Panduit | Network Infrastructure and Industrial Electrical Wiring
Instruction Manual for PANDUIT models including: CJUDCAPBU-X, CJUDCAPIW-X, CJUD6X88TG, CJUDCAPBU-X Angled Wire Cap, Angled Wire Cap, Wire Cap, Cap
PAN CJUDCAPBU-X 45? Angled Wire Cap | Energy Avenue
File Info : application/pdf, 6 Pages, 1.90MB
DocumentDocument© Panduit Corp. 2023 45° Up/Down UTP TG Modular Jacks & Wire Caps Part Numbers: CJUDCAPBU-X, CJUDCAPIW-X, CJUD6X88TG** INSTALLATION INSTRUCTIONS Jack PN610D Category 6A (CJUDCAPBU-X) Category 6 (CJUDCAPIW-X) Compatible Jack Modules with Angled Wire Caps 45° Up/Down Wire Cap 45° ANGLED JACK CJUD6X88TG** STANDARD CJ%%88TG** SPRING SHUTTERED CJH%%88TG** KEYED CJK%%88TG** CORROSION RESISTANT CJE6X88TG** Understanding the Label IMPORTANT!: Determine the desired direction of cable before wiring the cap. The cap, in relation to the jack, must be kept consistent throughout the entire termination. Down Orientation Up Orientation Follow dotted line instructions for Down Orientation. (pages 4-5) Follow solid line instructions for Up Orientation. (pages 2-3) %% Denotes Category. ** Denotes color. For Technical Support: www.panduit.com Page 1 of 6 © Panduit Corp. 2023 1 INSTALLATION INSTRUCTIONS Up Orientation PN610D IMPORTANT!: Be sure that strain relief is fully retracted before inserting cable. 2 Cable End 1 1.5" (38.1m m ) 0.5" (12.7m m ) 0.5" (12.7m m ) Cable End 2 1.5" (38.1m m ) 3 4 5 Bend wires to ease inserting them into the cap. 1 Do not pre-arrange conductors. 2 Cable End 1 Shown Be sure cable is fully 6 inserted into wire cap TGSJT Cable End 1 Shown For Technical Support: www.panduit.com Page 2 of 6 Cable End (1) Cable End (2) © Panduit Corp. 2023 7 T568B Wiring B B B B Termination side Cable End 1 Label side 1. Cable End 2 1. 8 INSTALLATION INSTRUCTIONS Up Orientation PN610D T568A Wiring T568A not shown on wire map label A A Cable End 1 A A Termination side Label side 1. 2. A Cable End 2 2. 1. B A 2. A B 9 A Important! Maintain orientation of cap in relation to jack from previous steps. 10 11 For Technical Support: www.panduit.com Page 3 of 6 © Panduit Corp. 2023 INSTALLATION INSTRUCTIONS Down Orientation PN610D IMPORTANT!: Be sure that strain relief is fully retracted before inserting cable. 2 0.5" (12.7m m ) Cable End 1 1.5" (38.1m m ) Cable End 2 1.5" (38.1m m ) 0.5" (12.7m m ) 3 4 Bend wires to 5 ease inserting them into the cap. Do not pre-arrange conductors. 2 Cable End 1 Shown Be sure cable is fully 6 inserted into wire cap TGSJT Cable End (1) 1 Cable End (2) Cable End 1 Shown For Technical Support: www.panduit.com Page 4 of 6 © Panduit Corp. 2023 7 T568B Wiring B B B B Termination side Cable End 1 Label side 1. B INSTALLATION INSTRUCTIONS Down Orientation PN610D T568A Wiring T568A not shown on wire map label A A Cable End 1 A Termination side A Label side 1. 2. A B Cable End 2 1. Cable End 2 2. 1. B B 8 9 A 2. A A Important! Maintain orientation of cap in relation to jack from previous steps. 10 11 For Technical Support: www.panduit.com Page 5 of 6 © Panduit Corp. 2023 1 INSTALLATION INSTRUCTIONS REMOVAL STEPS 2 3 PN610D Notes: 1. For specified performance, follow TIA/EIA 568-C installation guidelines. 2. Jack Modules can terminate 22-26 AWG solid data cable with 0.062" (1.57mm) maximum insulated conductor outside diameter. 3. Jack Modules may be re-terminated at least 20 times. 4. For technical and performance information, consult Panduit Technical Support. As with all Wiring Accessories, the following statements apply: 1. Never install communications wiring during a lightning storm. 2. Never install communications wiring in wet locations unless the jack is specifically designed for use in wet locations. 3. Never touch uninsulated communications wiring or terminals unless the communication line has been disconnected at the network interface. 4. Use caution when installing or modifying communication wiring. For Instructions in Local Languages and Technical Support: www.panduit.com www.panduit.com Page 6 of 6 E-mail: techsupport@panduit.com Phone: 866-405-6654