until a barcode is read, or until the trigger is released. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode. Enhanced mode is best used when you require a very fast scan speed and don't require a long working range. Default = Manual TriggerNormal.
* Manual Trigger - Normal
Manual Trigger Enhanced
Trigger Toggle
Trigger Toggle mode lets you quickly hit the trigger two or three times to put the scanner into either imaging mode or centering mode, then toggle back to scanning. So, like a double-click with a mouse, you can control what the next scanner's action will be. For example, you could double-press the trigger to go into imaging mode, then the next trigger press takes the image. The scanner then reverts to scanning mode. Use the following codes to configure what action you would like the scanner to take when in Trigger Toggle mode. Default = Trigger Toggle Off.
*Trigger Toggle Off Trigger Toggle - Centering
Trigger Toggle - Image Capture
Granit XP User Guide
83
Trigger Number
This sets the number of trigger presses required to activate the Trigger Toggle Mode. Default = 3.
2 Quick Triggers
*3 Quick Triggers
4 Quick Triggers
Trigger Timing
This sets the timing of the trigger presses in order to qualify as a trigger toggle, rather than a regular trigger press. After scanning the Trigger Timing barcode, set the time-out duration (from 50-2,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save. Default = 400ms.
Trigger Timing
Trigger Toggle Timeout
This sets the length of time the scanner stays in trigger toggle mode before reverting to scan mode. After scanning the Trigger Toggle Timeout barcode, set the time-out duration (from 0 to 65 seconds) by scanning digits from the Programming Chart, beginning on page 291, then Save. Default = 5 seconds. Note: If this is set to 0, you must repeat the toggle sequence to return to the default scanning mode. For example, if 2 quick trigger presses puts the scanner into centering mode and the Trigger Timing is 0, you would have to do 2 quick presses again to go back to the default scanning mode.
Trigger Toggle Timeout
84
Granit XP User Guide
Serial Trigger
You can activate the scanner either by pressing the trigger, or using a serial trigger command (see Trigger Commands on page 230). You must be in a serial interface mode in order to use serial triggering. Refer to RS232 Serial Port (page 14) or USB Serial (page 16) for further information. When in serial mode, the scanner scans until a barcode has been read or until the deactivate command is sent. The scanner can also be set to turn itself off after a specified time has elapsed (see Read TimeOut, which follows).
Read Time-Out
Use this selection to set a time-out (in milliseconds) of the scanner's trigger when using serial commands to trigger the scanner. Once the scanner has timed out, you can activate the scanner either by pressing the trigger or using a serial trigger command. After scanning the Read Time-Out barcode, set the time-out duration (from 0-300,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save. Default = 30,000 ms.
Read Time-Out
Trigger Mode 11
Trigger Mode 11 provides an option for improved barcode targeting control. When activated, this enables the user to squeeze the trigger to activate only the aimer for precise targeting, then release the trigger to scan the selected barcode. Combined with Single Code Centering, this can improve performance for scanning specific barcodes in regions with many barcodes present, or for precisely selecting and scanning barcodes at a distance.
Aimer will be pre-lit when trigger is pressed and scanning occurs when trigger is released until a good scan or normal scan timeout. Default = Disable.
* Disable
Enable
Granit XP User Guide
85
Presentation Mode
Presentation Mode uses ambient light and scanner illumination to detect barcodes. When in Presentation Mode, the LEDs remain dim until a barcode is presented to the scanner, then the aimer turns on and the LEDs turn up to read the code. If the light level in the room is not high enough, Presentation Mode may not work properly
Note: Cordless Granit XP scanners can only be used in presentation mode powered by the battery; this mode cannot be used while docked.
Scan the following barcode to program your scanner for Presentation Mode.
Presentation Mode
Triggered Presentation Mode
This mode uses light to detect the presence of an object. Default = Ambient and Scanner Light.
Ambient Light Only
*Ambient and Scanner Light
Presentation LED Behavior after Decode
When a scanner is in presentation mode, the LED aimer dims 30 seconds after a barcode is decoded. If you wish to dim the LED aimer immediately after a barcode is decoded, scan the LEDs Off barcode, below. Default = LEDs On.
* LEDs On
LEDs Off
86
Granit XP User Guide
Presentation Centering
Use Presentation Centering to narrow the scanner's field of view when it is in the stand to make sure the scanner reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will insure that only the desired codes are read.
Note: To adjust centering when the scanner is hand-held, see Laser Aimer - Scan Duration (page 4-97).
If a barcode is not touched by a predefined window, it will not be decoded or output by the scanner. If Presentation Centering is turned on by scanning Presentation Centering On, the scanner only reads codes that pass through the centering window you specify using the Top of Presentation Centering Window, Bottom of Presentation Centering Window, Left, and Right of Presentation Centering Window barcodes.
In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Barcode 1 passes through the centering window, it will be read. Barcode 2 does not pass through the centering window, so it will not be read.
0% Barcode 1
10 20
Barcode 2
30
40
50
60
70
80
90
100 0
10 20 30 40 50 60 70 80 90 100%
Note: A barcode needs only to be touched by the centering window in order to be read. It does not need to pass completely through the centering window.
Granit XP User Guide
87
Scan Presentation Centering On, then scan one of the following barcodes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window from the Programming Chart, beginning on page 291, then Save. Default Presentation Centering = 40% for Top and Left, 60% for Bottom and Right.
Presentation Centering On
Top of Presentation Centering Window
* Presentation Centering Off
Bottom of Presentation Centering Window
Left of Presentation Centering
Window
Right of Presentation Centering Window
For more information, see Single Code Centering on page 98.
Near-Far Camera Modes (XR & XLR Models only)
The scanner provides extended depth-of-field on many codes through the use of two cameras.
Camera Selection
By default, the two cameras operate by automatically switching between near and far, as needed. Near Camera Only or Far Camera Only selects only one camera, near or far. Automatic Switching will switch between both near and far cameras with steady illumination. Alternate Switching will alternate cameras with extra far field illumination. Default = Automatic Switching.
88
Granit XP User Guide
Near Camera Only
Far Camera Only
* Automatic Switching
Alternate Switching
Camera Sensors
The far camera has various depth positions. If you need to adjust the position, scan the appropriate barcode below. Default = All Positions.
Far Position
Medium Position
Near Position
* All Positions
Camera Illumination
The camera illumination can be set to fixed, alternate, and automatic. While in Fixed Illumination you can select Near Camera or Far Camera. Default = Fixed Illumination and Far Camera.
Granit XP User Guide
89
* Fixed Illumination
Near Camera
* Far Camera
In Alternate Illumination the illumination alternates between near and far.
Alternate Illumination
In Automatic Illumination, the illumination will automatically switch to far illumination when images are too dark.
Automatic Illumination
Poor Quality Codes
Poor Quality 1D Codes
This setting improves the scanner's ability to read damaged or badly printed linear barcodes. When Poor Quality 1D Reading On is scanned, poor quality linear barcode reading is improved, but the scanner's snappiness is decreased, making it less aggressive when reading good quality barcodes. This setting does not affect 2D barcode reading. Default = Poor Quality 1D Reading Off.
Poor Quality 1D Reading On
90
* Poor Quality 1D Reading Off
Granit XP User Guide
Poor Quality PDF Codes
This setting improves the scanner's ability to read damaged or badly printed PDF codes by combining information from multiple images. It is useful when a complete barcode cannot be seen in one image. This setting does not affect 1D barcode reading. Default = Poor Quality PDF Reading On.
*Poor Quality PDF Reading On
Poor Quality PDF Reading Off
Low Resolution PDF Codes
This setting improves the scanner's ability to read low resolution PDF codes. When Low Resolution PDF Codes On is scanned, poor quality PDF code reading is improved, but the scanner's snappiness is decreased, making it less aggressive when reading good quality barcodes. This setting does not affect 1D barcode reading. Default = Low Resolution PDF Codes Off.
Low Resolution PDF Codes On
* Low Resolution PDF Codes Off
CodeGateTM
When CodeGate is On, the trigger is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding barcodes, but the barcode data is not transmitted until the trigger is pressed. When CodeGate is Off, barcode data is transmitted when it i decoded. Default = CodeGate Off.
* CodeGate Off
Granit XP User Guide
91
CodeGate On
Streaming PresentationTM Mode
When in Streaming Presentation mode, the scanner's aimer goes out after a short time, but the scan illumination remains on all the time to continuously search for barcodes. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode. Enhanced mode is best used when you require a very fast scan speed and don't require a long working range.
Streaming Presentation Mode - Normal
Streaming Presentation Mode - Enhanced
When using Preferred Symbology, a lower priority symbol must be centered on the aiming pattern to be read in Streaming Presentation Mode.
Note: Cordless Granit XP scanners can only be used in presentation mode powered by the battery; this mode cannot be used while docked.
Hands Free Time-Out
The Scan Stand and Presentation Modes are referred to as "hands free" modes. If the scanner's trigger is pulled when using a hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual trigger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger pulls) the scanner reverts to the original hands free mode. Scan the Hands Free Time-Out barcode, then scan the time-out duration (from 0300,000 milliseconds) from the Programming Chart, beginning on page 291, then Save. Default = 5,000 ms.
Hands Free Time-Out
92
Granit XP User Guide
Reread Delay
This sets the time period before the scanner can read the same barcode a second time. Setting a reread delay protects against accidental rereads of the same barcode. Longer delays are effective in minimizing accidental rereads. Use shorter delays in applications where repetitive barcode scanning is required. Reread Delay only works when in a Presentation Mode (see page 86). Default = Medium.
Short (500 ms)
* Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms)
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the barcode below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save.
User-Specified Reread Delay
2D Reread Delay
Sometimes 2D barcodes can take longer to read than other barcodes. If you wish to set a separate Reread Delay for 2D barcodes, scan one of the programming codes that follows. 2D Reread Delay Off indicates that the time set for Reread Delay is used for both 1D and 2D barcodes. Default = 2D Reread Delay Off.
* 2D Reread Delay Off
Granit XP User Guide
93
Medium (2000ms)
Short (1000ms)
Long (3000ms)
Extra Long (4000ms)
Character Activation
You may use a character sent from the host to trigger the scanner to begin scanning. When the activation character is received, the scanner continues scanning until either the Character Activation Timeout (page 95) is reached, the deactivation character is received (see Deactivation Character on page 96), or a barcode is transmitted. Scan the On barcode to use character activation, then use Activation Character (page 94) to select the character you will send from the host to start scanning. Default = Off.
* Off
On
Activation Character
This sets the character used to trigger scanning when using Character Activation Mode. On the ASCII Conversion Chart (Code Page 1252), page 282, find the hex value that represents the character you want to use to trigger scanning. Scan the following barcode, then use the Programming Chart to read the alphanumeric combination that represents that ASCII character. Scan Save to finish. Default = 12 [DC2].
Activation Character
94
Granit XP User Guide
End Character Activation After Good Read
After a barcode is successfully detected and read from the scanner, the illumination can be programmed either to remain on and scanning, or to turn off. When End Character Activation After Good Read is enabled, the illumination turns off and stops scanning after a good read. If you scan Do Not End Character Activation After Good Read, the illumination remains on after a good read.
Do Not End Character Activation After Good Read
End Character Activation After Good Read
Character Activation Timeout
You can set a timeout for the length of time the illumination remains on and attempting to decode barcodes when using Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following barcode, then setting the timeout (from 1-300,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save. Default = 30,000 ms.
Character Activation Timeout
Character Deactivation
If you have sent a character from the host to trigger the scanner to begin scanning, you can also send a deactivation character to stop scanning. Scan the following On barcode to use character deactivation, then use Deactivation Character (following) to select the character you will send from the host to terminate scanning. Default = Off.
* Off
On
Granit XP User Guide
95
Deactivation Character
This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion Chart (Code Page 1252), page 282, find the hex value that represents the character you want to use to terminate scanning. Scan the following barcode, then use the Programming Chart, beginning on page 291 to read the alphanumeric combination that represents that ASCII character. Scan Save to finish. Default = 14 [DC4].
Deactivation Character
Illumination Lights
If you want the illumination lights on while reading a barcode, scan the Lights On barcode, below. However, if you want to turn just the lights off, scan the Lights Off barcode. Default = Lights On. Note: This setting does not affect the aimer light. The aiming light can be set using Aimer Mode (page 97).
* Lights On
Lights Off
Aimer Delay
The aimer delay allows a delay time for the operator to aim the scanner before the picture is taken. Use these codes to set the time between when the trigger is pulled and when the picture is taken. During the delay time, the aiming light will appear, but the LEDs won't turn on until the delay time is over. Default = Off.
1 millisecond
250 milliseconds
96
Granit XP User Guide
500 milliseconds
* Off (no delay)
User-Specified Aimer Delay
If you want to set your own length for the duration of the delay, scan the barcode below, then set the time-out by scanning digits (0 - 4,000 ms) from the Programming Chart, beginning on page 291, then Save.
Delay Duration
Aimer Mode
This feature allows you to turn the aimer on and off. When the Interlaced barcode is scanned, the aimer is interlaced with the illumination LEDs. Default = Interlaced.
Off
* Interlaced
Laser Aimer - Scan Duration
Use the following barcodes to specify how long you want the laser aimer to remain on after the trigger is released. Scan the Laser Aimer - Scan Duration barcode to set a different duration, then set the duration by scanning digits (0 - 65,535 ms) from the Programming Chart, beginning on page 291. Scan Save to finish. Default = 10 seconds
*10 Second Scan Duration
Granit XP User Guide
97
Laser-Aimer Scan Duration
Centering
Use Centering to narrow the scanner's field of view to make sure that when the scanner is hand-held, it reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the desired codes are read. (Centering can be used in conjunction with Aimer Delay, page 96, for the most error-free operation in applications where multiple codes are spaced closely together. Using the Aimer Delay and Centering features, the scanner can emulate the operation of older systems, such as linear laser barcode scanners.)
Note: To adjust centering when the scanner is in a stand, see Presentation Centering (page 87).
Single Code Centering
Scan Single Code Centering to target the barcode closest to the center of the image. Singling out a barcode in this manner increases scanning accuracy when there are multiple barcodes close together.
Single Code Centering
Custom Centering
Use the following settings to customize your centering window. If a barcode is not touched by a predefined window, it will not be decoded or output by the scanner. If centering is turned on by scanning Centering On, the scanner only reads codes that pass through the centering window you specify using the Top of Centering Window, Bottom of Centering Window, Left, and Right of Centering Window barcodes.
98
Granit XP User Guide
Example: In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Barcode 1 passes through the centering window, it will be read. Barcode 2 does not pass through the centering window, so it will not be read.
0% Barcode 1
10
20
Barcode 2
30
40
50
60
70
80
90
100 0
10 20 30 40 50 60 70 80 90 100%
Note: A barcode needs only to be touched by the centering window in order to be read. It does not need to pass completely through the centering window.
Scan Centering On, then scan one of the following barcodes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits from the Programming Chart, beginning on page 291, then Save. Default Centering = 40% for Top and Left, 60% for Bottom and Right.
Centering On Top of Centering Window
* Centering Off
Granit XP User Guide
99
Left of Centering Window
Bottom of Centering Window Right of Centering Window
Preferred Symbology
The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both barcode symbologies appear on the same label, but the lower priority symbology cannot be disabled.
For example, you may be using the scanner in a retail setting to read U.P.C. symbols, but have occasional need to read a code on a drivers license. Since some licenses have a Code 39 symbol as well as the PDF417 symbol, you can use Preferred Symbology to specify that the PDF417 symbol be read instead of the Code 39.
Preferred Symbology classifies each symbology as high priority, low priority, or as an unspecified type. When a low priority symbology is presented, the scanner ignores it for a set period of time (see Preferred Symbology Time-out on page 101) while it searches for the high priority symbology. If a high priority symbology is located during this period, then that data is read immediately.
If the time-out period expires before a high priority symbology is read, the scanner will read any barcode in its view (low priority or unspecified). If there is no barcode in the scanner's view after the time-out period expires, then no data is reported.
Note: A low priority symbol must be centered on the aiming pattern to be read.
Scan a barcode below to enable or disable Preferred Symbology. Default = Preferred Symbology Off.
Preferred Symbology On
* Preferred Symbology Off
100
Granit XP User Guide
High Priority Symbology
To specify the high priority symbology, scan the High Priority Symbology barcode below. On the Symbology Charts on page 279, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 291, then Save. Default = None.
High Priority Symbology
Low Priority Symbology
To specify the low priority symbology, scan the Low Priority Symbology barcode below. On the Symbology Charts on page 279, find the symbology you want to set as low priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 291. If you want to set additional low priority symbologies, scan FF, then scan the 2 digit hex value from the Programming Chart, beginning on page 291, for the next symbology. You can program up to 5 low priority symbologies. Scan Save to save your selection. Default = None.
Low Priority Symbology
Preferred Symbology Time-out
Once you have enabled Preferred Symbology and entered the high and low priority symbologies, you must set the time-out period. This is the period of time the scanner will search for a high priority barcode after a low priority barcode has been encountered. Scan the barcode below, then set the delay (from 1-3,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 291, then Save. Default = 500 ms.
Preferred Symbology Time-out
Preferred Symbology Default
Scan the barcode below to set all Preferred Symbology entries to their default values.
Preferred Symbology Default
Granit XP User Guide
101
Output Sequence Overview
Output Sequence Editor
This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the barcodes are scanned. You can define up to 15 barcodes in an output sequence.
Note: To make Output Sequence Editor selections, you'll need to know the code I.D., code length, and character match(es) your application requires. Use the alphanumeric symbols from the Programming Chart, beginning on page 291. You must hold the trigger while reading each barcode in the sequence.
To Add an Output Sequence
An output sequence is created using a string of serial commands that is sent to the scanner. This string is most easily sent to the scanner using the EZConfig software tool (see EZConfig for Scanning Introduction on page 225). You can also accomplish this by scanning alphanumeric barcodes (see the Programming Chart, beginning on page 291).
1. If you are using barcodes to create your output sequence, scan Enter Output Sequence on page 106.
2. Code I.D. On the Symbology Charts on page 279, find the symbology to which you want to apply the output sequence format. Make a note of the hex value for that symbology. If you are using barcodes to create your output sequence, scan the 2 digit hex value from the Programming Chart, beginning on page 291.
3. Length Specify what length (up to 9999 characters) of data output will be acceptable for this symbology. Make a note of the length. If you are using barcodes to create your output sequence, scan the 4 digit data length Programming Chart, beginning on page 291. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.) When calculating the length, you must count any programmed prefixes, suffixes, or formatted characters as part of the length (unless using 9999).
4. Character Match Sequences On the ASCII Conversion Chart (Code Page 1252), page 282, find the hex value that represents the character(s) you want to match. Make a note of the hex value for the character(s). If you are using barcodes to create your output sequence, use the Programming Chart, beginning on page 291 to read the alphanumeric combination that represents the ASCII characters. (99 is the universal number, indicating all characters.)
102
Granit XP User Guide
5. End Output Sequence Editor Use FF to terminate this string or to begin another output sequence. If you are using barcodes, scan F F. Scan Save to save your entries.
Other Programming Selections
If you are creating an output sequence using barcodes, scan Discard (page 292) to exit without saving any output sequence changes.
Output Sequence Editor Commands
SEQBLK Sequence editor start command.
SEQPRE Add prefix to complete output sequences.
SEQSUF Add suffix to complete output sequences.
SEQSEP Add separators to complete output sequences.
SEQTTS1 Transmit partial sequence.
SEQSAT Define satisfactory subsets of full output sequence.
SEQTIM Timeout for sequence members when using SEQSAT.
SEQIPR Add prefix to partial output sequences.
SEQISU Add suffix to partial output sequences.
SEQISE Add separators to partial output sequences.
TRGSTO Timeout for partial output sequences.
FF
Termination string.
Examples outlining how to use these commands are shown below.
Output Sequence Example 1 - Three Symbologies
In this example, you are scanning PDF417, Code 128, and Code 39 barcodes, but you want the scanner to output Code 39 first, Code 128 second, and PDF417 third.
Set up the sequence editor with the following command line:
SEQBLK
sequence editor start command
Granit XP User Guide
103
62
code identifier for Code 39
9999
code length that must match for Code 39, 9999 = all lengths
43
start character match for Code 39, 43h = "C"
FF
termination string for first code
6A
code identifier for Code 128
9999
code length that must match for Code 128, 9999 = all lengths
54
start character match for Code 128, 54h = "T"
FF
termination string for first code
72
code identifier for PDF417
9999
code length that must match for PDF417, 9999 = all lengths
4D
start character match for PDF417, 4Dh = "M"
FF
termination string for third code
The whole command line would look like this:
SEQBLK62999943FF6A999954FF7299994DFF
The data is output as:
CODE39SMPLTSTMSGCODE128MSGPDF417
See the next example to further refine this output.
Output Sequence Example 2 - Three Symbologies with <> Separators
In this example, you are scanning the same three barcodes, but you want <> brackets and a carriage return and line feed to separate your output.
The sequence editor would use the same command line as shown in Output Sequence Example 1 - Three Symbologies (page 103):
SEQBLK
sequence editor start command
62
code identifier for Code 39
9999
code length that must match for Code 39, 9999 = all lengths
104
Granit XP User Guide
43
start character match for Code 39, 43h = "C"
FF
termination string for first code
6A
code identifier for Code 128
9999
code length that must match for Code 128, 9999 = all lengths
54
start character match for Code 128, 54h = "T"
FF
termination string for first code
72
code identifier for PDF417
9999
code length that must match for PDF417, 9999 = all lengths
4D
start character match for PDF417, 4Dh = "M"
FF
termination string for third code
But you would add your <> separators for each sequence:
SEQSEP99
separator for each sequence, 99 = all symbologies
3C
left bracket (<)
3E
right bracket (>)
And add the carriage return and line feed as a suffix:
SEQSUF99
separator for suffixes, 99 = all symbologies
0D
carriage return
0A
line feed
The whole command line would look like this:
SEQBLK62999943FF6A999954FF7299994DFFSEQSEP993C3ESEQSUF990D0 A
The data is output as:
<CODE39SMPL>
<TSTMSGCODE128>
<MSGPDF417>
Enter Output Sequence
If you are using barcodes to create your output sequence, scan Enter Output Sequence to begin scanning your string.
Granit XP User Guide
105
Enter Output Sequence
Partial Sequence
If an output sequence operation is terminated before all your output sequence criteria are met, the barcode data acquired to that point is a "partial sequence." You can define how partial sequences are output using the same types of command strings you used to create output sequences.
Partial Sequence Example - Three Symbologies with <> Separators, but with a Damaged Code
In this example, you are scanning PDF417, Code 128, and Code 39 barcodes, and you want the scanner to output Code 39 first, Code 128 second, and PDF417 third, in brackets, as shown below, but the Code 39 barcode has been damaged and cannot be output.
You would use the same command line as shown in Output Sequence Example 2 Three Symbologies with <> Separators (page 104):
SEQBLK
sequence editor start command
62
code identifier for Code 39
9999
code length that must match for Code 39, 9999 = all lengths
43
start character match for Code 39, 43h = "C"
FF
termination string for first code
6A
code identifier for Code 128
9999
code length that must match for Code 128, 9999 = all lengths
54
start character match for Code 128, 54h = "T"
FF
termination string for first code
72
code identifier for PDF417
106
Granit XP User Guide
9999
code length that must match for PDF417, 9999 = all lengths
4D
start character match for PDF417, 4Dh = "M"
FF
termination string for third code
SEQSEP99
separator for each sequence, 99 = all symbologies
3C
left bracket (<)
3E
right bracket (>)
SEQSUF99
separator for suffixes, 99 = all symbologies
0D
carriage return
0A
line feed
And you would add >PARTIAL< as the prefix to note the partial sequence:
SEQTTS1
transmit partial sequence
SEQISU99
add partial sequence prefix, 99 = all symbologies
3E
right bracket (>)
50
P
41
A
52
R
54
T
49
I
41
A
4C
L
3C
left bracket (<)
The whole command line would look like this:
SEQBLK62999943FF6A999954FF7299994DFFSEQSEP993C3ESEQSUF990D0 ASEQTTS1SEQISU993E5041525449414C3C
The data is output as:
>PARTIAL<
<TSTMSGCODE128>
<MSGPDF417>
Granit XP User Guide
107
Discard Partial Output Sequence
If you want to discard partial sequences when the output sequence operation is terminated before completion, scan Discard Partial Sequence.
* Discard Partial Sequence
Output Sequence Timeouts
You can set a timeout for every code in the output sequence defined by the SEQBLK command. The scanner applies the shortest timeout corresponding to any of the codes that have been read during the current trigger session. When the timeout expires, the scanner sends all codes that it has been read in the order they appear in the sequence defined by SEQBLK.
To specify the timeout, use the SEQTIM command followed by a list of timeouts in milliseconds. Each timeout is specified as a 4-decimal digit terminated by FF. The timeout value 9999 is special and indicates that the timeout for that code is "infinite".
The number of timeouts specified should correspond to the number of codes in the sequence defined by SEQBLK. You can specify one additional timeout, which will apply to codes not matching any member of the sequence. This can be useful if Require Output Sequence is On/Not Required. If you do not specify an additional timeout for codes not in the defined sequence, the last timeout specified by SEQTIM will apply.
