Element ESBAB20RTR 2.0 Sound Bar User Manual

What's Included

Your new sound bar!

• Power cable
• HDMI cable
• Remote control
• 2 AAA remote batteries
• 2 mounting screws and 2 wall plugs

For Your Attention

Important Safety and Usage Information

• Read this manual before operating. Retain for future reference.
• Do not open the cabinet; refer servicing to qualified personnel.
• Switch off and disconnect from AC power when not in use for extended periods.
• Do not install in places exposed to heating sources, direct sunshine, moisture, or rain.
• Avoid dripping or splashing; do not place liquid-filled objects on the unit.
• Install on a horizontal, flat, firm surface with good ventilation. Do not block vents to prevent overheating.
• Clean the exterior with a soft, clean rag; avoid chemicals or detergents.
• This guide is for user operation, not a configuration criterion.
• Use only manufacturer-specified attachments/accessories.
• Ensure the main plug remains readily operable as the disconnect device.
• WARNING: Batteries should not be exposed to excessive heat (sunshine, fire, etc.).
• CAUTION: Risk of explosion if battery is replaced incorrectly. Use only the same or equivalent type.

Safety Symbols Explained

• [Lightning Flash Symbol]: Indicates dangerous voltage within the product that may cause electric shock. Do not open the cover; refer servicing to qualified personnel.
• [Exclamatory Mark Symbol]: Indicates important operating instructions.

Mounting Your Sound Bar on a Wall

Installation Instructions

• To prevent injuries, fasten the sound bar securely to the wall.
• Drill two holes into the wall, approximately 6mm in diameter, spaced 660mm apart.
• Insert the two supplied wall plugs into the holes.
• Insert the two supplied screws into the plugs and tighten.
• Ensure there is a 4mm distance between the screw heads and the wall.
• Hang the assembled sound bar onto the screws.

Sound Bar Panels

Front Panel

• 1 Speaker
• 2 Display screen
• 3 Remote sensor
• 4 Power: Turns the sound bar on or off.
• 5 Source: Selects the input audio source.
• 6 Volume Up: Increases audio volume.
• 7 Volume Down: Decreases audio volume.

Side Panel

• (Controls labeled 4, 5, 6, 7)

Back Panel

• 8 AC IN: Power input.
• 9 HDMI (ARC): For HDMI Audio Return Channel connection.
• 10 USB: For USB media playback or firmware updates (if applicable).
• 11 OPTICAL: For Optical audio input.
• 12 AUX IN: For auxiliary audio input.

Connecting to Your TV

Connection Options

• 1. HDMI (ARC): Best Quality (cable included).
• 2. Optical: Better Quality (cable not included).
• 3. Aux: Good Quality (cable not included).

ARC (Audio Return Channel)

• ARC is an audio return channel function for digital audio, providing the best sound quality.
• Connect the supplied HDMI cable to the HDMI ARC input on the sound bar and the HDMI ARC output on your TV or external device.
• Note: Ensure the external device audio output is set to PCM.
• Ensure HDMI CEC is enabled on your TV for optimal performance.

Roku TV™ Ready™

• This sound bar is Roku TV Ready™ certified.
• If you have a Roku TV™, connect the supplied HDMI cable to your sound bar and TV, then follow the on-screen instructions for simple setup.

Optical Connection

• Connect your sound bar to your TV or other external devices (CD, VCR, DVD player, etc.) using an optical input cable (not included).
• Connect the cable to your sound bar's optical input and the external device's optical output.
• Press the [OPT] button on the remote to switch to optical input mode. The display will show "OPT".
• Note: Ensure the external device audio output is set to PCM.

AUX IN Connection

• This sound bar features auxiliary audio input terminals.
• Connect your sound bar to your TV or other external devices using an AUX input cable (not included).
• Connect the cable to your sound bar's AUX input and the external device's AUX output.
• Press the [AUX] button on the remote to switch to AUX input mode. The display will show "LINE".

Connections

Bluetooth Pairing and Operation

• Press the STANDBY button on the remote to power on the sound bar.
• Press the [Bluetooth] button on the remote to switch to Bluetooth mode. The display will show "BT".
• If "BT" is not displayed, the sound bar may still be searching. Follow these steps for pairing:
• 1. Press and hold the [Bluetooth] button on the remote.
• 2. On your smart device, search for the Bluetooth signal of the sound bar.
• 3. Select "ESBAB20RTR" from the list and enter the password "0000" if prompted.
• 4. The sound bar will sync and play audio from your device. "BT" and a beep indicate a successful connection.
• Bluetooth connection range is approximately 10 meters (33 feet).
• In Bluetooth mode, the remote buttons [PLAY/PAUSE], [NEXT], [PREVIOUS], [VOLUME+/-] are active.

