Installation Guide for SDMC models including: AX1800 Dual Band WiFi6 GPON Terminal, AX1800, Dual Band WiFi6 GPON Terminal, WiFi6 GPON Terminal, GPON Terminal
Shenzhen SDMC Technology Co.,Ltd. NP1835GRF 2AW68-NP1835GRF 2AW68NP1835GRF np1835grf
NP1835GB Quick Installaon Guide Package Content NP1835GB x 1 Power Adapter x 1 Ethernet Cable x 1 Quick Installaon Guide x 1 Ports and indicators WiFi Button AX1800 Dual Band WiFi6 GPON Terminal WPS Button Power Port PON Port GE Port ON/OFF Buon Reset Buon Laptop 2 GE (Optional) 3 Power adaptor POWER 1 PON Fiber opc cable 1. Hardware connecons Connect a fiber opc cable to the PON port. Connect a computer to the GE port using the Ethernet cable (oponal). Use the included power adapter to connect the power socket to a power outlet. Press the ON/OFF buon to turn on the device. 2. WiFi connecon Using SSID Use the SSID and Wireless Key on the device label to connect wireless to the device. On your smartphone or notebook, find this SSID. Enter the Wireless Key to connect. Using WPS Press the WPS buon on the device and the WPS indicator will blink. Then press the WPS buon on the client. If the WPS method fails, use the SSID and wireless key to set up a WiFi connecon. 3. Configure on the web Configure the device on the web page according to the informaon on the device label. Open a web browser, enter the IP address, default User Name and Login Password, and then click Login. 4. LED Indicator Explanaon Name State Descripon WIFI On The device has been turned on. Power Off The device has not been turned on. Blinking No opcal signal is detected. LOS Off Opcal signal is detected. On The device has been registered. WPS PON Blinking Opcal signal is detected. Off No opcal signal is detected. On INTERNET In Roung mode and WAN connecon is up. Blinking Aempt to get an IP address. No internet connecon or the Off modem router is operang in Bridge mode. On Wi-Fi has been turned on. Blinking Wi-Fi data is being transmied. Off Wi-Fi has been shut down. The device is successfully On connected through WPS funcon. The device is being connected Blinking through WPS funcon. The WPS funcon is not enabled, or the device is Off successfully connected through WPS funcon. 5. Buon Explanaon Name Explanaon ON/OFF Turn on/off the device. RESET Hold down for more than 5 seconds and release to restore the factory sengs. Hold down the WPS buon for 1 second and release it to build mesh network. WPS Hold down the WPS buon for 5 seconds and release it to use the WPS connect the device. WiFi Enable/disable wireless network. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons,may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separaon between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiaon Exposure Statement This device complies with FCC radiaon exposure limits set forth for an uncontrolled environment. This equipment must be installed and operated in accordance with provided instrucons and the antenna(s) used for this transmier must be installed to provide a separaon distance of at least 20 cm from all persons. This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. Cauon! Any changes or modificaons not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Adobe PDF library 15.00