Output Sequence Timeout Example
For example, if SEQBLK defines a 4-code sequence, you can specify timeouts of 5, 6, 7, and 8 seconds for codes 1-4 respectively using the command SEQTIM5000FF6000FF7000FF8000FF. Codes that are not part of the defined sequence would have an implied timeout of 8 seconds in this case (the final timeout in the list). To explicitly specify a timeout for such codes, you can include one more timeout at the end of the list. For example, to include a timeout of 1 second for non-sequence codes, use the command SEQTIM5000FF6000FF7000FF8000FF1000FF.
Satisfactory Subset of Full Sequence
You can define one or more subsets of barcodes from the complete sequence specified by SEQBLK. When you scan all the codes from one of these subsets, the scanner will transmit all the codes it has read in the sequence. The scanner sends the codes in the order defined by SEQBLK.
Note: To use the satisfactory subset feature, you must supply a timeout for each code in the sequence using SEQTIM.
108
Granit XP User Guide
Satisfactory Subset of Full Sequence Timeout Example
To specify a subset, list its members using the SEQSAT command and terminate each subset with FF. The members of each subset are specified as single hex digits corresponding to their index within the full sequence, 1 being the first. For example, to specify two subsets, the first consisting of the first and second code in the sequence and the second subset consisting of the second and third code, use the command SEQSAT12FF23FF.
To define a subset with an odd number of codes, insert a 0 before the final code index. For example, to define a 3-code subset consisting of the first, second, and third codes, use the command SEQSAT1203FF.
Default Output Sequence
Default Sequence programs the scanner to all universal values. Be certain you want to delete or clear all formats before you read the Default Sequence symbol.
Default Sequence
Require Output Sequence
When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. When it's On/Not Required, the scanner will attempt to get the output data to conform to an edited sequence but, if it cannot, the scanner transmits all output data to the host device as is, or formatted according to the partial sequence output format (see Partial Sequence on page 106).
When the output sequence is Off, the barcode data is output to the host as the scanner decodes it. Default = Off.
Note: This selection is unavailable when the Multiple Symbols Selection is turned on.
Required *Off
On/Not Required
Granit XP User Guide
109
Good Read Tone - Output Sequences
The scanner may be programmed to either beep or click in response to a good read of each barcode in an output sequence, or to emit a beep or error tone for a partial sequence. Default = Good Read Click - Each Code in Sequence and Error Tone - Partial Sequence Output.
,
Good Read Beep - Each Code in Sequence
Good Read Beep - Partial Sequence Output
* Good Read Click - Each Code in Sequence
* Error Tone - Partial Sequence Output
Multiple Symbols
When this programming selection is turned On, it allows you to read multiple symbols with a single pull of the scanner's trigger. If you press and hold the trigger, aiming the scanner at a series of symbols, it reads unique symbols once, beeping and or vibrating (if turned on) for each read. The scanner attempts to find and decode new symbols as long as the trigger is pulled. The maximum number of barcodes read is 21. When this programming selection is turned Off, the scanner will only read the symbol closest to the aiming beam. Default = Off.
On * Off
110
Granit XP User Guide
No Read
With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data Window (see page 225), an "NR" appears when a code cannot be read. If No Read is turned Off, the "NR" will not appear. Default = Off.
On
* Off
If you want a different notation than "NR," for example, "Error," or "Bad Code," you can edit the output message (see Data Format beginning on page 119). The hex code for the No Read symbol is 9C.
Video Reverse
Video Reverse is used to allow the scanner to read barcodes that are inverted. The Video Reverse Off barcode below is an example of this type of barcode. Scan Video Reverse Only to read only inverted barcodes. Scan Video Reverse and Standard Barcodes to read both types of codes. Default = Video Reverse Off. Note: After scanning Video Reverse Only, menu barcodes cannot be read. You must scan Video Reverse Off or Video Reverse and Standard Barcodes in order to read menu barcodes. Note: Images downloaded from the unit are not reversed. This is a setting for decoding only.
Video Reverse Only
Video Reverse and Standard Barcodes
Granit XP User Guide
111
* Video Reverse Off
Working Orientation
Some barcodes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner. Default = Upright.
Upright:
Upside Down:
Vertical, Top to Bottom: (Rotate CW 90°)
Vertical, Bottom to Top: (Rotate CCW 90°)
112
* Upright Upside Down
Vertical, Bottom to Top
Vertical, Top to Bottom
Granit XP User Guide
CHAPTER
5 DATA EDIT
Prefix/Suffix Overview
When a barcode is scanned, additional information is sent to the host computer along with the barcode data. This group of barcode data and additional, user-defined data is called a "message string." The selections in this section are used to build the user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and after scanned data. You can specify if they should be sent with all symbologies, or only with specific symbologies. The following illustration shows the breakdown of a message string:
Prefix
1-11 alpha numeric &
control characters
Scanned Data
variable length
Suffix
1-11 alpha numeric &
control characters
Points to Keep In Mind
· It is not necessary to build a message string. The selections in this chapter are only used if you wish to alter the default settings. Default prefix = None. Default suffix = None.
· A prefix or suffix may be added or cleared from one symbology or all symbologies.
· You can add any prefix or suffix from the ASCII Conversion Chart (Code Page 1252), beginning on page 282, plus Code I.D. and AIM I.D.
· You can string together several entries for several symbologies at one time.
· Enter prefixes and suffixes in the order in which you want them to appear on the output.
Granit XP User Guide
113
· When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character.
· The maximum size of a prefix or suffix configuration is 200 characters, which includes header information.
Add a Prefix or Suffix:
Step 1. Scan the Add Prefix or Add Suffix symbol (page 115).
Step 2. Step 3.
Determine the 2 digit hex value from the Symbology Charts (beginning on page 279) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is "j" and Hex ID is "6A".
Scan the 2 hex digits from the Programming Chart, beginning on page 291, or scan 9, 9 for all symbologies.
To add the Code I.D., scan 5, C, 8, 0. To add the AIM I.D., scan 5, C, 8, 1. To add the serial number, scan 5, C, 8, 8. To add a backslash (\), scan 5, C, 5, C.
Note: When adding a backslash (\), you must scan 5C twice once to create the leading backslash and then to create the backslash itself.
Step 4. Repeat Steps 2 and 3 for every prefix or suffix character. Step 5. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat the steps above to add a prefix or suffix for another symbology.
Example: Add a Tab Suffix to All Symbologies
Step 1. Step 2. Step 3.
Step 4.
Scan Add Suffix.
Scan 9, 9 from the Programming Chart, beginning on page 291 to apply this suffix to all symbologies.
Scan 0, 9 from the Programming Chart, beginning on page 291. This corresponds with the hex value for a horizontal tab, shown in the ASCII Conversion Chart (Code Page 1252), beginning on page 282.
Scan Save, or scan Discard to exit without saving.
Clear One or All Prefixes or Suffixes
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology. If you have been entering prefixes and suffixes for single symbologies, you can use Clear One Prefix (Suffix) to delete a specific character from a symbology. When you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are deleted.
114
Granit XP User Guide
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.
Step 2.
Determine the 2 digit hex value from the Symbology Chart (included in the Symbology Charts, beginning on page 279) for the symbology from which you want to clear the prefix or suffix.
Step 3. Scan the 2 digit hex value from the Programming Chart, beginning on page 291 or scan 9, 9 for all symbologies.
Your change is automatically saved.
Add a Carriage Return Suffix to All Symbologies
Scan the following barcode if you wish to add a carriage return suffix to all symbologies at once. This action first clears all current suffixes, then programs a carriage return suffix for all symbologies.
Prefix Selections
Add CR Suffix All Symbologies
Add Prefix
Clear All Prefixes
Suffix Selections
Clear One Prefix
Add Suffix
Clear One Suffix
Granit XP User Guide
115
Clear All Suffixes
Function Code Transmit
By default, all ASCII control characters are transmitted with barcode data. These non-printable characters are translated into predefined key strokes, or CTRL+X functions (see ASCII Conversion Chart (Code Page 1252), beginning on page 282). If these key strokes interfere with your host's software application, scan Disable to keep these ASCII control characters from being transmitted. Default = Enable.
* Enable
Disable
Note: You can also use a custom data format (see Data Format beginning on page 119) to translate these characters into a more meaningful output.
Intercharacter, Interfunction, and Intermessage Delays
Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage delays slow the transmission of data, increasing data integrity.
Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay barcode below, then scan the number of 5ms delays from the Programming Chart, beginning on page 291, then Save.
Prefix
Scanned Data Suffix
1234 5 Intercharacter Delay
116
Intercharacter Delay
Granit XP User Guide
To remove this delay, scan the Intercharacter Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 291.
Note: Intercharacter delays are not supported in USB serial emulation.
User Specified Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data. Scan the Delay Length barcode below, then scan the number of 5ms delays from the Programming Chart, beginning on page 291, then Save.
Next, scan the Character to Trigger Delay barcode, then the 2-digit hex value for a printable character to trigger the delay (see Lower ASCII Reference Table, page
283.)
Delay Length
Character to Trigger Delay
To remove this delay, scan the Delay Length barcode, and set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 291.
Interfunction Delay
An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each control character in the message string. Scan the Interfunction Delay barcode below, then scan the number of 5ms delays, and the Save barcode from the Programming Chart, beginning on page 291.
Prefix
Scanned Data Suffix
STX 1 HT 2 3 4 5 CR LF
Interfunction Delays
Interfunction Delay
Granit XP User Guide
117
To remove this delay, scan the Interfunction Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 291.
Intermessage Delay
An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission. Scan the Intermessage Delay barcode below, then scan the number of 5ms delays, and the Save barcode from the Programming Chart, beginning on page 291.
1st Scan Transmission 2nd Scan Transmission Intermessage Delay
Intermessage Delay
To remove this delay, scan the Intermessage Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 291.
118
Granit XP User Guide
CHAPTER
6 DATA FORMAT
Data Format Editor Introduction
You may use the Data Format Editor to change the scanner's output. For example, you can use the Data Format Editor to insert characters at certain points in barcode data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None.
Normally, when you scan a barcode, it is output automatically. However, when you create a format, you must use a "send" command (see Send Commands on page 122) within the format program to output data.
Multiple formats may be programmed into the scanner. They are stacked in the order in which they are entered. However, the following list presents the order in which formats are applied:
1. Specific Terminal ID, Actual Code ID, Actual Length
2. Specific Terminal ID, Actual Code ID, Universal Length
3. Specific Terminal ID, Universal Code ID, Actual Length
4. Specific Terminal ID, Universal Code ID, Universal Length
5. Universal Terminal ID, Actual Code ID, Actual Length
6. Universal Terminal ID, Actual Code ID, Universal Length
7. Universal Terminal ID, Universal Code ID, Actual Length
8. Universal Terminal ID, Universal Code ID, Universal Length
The maximum size of a data format configuration is 2000 bytes, which includes header information.
If a barcode is read that fails the first data format, the next data format, if there is one, will be used on the barcode data. If there is no other data format, the raw data is output.
Granit XP User Guide
119
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data Format code below.
* Default Data Format
Show Data Format
Scan the barcode below to show current data format settings.
Data Format Settings
Add a Data Format
Step 1. Step 2.
Step 3.
Scan the Enter Data Format symbol (page 121).
Select Primary/Alternate Format Determine if this will be your primary data format, or one of 3 alternate formats. This allows you to save a total of 4 different data formats. To program your primary format, scan 0 from the Programming Chart, beginning on page 291. If you are programming an alternate format, scan 1, 2, or 3, depending on which alternate format you are programming. (See Primary/Alternate Data Formats on page 137 for further information.)
Terminal Type Refer to Terminal ID Table (page 122) and locate the Terminal ID number for your PC. Scan three numeric barcodes from the Programming Chart, beginning on page 291, to program the scanner for your terminal ID (you must enter 3 digits). For example, scan 0 0 3 for an AT wedge.
Note: 099 indicates all terminal types.
Step 4.
Code I.D. In the Symbology Charts, beginning on page 279, find the symbology to which you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 291.
If you wish to create a data format for all symbologies, with the exception of some specific symbologies, refer to B8 (page 135).
If you are creating a data format for Batch Mode Quantity, use 35 for the Code I.D.
Note: 99 indicates all symbologies.
Step 5.
Length Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length from the Programming
120
Granit XP User Guide
Chart, beginning on page 291. For example, 50 characters is entered as 0050.
Note: 9999 indicates all lengths.
Step 6.
Editor Commands Refer to Data Format Editor Commands (page 122). Scan the symbols that represent the command you want to enter.
Step 7. Scan Save to save your data format, or Discard to exit without saving your changes.
Enter Data Format
Save
Discard
Other Programming Selections
· Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart, beginning on page 291. If you are clearing an alternate format, scan 1, 2, or 3, depending on the format you are clearing. Scan the Terminal Type and Code I.D. (see Symbology Charts on page 279), and the barcode data length for the specific data format that you want to delete. All other formats remain unaffected.
· Clear all Data Formats This clears all data formats.
· Save Exit and save your data format changes.
· Discard Exit without saving any data format changes.
Clear One Data Format
Clear All Data Formats
Granit XP User Guide
121
Save
Discard
Terminal ID Table
Terminal USB
Serial Keyboard
Model(s) PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop RS232 TTL RS232 True RS485 (IBM-HHBCR 1+2, 46xx) PS2 compatibles AT compatibles
Terminal ID 124 125 134 130 131 128 129 000 000 051 003 002
Data Format Editor Commands
When working with the Data Format Editor, a virtual cursor is moved along your input data string. The following commands are used to both move this cursor to different positions, and to select, replace, and insert data into the final output.
Send Commands
Send all characters
F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character. Syntax = F1xx where xx stands for the insert character's hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
122
Granit XP User Guide
Send a number of characters
F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor position and continue for "nn" characters or through the last character in the input message, followed by character "xx." Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the insert character's hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
F2 Example: Send a number of characters
Send the first 10 characters from the barcode above, followed by a carriage return. Command string: F2100D F2 is the "Send a number of characters" command 10 is the number of characters to send 0D is the hex value for a CR The data is output as: 1234567890
F2 and F1 Example: Split characters into 2 lines Send the first 10 characters from the barcode above, followed by a carriage return, followed by the rest of the characters. Command string: F2100DF10D F2 is the "Send a number of characters" command 10 is the number of characters to send for the first line 0D is the hex value for a CR F1 is the "Send all characters" command 0D is the hex value for a CR The data is output as: 1234567890 ABCDEFGHIJ <CR>
Granit XP User Guide
123
Send all characters up to a particular character
F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character "ss," followed by an insert character. The cursor is moved forward to the "ss" character. Syntax = F3ssxx where ss stands for the search character's hex value for its ASCII code, and xx stands for the insert character's hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
F3 Example: Send all characters up to a particular character
Using the barcode above, send all characters up to but not including "D," followed by a carriage return.
Command string: F3440D
F3 is the "Send all characters up to a particular character" command
44 is the hex value for a 'D"
0D is the hex value for a CR
The data is output as: 1234567890ABC <CR>
Send all characters up to a string
B9 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search string "s...s." The cursor is moved forward to the beginning of the "s...s" string. Syntax = B9nnnns...s where nnnn stands for the length of the string, and s...s stands for the string to be matched. The string is made up of hex values for the characters in the string. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
B9 Example: Send all characters up to a defined string
Using the barcode above, send all characters up to but not including "AB." Command string: B900024142 B9 is the "Send all characters up to a string" command 0002 is the length of the string (2 characters) 41 is the hex value for A
124
Granit XP User Guide
42 is the hex value for B The data is output as: 1234567890
Send all but the last characters
E9 Include in the output message all but the last "nn" characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included. Syntax = E9nn where nn stands for the numeric value (00-99) for the number of characters that will not be sent at the end of the message.
Insert a character multiple times
F4 Send "xx" character "nn" times in the output message, leaving the cursor in the current position. Syntax = F4xxnn where xx stands for the insert character's hex value for its ASCII code, and nn is the numeric value (00-99) for the number of times it should be sent. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes. E9 and F4 Example: Send all but the last characters, followed by 2 tabs
Send all characters except for the last 8 from the barcode above, followed by 2 tabs. Command string: E908F40902 E9 is the "Send all but the last characters" command 08 is the number of characters at the end to ignore F4 is the "Insert a character multiple times" command 09 is the hex value for a horizontal tab 02 is the number of times the tab character is sent The data is output as: 1234567890AB <tab><tab>
Insert a string
BA Send "ss" string of "nn" length in the output message, leaving the cursor in the current position. Syntax = BAnnnns...s where nnnn stands for the length of the string, and s...s stands for the string. The string is made up of hex values for the characters in the string. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Granit XP User Guide
125
B9 and BA Example: Look for the string "AB" and insert 2 asterisks (**)
Using the barcode above, send all characters up to but not including "AB." Insert 2 asterisks at that point, and send the rest of the data with a carriage return after. Command string: B900024142BA00022A2AF10D B9 is the "Send all characters up to a string" command 0002 is the length of the string (2 characters) 41 is the hex value for A 42 is the hex value for B BA is the "Insert a string" command 0002 is the length of the string to be added (2 characters) 2A is the hex value for an asterisk (*) 2A is the hex value for an asterisk (*) F1 is the "Send all characters" command 0D is the hex value for a CR The data is output as: 1234567890**ABCDEFGHIJ <CR>
Insert symbology name
B3 Insert the name of the barcode symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page 279). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Insert barcode length
B4 Insert the barcode length in the output message, without moving the cursor. The length is expressed as a numeric string and does not include leading zeros. B3 and B4 Example: Insert the symbology name and length
Send the symbology name and length before the barcode data from the barcode above. Break up these insertions with spaces. End with a carriage return.
Command string: B3F42001B4F42001F10D
126
Granit XP User Guide
B3 is the "Insert symbology name" command F4 is the "Insert a character multiple times" command 20 is the hex value for a space 01 is the number of times the space character is sent B4 is the "Insert barcode length" command F4 is the "Insert a character multiple times" command 20 is the hex value for a space 01 is the number of times the space character is sent F1 is the "Send all characters" command 0D is the hex value for a CR The data is output as: Code128 20 1234567890ABCDEFGHIJ <CR>
Insert key strokes
B5 Insert a key stroke or combination of key strokes. Key strokes are dependent on your keyboard (see Keyboard Key References on page 288). Any key can be inserted, including arrows and functions. Syntax = 5CB5xxssnn where xx is the number of keys pressed (without key modifiers), ss is the key modifier from the table below, and nn is the key number from the Keyboard Key References, page 288.
Key Modifiers No Key Modifier Shift Left Shift Right Alt Left Alt Right Control Left Control Right
Hex 00 01 02 04 08 10 20
For example, B501021F inserts an "A" on a 104 key, U.S. style keyboard. B5 = the command, 01 = number of key press events (without the key modifier), 02 is the key modifier for Shift Right, and 1F is the "a" key. If a lower case "a" were to be inserted, B501001F would be entered.
If there are three keystrokes, the syntax would change from B5xxssnn for one keystroke to B5xxssnnssnnssnn. An example that would insert "abc" is as follows: B503001F00320030F833.
Note: Key modifiers can be added together when needed. The sum is converted to hexadecimals.
Example: Control Left+Shift Left = 17, converted to hexadecimal = 11.
Granit XP User Guide
127
Move Commands
Move the cursor forward a number of characters
F5 Move the cursor ahead "nn" characters from current cursor position. Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead. F5 Example: Move the cursor forward and send the data
Move the cursor forward 3 characters, then send the rest of the barcode data from the barcode above. End with a carriage return. Command string: F503F10D F5 is the "Move the cursor forward a number of characters" command 03 is the number of characters to move the cursor F1 is the "Send all characters" command 0D is the hex value for a CR The data is output as: 4567890ABCDEFGHIJ <CR>
Move the cursor backward a number of characters
F6 Move the cursor back "nn" characters from current cursor position. Syntax = F6nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved back.
Move the cursor to the beginning
F7 Move the cursor to the first character in the input message. Syntax = F7. FE and F7 Example: Manipulate barcodes that begin with a 1
Search for barcodes that begin with a 1. If a barcode matches, move the cursor back to the beginning of the data and send 6 characters followed by a carriage return. Using the barcode above:
Command string: FE31F7F2060D
FE is the "Compare characters" command
31 is the hex value for 1
128
Granit XP User Guide
F7 is the "Move the cursor to the beginning" command F2 is the "Send a number of characters" command 06 is the number of characters to send 0D is the hex value for a CR The data is output as: 123456 <CR>
Move the cursor to the end
EA Move the cursor to the last character in the input message. Syntax = EA.
Search Commands
Search forward for a character
F8 Search the input message forward for "xx" character from the current cursor position, leaving the cursor pointing to the "xx" character. Syntax = F8xx where xx stands for the search character's hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes. F8 Example: Send barcode data that starts after a particular character
Search for the letter "D" in barcodes and send all the data that follows, including the "D." Using the barcode above: Command string: F844F10D F8 is the "Search forward for a character" command 44 is the hex value for "D" F1 is the "Send all characters" command 0D is the hex value for a CR The data is output as: DEFGHIJ <CR>
Granit XP User Guide
129
Search backward for a character
F9 Search the input message backward for "xx" character from the current cursor position, leaving the cursor pointing to the "xx" character. Syntax = F9xx where xx stands for the search character's hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Search forward for a string
B0 Search forward for "s" string from the current cursor position, leaving cursor pointing to "s" string. Syntax = B0nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B0000454657374 will search forward for the first occurrence of the 4 character string "Test." Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes. B0 Example: Send barcode data that starts after a string of characters
Search for the letters "FGH" in barcodes and send all the data that follows, including "FGH." Using the barcode above: Command string: B00003464748F10D B0 is the "Search forward for a string" command 0003 is the string length (3 characters) 46 is the hex value for "F" 47 is the hex value for "G" 48 is the hex value for "H" F1 is the "Send all characters" command 0D is the hex value for a CR The data is output as: FGHIJ <CR>
130
Granit XP User Guide
Search backward for a string
B1 Search backward for "s" string from the current cursor position, leaving cursor pointing to "s" string. Syntax = B1nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B1000454657374 will search backward for the first occurrence of the 4 character string "Test." Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Search forward for a non-matching character
E6 Search the input message forward for the first non-"xx" character from the current cursor position, leaving the cursor pointing to the non-"xx" character. Syntax = E6xx where xx stands for the search character's hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
E6 Example: Remove zeros at the beginning of barcode data
This example shows a barcode that has been zero filled. You may want to ignore the zeros and send all the data that follows. E6 searches forward for the first character that is not zero, then sends all the data after, followed by a carriage return. Using the barcode above:
Command string: E630F10D
E6 is the "Search forward for a non-matching character" command
30 is the hex value for 0
F1 is the "Send all characters" command
0D is the hex value for a CR
The data is output as: 37692 <CR>
Search backward for a non-matching character
E7 Search the input message backward for the first non-"xx" character from the current cursor position, leaving the cursor pointing to the non-"xx" character. Syntax = E7xx where xx stands for the search character's hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Granit XP User Guide
131
Miscellaneous Commands
Suppress characters
FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command. Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed characters in the list, and xxyy .. zz is the list of characters to be suppressed. FB Example: Remove spaces in barcode data
This example shows a barcode that has spaces in the data. You may want to remove the spaces before sending the data. Using the barcode above: Command string: FB0120F10D FB is the "Suppress characters" command 01 is the number of character types to be suppressed 20 is the hex value for a space F1 is the "Send all characters" command 0D is the hex value for a CR The data is output as: 34567890 <CR>
Stop suppressing characters
FC Disables suppress filter and clear all suppressed characters. Syntax = FC.
Replace characters
E4 Replaces up to 15 characters in the output message, without moving the cursor. Replacement continues until the E5 command is encountered. Syntax = E4nnxx1xx2yy1yy2...zz1zz2 where nn is the total count of the number of characters in the list (characters to be replaced plus replacement characters); xx1 defines characters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2. E4 Example: Replace zeros with CRs in barcode data
132
Granit XP User Guide
If the barcode has characters that the host application does not want included, you can use the E4 command to replace those characters with something else. In this example, you will replace the zeros in the barcode above with carriage returns.
Command string: E402300DF10D
E4 is the "Replace characters" command
02 is the total count of characters to be replaced, plus the replacement characters (0 is replaced by CR, so total characters = 2)
30 is the hex value for 0
0D is the hex value for a CR (the character that will replace the 0)
F1 is the "Send all characters" command
0D is the hex value for a CR
The data is output as: 1234 5678 ABC <CR>
Stop replacing characters
E5 Terminates character replacement. Syntax = E5.
Compare characters
FE Compare the character in the current cursor position to the character "xx." If characters are equal, move the cursor forward one position. Syntax = FExx where xx stands for the comparison character's hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Compare string
B2 Compare the string in the input message to the string "s." If the strings are equal, move the cursor forward past the end of the string. Syntax = B2nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B2000454657374 will compare the string at the current cursor position with the 4 character string "Test." Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 282 for decimal, hex and character codes.
Check for a number
EC Check to make sure there is an ASCII number at the current cursor position. The format is aborted if the character is not numeric.