Disconnecting Bluetooth

• Press and hold the [Bluetooth] button on the remote. The screen will show "no BT" upon disconnection.

Remote Control

Operation

• Insert batteries into the remote control.
• Point the remote control at the remote sensor on the front panel.
• The remote operates within approximately 8 meters (26 feet) and a 30-degree angle from the left and right sides.

Battery Installation

• Remove the battery compartment cover on the back of the remote.
• Load two AAA/1.5V batteries, ensuring correct polarity (+/-) matches the indicators inside the compartment.
• Replace the cover.
• NOTE: Remove batteries if the remote will not be used for a long time. Weak batteries can leak and damage the remote. Do not expose batteries to excessive heat. Dispose of batteries responsibly according to local regulations.

Basic Playback

• Power: Press to switch on the unit. Press again to enter standby mode.
• Bluetooth: Press to enter BT mode. Hold for 3 seconds to disconnect Bluetooth.
• Source: Press repeatedly to cycle through Bluetooth, AUX IN, USB, OPTICAL IN, and ARC modes.
• Equalizer (EQ): Press repeatedly to cycle through EQ1 (MUSIC), EQ2 (MOVIE), and EQ3 (NEWS) modes.
• ARC: Press to enter Audio Return Channel mode.
• OPT: Press to enter Optical mode.
• Play/Pause: Press to pause playback; press again to resume.
• Next: Press to skip to the next track.
• Previous: Press to return to the previous track.
• Volume Up [+]: Press to increase volume.
• Volume Down [-]: Press to decrease volume.
• Mute: Press to temporarily mute sound; press again to unmute.

Troubleshooting

Common Issues and Solutions

• If your issue is not listed or the troubleshooting guide does not resolve it, contact Element customer support.

Sound Bar Specifications

• Power Supply: AC ~100-240V, 50/60Hz
• Frequency Response: 60Hz~20kHz
• Max Power Output: 25W X 2

Working Environment

• Relative Humidity: 5% ~ 90%
• Temperature: 14°F - 95°F

References and License

References

• Element TV Company, LP. is not responsible for data compromised during wireless transmission.
• Frequency Band: Uses the 2.4 GHz frequency band.
• Certification: Conforms to frequency restrictions and laws; wireless permit not necessary.
• Restrictions of Use: Wireless transmission and usage with all Bluetooth devices not guaranteed. Devices must conform to Bluetooth SIG, Inc. standards. Connection/operation may vary by device. Use caution with Bluetooth data transmission due to security features. This system cannot transmit data to a Bluetooth device.
• Range of Use: Maximum range of 10 meters (33 feet). Range may decrease due to environment, obstacles, or interference.
• Interference: May not function properly near other Bluetooth devices or 2.4 GHz devices. May be affected by strong radio waves from nearby stations.
• Intended Usage: For normal, general use. Do not use near sensitive RF environments (e.g., airports, hospitals).

License Information

• Bluetooth®: Word mark and logos are registered trademarks of Bluetooth SIG, Inc. used under license by Element TV Company, LP.
• HDMI: Terms, High-Definition Multimedia Interface, and logo are trademarks of HDMI Licensing Administrator, Inc.
• Roku TV™: Roku TV Ready™, and Roku TV Ready™ logo are trademarks of Roku, Inc.

FCC Statement

• This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) no harmful interference, and (2) acceptance of any received interference.
• Changes or modifications not expressly approved by the responsible party could void the user's authority to operate the equipment.
• This equipment has been tested and complies with Class B digital device limits per FCC Rules, providing reasonable protection against harmful interference in residential installations. It generates, uses, and can radiate radio frequency energy. If interference occurs, try correcting it by: reorienting/relocating the antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer/technician.

Radiation Exposure Statement

• This equipment complies with FCC/IC radiation exposure limits for uncontrolled environments. Install and operate with a minimum distance of 20cm between the radiator and your body.

Register Your Product

Benefits of Registering

• Support: Get assistance quickly by pre-registering.
• News & Offers: Access latest news and special offers.
• Updates: Stay current with product updates and notifications.

How to Register

• Visit elementelectronics.com/register.

We're Here to Help

Support Resources

• Find resources for setup, connecting devices, technical issues, and downloading manuals.
• Available 24 hours a day, 7 days a week.

Contact Information

• Website: elementelectronics.com
• Phone: 1.888.842.3577
• Email: customerservice@elementelectronics.com

For Support

• Visit elementelectronics.com/support