Granit XP User Guide
133
EC Example: Only output the data if the barcode begins with a number If you want only data from barcodes that begin with a number, you can use EC to check for the number. Command string: ECF10D EC is the "Check for a number" command F1 is the "Send all characters" command 0D is the hex value for a CR
If this barcode is read,
the next data format, if there is one, will
be used on the data. If there is no other format, the format fails and the raw data is output as AB1234.
If this barcode is read:
the data is output as:
1234AB <CR>
Check for non-numeric character
ED Check to make sure there is a non-numeric ASCII character at the current cursor position. The format is aborted if the character is numeric. ED Example: Only output the data if the barcode begins with a letter If you want only data from barcodes that begin with a letter, you can use ED to check for the letter. Command string: EDF10D ED is the "Check for a non-numeric character" command F1 is the "Send all characters" command 0D is the hex value for a CR
If this barcode is read,
the next data format, if there is one, will be
used on this data. If there is no other format, the format fails and the raw data is output as 1234AB.
If this barcode is read:
AB1234 <CR>
the data is output as:
134
Granit XP User Guide
Insert a delay
EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation.
Discard Data
B8 Discards types of data. For example, you may want to discard Code 128 barcodes that begin with the letter A. In step 4 (page 120), select 6A (for Code 128), and in step 5, select 9999 (for all lengths). Enter FE41B8 to compare and discard Code 128 barcodes that begin with the letter A. Syntax = B8.
Note: The B8 command must be entered after all other commands. The Data Format must be Required (see page 135) in order for the B8 command to work. If Data Format is On, but Not Required (page 136), barcode data that meets the B8 format is scanned and output as usual. Because the data format needs to be On and Required (page 136) for the B8 command, you must input data formats for all barcodes you wish to discard as well as all barcodes you wish to output. Other data format settings impact the B8 command. If Data Format Non-Match Error Tone is On (page 136), the scanner emits an error tone. If Data format Non-Match Error Tone is Off, the code is disabled for reading and no tone is sounded.
Data Formatter
When Data Formatter is turned Off, the barcode data is output to the host as read, including prefixes and suffixes.
Data Formatter Off
You may wish to require the data to conform to a data format you have created and saved. The following settings can be applied to your data format:
· Data Formatter On, Not Required, Keep Prefix/Suffix Scanned data is modified according to your data format, and prefixes and suffixes are transmitted.
· Data Formatter On, Not Required, Drop Prefix/Suffix Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted. If a data format is not found for that symbol, the prefixes and suffixes are transmitted.
· Data Format Required, Keep Prefix/Suffix Scanned data is modified according to your data format, and prefixes and suffixes are transmitted. Any data that does not match your data format
Granit XP User Guide
135
requirements generates an error tone and the data in that barcode is not transmitted. If you wish to process this type of barcode without generating an error tone, see Data Format Non-Match Error Tone. · Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted. Any data that does not match your data format requirements generates an error tone. If you wish to process this type of barcode without generating an error tone, see Data Format Non-Match Error Tone. Choose one of the following options. Default = Data Formatter On, Not Required, Keep Prefix/Suffix.
* Data Formatter On, Not Required,
Keep Prefix/Suffix
Data Formatter On, Not Required,
Drop Prefix/Suffix
Data Format Required, Keep Prefix/Suffix
Data Format Required, Drop Prefix/Suffix
Data Format Non-Match Error Tone
When a barcode is encountered that doesn't match your required data format, the scanner normally generates an error tone. However, you may want to continue scanning barcodes without hearing the error tone. If you scan the Data Format Non-Match Error Tone Off barcode, data that doesn't conform to your data format is not transmitted, and no error tone will sound. If you wish to hear the error tone when a non-matching barcode is found, scan the Data Format Non-Match Error Tone On barcode. Default = Data Format Non-Match Error Tone On.
* Data Format Non-Match Error Tone On
136
Granit XP User Guide
Data Format Non-Match Error Tone Off
Primary/Alternate Data Formats
You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the barcodes below.
Primary Data Format
Data Format 1
Data Format 2
Data Format 3
Single Scan Data Format Change
You can also switch between data formats for a single scan. The next barcode is scanned using an alternate data format, then reverts to the format you have selected above (either Primary, 1, 2, or 3). For example, you may have set your device to the data format you saved as Data Format 3. You can switch to Data Format 1 for a single trigger pull by scanning the Single Scan-Data Format 1 barcode below. The next barcode that is scanned uses Data Format 1, then reverts back to Data Format 3.
Single Scan-Primary Data Format
Granit XP User Guide
137
Single Scan-Data Format 2
Single Scan-Data Format 1 Single Scan-Data Format 3
138
Granit XP User Guide
CHAPTER
7 SYMBOLOGIES
This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults.
· All Symbologies · Aztec Code · China Post (Hong Kong 2 of 5) · Chinese Sensible (Han Xin) Code · Codabar · Codablock A · Codablock F · Code 11 · Code 128 · Code 32 Pharmaceutical (PARAF) · Code 39 · Code 93
· Data Matrix
· Digimarc BarcodeTM · DotCode · EAN/JAN-13 · EAN/JAN-8 · GS1 Composite Codes · GS1 DataBar Expanded
· GS1 DataBar Limited
· GS1 DataBar Omnidirectional · GS1 Emulation · GS1-128
· Interleaved 2 of 5 · Korea Post · Label Code · Matrix 2 of 5 · MaxiCode · MicroPDF417 · MSI · NEC 2 of 5 · Postal Codes - 2D · Postal Codes - Linear · PDF417 · QR Code · Straight 2 of 5 IATA (two-bar start/
stop)
· Straight 2 of 5 Industrial (three-bar start/stop)
· TCIF Linked Code 39 (TLC39) · Telepen · Trioptic Code · UPC-A · UPC-A/EAN-13 with Extended
Coupon Code · UPC-E0 · UPC-E1
Granit XP User Guide
139
All Symbologies
For best scanner performance, you should only enable the symbologies that you need. Scan All Symbologies Off to disable all symbologies, then enable the symbologies you need by scanning the On barcode for each symbology.
All Symbologies Off
Message Length Description
You are able to set the valid reading length of some of the barcode symbologies. You may wish to set the same value for minimum and maximum length to force the scanner to read fixed length barcode data. This helps reduce the chances of a misread.
Example: Decode only those barcodes with a count of 9-20 characters. Min. length = 09 Max. length = 20
Example: Decode only those barcodes with a count of 15 characters. Min. length = 15 Max. length = 15
For a value other than the minimum and maximum message length defaults, scan the barcodes included in the explanation of the symbology, then scan the digit value of the message length and Save barcodes from the Programming Chart, beginning on page 291. The minimum and maximum lengths and the defaults are included with the respective symbologies.
Codabar
<Default All Codabar Settings>
Codabar On/Off
* On
140
Granit XP User Guide
Off
Codabar Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not transmit Start/Stop characters. Default = Don't Transmit.
Transmit
* Don't Transmit
Codabar Check Character
Codabar check characters are created using different "modulos." You can program the scanner to read only Codabar barcodes with Modulo 16 check characters. Default = No Check Character. No Check Character indicates that the scanner reads and transmits barcode data with or without a check character. When Check Character is set to Validate and Transmit, the scanner will only read Codabar barcodes printed with a check character, and will transmit this character at the end of the scanned data. When Check Character is set to Validate, but Don't Transmit, the unit will only read Codabar barcodes printed with a check character, but will not transmit the check character with the scanned data.
* No Check Character
Validate Modulo 16 and Transmit
Validate Modulo 16, but Don't Transmit
Granit XP User Guide
141
Codabar Concatenation
Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a "D" start character, adjacent to a symbol having a "D" stop character. In this case the two messages are concatenated into one with the "D" characters omitted.
A1 2 3 4D D5 6 7 8A
Select Require to prevent the scanner from decoding a single "D" Codabar symbol without its companion. This selection has no effect on Codabar symbols without Stop/Start D characters. Default = Off.
On
* Off
Require
Codabar Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60.
Minimum Message Length
Maximum Message Length
142
Granit XP User Guide
Code 39
< Default All Code 39 Settings >
Code 39 On/Off
* On
Off
If you are reading Code 39 barcodes, Codablock A should remain disabled. If you are enabling Codablock A (see Codablock A on page 179), you should disable Code 39.
Code 39 Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not transmit Start/Stop characters. Default = Don't Transmit.
Transmit
* Don't Transmit
Code 39 Check Character
No Check Character indicates that the scanner reads and transmits barcode data with or without a check character. When Check Character is set to Validate, but Don't Transmit, the unit only reads Code 39 barcodes printed with a check character, but will not transmit the check character with the scanned data.
Granit XP User Guide
143
When Check Character is set to Validate and Transmit, the scanner only reads Code 39 barcodes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character.
* No Check Character
Validate, but Don't Transmit
Validate and Transmit
Code 39 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 0-48. Minimum Default = 0, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Code 39 Append
This function allows the scanner to append the data from several Code 39 barcodes together before transmitting them to the host computer. When the scanner encounters a Code 39 barcode with the append trigger character(s), it buffers Code 39 barcodes until it reads a Code 39 barcode that does not have the append trigger. The data is then transmitted in the order in which the barcodes were read (FIFO). Default = Off.
On
* Off
144
Granit XP User Guide
Code 32 Pharmaceutical (PARAF)
Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as PARAF. Default = Off.
Note: Trioptic Code (page 179) must be turned off while scanning Code 32 Pharmaceutical codes.
On
* Off
Full ASCII
If Full ASCII Code 39 decoding is enabled, certain character pairs within the barcode symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.
Full ASCII Table
NUL %U DLE $P
SOH $A
DC1 $Q
STX $B
DC2 $R
ETX $C
DC3 $S
EOT $D
DC4 $T
ENQ $E
NAK $U
ACK $F
SYN $V
BEL $G
ETB $W
BS $H
CAN $X
HT $I
EM $Y
LF $J
SUB $Z
VT $K
ESC %A
FF $L
FS %B
CR $M
GS %C
SO $N
RS %D
SI $O
US %E
SP SPACE 0
! /A
1
" /B
2
# /C
3
$ /D
4
% /E
5
& /F
6
` /G
7
( /H
8
) /I
9
* /J
:
+ /K
;
, /L
<
--
=
..
>
/ /O
?
0
@ %V
1
AA
2
BB
3
CC
4
DD
5
EE
6
FF
7
GG
8
HH
9
II
/Z J J
%F K K
%G L L
%H M M
%I N N
%J O O
PP
` %W p +P
Q Q a +A q +Q
RR
b +B r +R
SS
c +C s +S
TT
d +D t +T
U U e +E u +U
VV
f +F v +V
W W g +G w +W
XX
h +H x +X
YY
i +I
y +Y
ZZ
j +J z +Z
[ %K k +K { %P
\ %L l +L | %Q
] %M m +M } %R
^ %N n +N ~ %S
_ %O o +O DEL %T
Character pairs /M and /N decode as a minus sign and period respectively. Character pairs /P through /Y decode as 0 through 9.
Full ASCII On
Granit XP User Guide
145
* Full ASCII Off
Code 39 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the barcode below, select the code page with which the barcodes were created (see ISO 2022/ISO 646 Character Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly.
Interleaved 2 of 5
Code 39 Code Page
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5 On/Off
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits barcode data with or without a check digit. When Check Digit is set to Validate, but Don't Transmit, the unit only reads Interleaved 2 of 5 barcodes printed with a check digit, but will not transmit the check digit with the scanned data.
146
Granit XP User Guide
When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 barcodes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate, but Don't Transmit
Validate and Transmit
Interleaved 2 of 5 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 6, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
FEBRABAN Decode
Scan the barcodes below to turn FEBRABAN Boleto decoding on or off. Default = Off.
FEBRABAN Decode On
*FEBRABAN Decode Off
Granit XP User Guide
147
NEC 2 of 5
< Default All NEC 2 of 5 Settings >
NEC 2 of 5 On/Off
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits barcode data with or without a check digit. When Check Digit is set to Validate, but Don't Transmit, the unit only reads NEC 2 of 5 barcodes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit, the scanner only reads NEC 2 of 5 barcodes printed with a check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate, but Don't Transmit
Validate and Transmit
148
Granit XP User Guide
NEC 2 of 5 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Code 93
Maximum Message Length
< Default All Code 93 Settings >
Code 93 On/Off
* On
Off
Code 93 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Granit XP User Guide
149
Code 93 Append
This function allows the scanner to append the data from several Code 93 barcodes together before transmitting them to the host computer. When this function is enabled, the scanner stores those Code 93 barcodes that start with a space (excluding the start and stop symbols), and does not immediately transmit the data. The scanner stores the data in the order in which the barcodes are read, deleting the first space from each. The scanner transmits the appended data when it reads a Code 93 barcode that starts with a character other than a space. Default = Off.
On
* Off
Code 93 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the barcode below, select the code page with which the barcodes were created (see ISO 2022/ISO 646 Character Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly.
Code 93 Code Page
150
Granit XP User Guide
Straight 2 of 5 Industrial (three-bar start/stop)
<Default All Straight 2 of 5 Industrial Settings>
Straight 2 of 5 Industrial On/Off
On
* Off
Straight 2 of 5 Industrial Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Granit XP User Guide
151
Straight 2 of 5 IATA (two-bar start/stop)
<Default All Straight 2 of 5 IATA Settings>
Straight 2 of 5 IATA On/Off
On
* Off
Straight 2 of 5 IATA Redundancy
If you are encountering errors when reading Straight 2 of 5 IATA barcodes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a barcode is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the barcode. To adjust the redundancy, scan the Straight 2 of 5 IATA Redundancy barcode below, then scan a redundancy count between 0 and 10 on the Programming Chart, beginning on page 291. Then scan the Save barcode. Default = 0.
Straight 2 of 5 IATA Redundancy
Straight 2 of 5 IATA Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
152
Maximum Message Length
Granit XP User Guide
Matrix 2 of 5
<Default All Matrix 2 of 5 Settings>
Matrix 2 of 5 On/Off
On
* Off
Matrix 2 of 5 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Granit XP User Guide
153
Code 11
<Default All Code 11 Settings>
Code 11 On/Off
On
* Off
Check Digits Required
This option sets whether 1 or 2 check digits are required with Code 11 barcodes. Default = Two Check Digits.
One Check Digit
* Two Check Digits
Code 11 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
154
Granit XP User Guide
Code 128
<Default All Code 128 Settings>
Code 128 On/Off
* On
Off
If you are reading Code 128 barcodes, Codablock F should remain disabled. If you are enabling Codablock F (see Codablock F on page 180), you should disable Code 128.
ISBT 128 Concatenation
In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner. The use of ISBT formats requires a paid license. The ISBT 128 Application Specification describes 1) the critical data elements for labeling blood products, 2) the current recommendation to use Code 128 due to its high degree of security and its space-efficient design, 3) a variation of Code 128 that supports concatenation of neighboring symbols, and 4) the standard layout for barcodes on a blood product label. Use the barcodes below to turn concatenation on or off. Default =Off.
On
* Off
Code 128 Redundancy
If you are encountering errors when reading Code 128 barcodes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a barcode is decoded before transmission, which may reduce the number of errors. Note that
Granit XP User Guide
155
the higher the redundancy count, the longer it will take to decode the barcode. To adjust the redundancy, scan the Code 128 Redundancy barcode below, then scan a redundancy count between 0 and 10 on the Programming Chart, beginning on page 291. Then scan the Save barcode. Default = 0.
Code 128 Redundancy
Code 128 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Code 128 Append
This function allows the scanner to append the data from several Code 128 barcodes together before transmitting them to the host computer. When the scanner encounters a Code 128 barcode with the append trigger character(s), it buffers Code 128 barcodes until it reads a Code 128 barcode that does not have the append trigger. The data is then transmitted in the order in which the barcodes were read (FIFO). Default = Off.
On
* Off
Code 128 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the barcode below, select the code page with which the barcodes were created (see ISO 2022/ISO 646 Character
156
Granit XP User Guide
Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly.
GS1-128
Code 128 Code Page
<Default All GS1-128 Settings>
GS1-128 On/Off
* On
Off
GS1-128 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Granit XP User Guide
157
Telepen
<Default All Telepen Settings>
Telepen On/Off
On
* Off
Telepen Output
Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII (start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output.
* AIM Telepen Output
Original Telepen Output
Telepen Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60.
Minimum Message Length
158
Granit XP User Guide
UPC-A
Maximum Message Length
<Default All UPC-A Settings>
UPC-A On/Off
* On
Off
Note: To convert UPC-A barcodes to EAN-13, see Convert UPC-A to EAN-13 on page 166.
UPC-A Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
* On
Off
Granit XP User Guide
159
UPC-A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but can be programmed so it is not transmitted (Off). Default = On.
* On
Off
UPC-A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
UPC-A Addenda Required
When Required is scanned, the scanner will only read UPC-A barcodes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 160. Default = Not Required.
Required
160
Granit XP User Guide
* Not Required
Addenda Timeout
You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A Addenda Required. Set the length (in milliseconds) for this timeout by scanning the barcode below, then setting the timeout (from 0-500 milliseconds) by scanning digits from the Programming Chart, beginning on page 291 of this manual, then Save. Default = 120. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches.
Addenda Timeout
UPC-A Addenda Separator
When this feature is On, there is a space between the data from the barcode and the data from the addenda. When turned Off, there is no space. Default = On.
* On
Off
UPC-A/EAN-13 with Extended Coupon Code
Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single barcodes. If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single scan, it transmits both as one symbologies. Otherwise, it transmits the first coupon code it reads.
Granit XP User Guide
161
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a single read to transmit the data. No data is output unless both codes are read. Default = Off.
* Off
Allow Concatenation
Require Concatenation
Addenda Timeout
You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A/EAN-13 with Extended Coupon Code. Set the length (in milliseconds) for this timeout by scanning the barcode below, then setting the timeout (from 0-500 milliseconds) by scanning digits from the Programming Chart, beginning on page 291 of this manual, then Save. Default = 120. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches.
Addenda Timeout
Coupon GS1 DataBar Output
If you scan coupons that have both UPC and GS1 Databar codes, you may wish to scan and output only the data from the GS1 Databar code. Scan the GS1 Output On code below to scan and output only the GS1 Databar code data. Default = GS1 Output Off.
* GS1 Output Off
GS1 Output On
162
Granit XP User Guide
UPC-E0
<Default All UPC-E Settings>
UPC-E0 On/Off
Most U.P.C. barcodes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to read codes that lead with the 1 number system, use UPC-E1 (page 165). Default = On.
* UPC-E0 On
UPC-E0 Off
UPC-E0 Expand
UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off.
On
* Off
UPC-E0 Addenda Required
When Required is scanned, the scanner will only read UPC-E barcodes that have addenda. Default = Not Required.
Required
Granit XP User Guide
* Not Required
163
Addenda Timeout
You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-E0 Addenda Required. Set the length (in milliseconds) for this timeout by scanning the barcode below, then setting the timeout (from 0-500 milliseconds) by scanning digits from the Programming Chart, beginning on page 291 of this manual, then Save. Default = 120. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches.
Addenda Timeout
UPC-E0 Addenda Separator
When this feature is On, there is a space between the data from the barcode and the data from the addenda. When turned Off, there is no space. Default = On.
* On
Off
UPC-E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
* On
Off
164
Granit XP User Guide
UPC-E0 Leading Zero
This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = On.
* On
Off
UPC-E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
UPC-E1
Most U.P.C. barcodes lead with the 0 number system. For these codes, use UPC-E0 (page 163). If you need to read codes that lead with the 1 number system, use the UPC-E1 On selection. Default = Off.
UPC-E1 On
Granit XP User Guide
165
EAN/JAN-13
* UPC-E1 Off
<Default All EAN/JAN Settings>
EAN/JAN-13 On/Off
* On
Off
Convert UPC-A to EAN-13
When UPC-A Converted to EAN-13 is selected, UPC-A barcodes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A. Default = Do no Convert UPC-A.
UPC-A Converted to EAN-13
* Do not Convert UPC-A
166
Granit XP User Guide
EAN/JAN-13 Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
* On
Off
EAN/JAN-13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN-13 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-13 barcodes that have addenda. Default = Not Required.
Required
* Not Required
Granit XP User Guide
167
EAN-13 Beginning with 290 Addenda Required
This setting programs the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with "290." The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 barcodes that begin with "290" must have a 5 digit addendum. The EAN-13 barcode with the 5 digit addendum is then transmitted as a single, concatenated barcode. If a 5 digit addendum is not found within the Addenda Timeout period, the EAN-13 barcode is discarded.
Note: If you are using EAN-13 Beginning with 290 Addenda Required (page 168), this setting will take precedence. Don't Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don't Require 5 Digit Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don't Require 5 Digit Addenda.
* Don't Require 5 Digit Addenda
Require 5 Digit Addenda
EAN-13 Beginning with 378/379 Addenda Required
This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a "378" or "379." The following settings can be programmed: Require Addenda: All EAN-13 barcodes that begin with a "378" or "379" must have a 2 digit addenda, a 5 digit addenda, or a combination of these addenda. The EAN13 barcode with the addenda is then transmitted as a single, concatenated barcode. If the required addenda is not found within the Addenda Timeout period, the EAN-13 barcode is discarded. Don't Require Addenda: If you have selected Require Addenda, and you want to disable this feature, scan Don't Require Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don't Require Addenda.
* Don't Require Addenda
168
Granit XP User Guide
Require 5 Digit Addenda
Require 2 Digit Addenda
Require 2 or 5 Digit Addenda
EAN-13 Beginning with 414/419 Addenda Required
This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a "414" or "419." The following settings can be programmed:
Require Addenda: All EAN-13 barcodes that begin with a "414" or "419" must have a 2 digit addenda, a 5 digit addenda, or a combination of these addenda. The EAN13 barcode with the addenda is then transmitted as a single, concatenated barcode. If the required addenda is not found within the Addenda Timeout period, the EAN-13 barcode is discarded.
Don't Require Addenda: If you have selected Require Addenda, and you want to disable this feature, scan Don't Require Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required.
Default = Don't Require Addenda.
* Don't Require Addenda
Require 5 Digit Addenda
Require 2 Digit Addenda Require 2 or 5 Digit Addenda
Granit XP User Guide
169
EAN-13 Beginning with 434/439 Addenda Required
This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 barcodes that begin with a "434" or "439." The following settings can be programmed:
Require Addenda: All EAN-13 barcodes that begin with a "434" or "439" must have a 2 digit addenda, a 5 digit addenda, or a combination of these addenda. The EAN13 barcode with the addenda is then transmitted as a single, concatenated barcode. If the required addenda is not found within the Addenda Timeout period, the EAN-13 barcode is discarded.
Don't Require Addenda: If you have selected Require Addenda, and you want to disable this feature, scan Don't Require Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required.
Default = Don't Require Addenda.
* Don't Require Addenda
Require 5 Digit Addenda
Require 2 Digit Addenda
Require 2 or 5 Digit Addenda
EAN-13 Beginning with 977 Addenda Required
This setting programs the scanner to require a 2 digit addenda only on EAN-13 barcodes that begin with "977." The following settings can be programmed:
Require 2 Digit Addenda: All EAN-13 barcodes that begin with "977" must have a 2 digit addendum. The EAN-13 barcode with the 2 digit addendum is then transmitted as a single, concatenated barcode. If a 2 digit addendum is not found within the Addenda Timeout period, the EAN-13 barcode is discarded.
Don't Require 2 Digit Addenda: If you have selected Require 2 Digit Addenda, and you want to disable this feature, scan Don't Require 2 Digit Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required.
170
Granit XP User Guide
Default = Don't Require 2 Digit Addenda.
* Don't Require 2 Digit Addenda
Require 2 Digit Addenda
EAN-13 Beginning with 978 Addenda Required
These settings program the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with "978." The following settings can be programmed: Require 5 Digit Addenda: All EAN-13 barcodes that begin with "978" must have a 5 digit addendum. The EAN-13 barcode with the 5 digit addendum is then transmitted as a single, concatenated barcode. If a 5 digit addendum is not found within the Addenda Timeout period, the EAN-13 barcode is discarded. Don't Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don't Require 5 Digit Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don't Require 5 Digit Addenda.
* Don't Require 5 Digit Addenda
Require 5 Digit Addenda
EAN-13 Beginning with 979 Addenda Required
These settings program the scanner to require a 5 digit addenda only on EAN-13 barcodes that begin with "979." The following settings can be programmed:
Require 5 Digit Addenda: All EAN-13 barcodes that begin with "979" must have a 5 digit addendum. The EAN-13 barcode with the 5 digit addendum is then transmitted as a single, concatenated barcode. If a 5 digit addendum is not found within the Addenda Timeout period, the EAN-13 barcode is discarded.
Don't Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don't Require 5 Digit Addenda. EAN-13 barcodes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required.
Granit XP User Guide
171
Default = Don't Require 5 Digit Addenda.
* Don't Require 5 Digit Addenda
Require 5 Digit Addenda
Addenda Timeout
You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-13 Addenda Required. Set the length (in milliseconds) for this timeout by scanning the barcode below, then setting the timeout (from 0-500 milliseconds) by scanning digits from the Programming Chart, beginning on page 291 of this manual, then Save. Default = 120. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches.
Addenda Timeout
EAN/JAN-13 Addenda Separator
When this feature is On, there is a space between the data from the barcode and the data from the addenda. When turned Off, there is no space. Default = On.
* On
Off
Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/ EAN-13 with Extended Coupon Code (page 161).
172
Granit XP User Guide
ISBN Translate
When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off.
On
EAN/JAN-8
* Off
<Default All EAN/JAN-8 Settings>
EAN/JAN-8 On/Off
* On
Off
EAN/JAN-8 Check Digit
This selection allows you to specify whether or not the check digit should be transmitted at the end of the scanned data. Default = On.
* On
Off
Granit XP User Guide
173
EAN/JAN-8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN-8 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-8 barcodes that have addenda. Default = Not Required.
Required
* Not Required
Addenda Timeout
You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-8 Addenda Required. Set the length (in milliseconds) for this timeout by scanning the barcode below, then set-
174
Granit XP User Guide
ting the timeout (from 0-120 milliseconds) by scanning digits from the Programming Chart, beginning on page 291 of this manual, then Save. Default = 500.
Note: The Addenda Timeout setting is applied to all addenda and coupon code searches.
Addenda Timeout
EAN/JAN-8 Addenda Separator
When this feature is On, there is a space between the data from the barcode and the data from the addenda. When turned Off, there is no space. Default = On.
MSI
* On Off
<Default All MSI Settings>
MSI On/Off
On * Off
Granit XP User Guide
175
MSI Check Character
Different types of check characters are used with MSI barcodes. You can program the scanner to read MSI barcodes with Type 10 check characters. Default = Validate Type 10, but Don't Transmit.
When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI barcodes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
When Check Character is set to Validate Type 10/11, but Don't Transmit, the unit will only read MSI barcodes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data.
* Validate Type 10, but Don't Transmit
Validate 2 Type 10 Characters, but Don't Transmit
Validate Type 11 then Type 10 Character, but Don't Transmit
Disable MSI Check Characters
Validate Type 10 and Transmit
Validate 2 Type 10 Characters and Transmit
Validate Type 11 then Type 10 Character and Transmit
176
Granit XP User Guide
MSI Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
GS1 DataBar Omnidirectional
< Default All GS1 DataBar Omnidirectional Settings >
GS1 DataBar Omnidirectional On/Off
* On
Off
Granit XP User Guide
177
GS1 DataBar Limited
< Default All GS1 DataBar Limited Settings >
GS1 DataBar Limited On/Off
* On
Off
GS1 DataBar Expanded
< Default All GS1 DataBar Expanded Settings >
GS1 DataBar Expanded On/Off
* On
Off
GS1 DataBar Expanded Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.
178
Minimum Message Length
Granit XP User Guide
Maximum Message Length
Trioptic Code
Note: If you are going to scan Code 32 Pharmaceutical codes (page 145), Trioptic Code must be off. Trioptic Code is used for labeling magnetic storage media.
On
Codablock A
* Off
<Default All Codablock A Settings>
Codablock A On/Off
On
* Off
If you are reading Code 39 barcodes, Codablock A should remain disabled. If you are enabling Codablock A, you should disable Code 39 (see Code 39 on page 143).
Granit XP User Guide
179
Codablock A Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600.
Minimum Message Length
Codablock F
Maximum Message Length
<Default All Codablock F Settings>
Codablock F On/Off
On
* Off
If you are reading Code 128 barcodes, Codablock F should remain disabled. If you are enabling Codablock F, you should disable Code 128 (see Code 128 on page 155).
Codablock F Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
Minimum Message Length
180
Granit XP User Guide
Maximum Message Length
Label Code
The standard Label Code is used in libraries. Default = Off.
On *Off
PDF417
< Default All PDF417 Settings >
PDF417 On/Off
* On Off
Granit XP User Guide
181
PDF417 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.
Minimum Message Length
Maximum Message Length
MacroPDF417
MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 barcodes. When this selection is enabled, these multiple barcodes are assembled into a single data string. Default = On.
* On
Off
MicroPDF417
< Default All MicroPDF417 Settings >
MicroPDF417 On/Off
On
182
Granit XP User Guide
* Off
MicroPDF417 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366.
Minimum Message Length
Maximum Message Length
GS1 Composite Codes
Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology. GS1 Composite symbologies allow for the co-existence of symbologies already in use. Default = Off.
On
* Off
Granit XP User Guide
183
UPC/EAN Version
Scan the UPC/EAN Version On barcode to decode GS1 Composite symbols that have a U.P.C. or an EAN linear component. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Version Off.
UPC/EAN Version On
* UPC/EAN Version Off
Note: If you scan coupons that have both UPC and GS1 Databar codes, you may wish to scan and output only the data from the GS1 Databar code. See Coupon GS1 DataBar Output (page 162) for further information.
GS1 Composite Code Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-2435. Minimum Default = 1, Maximum Default = 2435.
Minimum Message Length
Maximum Message Length
GS1 Emulation
The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1128, and GS1 DataBar and GS1 Composites. (Any application that accepts GS1 data can be simplified since it only needs to recognize one data carrier type.) If GS1-128 Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM ID is enabled, the value will be the GS1128 AIM ID, ]C1 (see Symbology Charts on page 279). If GS1 DataBar Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM ID is enabled, the value will be the GS1-DataBar AIM ID, ]em (see Symbology Charts on page 279).
184
Granit XP User Guide
If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPCE expansion is controlled by the UPC-E0 Expand (page 163) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts on page 279). If EAN8 to EAN13 Conversion is scanned, all EAN8 barcodes are converted to EAN13 format. Default = GS1 Emulation Off.
GS1-128 Emulation
GS1 DataBar Emulation
GS1 Code Expansion Off
EAN8 to EAN13 Conversion
* GS1 Emulation Off
TCIF Linked Code 39 (TLC39)
This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All barcode readers are capable of reading the Code 39 linear component. The MicroPDF417 component can only be decoded if TLC39 On is selected. The linear component may be decoded as Code 39 even if TLC39 is off. Default = Off.
On
* Off
Granit XP User Guide
185
QR Code
< Default All QR Code Settings >
QR Code On/Off
This selection applies to both QR Code and Micro QR Code.
* On
Off
QR Code Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089.
Minimum Message Length
Maximum Message Length
QR Code Append
This function allows the scanner to append the data from several QR Code barcodes together before transmitting them to the host computer. When the scanner encounters an QR Code barcode with the append trigger character(s), it buffers the number of QR Code barcodes determined by information encoded in those barcodes. Once the proper number of codes is reached, the data is output in the order specified in the barcodes. There are 3 ways to scan appended QR Code: One Scan: Pull the trigger one time and all appended QR Codes in the same image are decoded.
186
Granit XP User Guide
Swipe: Pull and hold down the trigger and scan all appended QR Codes while keeping the trigger pressed. The scanner emits short beeps for each partial QR Code that is scanned and buffered. One long beep is emitted after the last QR Code is scanned and the data is complete. Not compatible with Presentation mode.
Point and Shoot: Pull the trigger one time for each image. The scanner emits a short beep for each partial QR Code that is scanned and buffered. One long beep is emitted after the last QR Code is scanned and the data is complete. Not compatible with Presentation mode.
Default = One Scan.
* One Scan Point and Shoot
Swipe Off
QR Code Page
QR Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the barcode below, select the code page with which the barcodes were created (see ISO 2022/ISO 646 Character Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly.
QR Code Page
Granit XP User Guide
187
QR Code with Web Link
Use this function to enable or disable the scanning of QR codes that contain "http" or "https". Default = On.
*On
DotCode
Off
< Default All DotCode Settings >
DotCode On/Off
On
* Off
Poor Quality DotCodes
This setting improves the scanner's ability to read damaged or badly printed DotCodes. Default = Poor Quality DotCodes Off.
Poor Quality DotCodes On
* Poor Quality DotCodes Off
188
Granit XP User Guide
DotCode Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-2400. Minimum Default = 1, Maximum Default = 2400.
Minimum Message Length
Maximum Message Length
Digimarc BarcodeTM
Digimarc Decoder Attempts
Set the number of attempts by scanning the barcode below, then setting the number of attempts (0-10) by scanning digits from the Programming Chart beginning on page 291 of this manual, the Save. Minimum to Maximum attempts = 0-10. Default = 3.
Digimarc Decoder Attempts
Digimarc Barcode
This setting programs the scanner to decode Digimarc Barcode using Digimarc and ID decoders. When Digimarc Barcode is set to On, the Digimarc decoder is used on most frames and the ID decoder will read every fifth frame. When Digimarc Barcode is set to Uses ID Decoder then Both Decoders, the ID decoder will read the number of attempts set by the Digimarc Decoder Attempts and then will use both ID and Digimarc decoders. When Digimarc Barcode is set to Uses Digimarc Decoder then Both Decoders, the Digimarc decoder will read the number of attempts set by the Digimarc Decoder Attempts and then will use both ID and Digimarc decoders. When Digimarc Barcdoe is set to Uses ID Decoder then Alternates Decoders, the ID decoder will read the number of attempts set by the Digimarc Decoder Attempts and then will alternate between ID and Digimarc decoders. When Digimarc Barcode is set to Uses Digimarc Decoder then Alternates Decoders, the Digimarc decoder will read the number of attempts set by the Digimarc Decoder Attempts and then will alternate between ID and Digimarc decoders.
Granit XP User Guide
189
Default = Off.
*Off
On
Uses ID Decoder then Both Decoders
Uses ID Decoder then Alternates Decoders
Uses Digimarc Decoder then Both Decoders
Data Matrix
Uses Digimarc Decoder then Alternates Decoders
< Default All Data Matrix Settings >
Data Matrix On/Off
* On
190
Off
Granit XP User Guide
Direct Part Marking Decoding
If you are having trouble reading Direct Part Marking (DPM) barcodes, scan Dotpeen DPM Decoding for Dotpeen codes or scan Reflective (Etched) DPM Decoding for reflective (etched) codes. Default = Disable DPM Decoding.
Dotpeen DPM Decoding
* Disable DPM Decoding
Reflective (Etched) DPM Decoding
Data Matrix Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116.
Minimum Message Length
Maximum Message Length
Data Matrix Code Page
Data Matrix Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the barcode below, select the code page with which the barcodes were created (see ISO 2022/ISO 646
Granit XP User Guide
191
Character Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly.
MaxiCode
Data Matrix Code Page
< Default All MaxiCode Settings >
MaxiCode On/Off
On
* Off
MaxiCode Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.
Minimum Message Length
Maximum Message Length
192
Granit XP User Guide
Aztec Code
< Default All Aztec Code Settings >
Aztec Code On/Off
* On
Off
Aztec Code Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832.
Minimum Message Length
Maximum Message Length
Aztec Append
This function allows the scanner to append the data from several Aztec barcodes together before transmitting them to the host computer. When the scanner encounters an Aztec barcode with the append trigger character(s), it buffers the number of Aztec barcodes determined by information encoded in those barcodes. Once the proper number of codes is reached, the data is output in the order specified in the barcodes. Default = On.
* On
Granit XP User Guide
193
Off
Aztec Code Page
Aztec Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, scan the barcode below, select the code page with which the barcodes were created (see ISO 2022/ISO 646 Character Replacements on page 286), and scan the value and the Save barcode from the Programming Chart, beginning on page 291. The data characters should then appear properly.
Aztec Code Page
Chinese Sensible (Han Xin) Code
< Default All Han Xin Settings >
Han Xin Code On/Off
On
* Off
194
Granit XP User Guide
Han Xin Code Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833.
Minimum Message Length
Maximum Message Length
Postal Codes - 2D
The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed. Only one 2D postal code selection can be active at a time. If you scan a second 2D postal code selection, the first selection is overwritten. Default = 2D Postal Codes Off.
Single 2D Postal Codes:
* 2D Postal Codes Off
Australian Post On Canadian Post On
British Post On Intelligent Mail Barcode On
Granit XP User Guide
195
Japanese Post On
Planet Code On
Also see Planet Code Check Digit, page 198.
Postnet On
Also see Postnet Check Digit, page 199.
InfoMail On
Combination 2D Postal Codes:
InfoMail and British Post On
196
KIX Post On Postal-4i On Postnet with B and B' Fields On
Intelligent Mail Barcode and Postnet with B and B' Fields On
Granit XP User Guide
Postnet and Postal-4i On
Postal-4i and Intelligent Mail Barcode On
Planet Code and Postnet On
Planet Code and Postal-4i On
Planet Code, Postnet, and Postal-4i On
Granit XP User Guide
Postnet and Intelligent Mail Barcode On
Postal-4i and Postnet with B and B' Fields On
Planet Code and Postnet with B and B' Fields On
Planet Code and Intelligent Mail Barcode
On
Planet Code, Postnet, and Intelligent Mail Barcode On
197
Planet Code, Postal-4i, and Intelligent Mail Barcode On
Postnet, Postal-4i, and Intelligent Mail Barcode On
Planet Code, Postal-4i, and Postnet with B and B' Fields On
Planet Code, Intelligent Mail Barcode, and Postnet with B and B' Fields On
Postal-4i, Intelligent Mail Barcode, and Postnet with B and B' Fields On
Planet Code, Postal-4i,
Intelligent Mail Barcode, and Postnet On
Planet Code, Postal-4i,
Intelligent Mail Barcode, and Postnet with B and B' Fields On
Planet Code Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default = Don't Transmit.
Transmit Check Digit
198
Granit XP User Guide
* Don't Transmit Check Digit
Postnet Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data. Default = Don't Transmit.
Transmit Check Digit
* Don't Transmit Check Digit
Australian Post Interpretation
This option controls what interpretation is applied to customer fields in Australian 4-State symbols. Bar Output lists the bar patterns in "0123" format. Numeric N Table causes that field to be interpreted as numeric data using the N Table. Alphanumeric C Table causes the field to be interpreted as alphanumeric data using the C Table. Refer to the Australian Post Specification Tables. Combination C and N Tables causes the field to be interpreted using either the C or N Tables. Default = Bar Output.
* Bar Output
Numeric N Table
Alphanumeric C Table
Granit XP User Guide
199
Combination C and N Tables
Postal Codes - Linear
The following lists linear postal codes. Any combination of linear postal code selections can be active at a time.
China Post (Hong Kong 2 of 5)
<Default All China Post (Hong Kong 2 of 5) Settings>
China Post (Hong Kong 2 of 5) On/Off
On
* Off
China Post (Hong Kong 2 of 5) Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
200
Granit XP User Guide
Korea Post
<Default All Korea Post Settings>
Korea Post
On
* Off
Korea Post Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 140) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Korea Post Check Digit
This selection allows you to specify whether the check digit should be transmitted or not. Default = Don't Transmit.
Transmit Check Digit
* Don't Transmit Check Digit
Granit XP User Guide
201
202
Granit XP User Guide
CHAPTER
8 IMAGING COMMANDS
The scanner is like a digital camera in the way it captures, manipulates, and transfers images. The following commands allow you to alter the way the scanner performs these functions.
Single-Use Basis
Imaging Commands with their modifiers send instructions to the scanner on a single-use basis, and take effect for a single image capture. Once that capture is complete, the scanner reverts to its imaging default settings. If you want to permanently change a setting, you must use the serial default commands (see Chapter 10). When the serial default command is used, that selection becomes the new, permanent setting for the scanner.
Command Syntax
Multiple modifiers and commands can be issued within one sequence. If additional modifiers are to be applied to the same command, just add the modifiers to that command. For example, to add 2 modifiers to the Image Snap command, such as setting the Imaging Style to 1P and the Wait for Trigger to 1T, you would enter IMGSNP1P1T.
Note: After processing an image capture command (IMGSNP or IMGBOX), you must follow it with an IMGSHP command if you want to see it on your terminal.
To add a command to a sequence, each new command is separated with a semicolon. For example, to add the Image Ship command to the above sequence, you would enter IMGSNP1P1T;IMGSHP.
The imaging commands are:
Image Snap - IMGSNP (page 204)
Image Ship - IMGSHP (page 207)
Intelligent Signature Capture - IMGBOX (page 216)
Granit XP User Guide
203
The modifiers for each of these commands follow the command description.
Note: The images included with each command description are examples only. The results you achieve may be different from those included in this manual. The quality of the output you receive will vary depending on lighting, quality of the initial image/object being captured, and distance of the scanner from the image/object. To achieve a high quality image, it is recommended that you position your scanner 4-6" (10.2-15.2 cm) away from the image/object you are capturing.
Step 1 - Take a Picture Using IMGSNP
Image Snap - IMGSNP
An image is taken whenever the hardware trigger is pressed, or when the Image Snap (IMGSNP) command is processed.
The image snap command has many different modifiers that can be used to change the look of the image in memory. Any number of modifiers may be appended to the IMGSNP command.
Example: You can use the following command to snap an image, increase the gain, and have the beeper sound once the snap is complete: IMGSNP2G1B
IMGSNP Modifiers
P - Imaging Style
This sets the Image Snap style.
0P Decoding Style. This processing allows a few frames to be taken until the exposure parameters are met. The last frame is then available for further use.
1P Photo Style (default). This mimics a simple digital camera, and results in a visually optimized image.
2P Manual Style. This is an advanced style that should only be used by an experienced user. It allows you the most freedom to set up the scanner, and has no auto-exposure.
B - Beeper
Causes a beep to sound after an image is snapped. 0B No beep (default) 1B Sounds a beep when the image is captured.
204
Granit XP User Guide
T - Wait for Trigger
Waits for a hardware trigger press before taking the image. This is only available when using Photo Style (1P).
0T Takes image immediately (default)
1T Waits for a trigger press, then takes the image
L - LED State
Determines if the LEDs should be on or off, and when. Ambient illumination (0L) is preferred for taking pictures of color documents, such as ID cards, especially when the scanner is in a stand. LED illumination (1L) is preferred when the scanner is handheld. LED State is not available when using Decoding Style (0P).
0L LEDs off (default)
1L LEDs on
E - Exposure
Exposure is used in Manual Style only (2P), and allows you to set the exposure time. This is similar to setting a shutter speed on a camera. The exposure time determines how long the scanner takes to record an image. On a bright day, exposure times can be very short because plenty of light is available to help record an image. At nighttime, exposure time can increase dramatically due to the near absence of light. Units are 127 microseconds. (Default = 7874)
nE Range: 1 - 7874
Example:
Exposure at 7874E with fluorescent lighting:
Exposure at 100E with fluorescent lighting:
Granit XP User Guide
205
G - Gain
Gain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel value. As you increase the gain, the noise in an image is also amplified.
1G No gain (default)
2G Medium gain
4G Heavy gain
8G Maximum gain
Example: Gain at 1G:
Gain at 4G:
Gain at 8G:
W - Target White Value
Sets the target for the median grayscale value in the captured image. For capturing close-up images of high contrast documents, a lower setting, such as 75, is recommended. Higher settings result in longer exposure times and brighter images, but if the setting is too high, the image may be overexposed. Target White Value is only available when using Photo Style (1P). (Default = 125)
nW Range: 0 - 255
Example:
White Value at 75W:
White Value at 125W: White Value at 200W:
D - Delta for Acceptance
This sets the allowable range for the white value setting (see W - Target White Value). Delta is only available when using Photo Style (1P). (Default = 25)
nD Range: 0 - 255
206
Granit XP User Guide
U - Update Tries
This sets the maximum number of frames the scanner should take to reach the D Delta for Acceptance. Update Tries is only available when using Photo Style (1P). (Default = 6)
nU Range: 0 - 10
% - Target Set Point Percentage
Sets the target point for the light and dark values in the captured image. A setting of 75% means 75% of the pixels are at or below the target white value, and 25% of the pixels are above the target white value. Altering this setting from the default is not recommended under normal circumstances. To alter grayscale values, W Target White Value should be used. (Default = 50)
n% Range: 1 - 99
Example:
Target Set Point
Target Set Point
Target Set Point
Percentage at 97%: Percentage at 50%: Percentage at 40%:
Step 2 - Ship a Picture Using IMGSHP
Image Ship - IMGSHP
An image is taken whenever the trigger is pressed or when the Image Snap (IMGSNP) command is processed. The last image is always stored in memory. You can "ship" the image by using the IMGSHP command.
The image ship commands have many different modifiers that can be used to change the look of the image output. Modifiers affect the image that is transmitted, but do not affect the image in memory. Any number of modifiers may be appended to the IMGSHP command.
Example: You can use the following command to snap and ship a bitmap image with gamma correction and document image filtering: IMGSNP;IMGSHP8F75K26U
Granit XP User Guide
207
IMGSHP Modifiers
A - Infinity Filter
Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with IMGSNP Modifiers (page 204).
0A Infinity filter off (default)
1A Infinity filter on
Example:
Infinity Filter off (0A) from approximately 12 feet (3.66m) away:
Infinity Filter on (1A) from approximately 12 feet (3.66m) away:
C - Compensation
Flattens the image to account for variations in illumination across the image.
0C Compensation disabled (default)
1C Compensation enabled
Example: Compensation at 0C:
Compensation at 1C:
D - Pixel Depth
Indicates the number of bits per pixel in the transmitted image (KIM or BMP format only).
8D 8 bits per pixel, grayscale image (default)
1D 1 bit per pixel, black and white image
208
Granit XP User Guide
E - Edge Sharpen
An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen filter can be entered from 1 to 24. Entering a 23E gives the sharpest edges, but also increases noise in the image.
0E Don't sharpen image (default)
14E Apply edge sharpen for typical image
ne Apply edge sharpen using strength n (n = 1-24)
Example: Edge Sharpen at 0E:
Edge Sharpen at 24E:
F - File Format
Indicates the desired format for the image. 0F KIM format 1F TIFF binary 2F TIFF binary group 4, compressed 3F TIFF grayscale 4F Uncompressed binary (upper left to lower right, 1 pixel/bit, 0 padded end of line) 5F Uncompressed grayscale (upper left to lower right, bitmap format) 6F JPEG image (default) 8F BMP format (lower right to upper left, uncompressed) 15F BMP Uncompressed raw image
Granit XP User Guide
209
H - Histogram Stretch
Increases the contrast of the transmitted image. Not available with some image formats.
0H No stretch (default)
1H Histogram stretch
Example: Histogram Stretch at 0H:
Histogram Stretch at 1H:
I - Invert Image
Invert image is used to rotate the image around the X or Y axis.
1ix Invert around the X axis (flips picture upside down)
1iy Invert around the Y axis (flips picture left to right)
Example:
Image not inverted: Image with Invert Image set to 1ix:
Image with Invert Image set to 1iy:
210
Granit XP User Guide
IF- Noise Reduction
Used to reduce the salt and pepper noise in an image.
0if No salt and pepper noise reduction (default)
1if Salt and pepper noise reduction
Example: Noise Reduction Off (0if):
Noise Reduction On (1if):
IR - Image Rotate
0ir Image as snapped (rightside up) (default)
1ir Rotate image 90 degrees to the right
2ir Rotate image 180 degrees (upside down)
3ir Rotate image 90 degrees to the left
Example: Image Rotate set to 0ir:
Image Rotate set to 2ir:
Image Rotate set to 1ir:
Image Rotate set to 3ir:
Granit XP User Guide
211
J - JPEG Image Quality
Sets the desired quality when the JPEG image format is selected. Higher numbers result in higher quality, but larger files. Smaller numbers result in greater amounts of lossy compression, faster transmission times, lower quality, but smaller files. (Default = 50)
nJ Image is compressed as much as possible while preserving quality factor of n (n = 0 - 100)
0J worst quality (smallest file)
100J best quality (largest file)
K - Gamma Correction
Gamma measures the brightness of midtone values produced by the image. You can brighten or darken an image using gamma correction. A higher gamma correction yields an overall brighter image. The lower the setting, the darker the image. The optimal setting for text images is 50K.
0K Gamma correction off (default)
50K Apply gamma correction for brightening typical document image
nK Apply gamma correction factor n (n = 0-1,000)
Example:
Gamma Correction set to 0K:
Gamma Correction set to 50K:
Gamma Correction set to 255K:
L, R, T, B, M - Image Cropping
Ships a window of the image by specifying the left, right, top, and bottom pixel coordinates. Device columns are numbered 0 through 1279, and device rows are numbered 0 through 959.
nL The left edge of the shipped image corresponds to column n of the image in memory. Range: 000 - 843. (Default = 0)
nR The right edge of the shipped image corresponds to column n - 1 of the image in memory. Range: 000 - 843. (Default = all columns)
nT The top edge of the shipped image corresponds to row n of the image in memory. Range: 000 - 639. (Default = 0)
212
Granit XP User Guide
Example:
nB The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 639. (Default = all rows)
Uncropped Image:
Image Crop set to 300R:
Image Crop set to 300L:
Image Crop set to 200B:
Image Crop set to 200T:
Alternately, specify the number of pixels to cut from the outside margin of the image; thus only the center pixels are transmitted.
nM Margin: cut n columns from the left, n + 1 columns from the right, n rows from the top, and n + 1 rows from the bottom of the image. Ship the remaining center pixels. Range: 0 - 238. (Default = 0, or full image)
Example: Image Crop set to 238M:
P - Protocol
Used for shipping an image. Protocol covers two features of the image data being sent to the host. It addresses the protocol used to send the data (Hmodem, which is an Xmodem 1K variant that has additional header information), and the format of the image data that is sent.
0P None (raw data)
2P None (default for USB)
3P Hmodem compressed (default for RS232)
4P Hmodem
S - Pixel Ship
Pixel Ship sizes an image in proportion to its original size. It decimates the image by shipping only certain, regularly spaced pixels.
Example: 4S would transmit every fourth pixel from every fourth line.
Granit XP User Guide
213
The smaller number of pixels shipped, the smaller the image, however, after a certain point the image becomes unusable.
1S ship every pixel (default)
2S ship every 2nd pixel, both horizontally and vertically
3S ship every 3rd pixel, both horizontally and vertically
Example:
Pixel Ship set to 1S:
Pixel Ship set to 2S:
Pixel Ship set to 3S:
Pixel Ship set to 4S:
U - Document Image Filter
Allows you to input parameters to sharpen the edges and smooth the area between the edges of text in an image. This filter should be used with gamma correction (see page 212), with the scanner in a stand, and the image captured using the command:
IMGSNP1P0L168W90%32D
This filter typically provides better JPEG compression than the standard E - Edge Sharpen command (see page 215). This filter also works well when shipping pure black and white images (1 bit per pixel). The optimal setting is 26U.
0U Document image filter off (default)
26U Apply document image filter for typical document image
nU Apply document image filter using grayscale threshold n. Use lower numbers when the image contrast is lower. 1U will have a similar effect to setting E - Edge Sharpen (page 209) to 22e. Range: 0-255.
Example:
Document Image Filter set to 0U: Document Image Filter set to 26U:
214
Granit XP User Guide
V - Blur Image
Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image.
0V Don't blur (default)
1V Blur
Example:
Blur Image Off (0V):
Blur Image On (1V):
W - Histogram Ship
A histogram gives a quick picture of the tonal range of an image, or key type. A lowkey image has detail concentrated in the shadows; a high-key image has detail concentrated in the highlights; and an average-key image has detail concentrated in the midtones. This modifier ships the histogram for an image.
0W Don't ship histogram (default)
1W Ship histogram
Example: Image used for histogram:
Histogram of image:
Image Size Compatibility
If you have applications that expect an image ship to return exactly 640x480 pixels, scan the Force VGA Resolution barcode. Default = Native Resolution.
Force VGA Resolution
Granit XP User Guide
215
* Native Resolution
Intelligent Signature Capture - IMGBOX
IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a barcode. This allows you to tailor a signature capture area to a specific form. In order to use IMGBOX, you need a set form where the signature box location is in a known location relative to a barcode. You can input the overall size of the signature area, as well as specify how far the signature area is from the barcode, vertically and horizontally. You can also set the resolution and file format for the final output of the signature capture image.
Note: IMGBOX commands can only be triggered by one of the following types of barcodes: PDF417, Code 39, Code 128, Aztec, Codabar, and Interleaved 2 of 5. Once one of these symbologies has been read, the image is retained for a possible IMGBOX command.
Signature Capture Optimize
If you will be using your scanner to capture signatures frequently, you should optimize it for this purpose. However, the speed of scanning barcodes may be slowed when this mode is enabled. Default = Off.
Optimize On
* Optimize Off
Below is an example of a signature capture application. In this example, the aimer is centered over the signature capture area and the trigger is pressed. A single beep is emitted, indicating that the scanner has read a Code 128 barcode and the data has been transferred to the host. An IMGBOX command may now be sent from the host to specify the coordinates of the signature capture area below that code, and indicating that only that area containing the signature should be transferred as an image to the host.
216
Granit XP User Guide
To see this example, align the aimer with the signature area (not with the barcode), then press the trigger.
Send the following IMGBOX command string after the trigger press: Example: IMGBOX245w37h55y.
Note: Case is not important in the command string. It is used here only for clarity. The following image is captured:
The IMGBOX commands have many different modifiers that can be used to change the size and appearance of the signature image output by the scanner. Modifiers affect the image that is transmitted, but do not affect the image in memory. Any number of modifiers may be appended to the IMGBOX command. Note: The IMGBOX command will return a NAK unless a window size (width and height) are specified. See H - Height of Signature Capture Area (page 219) and W - Width of Signature Capture Area (page 220).
IMGBOX Modifiers
A - Output Image Width
This option is used to size the image horizontally. If using this option, set the resolution (R) to zero. Example: Image Width set to 200A:
Image Width set to 600A:
Granit XP User Guide
217
B - Output Image Height
This option is used to size the image vertically. If using this option, set the resolution (R) to zero.
Example:
Image Height set to 50B:
Image Height set to 100B:
D - Pixel Depth
This indicates the number of bits per pixel in the transmitted image, which defines whether it will be grayscale or black and white.
8D 8 bits per pixel, grayscale image (default) 1D 1 bit per pixel, black and white image
F - File Format
This option indicates the type of file format in which to save the image. 0F KIM format 1F TIFF binary 2F TIFF binary group 4, compressed 3F TIFF grayscale 4F Uncompressed Binary 5F Uncompressed grayscale 6F JPEG image (default) 7F Outlined image 8F BMP format
218
Granit XP User Guide
H - Height of Signature Capture Area
The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5.
Example: IMGBOX245w37h55y.
K - Gamma Correction
Gamma measures the brightness of midtone values produced by the image. You can brighten or darken an image using gamma correction. A higher gamma correction yields an overall brighter image. The lower the setting, the darker the image. The optimal setting for text images is 50K.
0K Gamma correction off (default) 50K Apply gamma correction for brightening typical document image nK Apply gamma correction factor n (n = 1-255)
Example: Gamma Correction set to 0K:
Gamma Correction set to 50K:
Gamma Correction set to 255K:
R - Resolution of Signature Capture Area
The resolution is the number of pixels that the scanner outputs per each minimum bar width. The higher the value for R, the higher the quality of the image, but also the larger the file size. Values begin at 1000. The scanner automatically inserts a
Granit XP User Guide
219
decimal point between the first and second digit. For example, use 2500 to specify a resolution of 2.5. Set to zero when using the A and B modifiers (see A - Output Image Width and B - Output Image Height on page 218). Example: Resolution set to 0R:
Resolution set to 1000R:
Resolution set to 2000R:
S - Barcode Aspect Ratio
All dimensions used in IMGBOX are measured as multiples of the minimum element size of the barcode. The barcode aspect ratio allows you to set the ratio of the barcode height to the narrow element width. In the example, the narrow element width is .010 inches and the barcode height is 0.400 inches, resulting in a value of S = 0.4/0.01 = 40.
W - Width of Signature Capture Area
The width of the signature capture area must be measured in inches divided by .01. In the example, the width of the area to be captured is 2.4 inches, resulting in a value of W = 2.4/0.01 = 240. (A value of 245 was used in the example to accommodate a slightly wider image area.)
Example: IMGBOX245w37h55y.
X - Horizontal Barcode Offset
The horizontal barcode offset allows you to offset the horizontal center of the signature capture area. Positive values move the horizontal center to the right and negative values to the left. Measurements are in multiples of the minimum bar width.
Example:
Horizontal Offset set to 75X:
Horizontal Offset set to -75X:
220
Granit XP User Guide
Y - Vertical Barcode Offset
The vertical barcode offset allows you to offset the vertical center of the signature capture area. Negative numbers indicate that the signature capture is above the barcode, and positive numbers indicate that the area is below the barcode. Measurements are in multiples of the minimum bar width
Example:
Vertical Offset set to -7Y:
.
Vertical Offset set to 65Y:
RF Default Imaging Device
The scanner supports imaging command processing (IMGSHP, IMGSNP, IMGBOX) so that EZConfig for Scanning (see page 225) and other applications are able to perform imaging functions as if they were communicating directly with a scanner. To accomplish this, the scanner uses a menu command called RF_DID (RF Default Imaging Device). RF_DID is the name of the scanner (BT_NAM) that is to receive imaging commands. The default for RF_DID is "*"indicating that imaging commands are to be sent to all associated scanners. Change this setting to RF_DIDscanner_name to ensure that they are sent to a particular scanner. Refer to "Page" on page 3-50 to generate a report containing the port, work group, scanner name, and address for each scanner. Refer to "Scanner Name" on page 3-64 set a unique name for each scanner.
Granit XP User Guide
221
222
Granit XP User Guide
CHAPTER
9 UTILITIES
To Add a Test Code I.D. Prefix to All Symbologies
This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page 279 for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power cycled.
Add Code I.D. Prefix to All Symbologies (Temporary)
Show Software Revision
Scan the barcode below to output the current software revision, unit serial number, and other product information for both the scanner and base.
Show Software Revision
Test Menu
When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code. The programming function will still occur, but in addition, the content of that programming code is output to the terminal. Note: This feature should not be used during normal scanner operation.
Granit XP User Guide
223
On
* Off
TotalFreedom
TotalFreedom is an open system architecture that makes it possible for you create applications that reside on your scanner. Decoding apps and Data Formatting apps can be created using TotalFreedom. For further information about TotalFreedom, go to our website at sps.honeywell.com.
Application Plug-Ins (Apps)
Any apps that you are using can be turned off or on by scanning the following barcodes. Apps are stored in groups: Decoding, and Formatting. You can enable and disable these groups of apps by scanning that group's On or Off barcode below. You can also scan the List Apps barcode to output a list of all your apps.
* Decoding Apps On
Decoding Apps Off
* Formatting Apps On
Formatting Apps Off
List Apps
Note: You must reset your device in order for the apps setting to take effect.
224
Granit XP User Guide
EZConfig for Scanning Introduction
EZConfig for Scanning provides a wide range of PC-based programming functions that can be performed on the scanner connected to your PC. EZConfig for Scanning allows you to download upgrades to the scanner's firmware, change programmed parameters, and create and print programming barcodes. Using EZConfig for Scanning, you can even save/open the programming parameters. This saved file can be e-mailed or, if required, you can create a single barcode that contains all the customized programming parameters and mail or fax that barcode to any location. Users in other locations can scan the barcode to load in the customized programming.
Configure with EZConfig for Scanning
Use the EZConfig for Scanning tool to configure your scanner online:
1. Access the Honeywell Technical Support Downloads Portal at honeywell.com/ PSSsoftware-downloads.
2. Go to Software > Barcode Scanners > Software > Tools and Utilities > EZConfig for Scanning > Current.
3. Download the Setup version of EZConfig for Scanning. 4. Open EZConfig to configure your scanner.
Granit XP User Guide
225
Reset the Factory Defaults
Caution: This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins.
If you aren't sure what programming options are in your scanner, or you've changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults barcode, then scan Activate Defaults. This resets the scanner to the factory default settings.
Remove Custom Defaults
Activate Defaults
Note: If using a cordless system, scanning the Activate Defaults barcode also causes both the scanner and the base or Access Point to perform a reset and become unlinked. The scanner must be placed in its base to re-establish the link before any setup codes are entered. If using an Access Point, the linking barcode must be scanned. See Cordless System Operation beginning on page 39 for additional information. The Menu Commands, beginning on page 232, list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
226
Granit XP User Guide
CHAPTER
10 SERIAL PROGRAMMING COMMANDS
The serial programming commands can be used in place of the programming barcodes. Both the serial commands and the programming barcodes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming barcode in this manual.
The device must be set to an RS232 interface (see page 14). The following commands can be sent via a PC COM port using terminal emulation software.
Conventions
The following conventions are used for menu and query command descriptions:
parameter A label representing the actual value you should send as part of a command.
[option]
An optional part of a command.
{Data}
Alternatives in a command.
bold
Names of menus, menu commands, buttons, dialog boxes, and windows that appear on the screen.
Menu Command Syntax
Menu commands have the following syntax (spaces have been used for clarity only):
Prefix [:Name:] Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] [...] Storage
Prefix
Three ASCII characters: SYN M CR (ASCII 22,77,13).
:Name:
This command is only used with cordless devices. It is used to specify whether you're communicating with the base or the scanner. To send information to the scanner (with the base connected to host), use :Granit: The default factory setting for a Granit XP scanner is Granit
Granit XP User Guide
227
scanner. This setting is changed by using the BT_NAM command, which accepts alphanumeric values. If the name is not known, a wildcard (*) can be used :*
Note: Since the base stores all work group settings and transfers to them to scanner once they are linked, changes are typically done to the base and not to the scanner.
Tag
A 3 character case-insensitive field that identifies the desired menu
command group. For example, all RS232 configuration settings are
identified with a Tag of 232.
SubTag
A 3 character case-insensitive field that identifies the desired menu command within the tag group. For example, the SubTag for the RS232 baud rate is BAD.
Data
The new value for a menu setting, identified by the Tag and SubTag.
Storage
A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs the command's operation on the device's volatile menu configuration table. A period (.) performs the command's operation on the device's non-volatile menu configuration table. Use the non-volatile table only for semipermanent changes you want saved through a power cycle.
Query Commands
Several special characters can be used to query the device about its settings.
^
What is the default value for the setting(s).
>
What is the PAP sub command.
Note: When using the >, all other commands will return NAK.
?
What is the device's current value for the setting(s).
*
What is the range of possible values for the setting(s). (The device's
response uses a dash (-) to indicate a continuous range of values. A
pipe (|) separates items in a list of non-continuous values.)
:Name: Field Usage (Optional)
This command returns the query information from the scanner.
Tag Field Usage
When a query is used in place of a Tag field, the query applies to the entire set of commands available for the particular storage table indicated by the Storage field of the command. In this case, the SubTag and Data fields should not be used because they are ignored by the device.
228
Granit XP User Guide
SubTag Field Usage
When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device.
Data Field Usage
When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and SubTag fields.
Concatenation of Multiple Commands
Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be repeated for each command in the sequence. If additional commands are to be applied to the same Tag, then the new command sequence is separated with a comma (,) and only the SubTag and Data fields of the additional command are issued. If the additional command requires a different Tag field, the command is separated from previous commands by a semicolon (;).
Responses
The device responds to serial commands with one of three responses:
ACK <06> Indicates a good command which has been processed.
ENQ <15> Indicates an invalid Tag or SubTag command.
NAK <05>
Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters.
When responding, the device echoes back the command sequence with the status character inserted directly before each of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command.
Examples of Query Commands
In the following examples, a bracketed notation [ ] depicts a non-displayable response.
Example: What is the range of possible values for Codabar Coding Enable?
Enter:
cbrena*.
Response: CBRENA0-1[ACK]
Granit XP User Guide
229
This response indicates that Codabar Coding Enable (CBRENA) has a range of values from 0 to 1 (off and on).
Example: What is the default value for Codabar Coding Enable?
Enter:
cbrena^.
Response: CBRENA1[ACK]
This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.
Example: What is the device's current setting for Codabar Coding Enable?
Enter:
cbrena?.
Response: CBRENA1[ACK]
This response indicates that the device's Codabar Coding Enable (CBRENA) is set to 1, or on.
Example: What are the device's settings for all Codabar selections?
Enter:
cbr?.
Response:
CBRENA1[ACK], SSX0[ACK], CK20[ACK], CCT1[ACK], MIN2[ACK], MAX60[ACK], DFT[ACK].
This response indicates that the device's Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don't Transmit; the Check Character (CK2) is set to 0, or Not Required; concatenation (CCT) is set to 1, or Enabled; the Minimum Message Length (MIN) is set to 2 characters; the Maximum Message Length (MAX) is set to 60 characters; and the Default setting (DFT) has no value.
Trigger Commands
You can activate and deactivate the scanner with serial trigger commands. First, the scanner must be put in Manual Trigger Mode by scanning a Manual Trigger Mode barcode (page 83), or by sending a serial menu command for triggering (page 85). Once the scanner is in serial trigger mode, the trigger is activated and deactivated by sending the following commands:
Activate:
SYN T CR
Deactivate: SYN U CR
230
Granit XP User Guide
The scanner scans until a barcode has been read, until the deactivate command is sent, or until the serial time-out has been reached (see Read Time-Out on page 85 for a description, and the serial command on page 241).
Reset the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults barcode below. This resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings.
Activate Custom Defaults
Note: If using a cordless system, scanning this barcode also causes both the scanner and the base or Access Point to perform a reset and become unlinked. The scanner must be placed in its base to re-establish the link. If using an Access Point, the linking barcode must be scanned. See Cordless System Operation beginning on page 39 for additional information. The charts on the following pages list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
Granit XP User Guide
231
Menu Commands
Selection Product Default Settings Set Custom Defaults Reset the Custom Defaults Reset the Factory Defaults cordless scanners Reset the Custom Defaults cordless scanners Program the Interface Plug and Play Codes
Plug and Play Codes: RS485
Plug and Play Codes: IBM SurePos Plug and Play Codes: USB
Plug and Play Codes
Setting * Indicates default
Set Custom Defaults Save Custom Defaults Activate Custom Defaults Factory Default Settings: All Application Groups Custom Default Settings: All Application Groups
Keyboard Wedge: IBM PC AT and Compatibles with CR suffix Laptop Direct Connect with CR suffix RS232 Serial Port IBM Port 5B Interface
IBM Port 9B HHBCR-1 Interface IBM Port 17 Interface IBM Port 9B HHBCR-2 Interface USB IBM SurePos Handheld USB IBM SurePos Tabletop USB Keyboard (PC) USB Keyboard (Mac) USB Japanese Keyboard (PC) USB HID USB Serial CTS/RTS Emulation On *CTS/RTS Emulation Off ACK/NAK Mode On *ACK/NAK Mode Off *Report PID as built Report PID as Granit 1910i Report PID as Granit 1980i Verifone Ruby Terminal Gilbarco Terminal Honeywell Bioptic Aux Port Datalogic Magellan Aux Port
Serial Command # Indicates a numeric entry
MNUCDP MNUCDS DEFALT PAPDFT&
PAPDFT
PAP_AT
PAPLTD
PAP232 PAPP5B
PAP9B1 PAPP17 PAP9B2 PAPSPH PAPSPT PAP124 PAP125 TRMUSB134 PAP131 TRMUSB130 USBCTS1 USBCTS0 USBACK1 USBACK0 USBXnn0 USBXnn3 USBXnn4 PAPRBY PAPGLB PAPBIO PAPMAG
Page
11 11 12 66
67
13
14
14 14
14 15 15 15 15 16 16 16 16 16 17 17 17 17 17 17 17 18 18 18 19
232
Granit XP User Guide
Selection Program Keyboard Country
Granit XP User Guide
Setting * Indicates default
Wincor Nixdorf Terminal Wincor Nixdorf Beetle Wincor Nixdorf RS232 Mode A *U.S.A.
Albania Azeri (Cyrillic) Azeri (Latin) Belarus Belgium Bosnia Brazil Brazil (MS) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ) Denmark Dutch (Netherlands) Estonia Faroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek (319) Greek (Latin) Greek (MS)
Serial Command # Indicates a numeric entry PAPWNX PAPBTL PAPWMA KBDCTY0
KBDCTY35 KBDCTY81 KBDCTY80 KBDCTY82 KBDCTY1 KBDCTY33 KBDCTY16 KBDCTY59 KBDCTY52 KBDCTY53 KBDCTY54 KBDCTY18 KBDCTY55 KBDCTY32 KBDCTY15 KBDCTY40 KBDCTY39 KBDCTY38 KBDCTY8 KBDCTY11 KBDCTY41 KBDCTY83 KBDCTY2 KBDCTY3 KBDCTY84 KBDCTY4 KBDCTY17 KBDCTY64 KBDCTY61 KBDCTY65 KBDCTY62 KBDCTY63 KBDCTY66
Page
19 19 20 20
20 20 20 21 21 21 21 21 21 21 21 21 21 21 21 22 22 22 22 22 22 22 22 22 22 22 22 23 23 23 23 23 23
233
Selection
234
Setting * Indicates default
Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) Norway Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) SCS Serbia (Cyrillic) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation
Serial Command # Indicates a numeric entry KBDCTY60 KBDCTY12 KBDCTY50 KBDCTY19 KBDCTY75 KBDCTY73 KBDCTY56 KBDCTY5 KBDCTY28 KBDCTY78 KBDCTY79 KBDCTY14 KBDCTY42 KBDCTY43 KBDCTY44 KBDCTY45 KBDCTY34 KBDCTY74 KBDCTY86 KBDCTY9 KBDCTY20 KBDCTY57 KBDCTY58 KBDCTY13 KBDCTY25 KBDCTY26 KBDCTY67 KBDCTY68 KBDCTY21 KBDCTY37 KBDCTY36 KBDCTY22 KBDCTY49 KBDCTY48 KBDCTY31 KBDCTY10 KBDCTY51
Page
23 23 23 23 23 23 24 24 24 24 24 24 24 24 24 24 24 24 25 25 25 25 25 25 25 25 25 25 25 25 26 26 26 26 26 26 26
Granit XP User Guide
Selection
ALT Mode Keyboard Style Keyboard Conversion Control Character Output
Setting * Indicates default
Sweden Switzerland (French) Switzerland (German) Tatar Turkey F Turkey Q Ukrainian United Kingdom United Stated (Dvorak right) United States (Dvorak left) United States (Dvorak) United States (International) Uzbek (Cyrillic) * Off 3 Characters 4 Characters *Regular Caps Lock Shift Lock *Caps Lock Shift Enable (Europe) Caps Lock Shift Enable (China) Automatic Caps Lock Autocaps via Num Lock Emulate External Keyboard *Keyboard Conversion Off Convert all Characters to Upper Case Convert all Characters to Lower Case *Control Character Output Off Control Character Output On
Serial Command # Indicates a numeric entry KBDCTY23 KBDCTY29 KBDCTY6 KBDCTY85 KBDCTY27 KBDCTY24 KBDCTY76 KBDCTY7 KBDCTY89 KBDCTY88 KBDCTY87 KBDCTY30 KBDCTY77 KBDALT0 KBDALT6 KBDALT7 KBDSTY0 KBDSTY1 KBDSTY2 KBDCSE0 KBDCSE1 KBDSTY6 KBDSTY7 KBDSTY5 KBDCNV0 KBDCNV1
KBDCNV2
KBDNPE0 KBDNPE1
Page
26 26 26 26 26 27 27 27 27 27 27 27 27 28 28 28 28 28 28 28 28 29 29 29 30 30
30
30 30
Granit XP User Guide
235
Selection Keyboard Modifiers
Baud Rate
Word Length: Data Bits, Stop Bits, and Parity
RS232 Receiver Time-out
Setting * Indicates default
*Control + X Off DOS Mode Control + X Windows Mode Control + X Windows Mode Prefix/Suffix Off DOS Mode Control + X Mode On with Windows Mode Prefix/Suffix Supports ALT 3 Digit HEX Mode *Turbo Mode Off Turbo Mode On *Numeric Keypad Off Numeric Keypad On *Auto Direct Connect Off Auto Direct Connect On 300 BPS 600 BPS 1,200 BPS 2,400 BPS 4,800 BPS 9,600 BPS 19,200 BPS 38,400 BPS 57,600 BPS *115,200 BPS 7 Data, 1 Stop, Parity Even
Serial Command # Indicates a numeric entry KBDCAS0 KBDCAS1 KBDCAS2 KBDCAS3 KBDCAS4
KBDCAS5 KBDTMD0 KBDTMD1 KBDNPS0 KBDNPS1 KBDADC0 KBDADC1 232BAD0 232BAD1 232BAD2 232BAD3 232BAD4 232BAD5 232BAD6 232BAD7 232BAD8 232BAD9 232WRD3
7 Data, 1 Stop, Parity None 7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity Even 7 Data, 2 Stop, Parity None 7 Data, 2 Stop, Parity Odd 8 Data, 1 Stop, Parity Even *8 Data, 1 Stop, Parity None 8 Data, 1 Stop, Parity Odd 8 Data, 1 Stop, Parity Mark Range 0 - 300 seconds *0
232WRD0 232WRD6 232WRD4 232WRD1 232WRD7 232WRD5 232WRD2 232WRD8 232WRD14 232LPT###
Page
31 31 31 31 31
31 31 31 32 32 32 32 32 32 32 33 33 33 33 33 33 33 33
33 34 34 34 34 34 34 34 34 34
236
Granit XP User Guide
Selection RS232 Handshaking
Scanner-Bioptic Packet Mode Scanner-Bioptic ACK/NAK Mode Scanner-Bioptic ACK/NAK Timeout Cordless System Operation Link the Scanner to the charge base Replace a Linked Scanner Temporary Streaming Presentation Mode Presentation Mode in Base Connect with Bluetooth Device directly Base Power Communication Indicator Reset Scanner Base Charge Modes
Page Mode Page Pitch
Setting * Indicates default
*RTS/CTS Off Flow Control, No Timeout Two-Direction Flow Control Flow Control with Timeout RS232 Timeout (1-5100 milliseconds) *XON/XOFF Off XON/XOFF On *ACK/NAK Off ACK/NAK On *Packet Mode Off Packet Mode On *Bioptic ACK/NAK Off Bioptic ACK/NAK On ACK/NAK Timeout (1-30000 milliseconds) *5100
*Legacy Mode Compatibility Mode Override locked Scanner (Single Scanner) *10 Second Timeout 30 Second Timeout *Disabled Enabled Disabled Enabled *On Off Reset Scanner Base Charge Off *External or Interface Cable Power External Power Only *On Off *Low (1000 Hz) Medium (3250 Hz) High (4200 Hz)
Serial Command # Indicates a numeric entry 232CTS0 232CTS1 232CTS2 232CTS3 232DEL####
232XON0 232XON1 232ACK0 232ACK1 232PKT0 232PKT2 232NAK0 232NAK1 232DLK#####
LKBMOD0 LKBMOD1 BT_RPL1
TRGTPM10000 TRGTPM30000 BT_PIB0 BT_PIB1 BT_CEN0 BT_CEN1 :*:BASRED1 :*:BASRED0 RESET_ BTRCHG0 BTRCHG1 BTRCHG2 BEPPGE1 BEPPGE0 BEPPFQ1000 BEPPFQ3250 BEPPFQ4200
Page
35 35 35 35 35
36 36 36 36 37 37 37 37 37
39 40 40
43 43 44 44 68 68 47 47 49 49 49 50 50 50 50 50 50
Granit XP User Guide
237
Selection Beeper Pitch - Base Error Number of Beeps - Base Error Scanner Report Scanner Address Base Address Scanner Modes
Out-of-Range Alarm
Alarm Sound Type Scanner Power Time-Out Timer
Flexible Power Management for Granit XP
Batch Mode
Batch Mode Beep Batch Mode Storage
Setting * Indicates default
*Low/Razz (250 Hz) (min 200 Hz) Medium (3250 Hz) High (4200 Hz) (max 9000 Hz) *1 (Range 1 - 9) Scanner Report Scanner Address Base Address Charge Only Mode *Charge and Link Mode Locked Link Mode *Open Link Mode Unlink Scanner Override Locked Scanner Base Alarm Duration (Range 1 3000 sec) *0 Scanner Alarm Duration (Range 1 - 3000 sec) *0 Base Alarm Type (0-7) *0 Scanner Alarm Type (0-7) *0 0 Seconds 200 Seconds 400 Seconds 900 Seconds *3600 Seconds 7200 Seconds *Full Power (100%) Medium Power (35%) Medium Low Power (5%) Low Power (1%) Automatic Batch Mode *Batch Mode Off Inventory Batch Mode Persistent Batch Mode Off *On *Flash Storage RAM Storage
Serial Command # Indicates a numeric entry BASFQ2250 BASFQ23250 BASFQ24200 BASERR# RPTSCN BT_LDA BASLDA BASLNK0 BASLNK1 BASCON0,DNG1 BASCON1,DNG1 BT_RMV BT_RPL1 BASORD####
BT_ORD####
BASORW# BT_ORW# BT_LPT0 BT_LPT200 BT_LPT400 BT_LPT900 BT_LPT3600 BT_LPT7200 BT_TXP100 BT_TXP35 BT_TXP5 BT_TXP1 BATENA1 BATENA0 BATENA2 BATENA3 BATBEP0 BATBEP1 BATNVS1 BATNVS0
Page
51 51 51 51 51 52 52 52 53 53 53 54 54 55
55
55 55 56 56 56 56 56 56 57 57 57 57 58 58 58 58 59 59 59 59
238
Granit XP User Guide
Selection Batch Mode Quantity Quantity Codes
Batch Mode Output Order Total Records Delete Last Code Clear All Codes Transmit Records to Host Batch Mode Transmit Delay
Multiple Scanner Operation Scanner Name
Application Work Group Selections Reset the Factory Defaults: All Application Work Groups Reset the Custom Defaults: All Application Work Groups Bluetooth Connection
Setting * Indicates default
*Off On 0 *1 2 3 4 5 6 7 8 9 *FIFO LIFO Total Records Delete Last Code Clear All Codes Transmit Inventory Records *Off (No Delay) Short (250 ms) Medium (500 ms) Long (1000 ms) Multiple Scanner Operation 0001 0002 0003 Reset Scanner Name *Group 0 Group 1 Group 2 Factory Default Settings: All Work Groups Custom Default Settings: All Work Groups *Bluetooth SSP On Bluetooth SSP Off Bluetooth HID Keyboard Connect
Serial Command # Indicates a numeric entry BATQTY0 BATQTY1 BATNUM0 BATNUM1 BATNUM2 BATNUM3 BATNUM4 BATNUM5 BATNUM6 BATNUM7 BATNUM8 BATNUM9 BATLIF0 BATLIF1 BATNRC BATUND BATCLR BAT_TX BATDLY0 BATDLY250 BATDLY500 BATDLY1000 BASCON2,DNG3 BT_NAM0001 BT_NAM0002 BT_NAM0003 RESET_ BT_NAM GRPSEL0 GRPSEL1 GRPSEL2 PAPDFT&
PAPDFT
BT_SSP1 BT_SSP0 PAPBTH
Page
60 60 61 61 61 61 61 61 61 61 61 61 62 62 62 62 62 63 63 63 63 63 64 64 64 64 64 65 65 66 66 66
67
67 67 68
Granit XP User Guide
239
Selection
Virtual Keyboard Bluetooth Serial Port - PCs/ Laptops PDA's/Mobility Systems Devices Change the Scanner's Bluetooth PIN Code Auto Reconnect Mode Maximum Link Attempts Relink Time-Out Host Command Acknowledgment
Input/Output Selections Power Up Beeper
Beep on BEL Character Trigger Click Beeper - Good Read Beeper Volume - Good Read
Beeper Pitch - Good Read (Frequency)
Setting * Indicates default
Bluetooth HID Japanese Keyboard Connect Bluetooth HID Keyboard Disconnect Disable *Enable Non-Base BT Connection
BT Connection - PDA/Mobility Systems Device Bluetooth PIN Code
*Auto Reconnect On Auto Reconnect Off Maximum Link Attempts (0-100) *0 Relink Time-Out (1-100) *3 Host ACK On *Host ACK Off Host ACK Timeout (1-90) *10
Power Up Beeper Off - Scanner *Power Up Beeper On - Scanner Power Up Beeper Off - Cordless Base Power Up Beeper On - Cordless Base Beep on BEL On *Beep on BEL Off On *Off Off *On Off Low Medium *High Low (1600 Hz) (min 400 Hz)
*Medium (2700 Hz)
Serial Command # Indicates a numeric entry PAPJKB
PAPSPP
BT_DBL0 BT_DBL1 BT_TRM0;BT_DNG5
BT_TRM0;BT_DNG1
BT_PIN
BT_ACM1 BT_ACM0 BT_MLA###
BT_RLT### HSTACK1 HSTACK0 HSTATO##
BEPPWR0 BEPPWR1 BASPWR0
BASPWR1
BELBEP1 BELBEP0 BEPTRG1 BEPTRG0 BEPBEP0 BEPBEP1 BEPLVL0 BEPLVL1 BEPLVL2 BEPLVL3 BEPFQ11600
BEPFQ12700
Page
68
70
69 69 70
70
70
71 71 72
72 75 75 75
77 77 77
77
78 78 78 78 78 78 78 79 79 79 79
79
240
Granit XP User Guide
Selection
Vibrate - Good Read Vibrate Duration Beeper Pitch - Error (Frequency)
Beeper Duration - Good Read LED - Good Read Number of Beeps - Good Read Number of Beeps - Error Good Read Delay
User-Specified Good Read Delay Trigger Modes Trigger Toggle
Trigger Number
Trigger Timing Trigger Toggle Timeout Serial Trigger Mode Trigger Mode 11 Presentation Mode Triggered Presentation Mode
Setting * Indicates default
High (4200 Hz) (max 9000 Hz) Vibrate - Good Read Off *Vibrate - Good Read On Duration (100 - 2,000 ms) *100 *Razz (250 Hz) (min 200 Hz) Medium (3250 Hz) High (4200 Hz) (max 9000 Hz) *Normal Beep Short Beep Off *On (Range 1 - 9) *1 (Range 1 - 9) *1 *No Delay Short Delay (500 ms) Medium Delay (1000 ms) Long Delay (1500 ms) Range 0 - 30,000 ms *Manual Trigger - Normal Manual Trigger - Enhanced *Trigger Toggle Off Trigger Toggle - Image Capture Trigger Toggle Off - Centering 2 Quick Triggers *3 Quick Triggers 4 Quick Triggers Trigger Timing (Range 50 - 2000) *400 Trigger Toggle Timeout (Range 0 65) *5 Read Time-Out (0 - 300,000 ms) *30,000 *Disable Enable Presentation Mode Ambient Light Only *Ambient and Scanner Light
Serial Command # Indicates a numeric entry BEPFQ14200 TFBGRD0 TFBGRD1 TFBDUR####
BEPFQ2250 BEPFQ23250 BEPFQ24200 BEPBIP0 BEPBIP1 BEPLED0 BEPLED1 BEPRPT# BEPERR# DLYGRD0 DLYGRD500 DLYGRD1000 DLYGRD1500 DLYGRD##### PAPHHF PAPHHS TRGTGM0 TRGTGM1 TRGTGM3 TRGTPC2 TRGTPC3 TRGTPC4 TRGTTI####
TRGTGT##
TRGSTO####
TRGMOD0 TRGMOD1 PAPTPR PDCLED0 PDCLED1
Page
79 80 80 80
80 80 80 81 81 81 81 81 81 82 82 82 82 82 83 83 83 83 83 84 84 84 84
84
85
85 85 86 86 86
Granit XP User Guide
241
Selection Presentation LED Behavior After Decode Presentation Centering Window
Camera Selection Camera Sensors Camera Illumination
Poor Quality Codes
CodeGate Streaming Presentation Hands Free Time-Out
Setting * Indicates default
*LEDs On LEDs Off Presentation Centering On *Presentation Centering Off Left of Presentation Centering Window (*40%) Right of Presentation Centering Window (*60%) Top of Presentation Centering Window (*40%) Bottom of Presentation Centering Window (*60%) Near Camera Only Far Camera Only *Automatic Switching Alternate Switching Far Position Medium Position Near Position *All Positions *Fixed Illumination Near Camera *Far Camera Alternate Illumination Automatic Illumination Poor Quality 1D Reading On *Poor Quality 1D Reading Off *Poor Quality PDF Reading On Poor Quality PDF Reading Off Low Resolution PDF Codes On *Low Resolution PDF Codes Off *CodeGate Off CodeGate On Streaming Presentation Mode Normal Streaming Presentation Mode Enhanced Range (0 - 300,000 ms) 5000 ms
Serial Command # Indicates a numeric entry TRGPCK1 TRGPCK0 PDCWIN1 PDCWIN0 PDCLFT###
PDCRGT###
PDCTOP###
PDCBOT###
SDRSEL0 SDRSEL1 SDRSEL2 SDRSEL3 SDRVCM0 SDRVCM1 SDRVCM2 SDRVCM3 LITMOD0 LITSEL0 LITSEL1 LITMOD1 LITMOD2 DECLDI1 DECLDI0 PDFXPR10 PDFXPR0 PDFDMI1 PDFDMI0 AOSCGD0 AOSCGD1 PAPSPN
PAPSPE
TRGPTO######
Page
86 86 88 88 88
88
88
88
88 88 88 88 89 89 89 89 89 89 89 89 89 90 90 90 91 91 91 91 91 92
92
92
242
Granit XP User Guide
Selection Reread Delay
User-Specified 2D Reread Delay
Character Activation Mode
Character Deactivation Mode Illumination Lights Aimer Delay
User-Specified Aimer Delay Aimer Mode Laser Aimer-Scan Duration Single Code Centering
Setting * Indicates default
Short (500 ms) *Medium (750 ms) Long (1000 ms) Extra Long (2000 ms) Range 0 - 30,000 ms *2D Reread Delay Off Short (1000ms) Medium (2000ms) Long (3000ms) Extra Long (4000ms) *Off On Activation Character (Range 0255) *12 [DC2] Do Not End Character Activation After Good Read End Character Activation After Good Read Character Activation Timeout (Range 1 - 300,000) *30,000 ms *Off On Deactivation Character (Range 0255) *14 [DC4] *Lights On Lights Off 1 millisecond 250 milliseconds 500 milliseconds *Off (no delay) Range 0 - 4,000 ms Off *Interlaced *10 Second Scan Laser-Aimer Scan (0-65,535 ms) Single Code Centering
Serial Command # Indicates a numeric entry DLYRRD500 DLYRRD750 DLYRRD1000 DLYRRD2000 DLYRRD##### DLY2RR0 DLY2RR1000 DLY2RR2000 DLY2RR3000 DLY2RR4000 HSTCEN0 HSTCEN1 HSTACH###
HSTCGD0
HSTCGD1
HSTCDT######
HSTDEN0 HSTDEN1 HSTDCH###
SCNLED1 SCNLED0 SCNDLY1 SCNDLY250 SCNDLY500 SCNDLY0 SCNDLY#### SCNAIM0 SCNAIM2 SCNAIT10000 SCNAIT##### DECWIN1;DECTOP49;DECBOT 51;DECRGT51;DECLFT49
Page
93 93 93 93 93 93 94 94 94 94 94 94 94
94
95
95
95 95 96
96 96 96 96 97 97 97 97 97 97 97 98
Granit XP User Guide
243
Selection Centering Window
Preferred Symbology Output Sequence Editor
Require Output Sequence Good Read Tone - Output Sequences
244
Setting * Indicates default
Serial Command # Indicates a numeric entry
Centering On
DECWIN1
*Centering Off
DECWIN0
Left of Centering Window (*40%) DECLFT###
Right of Centering Window (*60%)
DECRGT###
Top of Centering Window (*40%) DECTOP###
Bottom of Centering Window (*60%)
DECBOT###
On
PRFENA1
*Off
PRFENA0
High Priority Symbology
PRFCOD##
Low Priority Symbology
PRFBLK##
Preferred Symbology Timeout (Range 100-3,000 ms) *500 ms
PRFPTO####
Preferred Symbology Default
PRFDFT
Enter Output Sequence
SEQBLK
Add Prefix to Complete Output Sequences
SEQPRE
Add Suffix to Complete Output Sequences
SEQSUF
Add Separators to Complete Output Sequences
SEQSEP
Terminate String
FF
Transmit Partial Output Sequence SEQTTS1
Add Prefix to Partial Output Sequences
SEQIPR
Add Suffix to Partial Output Sequences
SEQISU
Add Separators to Partial Output Sequences
SEQISE
Define Satisfactory Subsets
SEQSAT
Timeout for SEQSAT
SEQTIM
Timeout for Partial Output Sequences
TRGSTO
*Discard Partial Output Sequence SEQTTS0
Default Output Sequence
SEQDFT
Required
SEQ_EN2
On/Not Required
SEQ_EN1
*Off
SEQ_EN0
Good Read Beep - Each Code in Sequence
BEPSIN0
Page
99 99 100 100
99 100
100 100 101 101 101
101 103 103
103
103
103 103 103
103
103
103 103 103
108 109 109 109 109 110
Granit XP User Guide
Selection
Multiple Symbols No Read Video Reverse
Working Orientation
Prefix/Suffix Selections Add CR Suffix to All Symbologies Prefix
Suffix
Function Code Transmit Intercharacter Delay User Specified Intercharacter Delay Interfunction Delay Intermessage Delay
Setting * Indicates default
*Good Read Click - Each Code in Sequence Good Read Beep - Partial Sequence Output *Error Tone - Partial Sequence Output On *Off On *Off Video Reverse Only Video Reverse and Standard Barcodes *Video Reverse Off *Upright Vertical, Bottom to Top (Rotate CCW 90°) Upside Down Vertical, Top to Bottom (Rotate CW 90°)
Serial Command # Indicates a numeric entry BEPSIN1
BEPISE0
BEPISE1
SHOTGN1 SHOTGN0 SHWNRD1 SHWNRD0 VIDREV1 VIDREV2
VIDREV0 ROTATN0 ROTATN1
ROTATN2 ROTATN3
Add Prefix Clear One Prefix Clear All Prefixes Add Suffix Clear One Suffix Clear All Suffixes *Enable Disable Range 0 - 5000 (5ms increments) Delay Length 0 - 5000 (5ms increments) Character to Trigger Delay Range 0 - 5000 (5ms increments) Range 0 - 5000 (5ms increments)
VSUFCR PREBK2## PRECL2 PRECA2 SUFBK2## SUFCL2 SUFCA2 RMVFNC0 RMVFNC1 DLYCHR#### DLYCRX####
DLY_XX## DLYFNC#### DLYMSG####
Page
110
110
110
110 110 111 111 111 111
112 112 112
112 112
115 115 115 115 115 115 115 116 116 116 117
117 117 118
Granit XP User Guide
245
Selection Data Formatter Selections Data Format Editor
Data Formatter
Data Format Non-Match Error Tone Primary/Alternate Data Formats
Single Scan Data Format Change
Symbologies All Symbologies Codabar Codabar Start/Stop Char. Codabar Check Char.
Setting * Indicates default
Serial Command # Indicates a numeric entry
*Default Data Format (None) Show Data Format Settings Enter Data Format Clear One Data Format Clear All Data Formats Data Formatter Off *Data Formatter On, Not Required, Keep Prefix/Suffix Data Format Required, Keep Prefix/Suffix Data Formatter On, Not Required, Drop Prefix/Suffix Data Format Required, Drop Prefix/Suffix *Data Format Non-Match Error Tone On Data Format Non-Match Error Tone Off Primary Data Format Data Format 1 Data Format 2 Data Format 3 Single Scan-Primary Data Format Single Scan-Data Format 1 Single Scan-Data Format 2 Single Scan-Data Format 3
DFMDF3 DFMBK3? DFMBK3## DFMCL3 DFMCA3 DFM_EN0 DFM_EN1
DFM_EN2
DFM_EN3
DFM_EN4
DFMDEC0
DFMDEC1
ALTFNM0 ALTFNM1 ALTFNM2 ALTFNM3 VSAF_0 VSAF_1 VSAF_2 VSAF_3
All Symbologies Off Default All Codabar Settings Off *On *Don't Transmit Transmit *No Check Char. Validate, But Don't Transmit Validate, and Transmit
ALLENA0 CBRDFT CBRENA0 CBRENA1 CBRSSX0 CBRSSX1 CBRCK20 CBRCK21 CBRCK22
Page
120 120 121 121 121 135 136
136
136
136
136
137
137 137 137 137 137 138 138 138
140 140 140 140 141 141 141 141 141
246
Granit XP User Guide
Selection
Setting * Indicates default
Codabar Concatenation Codabar Message Length Code 39 Code 39 Start/Stop Char. Code 39 Check Char. Code 39 Message Length Code 39 Append Code 32 Pharmaceutical (PARAF) Code 39 Full ASCII Interleaved 2 of 5
Interleaved 2 of 5 Check Digit Interleaved 2 of 5 Message Length
NEC 2 of 5
*Off On Require Minimum (2 - 60) *4 Maximum (2 - 60) *60 Default All Code 39 Settings Off *On *Don't Transmit Transmit *No Check Char. Validate, But Don't Transmit Validate, and Transmit Minimum (0 - 48) *0 Maximum (0 - 48) *48 *Off On *Off On *Off On Code 39 Code Page Default All Interleaved 2 of 5 Settings Off *On *No Check Digit Validate, But Don't Transmit Validate and Transmit Minimum (2 - 80) *6 Maximum (2 - 80) *80 *FEBRABAN Decode Off FEBRABAN Decode On Default All NEC 2 of 5 Settings Off *On
Serial Command # Indicates a numeric entry CBRCCT0 CBRCCT1 CBRCCT2 CBRMIN## CBRMAX## C39DFT C39ENA0 C39ENA1 C39SSX0 C39SSX1 C39CK20 C39CK21 C39CK22 C39MIN## C39MAX## C39APP0 C39APP1 C39B320 C39B321 C39ASC0 C39ASC1 C39DCP I25DFT
I25ENA0 I25ENA1 I25CK20 I25CK21 I25CK22 I25MIN## I25MAX## I25PAY0 I25PAY1 N25DFT N25ENA0 N25ENA1
Page
142 142 142 142 142 143 143 143 143 143 143 143 143 144 144 144 144 145 145 145 145 145 146
146 146 146 146 146 147 147 147 147 148 148 148
Granit XP User Guide
247
Selection
Setting * Indicates default
NEC 2 of 5 Check Digit
NEC 2 of 5 Message Length Code 93
Code 93 Message Length Code 93 Append Code 93 Code Page Straight 2 of 5 Industrial
Straight 2 of 5 Industrial Message Length Straight 2 of 5 IATA Straight 2 of 5 IATA Straight 2 of 5 IATA Redundancy Straight 2 of 5 IATA Message Length Matrix 2 of 5
Matrix 2 of 5 Message Length Code 11
Code 11 Check Digits Required
*No Check Digit Validate, But Don't Transmit Validate and Transmit Minimum (2 - 80) *4 Maximum (2 - 80) *80 Default All Code 93 Settings Off *On Minimum (0 - 80) *0 Maximum (0 - 80) *80 On *Off Code 93 Code Page Default All Straight 2 of 5 Industrial Settings *Off On Minimum (1 - 48) *4 Maximum (1 - 48) *48 Default All Straight 2 of 5 IATA Settings *Off On Range (0 - 10) *0 Minimum (1 - 48) *4 Maximum (1 - 48) *48 Default All Matrix 2 of 5 Settings *Off On Minimum (1 - 80) *4 Maximum (1 - 80) *80 Default All Code 11 Settings *Off On 1 Check Digit *2 Check Digits
Serial Command # Indicates a numeric entry N25CK20 N25CK21 N25CK22 N25MIN## N25MAX## C93DFT C93ENA0 C93ENA1 C93MIN## C93MAX## C93APP1 C93APP0 C93DCP R25DFT
R25ENA0 R25ENA1 R25MIN## R25MAX## A25DFT
A25ENA0 A25ENA1 A25VOT## A25MIN## A25MAX## X25DFT
X25ENA0 X25ENA1 X25MIN## X25MAX## C11DFT C11ENA0 C11ENA1 C11CK20 C11CK21
Page
148 148 148 149 149 149 149 149 149 149 150 150 150 151
151 151 151 151 152
152 152 152 152 152 153
153 153 153 153 154 154 154 154 154
248
Granit XP User Guide
Selection Code 11 Message Length Code 128
ISBT Concatenation Code 128 Redundancy Code 128 Message Length Code 128 Append Code 128 Code Page GS1-128
GS1-128 Message Length Telepen
Telepen Output Telepen Message Length UPC-A
UPC-A Check Digit UPC-A Number System UPC-A 2 Digit Addenda UPC-A 5 Digit Addenda
Setting * Indicates default
Minimum (1 - 80) *4 Maximum (1 - 80) *80 Default All Code 128 Settings Off *On *Off On Range (0 - 10) *0 Minimum (0 - 80) *0 Maximum (0 - 80) *80 On *Off Code 128 Code Page (*2) Default All GS1-128 Settings *On Off Minimum (1 - 80) *1 Maximum (0 - 80) *80 Default All Telepen Settings *Off On *AIM Telepen Output Original Telepen Output Minimum (1 - 60) *1 Maximum (1 - 60) *60 Default All UPC-A Settings Off *On Off *On Off *On *Off On *Off On
Serial Command # Indicates a numeric entry C11MIN## C11MAX## 128DFT 128ENA0 128ENA1 ISBENA0 ISBENA1 128VOT## 128MIN## 128MAX## 128APP1 128APP0 128DCP## GS1DFT GS1ENA1 GS1ENA0 GS1MIN## GS1MAX## TELDFT TELENA0 TELENA1 TELOLD0 TELOLD1 TELMIN## TELMAX## UPADFT UPBENA0 UPBENA1 UPACKX0 UPACKX1 UPANSX0 UPANSX1 UPAAD20 UPAAD21 UPAAD50 UPAAD51
Page
154 154 155 155 155 155 155 155 156 156 156 156 156 157 157 157 157 157 158 158 158 158 158 158 158 159 159 159 159 159 160 160 160 160 160 160
Granit XP User Guide
249
Selection UPC-A Addenda Required Addenda Timeout UPC-A Addenda Separator UPC-A/EAN-13 with Extended Coupon Code
Addenda Timeout Coupon GS1 DataBar Output UPC-E0
UPC-E0 Expand UPC-E0 Addenda Required Addenda Timeout UPC-E0 Addenda Separator UPC-E0 Check Digit UPC-E0 Leading Zero UPC-E0 Addenda
UPC-E1 EAN/JAN-13
Convert UPC-A to EAN-13
Setting * Indicates default
*Not Required Required Range (0 - 500) *120 Off *On *Off Allow Concatenation Require Concatenation Range (0 - 500) *120 *GS1 Output Off GS1 Output On Default All UPC-E Settings Off *On *Off On Required *Not Required Range (0 - 500) *120 *On Off Off *On Off *On 2 Digit Addenda On *2 Digit Addenda Off 5 Digit Addenda On *5 Digit Addenda Off *Off On Default All EAN/JAN Settings Off *On UPC-A Converted to EAN-13 *Do not Convert UPC-A
Serial Command # Indicates a numeric entry UPAARQ0 UPAARQ1 DLYADD##### UPAADS0 UPAADS1 CPNENA0 CPNENA1 CPNENA2 DLYADD##### CPNGS10 CPNGS11 UPEDFT UPEEN00 UPEEN01 UPEEXP0 UPEEXP1 UPEARQ1 UPEARQ0 DLYADD##### UPEADS1 UPEADS0 UPECKX0 UPECKX1 UPENSX0 UPENSX1 UPEAD21 UPEAD20 UPEAD51 UPEAD50 UPEEN10 UPEEN11 E13DFT E13ENA0 E13ENA1 UPAENA0 UPAENA1
Page
160 160 161 161 161 161 161 161 162 162 162 163 163 163 163 163 163 163 164 164 164 164 164 165 165 165 165 165 165 165 165 166 166 166 166 166
250
Granit XP User Guide
Selection EAN/JAN-13 Check Digit
EAN/JAN-13 Addenda
EAN/JAN-13 Addenda Required
EAN-13 Beginning with 290 Addenda Required EAN-13 Beginning with 378/379 Addenda Required
EAN-13 Beginning with 414/419 Addenda Required
EAN-13 Beginning with 434/439 Addenda Required
EAN-13 Beginning with 977 Addenda Required EAN-13 Beginning with 978 Addenda Required EAN-13 Beginning with 979 Addenda Required Addenda Timeout EAN/JAN-13 Addenda Separator ISBN Translate
EAN/JAN-8
Setting * Indicates default
Off *On 2 Digit Addenda On *2 Digit Addenda Off 5 Digit Addenda On *5 Digit Addenda Off *Not Required Required *Don't Require 5 Digit Addenda Require 5 Digit Addenda *Don't Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda *Don't Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda *Don't Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda *Don't Require 2 Digit Addenda Require 2 Digit Addenda *Don't Require 5 Digit Addenda Require 5 Digit Addenda *Don't Require 5 Digit Addenda Require 5 Digit Addenda Range (0 - 500) *120 Off *On *Off On Default All EAN/JAN-8 Settings Off *On
Serial Command # Indicates a numeric entry E13CKX0 E13CKX1 E13AD21 E13AD20 E13AD51 E13AD50 E13ARQ0 E13ARQ1 ARQ2900 ARQ2901 ARQ3780 ARQ3781 ARQ3782 ARQ3783 ARQ4140 ARQ4141 ARQ4142 ARQ4143 ARQ4340 ARQ4341 ARQ4342 ARQ4343 ARQ9770 ARQ9771 ARQ9780 ARQ9781 ARQ9790 ARQ9791 DLYADD##### E13ADS0 E13ADS1 E13ISB0 E13ISB1 EA8DFT EA8ENA0 EA8ENA1
Page
167 167 167 167 167 167 167 167 168 168 168 168 168 168 169 169 169 169 170 170 170 170 170 170 171 171 171 171 172 172 172 173 173 173 173 173
Granit XP User Guide
251
Selection EAN/JAN-8 Check Digit EAN/JAN-8 Addenda
EAN/JAN-8 Addenda Required Addenda Timeout EAN/JAN-8 Addenda Separator MSI MSI Check Character
MSI Message Length GS1 DataBar Omnidirectional
GS1 DataBar Limited
Setting * Indicates default
Off *On *2 Digit Addenda Off 2 Digit Addenda On *5 Digit Addenda Off 5 Digit Addenda On *Not Required Required Range (0 - 500) *120 Off *On Default All MSI Settings *Off On *Validate Type 10, but Don't Transmit Validate Type 10 and Transmit Validate 2 Type 10 Chars, but Don't Transmit Validate 2 Type 10 Chars and Transmit Validate Type 11 then Type 10 Char, but Don't Transmit Validate Type 11 then Type 10 Char and Transmit Disable MSI Check Characters Minimum (4 - 48) *4 Maximum (4 - 48) *48 Default All GS1 DataBar Omnidirectional Settings Off *On Default All GS1 DataBar Limited Settings Off *On
Serial Command # Indicates a numeric entry EA8CKX0 EA8CKX1 EA8AD20 EA8AD21 EA8AD50 EA8AD51 EA8ARQ0 EA8ARQ1 DLYADD##### EA8ADS0 EA8ADS1 MSIDFT MSIENA0 MSIENA1 MSICHK0
MSICHK1
MSICHK2
MSICHK3
MSICHK4
MSICHK5
MSICHK6 MSIMIN## MSIMAX## RSSDFT
RSSENA0 RSSENA1 RSLDFT
RSLENA0 RSLENA1
Page
173 173 174 174 174 174 174 174 174 175 175 175 175 175 176
176
176
176
176
176
176 177 177 177
177 177 178
178 178
252
Granit XP User Guide
Selection GS1 DataBar Expanded
GS1 DataBar Expanded Msg. Length Trioptic Code Codablock A
Codablock A Msg. Length Codablock F
Codablock F Msg. Length Label Code PDF417
PDF417 Msg. Length MacroPDF417 MicroPDF417
MicroPDF417 Msg. Length GS1 Composite Codes UPC/EAN Version
Setting * Indicates default
Default All GS1 DataBar Expanded Settings Off *On Minimum (4 - 74) *4 Maximum (4 - 74) *74 *Off On Default All Codablock A Settings *Off On Minimum (1 - 600) *1 Maximum (1 - 600) *600 Default All Codablock F Settings *Off On Minimum (1 - 2048) *1 Maximum (1 - 2048) *2048 On *Off Default All PDF417 Settings *On Off Minimum (1-2750) *1 Maximum (1-2750) *2750 *On Off Default All Micro PDF417 Settings On *Off Minimum (1-366) *1 Maximum (1-366) *366 On *Off On *Off
Serial Command # Indicates a numeric entry RSEDFT
RSEENA0 RSEENA1 RSEMIN## RSEMAX## TRIENA0 TRIENA1 CBADFT CBAENA0 CBAENA1 CBAMIN### CBAMAX### CBFDFT CBFENA0 CBFENA1 CBFMIN#### CBFMAX#### LBLENA1 LBLENA0 PDFDFT PDFENA1 PDFENA0 PDFMIN#### PDFMAX#### PDFMAC1 PDFMAC0 MPDDFT
MPDENA1 MPDENA0 MPDMIN### MPDMAX### COMENA1 COMENA0 COMUPC1 COMUPC0
Page
178
178 178 178 178 179 179 179 179 179 180 180 180 180 180 180 180 181 181 181 181 181 182 182 182 182 182
182 182 183 183 183 183 184 184
Granit XP User Guide
253
Selection GS1 Composite Codes Msg. Length GS1 Emulation
TCIF Linked Code 39 QR Code QR Code Msg. Length QR Code Append
QR Code Page QR Code with Web Link DotCode Poor Quality DotCodes DotCode Msg. Length Digimarc Barcode
254
Setting * Indicates default
Minimum (1-2435) *1 Maximum (1-2435) *2435 GS1-128 Emulation GS1 DataBar Emulation GS1 Code Expansion Off EAN8 to EAN13 Conversion *GS1 Emulation Off On *Off Default All QR Code Settings *On Off Minimum (1-7089) *1 Maximum (1-7089) *7089 *One Scan Swipe Point & Shoot Off QR Code Page (*3) *On Off Default All DotCode Settings On *Off Poor Quality DotCodes On *Poor Quality DotCodes Off Minimum (1- 2400) *1 Maximum (1- 2400) *2400 Decoder Attempts (0-10) *3 *Off On Uses ID Decoder then Both Decoders Uses Digimarc Decoder then Both Decoders Uses ID Decoder then Alternates Decoders Uses Digimarc Decoder then Alternates Decoders
Serial Command # Indicates a numeric entry COMMIN#### COMMAX#### EANEMU1 EANEMU2 EANEMU3 EANEMU4 EANEMU0 T39ENA1 T39ENA0 QRCDFT QRCENA1 QRCENA0 QRCMIN#### QRCMAX#### QRCAPP1 QRCAPP2 QRCAPP3 QRCAPP0 QRCDCP## QRCWEB0 QRCWEB1 DOTDFT DOTENA1 DOTENA0 DOTEXS1 DOTEXS0 DOTMIN#### DOTMAX#### DIGSTR## DIGENA0 DIGENA1 DIGENA2
DIGENA3
DIGENA4
DIGENA5
Page
184 184 184 183 185 185 185 185 185 186 186 186 186 186 186 186 186 186 187 188 188 188 188 188 188 188 189 189 189 189 189 189
189
189
189
Granit XP User Guide
Selection Data Matrix
Direct Part Marking (DPM) Decoding
Data Matrix Msg. Length Data Matrix Code Page MaxiCode
MaxiCode Msg. Length Aztec Code
Aztec Code Msg. Length Aztec Append Aztec Code Page Chinese Sensible (Han Xin) Code
Chinese Sensible (Han Xin) Code Msg. Length Postal Codes - 2D 2D Postal Codes
Setting * Indicates default
Default All Data Matrix Settings *On Off Dotpeen DPM Decoding *Disable DPM Decoding Reflective (Etched) DPM Decoding Minimum (1-3116) *1 Maximum (1-3116) *3116 Data Matrix Code Page (*51) Default All MaxiCode Settings On *Off Minimum (1-150) *1 Maximum (1-150) *150 Default All Aztec Code Settings *On Off Minimum (1-3832) *1 Maximum (1-3832) *3832 *On Off Aztec Code Page (*51) Default All Han Xin Code Settings On *Off Minimum (1-7833) *1 Maximum (1-7833) *7833
Serial Command # Indicates a numeric entry IDMDFT IDMENA1 IDMENA0 DPMENA1 DPMENA0 DPMENA2
IDMMIN#### IDMMAX#### IDMDCP## MAXDFT MAXENA1 MAXENA0 MAXMIN### MAXMAX### AZTDFT AZTENA1 AZTENA0 AZTMIN#### AZTMAX#### AZTAPP1 AZTAPP0 AZTDCP## HX_DFT HX_ENA1 HX_ENA0 HX_MIN#### HX_MAX####
*Off
POSTAL0
Page
189 189 189 191 191 191
191 191 191 192 192 192 192 192 193 193 193 193 193 193 193 194 194 194 194 195 195
195
Granit XP User Guide
255
Selection Single 2D Postal Codes
Combination 2D Postal Codes
Setting * Indicates default
Australian Post On
British Post On
Canadian Post On Intelligent Mail Barcode On
Japanese Post On
KIX Post On Planet Code On
Postal-4i On
Postnet On Postnet with B and B' Fields On
InfoMail On
InfoMail and British Post On
Intelligent Mail Barcode and Postnet with B and B' Fields On
Postnet and Postal-4i On Postnet and Intelligent Mail Barcode On Postal-4i and Intelligent Mail Barcode On Postal-4i and Postnet with B and B' Fields On Planet and Postnet On
Planet and Postnet with B and B' Fields On
Planet and Postal-4i On
Planet and Intelligent Mail Barcode On
Planet, Postnet, and Postal-4i On Planet, Postnet, and Intelligent Mail Barcode On Planet, Postal-4i, and Intelligent Mail Barcode On Postnet, Postal-4i, and Intelligent Mail Barcode On Planet, Postal-4i, and Postnet with B and B' Fields On Planet, Intelligent Mail Barcode, and Postnet with B and B' Fields On
Postal-4i, Intelligent Mail Barcode, and Postnet with B and B' Fields On
Serial Command # Indicates a numeric entry POSTAL1 POSTAL7 POSTAL30 POSTAL10 POSTAL3 POSTAL4 POSTAL5 POSTAL9 POSTAL6 POSTAL11 POSTAL2 POSTAL8 POSTAL20
POSTAL14 POSTAL16
POSTAL17
POSTAL19
POSTAL12 POSTAL18
POSTAL13 POSTAL15
POSTAL21 POSTAL22
POSTAL23
POSTAL24
POSTAL25
POSTAL26
POSTAL27
Page
195 195 195 195 196 196 196 196 196 196 196 196 196
197 197
197
197
197 197
197 197
197 197
198
198
198
198
198
256
Granit XP User Guide
Selection
Planet Code Check Digit Postnet Check Digit Australian Post Interpretation
Postal Codes - Linear China Post (Hong Kong 2 of 5)
China Post (Hong Kong 2 of 5) Msg. Length Korea Post
Korea Post Msg. Length Korea Post Check Digit Imaging Default Commands Image Snap
Setting * Indicates default
Planet, Postal-4i, Intelligent Mail Barcode, and Postnet On Planet, Postal-4i, Intelligent Mail Barcode, and Postnet with B and B' Fields On Transmit *Don't Transmit Transmit *Don't Transmit *Bar Output Numeric N Table Alphanumeric C Table Combination C and N Tables
Serial Command # Indicates a numeric entry POSTAL28
POSTAL29
PLNCKX1 PLNCKX0 NETCKX1 NETCKX0 AUSINT0 AUSINT1 AUSINT2 AUSINT3
Default All China Post (Hong Kong 2 of 5) Settings *Off On Minimum (2 - 80) *4 Maximum (2 - 80) *80 Default All Korea Post Settings *Off On Minimum (2 - 80) *4 Maximum (2 - 80) *48 Transmit Check Digit *Don't Transmit Check Digit
CPCDFT
CPCENA0 CPCENA1 CPCMIN## CPCMAX## KPCDFT KPCENA0 KPCENA1 KPCMIN## KPCMAX## KPCCHK1 KPCCHK0
Default all Imaging Commands Imaging Style - Decoding *Imaging Style - Photo Imaging Style - Manual Beeper On *Beeper Off *Wait for Trigger Off Wait for Trigger On *LED State - Off LED State - On
IMGDFT SNPSTY0 SNPSTY1 SNPSTY2 SNPBEP1 SNPBEP0 SNPTRG0 SNPTRG1 SNPLED0 SNPLED1
Page
198
198
198 199 199 199 199 199 199 200
200
200 200 200 200 201 201 201 201 201 201 201
203 204 204 204 204 204 205 205 205 205
Granit XP User Guide
257
Selection Image Ship
258
Setting * Indicates default
Exposure (1-7874 microseconds) *7874 *Gain - None Gain - Medium Gain - Heavy Gain - Maximum Target White Value (0-255) *125 Delta for Acceptance (0-255) *25 Update Tries (0-10) *6 Target Set Point Percentage (199) *50 *Infinity Filter - Off Infinity Filter - On *Compensation Off Compensation On *Pixel Depth - 8 bits/pixel (grayscale) Pixel Depth - 1 bit/pixel (B&W) *Don't Sharpen Edges Sharpen Edges (0-23) *File Format - JPEG File Format - KIM File Format - TIFF binary File Format - TIFF binary group 4, compressed File Format - TIFF grayscale File Format - Uncompressed binary File Format - Uncompressed grayscale File Format - BMP File Format - BMP Uncompressed raw image *Histogram Stretch Off Histogram Stretch On *Noise Reduction Off Noise Reduction On Invert Image around X axis Invert Image around Y axis *Rotate Image none
Serial Command # Indicates a numeric entry SNPEXP
SNPGAN1 SNPGAN2 SNPGAN4 SNPGAN8 SNPWHT### SNPDEL### SNPTRY## SNPPCT##
IMGINF0 IMGINF1 IMGCOR0 IMGCOR1 IMGBPP8
IMGBPP1 IMGEDG0 IMGEDG## IMGFMT6 IMGFMT0 IMGFMT1 IMGFMT2
IMGFMT3 IMGFMT4
IMGFMT5
IMGFMT8 IMGMT15
IMGHIS0 IMGHIS1 IMGFSP0 IMGFSP1 IMGNVX1 IMGNVY1 IMGROT0
Page
205
206 206 206 206 206 206 207 207
208 208 208 208 208
208 209 209 209 209 209 209
209 209
209
209 209
210 210 211 211 210 210 211
Granit XP User Guide
Selection
Setting * Indicates default
Rotate Image 90° right
Rotate Image 180° right
Rotate Image 90° left
JPEG Image Quality (0-100) *50
*Gamma Correction Off
Gamma Correction On (0-1000)
Image Crop - Left (0-843) *0
Image Crop - Right (0-843) *843
Image Crop - Top (0-639) *0
Image Crop - Bottom (0-639) *639
Image Crop - Margin (1-238) *0
Protocol - None (raw)
Protocol - None (default USB)
Protocol - Hmodem Compressed (default RS232)
Protocol - Hmodem
*Ship Every Pixel
Ship Every 2nd Pixel
Ship Every 3rd Pixel
*Document Image Filter Off
Document Image Filter On (0255)
*Don't Ship Histogram
Ship Histogram
Image Size Compatibility
Force VGA Resolution
*Native Resolution
Intelligent Signature Capture
Optimize On
Utilities
*Optimize Off
Add Code I.D. Prefix to All Symbologies (Temporary)
Show Software Revision
Test Menu
On
*Off
Serial Command # Indicates a numeric entry IMGROT1 IMGROT2 IMGROT3 IMGJQF### IMGGAM0 IMGGAM### IMGWNL### IMGWNR### IMGWNT### IMGWNB###
IMGMAR### IMGXFR0 IMGXFR2 IMGXFR3
IMGXFR4 IMGSUB1 IMGSUB2 IMGSUB3 IMGUSH0 IMGUSH###
IMGHST0 IMGHST1 IMGVGA1 IMGVGA0 DECBND1 DECBND0
PRECA2,BK2995C80! REVINF TSTMNU1 TSTMNU0
Page
211 211 211 212 212 212 212 212 212 213
213 213 213 213
213 214 214 214 214 214
215 215 215 216 216 216
223 223 224 224
Granit XP User Guide
259
Selection Application Plug-Ins (Apps)
Reset the Factory Defaults
Setting * Indicates default
*Decoding Apps On Decoding Apps Off *Formatting Apps On Formatting Apps Off List Apps Remove Custom Defaults Activate Defaults
Serial Command # Indicates a numeric entry
PLGDCE1 PLGDCE0 PLGFOE1 PLGFOE0 PLGINF DEFOVR DEFALT
Page
224 224 224 224 224 226 226
260
Granit XP User Guide
CHAPTER
11 PRODUCT SPECIFICATIONS
Granit XP 1990i SR, XR, XLR Corded Scanner Product Specifications
Parameter Mechanical Height Length Width Weight Electrical Voltage Requirements Current Draw
Illumination LED: Peak Wavelength
Aiming: Peak Wavelength Laser
Environmental Temperature Ranges: Operating
Storage Humidity Mechanical Drop
Specification
7.5 inches (192mm) 3.9 inches (100mm) 2.9 inches (76mm) 11.2 ounces (320g)
4.4 to 5.5 VDC at input connector ScanningStandby 500mA @ 5VDC, 2.5W
625nm (red LED) IEC 62471: "Exempt Risk Group"
655nm class1 laser product (SR scanner) 655nm class 2 laser product (XR scanner) complies IEC 60825 Ed3
-22°F to 122°F (-30°C to 50°C) -40°F to 158°F (-40°C to 70°C) -40°F to 158°F (-40°C to 70°C) 0 to 95% non-condensing 2 m (6.5 ft): 50 drops from -30°C to 50°C (-22°F to 122°F), uncontrolled RH 2.4 m (8 ft): 20 drops at 25°C (77°F), 55% RH 3 m (10 ft): MIL-STD-810G, 25°C (77°F), 55% RH
Granit XP User Guide
261
Parameter (Continued) ESD Tolerance
Image Image Size Scan Performance Skew Angle Pitch Angle
1D barcode 2D barcode Motion Tolerance
Symbol Contrast Field of View XP SR XP XR
Specification Up to ±20kV direct air Up to 8 kV indirect coupling plane
1280 x 800 pixels
+65°
1D code: +65° 2D code: +45° Up to 4.5 m/s (157 in/s) for 13 mil UPC at optimal focus 20% or greater (Grade A)
48°H 30°V Near 48°H 30°V Far 19°H 11.9°V
Granit XP 1991i SR, XR, XLR Cordless Scanner Product Specifications
262
Parameter Mechanical Height Length Width Weight Electrical Current Draw
Illumination LED: Peak Wavelength
Aiming: Peak Wavelength Laser
Battery Lithium Ion
Number of Scans
Expected Hours of Operation
Specification
7.5 inches (192mm) 3.9 inches (100mm) 2.9 inches (76mm) 14.2 ounces (405g)
Operating Power (Charging) 500mA @ 5VDC, 2.5W
625nm (red LED) IEC 62471: "Exempt Risk Group"
655nm class1 laser product (SR scanner) 655nm class 2 laser product (XR scanner) complies IEC 60825 Ed3
2450 mAHr minimum SR, XR: Up to 50,000 per charge XLR: Up to 46,800 per charge SR, XR: 14 XLR: 13
Granit XP User Guide
Parameter (Continued) Expected Charge Time
Radio Frequency
Range Environmental Temperature Ranges: Operating Charging Storage with battery*
Specification 4.5 hours + 0.5 hours
2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v 4.2 33 ft. (10 m) typical
-4°F to +122°F (-20°C to 50°C) 32°F to 113°F (0°C to 45°C) -4°F to +95°F (-20°C to 35°C) for storage up to 90 days -4°F to +68°F (-20°C to 20°C) for storage up to 365 days
Storage without battery Humidity Mechanical Drop
ESD Sensitivity
Image Image Size Scan Performance Skew Angle Pitch Angle
1D barcode 2D barcode Motion Tolerance
Symbol Contrast Field of View XP SR XP XR
-40°F to +158°F (-40°C to 70°C) Up to 95% non-condensing 2 m (6.5 ft): 50 drops from -30°C to 50°C (-22°F to 122°F), uncontrolled RH 2.4 m (8 ft): 20 drops at 25°C (77°F), 55% RH 3 m (10 ft): MIL-STD-810G, 25°C (77°F), 55% RH Up to ±20kV direct air Up to ±8 kV indirect coupling
1280 x 800 pixels
+65°
1D barcodes: +65° 2D barcodes: +45° Up to 4.5 m/s (157 in/s) for 13 mil UPC at optimal focus 20% or greater (Grade A)
48°H 30°V Near 48°H 30°V Far 19°H 11.9°V
*Storage outside of this temperature range could be detrimental to battery life.
Granit XP User Guide
263
CCB22-100BT-03N/COB22 Charge Base Product Specifications
Parameter Mechanical Height Length Width Weight
CCB22 COB22 Electrical Voltage: Current Draw: Host Terminal Port Aux Power Port Charge Time Radio Frequency
Range Data Rate Environmental Temperature Ranges: Operating Storage Humidity Mechanical Drop
Vibration ESD Sensitivity
Specification
2.3 inches (60 mm) 9.6 inches (245 mm) 4.0 inches (102 mm)
10.4 oz (295g) 10.2 oz (290g)
4.0 to 5.5 VDC
500mA 1A 5 hours
2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1 330 ft. (100 m) typical Up to 1 MBps
-4° F to +122° F (-20° C to +50° C) -40° F to +158° F (-40° C to +70° C) Up to 95% non-condensing Operational after 50 drops from 3.28 feet (1 m) to concrete 5G Peak from 22Hz to 300Hz Up to ±20kV direct air Up to ±8 kV indirect coupling plane
264
Granit XP User Guide
Depth of Field Charts
Granit XP SR Performance
Focus
3 mil Code 39
mm
in.
5 mil Code 39
mm
in.
10mil Code 39
mm
in.
13 mil UPC
mm
in.
15 mil C128
mm
in.
20 mil Code 39
mm
in.
5 mil PDF147
mm
in.
6.7 mil PDF417
mm
in.
7.5 mil DM
mm
in.
10 mil Data Matrix mm
in.
15 mil QR Code
mm
in.
20 mil QR Code
mm
in.
Typical Spec 39
1.53 20
0.78 0 0 0 0 0 0 0 0
35 1.37
20 0.78
50 1.96
30 1.18
0 0 33 1.3
104 4.09 220 8.66 490 19.29 504 19.84 628 24.72 837 32.95 146 5.74 209 8.22 156 6.14 220 8.66 352 13.85 475 18.7
Guaranteed Spec
65
49
91
2.55
1.92
3.58
200
26
197
7.87
1.02
7.75
490
10
451
19.29
0.39
17.75
504
10
464
19.84
0.39
18.26
628
10
564
24.72
0.39
22.20
837
10
700
32.95
0.39
27.55
111
42
137
4.37
1.65
5.39
189
26
194
7.44
1.02
7.63
106
65
142
4.17
2.55
5.59
190
41
188
7.48
1.61
7.40
352
10
315
13.85
0.39
12.40
442
0
447
17.4
0
447
42 1.65 171 6.73 441 17.36 454 17.87 554 21.81 690 27.16
95 3.74 168 6.61
77 3.03 147 5.78 305 12.00 17.6 17.6
Granit XP User Guide
265
Granit XP XR Performance
Focus
3 mil Code 39
mm
in.
5 mil Code 39
mm
in.
10mil Code 39
mm
in.
10.4 mil C128
mm
in.
13 mil UPCA
mm
in.
15 mil C128
mm
in.
20 mil Code 39
mm
in.
20 mil QR Code
mm
in.
22 mil QR Code
mm
in.
5 mil PDF147
mm
in.
6.7 mil PDF417
mm
in.
7.5 mil DM
mm
in.
10 mil Data Matrix mm
in.
15 mil QR Code
mm
in.
55 mil C39
mm
in.
70 mil C128
mm
in.
100 Mil C39
mm
in.
100 mil C39 Retro mm
in.
100 mil DM
mm
in.
Typical Spec 39
1.53 20
0.78 0 0 3
0.1 0 0 0 0 0 0 0 0 0 0
35 1.37
20 0.78
50 1.96
30 1.18
0 0 86 3.38 136 5.4 280 11.02 172 6.77 156 6.14
104 4.09 220 8.66 1215 47.83 343 13.5 1520 59.84 1727 67.99 2236 88.03 484 19.1 1671 65.8 146 5.74 209 8.22 156 6.14 220 8.66 352 13.85 6600 259.84 7540 285 10650 419.29 9460 372.44 5610 220.86
Guaranteed Spec
65
49
91
2.55
1.92
3.58
200
26
197
7.87
1.02
7.75
1215
10
1022
47.83
0.39
40.23
341
10
310
13.4
0.4
12.2
1520
10
1435
59.84
0.39
56.49
1727
10
1446
67.99
0.39
57.71
2236
10
1840
88.03
0.39
72.44
484
0
447
19.1
0
447
1671
10
1564
65.8
0.4
61.6
111
42
137
4.37
1.65
5.39
189
26
194
7.44
1.02
7.63
106
65
142
4.17
2.55
5.59
190
41
188
7.48
1.61
7.40
352
10
315
13.85
0.39
12.40
6514
94
5460
256.45
3.70
214.96
7404
145
6312
279.6
5.7
248.5
10370
288
8820
408.26
11.33
347.24
9288
190
8060
365.66
7.48
317.32
5454
170
4360
214.72
6.69
171.65
42 1.65 171 6.73 1425 56.10 300 11.8 1425 56.10 1436 56.53 1830 72.04 17.6 17.6 1554 61.2
95 3.74 168 6.61
77 3.03 147 5.78 305 12.00 5366 211.25 6167 242.8 8532 335.90 7870 309.84 4190 164.96
266
Granit XP User Guide
Granit XP XLR Performance
Focus
5 mil Code 39
mm
in.
10 mil DM
mm
in.
10 mil Code 39
mm
in.
13 mil UPCA
mm
in.
20 mil Code 39
mm
in.
55 mil Code 39
mm
in.
100 mil Code 39
mm
in.
100 mil DM
mm
in.
Average Spec 87
3.43 89 3.5 48
1.89 11
0.43 15
0.59 * * * * * *
370 14.57
393 15.47 2202 86.70 2244 88.35 5944 234.02 15530 611.42 23212 913.86 11413 449.33
* code width limited
Guaranteed Spec
283
108
338
11.14
4.25
13.31
304
122
357
11.97
4.80
14.05
2154
64
1461
84.8
2.51
57.52
2233
38
1970
87.91
1.5
77.55
5929
33
5300
233.43
1.30
208.67
*
12500
*
492.13
*
20000
*
787.40
*
6500
*
255.91
230 9.06 235 9.25 1397 55.01 1932 76.06 5267 207.37
Granit XP User Guide
267
Standard Connector Pinouts
Note: The following pin assignments are not compatible with some Honeywell legacy products. Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the manufacturer may result in damage not covered by your warranty.
Keyboard Wedge
10 Pin RJ41 Modular Plug - connects to the base
1 Cable shield 2 Cable select 3 Supply ground 4 Terminal data 5 Terminal clock 6 Keyboard clock 7 +5V power 8 Keyboard data 9 10
Serial Output
10 Pin RJ41 Modular Plug - connects to the base
1 Cable shield 2 Cable select 3 Supply ground 4 Transmit data 5 Receive data - serial data to scanner 6 CTS 7 +5V power 8 RTS 9 10
268
Granit XP User Guide
RS485 Output
10 Pin RJ41 Modular Plug - connects to the base
Note: RS485 signal conversion is performed in the cable.
1 Cable shield 2 Cable select 3 Supply ground 4 Transmit data 5 Receive data - serial data to scanner 6 7 +5V power 8 Transmit Enable 9 10
USB
10 Pin Modular Plug - connects to the base
1 Cable shield 2 Cable select 3 Supply ground 4 5 6 7 +5V power 8 9 Data + 10 Data -
Granit XP User Guide
269
Required Safety Labels
Scanner
Laser Label location
Part Number, Serial Number and Revision Information location
Compliance label location
270
Granit XP User Guide
CCB22-100BT-03N-BF Base
Granit XP User Guide
271
272
Granit XP User Guide
CHAPTER
12 MAINTENANCE AND TROUBLESHOOTING
Repairs
Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support on page xiii).
Maintenance
Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the following sections describe periodic checks to ensure dependable operation.
Clean the Scanner
The scanner or base's housing and scanner window may be cleaned with a soft cloth dampened with water or a mild detergent-water solution. If a mild detergent solution is used, wipe the scanner or base with a clean cloth dampened only with water to remove any detergent residue.
Note: Reading performance may degrade if the scanner's window is not clean. If the window is visibly dirty, or if the scanner isn't operating well, clean the window.
Caution: Do not submerge the scanner in cleaning solution. Do not use abrasive wipes or cloths on the scanner's window. Abrasive wipes may scratch the window. Never use solvents (e.g., acetone) on the housing or window. Solvents may damage the finish or the window.
Caution: Ensure all components are dry prior to mating the scanner with charging accessories or other peripheral devices. Mating wet components may cause damage not covered by the warranty.
Granit XP User Guide
273
Inspect Cords and Connectors
Inspect the interface cable and connector for wear or other signs of damage. A badly worn cable or damaged connector may interfere with scanner operation. Contact your distributor for information about cable replacement and see Replace Cables in Corded Scanners on page 274.
Replace Cables in Corded Scanners
The standard interface cable is attached to the scanner with an 10-pin modular connector. When properly seated, the connector is held in place with a screw and locking plate. The interface cable is designed to be field replaceable. · Order replacement cables from Honeywell or from an authorized distributor. · When ordering a replacement cable, specify the cable part number of the
original interface cable.
Replace an Interface Cable
1. Turn off the power to the host system. 2. Disconnect the scanner's cable from the terminal or computer. 3. Locate the small screw at the bottom of the locking plate. 4. Loosen the screw. 5. Loosen the locking plate and slide it over the base of the cable connector to
remove the cable from the device. 6. Remove the O-ring from the end of the cable connection. 7. See Connect a Corded Device, to connect the new cord to the scanner.
Replace Cables and Batteries in Cordless Systems
Replace an Interface Cable in a Base
1. Turn the power to the host system OFF. 2. Disconnect the base's cable from the terminal or computer. 3. Turn the base upside down. 4. Pull the connector out while maintaining pressure on the connector release
clip. 5. Replace with the new cable. Insert the connector into the opening and press
firmly. The connector is keyed to go in only one way, and will click into place.
274
Granit XP User Guide
Change a Scanner Battery
1. Rotate metal twist at bottom of battery door counterclockwise. 2. Remove battery. 3. Insert replacement battery. 4. Replace end cap and screw together.
Troubleshoot a Corded Scanner
The scanner automatically performs self-tests whenever you turn it on. If your scanner is not functioning properly, review the following Troubleshooting Guide to try to isolate the problem.
Is the power on? Is the aimer on?
If the aimer isn't illuminated, check that: · The cable is connected properly. · The host system power is on (if external power isn't used). · The trigger works.
Is the scanner having trouble reading your symbols?
If the scanner isn't reading symbols well, check that the symbols: · Aren't smeared, rough, scratched, or exhibiting voids. · Aren't coated with frost or water droplets on the surface. · Are enabled in the scanner or in the decoder to which the scanner connects.
Is the barcode displayed but not entered?
The barcode is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example). · You need to program a suffix. Programming a suffix enables the scanner to
output the barcode data plus the key you need (such as "CR") to enter the data into your application. Refer to Prefix/Suffix Overview on page 113 for further information.
If you aren't sure what programming options have been set in the scanner, or if you want the factory default settings restored, refer to Reset the Factory Defaults on page 226.
Granit XP User Guide
275
Troubleshoot a Cordless System
Troubleshoot a Base
Note: Visit the Services and Support section of our website (sps.honeywell.com) to check for the latest software for both the scanner and the base. If your base is not functioning properly, review the following troubleshooting guidelines to try to isolate the problem. Is the red LED on? If the red LED isn't illuminated, check that: · The power cable is connected properly and there is power at the power source. · The host system power is on (if external power isn't used). Is the green LED on? If the green LED isn't illuminated, check that: · The scanner is correctly placed in the base. · There is external power or 12 volt host power. · Charge mode is turned on. (See "Beeper and LED Sequences and Meaning" on page 45) · The battery is not bad or deeply discharged. In some cases, the scanner's battery may trickle charge to bring it into an acceptable level and then transition to a normal charge cycle.
Troubleshoot a Cordless Scanner
Note: Make sure that your scanner's battery is charged. Visit the Services and Support section of our website (sps.honeywell.com) to check for the latest software for both the scanner and the base or Access Point. Is the scanner having trouble reading your symbols? If the scanner isn't reading symbols well, check that the symbols: · Aren't smeared, rough, scratched, or exhibiting voids. · Aren't coated with frost or water droplets on the surface. · Are enabled in the base or Access Point to which the scanner connects. Is the barcode displayed but not entered into the application? The barcode is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or the Tab key, for example). · You need to program a suffix. Programming a suffix enables the scanner to output the barcode data plus the key you need (such as "CR") to enter the data
276
Granit XP User Guide
into your application. Refer to Prefix/Suffix Overview on page 113 for further information.
The scanner won't read your barcode at all.
· Scan the sample barcodes in the back of this manual. If the scanner reads the sample barcodes, check that your barcode is readable.
· Verify that your barcode symbology is enabled (see Chapter 7).
Granit XP User Guide
277
278
Granit XP User Guide
APPENDIX
A REFERENCE CHARTS
Symbology Charts
Note: "m" represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details.
Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry.
Refer to Data Edit beginning on page 113 and Data Format beginning on page 119 for information about using Code ID and AIM ID.
Linear Symbologies
Linear Symbology
All Symbologies Codabar Code 11 Code 128 Code 32 Pharmaceutical (PARAF) Code 39 (supports Full ASCII mode)
TCIF Linked Code 39 (TLC39) Code 93 and 93i
EAN EAN-13 (including Bookland EAN) EAN-13 with Add-On EAN-13 with Extended Coupon Code EAN-8
AIM
ID
]Fm ]H3 ]Cm ]X0 ]Am ]L2 ]Gm
]Em ]E0 ]E3 ]E3 ]E4
Honeywell
Possible modifiers (m)
ID
Hex
99
0-1
a
61
h
68
0, 1, 2, 4
j
6A
<
3C
0, 1, 3, 4, 5, 7
b
62
T
54
0-9, A-Z, a-m
i
69
0, 1, 3, 4
d
64
d
64
d
64
d
64
D
44
Granit XP User Guide
279
Linear Symbology
EAN-8 with Add-On GS1
GS1 DataBar GS1 DataBar Limited GS1 DataBar Expanded GS1-128 2 of 5 China Post (Hong Kong 2 of 5) Interleaved 2 of 5 Matrix 2 of 5 NEC 2 of 5 Straight 2 of 5 IATA Straight 2 of 5 Industrial MSI Telepen UPC UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1
Add Honeywell Code ID Add AIM Code ID Add Backslash Batch mode quantity
AIM ID
]E3
]em ]em ]em ]C1
]X0 ]Im ]X0 ]X0 ]Rm ]S0 ]Mm ]Bm
]E0 ]E3 ]E3 ]E0 ]E3 ]X0
Honeywell
Possible modifiers (m)
ID
Hex
D
44
0
y
79
{
7B
}
7D
I
49
Q
51
0, 1, 3
e
65
m
6D
Y
59
0, 1, 3
f
66
f
66
0, 1
g
67
t
74
0, 1, 2, 3, 8, 9, A, B, C
c
63
c
63
c
63
E
45
E
45
E
45
5C80
5C81
5C5C
5
35
280
Granit XP User Guide
2D Symbologies
2D Symbology
All Symbologies Aztec Code Chinese Sensible Code (Han Xin Code) Codablock A Codablock F Data Matrix Dot Code GS1
GS1 Composite GS1 DataBar Omnidirectional MaxiCode PDF417 MicroPDF417 QR Code Micro QR Code
Postal Symbologies
Postal Symbology
All Symbologies Australian Post British Post Canadian Post China Post InfoMail Intelligent Mail Barcode Japanese Post KIX (Netherlands) Post Korea Post Planet Code Postal-4i Postnet
Granit XP User Guide
AIM
ID
]zm ]X0 ]O6 ]Om ]dm ]J0 ]em ]em ]em ]Um ]Lm ]Lm ]Qm ]Qm
Honeywell
Possible modifiers (m)
ID
Hex
99
0-9, A-C
z
7A
H
48
0, 1, 4, 5, 6
V
56
0, 1, 4, 5, 6
q
71
0-6
w
77
.
2E
0-3
y
79
0-3
y
79
0-3
y
79
0-3
x
78
0-2
r
72
0-5
R
52
0-6
s
73
s
73
AIM
ID
]X0 ]X0 ]X0 ]X0 ]X0 ]X0 ]X0 ]X0 ]X0 ]X0 ]X0 ]X0
Honeywell
Possible modifiers (m)
ID
Hex
99
A
41
B
42
C
43
Q
51
,
2c
M
4D
J
4A
K
4B
?
3F
L
4C
N
4E
P
50
281
ASCII Conversion Chart (Code Page 1252)
In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.
Non-printable
ASCII
control characters
DEC
0 1 2 3 4 5 6 7 8 9 10 11
12
13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 127
HEX
00 01 02 03 04 05 06 07 08 09 0A 0B
0C
0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 7F
Char
NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT
FF
CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US
Keyboard Control + ASCII (CTRL+X) Mode
Control + X Mode Off (KBDCAS0)
Reserved NP Enter Caps Lock ALT Make ALT Break CTRL Make CTRL Break Enter / Ret (Apple Make) Tab (Apple Break) Tab
Delete
Enter / Ret Insert ESC F11 Home PrtScn Backspace Back Tab F12 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 NP Enter
Windows Mode Control + X
Mode On (KBDCAS2)
CTRL + X
CTRL + X function
CTRL+ @
CTRL+ A
Select all
CTRL+ B
Bold
CTRL+ C
Copy
CTRL+ D
Bookmark
CTRL+ E
Center
CTRL+ F
Find
CTRL+ G
CTRL+ H
History
CTRL+ I
Italic
CTRL+ J
Justify
CTRL+ K
hyperlink
CTRL+ L
list, left align
CTRL+ M
CTRL+ N
New
CTRL+ O
Open
CTRL+ P
Print
CTRL+ Q
Quit
CTRL+ R
CTRL+ S
Save
CTRL+ T
CTRL+ U
CTRL+ V
Paste
CTRL+ W
CTRL+ X
CTRL+ Y
CTRL+ Z
CTRL+ [
CTRL+ \
CTRL+ ]
CTRL+ ^
CTRL+ -
282
Granit XP User Guide
Lower ASCII Reference Table
Note: Windows Code page 1252 and lower ASCII use the same characters.
Printable Characters DEC HEX Character
32
20
<SPACE>
33
21
!
34
22
"
35
23
#
36
24
$
37
25
%
38
26
&
39
27
'
40
28
(
41
29
)
42
2A
*
43
2B
+
44
2C
,
45
2D
-
46
2E
.
47
2F
/
48
30
0
49
31
1
50
32
2
51
33
3
52
34
4
53
35
5
54
36
6
55
37
7
56
38
8
57
39
9
58
3A
:
59
3B
;
60
3C
<
61
3D
=
62
3E
>
63
3F
?
DEC
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
HEX
40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F
Character DEC
@
96
A
97
B
98
C
99
D
100
E
101
F
102
G
103
H
104
I
105
J
106
K
107
L
108
M
109
N
110
O
111
P
112
Q
113
R
114
S
115
T
116
U
117
V
118
W
119
X
120
Y
121
Z
122
[
123
\
124
]
125
^
126
_
127
HEX
60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F
Character
` a b c d e f g h i j k l m n o p q r s t u v w x y z { | } ~
Extended ASCII Characters
DEC HEX CP 1252 ASCII
128
80
Ç
129
81
ü
130
82
,
é
131
83
â
132
84
,,
ä
133
85
...
à
134
86
å
135
87
ç
136
88
^
ê
137
89
ë
138
8A
S
è
139
8B
<
ï
Alternate Extended
up arrow down arrow right arrow left arrow
Insert Delete Home End Page Up Page Down Right ALT Right CTRL
PS2 Scan Code
0x48
0x50
0x4B
0x4D
0x52 0x53 0x47 0x4F 0x49 0x51 0x38 0x1D
Granit XP User Guide
283
284
Extended ASCII Characters (Continued)
DEC HEX CP 1252 ASCII
Alternate Extended
140
8C
OE
î
Reserved
141
8D
ì
Reserved
142
8E
Z
Ä
Numeric Keypad Enter
143
8F
Å
Numeric Keypad /
144
90
É
F1
145
91
`
æ
F2
146
92
'
Æ
F3
147
93
"
ô
F4
148
94
"
ö
F5
149
95
·
ò
F6
150
96
û
F7
151
97
--
ù
F8
152
98
~
ÿ
F9
153
99
TM
Ö
F10
154
9A
s
Ü
F11
155
9B
>
¢
F12
156
9C
oe
£
Numeric Keypad +
157
9D
¥
158
9E
z
Numeric Keypad Numeric Keypad *
159
9F
Y
Caps Lock
160
A0
á
Num Lock
161
A1
¡
í
Left Alt
162
A2
¢
ó
Left Ctrl
163
A3
£
ú
Left Shift
164
A4
¤
ñ
Right Shift
165
A5
¥
Ñ
Print Screen
166
A6
¦
ª
Tab
167
A7
§
º
Shift Tab
168
A8
¨
¿
169
A9
©
Enter Esc
170
AA
ª
¬
Alt Make
171
AB
«
½
Alt Break
172
AC
¬
¼
Control Make
173
AD
¡
Control Break
174
AE
®
«
Alt Sequence with 1 Character
175
AF
¯
»
176
B0
°
177
B1
±
178
B2
²
179
B3
³
180
B4
´
181
B5
µ
182
B6
¶
183
B7
·
184
B8
¸
185
B9
¹
186
BA
º
187
BB
»
188
BC
¼
189
BD
½
190
BE
¾
191
BF
¿
192
C0
À
193
C1
Á
Ctrl Sequence with 1 Character
PS2 Scan Code
n/a n/a 0x1C 0x35 0x3B 0x3C 0x3D 0x3E 0x3F 0x40 0x41 0x42 0x43 0x44 0x57 0x58 0x4E 0x4A 0x37 0x3A 0x45 0x38 0x1D 0x2A 0x36 n/a 0x0F 0x8F 0x1C 0x01 0x36 0xB6 0x1D 0x9D 0x36 0x1D
Granit XP User Guide
Extended ASCII Characters (Continued)
DEC HEX CP 1252 ASCII
Alternate Extended
194
C2
Â
195
C3
Ã
196
C4
Ä
197
C5
Å
í
198
C6
Æ
199
C7
Ç
200
C8
È
201
C9
É
202
CA
Ê
203
CB
Ë
204
CC
Ì
205
CD
Í
206
CE
Î
207
CF
Ï
208
D0
Ð
209
D1
Ñ
210
D2
Ò
211
D3
Ó
212
D4
Ô
213
D5
Õ
214
D6
Ö
215
D7
×
216
D8
Ø
217
D9
Ù
218
DA
Ú
219
DB
Û
220
DC
Ü
221
DD
Ý
222
DE
Þ
223
DF
ß
224
E0
à
225
E1
á
ß
226
E2
â
227
E3
ã
228
E4
ä
229
E5
å
230
E6
æ
µ
231
E7
ç
232
E8
è
233
E9
é
234
EA
ê
235
EB
ë
236
EC
ì
237
ED
í
238
EE
î
239
EF
ï
240
F0
ð
241
F1
ñ
±
242
F2
ò
243
F3
ó
244
F4
ô
245
F5
õ
246
F6
ö
÷
247
F7
÷
Granit XP User Guide
PS2 Scan Code
285
Extended ASCII Characters (Continued)
DEC HEX CP 1252 ASCII
Alternate Extended
248
F8
ø
°
249
F9
ù
250
FA
ú
·
251
FB
û
252
FC
ü
253
FD
ý
²
254
FE
þ
255
FF
ÿ
PS2 Scan Code
ISO 2022/ISO 646 Character Replacements
Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the barcode being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, select the code page with which the barcodes were created. The data characters should then appear properly.
286
Code Page Selection Method/ Country
Standard
Keyboard Country
Honeywell Code Page Option
United States (standard ASCII)
ISO/IEC 646-IRV
n/a
1
Automatic National Character Replacement
ISO/IEC 2022
n/a
2 (default)
Binary Code page
n/a
n/a
3
Default "Automatic National Character replacement" will select the below Honeywell Code Page options for Code128, Code 39 and Code 93.
United States
ISO/IEC 646-06
0
1
Canada
ISO /IEC 646-121
54
95
Canada
ISO /IEC 646-122
18
96
Japan
ISO/IEC 646-14
28
98
China
ISO/IEC 646-57
92
99
Great Britain (UK)
ISO /IEC 646-04
7
87
France
ISO /IEC 646-69
3
83
Germany
ISO/IEC646-21
4
84
Switzerland
ISO /IEC 646-CH
6
86
Sweden / Finland (extended Annex C)
ISO/IEC 646-11
2
82
Ireland
ISO /IEC 646-207
73
97
Denmark
ISO/IEC 646-08
8
88
Norway
ISO/IEC 646-60
9
94
Italy
ISO/IEC 646-15
5
85
Portugal
ISO/IEC 646-16
13
92
Spain
ISO/IEC 646-17
10
90
Spain
ISO/IEC 646-85
51
91
Granit XP User Guide
Dec Hex
35
36
64
91
92
93
94
96
123
124
125
126
23
24
40
5B
5C
5D
5E
60
7B
7C
7D
7E
US
0
1
# $@ [
\
]
^
`
{
|
}
~
CA
54
95
#
$
à
â
ç
ê
î
ô
é
ù
è
û
CA
18
96
#
$
à
â
ç
ê
É
ô
é
ù
è
û
JP
28
98
# $@ [
¥
]
^
`
{
|
}
CN
92
99
# ¥@ [
\
]
^
`
{
|
}
GB
7
87
£ $@ [
\
]
^
`
{
|
}
~
FR
3
83
£
$
à
°
ç
§
^
µ
é
ù
è
¨
DE
4
84
#
$
§
ÄÖ
Ü
^
`
ä
ö
ü
ß
CH
6
86
ù
$
à
é
ç
ê
î
ô
ä
ö
ü
û
SE/FI
2
82
#
¤
É
Ä
Ö
Å
Ü
é
ä
ö
å
ü
DK
8
88
# $ @ÆØ Å ^
`
æ
ø
å
~
NO
9
94
# $ @ÆØ Å ^
`
æ
ø
å
¯
IE
73
97
£$ÓÉ
Í
ÚÁó
é
í
ú
á
IT
5
85
£
$
§
°
ç
é
^
ù
à
ò
è
ì
PT
13
92
#
$
§
Ã
Ç
Õ
^
`
ã
ç
õ
°
ES
10
90
#$
§
¡
Ñ
¿
^
`
°
ñ
ç
~
ES
51
91
#$
·
¡
Ñ
Ç
¿
`
´
ñ
ç
¨
ISO / IEC 646 National Character Replacements
COUNTRY Countr y Keyboard Honeywell CodePage
Granit XP User Guide
287
Keyboard Key References
6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D
1E 1F 20 21 22 23 24 25 26 27 28 29 2B
2C 2E 2F 30 31 32 33 34 35 36 37 39
3A 3B 3C
3D
3E 3F 38 40
4B 50 55 4C 51 56
53 4F 54 59
5A 5F 64 69 5B 60 65 6A 5C 61 66 5D 62 67
63 68 6C
104 Key U.S. Style Keyboard
6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 2B 1E 1F 20 21 22 23 24 25 26 27 28 29 2A
2C 2D 2E 2F 30 31 32 33 34 35 36 37 39
3A 3B 3C
3D
3E 3F 38 40
4B 50 55 4C 51 56
53 4F 54 59
5A 5F 64 69
5B 60 65 6A 5C 61 66
5D 62 63
67 68
6C
105 Key European Style Keyboard
288
Granit XP User Guide
SAMPLE SYMBOLS
UPC-A
0 123456 7890
EAN-13
Code 128
Code 128
9 780330 290951
Codabar
Code 93
123456-9$
RSS-14
(01) 00123456789012
A13579B
Matrix 2 of 5
6543210
Code 49
1234567890
Granit XP User Guide
Interleaved 2 of 5
01234567890
Code 39
BC321
Straight 2 of 5 Industrial
123456
PDF417
Car Registration
289
SAMPLE SYMBOLS (CONTINUED)
Postnet
Zip Code
QR Code
Data Matrix
Test Symbol
MaxiCode
Numbers
Micro PDF417
Test Message
DotCode
Test Message
12345
290
Granit XP User Guide
PROGRAMMING CHART
0 2
4 6 8
Granit XP User Guide
1 3 5 7 9
291
PROGRAMMING CHART (CONTINUED)
A B
C D
E F
Save Discard
Reset
Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
292
Granit XP User Guide
Honeywell 855 S. Mint St. Charlotte, NC 28202
sps.honeywell.com
TM
199x-EN-UG-01 Rev E 08/22
iLovePDF