User Manual for LEDYi Lighting models including: WT1 WiFi and RF 2CH LED Controller, WT1, WiFi and RF 2CH LED Controller, RF 2CH LED Controller, 2CH LED Controller, LED Controller
GUANGZHOU SKYDANCE CO.,LTD WT1 WiFi& RF 2CH LED Controller 2BDBM-WT1 2BDBMWT1 wt1
WiFi & RF 2CH LED Controller Model No.: WT1 Tuya APP cloud control/Voice control/2 Channels/Push-Dim/DC power socket input/Wireless remote control Features Used for control single color or color temperature LED strip. DC power socket input and 2 channel constant voltage output. Tuya APP cloud control, support on/off, color temperature and brightness adjust, delay turn on/off light, timer run, scene edit function. Voice control, support amazon ECHO and TmallGenie smart speaker. Match with RF 2.4G remote control optional. User need set light type by press key before Tuya APP network connection and match RF remote of the same light type. Each WT1 controller can also work as WiFi-RF converter, then use Tuya APP to control one or more RF LED controller or RF LED dimming driver synchronously. Connect with external push switch to achieve on/off and 0-100% dimming function. Light on/off fade time 3s selectable. LVD RED Technical Parameters Input and Output Input voltage Input current Output voltage Output current Output power Output type 12-36VDC 10.5A 2 x (12-36)VDC 2CH,5A/CH 2 x (60-180)W Constant voltage Environment Operation temperature Case temperature (Max.) Ta: -30 OC ~ +55OC T c:+85OC Dimming data Input signal Control distance Dimming gray scale Dimming range Dimming curve PWM frequency Package Size Gross weight Tuya APP+RF 2.4GHz+PushDim 30m(Barrier-free space) 4096 (2^12) levels 0 -100% Logarithmic 2000Hz (default) L120 x W43 x H35mm 0.055kg Safety and EMC EMC standard (EMC) ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 Safety standard(LVD) Radio Equipment(RED) Certi cation EN 62368-1:2020+A11:2020 ETSI EN 300 328 V2.2.2 CE,EMC,LVD,RED Warranty and Protection Warranty 5 years Protection Reverse polarity Over-heat Short circuit Systemwiring 3G/4G/5G WiFi Tuya Cloud WiFi Mobile Phone WiFi Router 15m WT1 30m DIM RFDIM Controller DIM Wired connection Wireless connection Amazon ECHO 30m RFRemote(Optional) WT1 WT1 30m DIM RFDIM Controller DIM 30m CCT RFCCT Controller CCT 30m ZONE POWER ZONE ZONE ZONE SCENE SCENE SCENE 30m WT1 CCT RFCCT Controller CCT PanelRFRemote(Optional) Note: 1.Theabove distance is measured in spacious(noobstacle) environment, Please refer to the actual test distance before installation. 2.PleasecheckiftheWiFi routernetin2.4Gband, the5Gband isnotavailable, and donothideyourrouternetwork. 3. PleasekeepthedistancebetweenWT1 devicesandrouterclose, andchecktheWiFisignals. User Manual Ver 2.0.1 1 38.00 mm - + Push Dim LED O UTPUT WW CW WW Mechanical Structures and Installations Power input + Power input - INPUT 12-24VDC Installation rack DC socket input LED indicator Match/Set key + R UN M AT CH/SET Output LED + Output LED Installation rack Output LED Push switch Push switch common 114.00 mm 20.00 mm Wiring Diagram For single color - + Push Dim LED O UTPUT WW CW WW Power Adapter 12-36VDC + R UN M AT CH/SET INPUT 12-24VDC Single color LED strip + Single color LED strip + Dimming remote Push Switch Press and hold match/set key for 8s, until the RUN LED indicator turn white, then release, the controller will become DIM type, then do smart con g by tuya APP, or short press match key to match with dimming RF remote. For dual color CCT AC100-240V CCT remote Power Supply 12-36VDC Constant Voltage + R UN M AT CH/SET - + Push Dim LED O UTPUT WW CW WW + INPUT 12-24VDC CW WW Dual color LED strip Push Switch Press and hold match/set key for 10s, until the RUN LED indicator turn yellow, then release, the controller will become CCT type, then do smart con g by tuya APP, or short press match key to match with CCT RF remote. Note: 1. User can connect constant voltage power supply or power adapter as power input. 2. Press and hold Match/Set key for 2s, switch 2 kinds light type in sequence. 3. Switch off the power, then switch on power, repeat again. Immediately short press match key 3 times, the light on/off time will change between 3s and 0.5s. 4. For CCT light, continuous power off and on will change 3 levels color temperature (WW, NW and CW) in sequence. Push Dim DIM Single color CCT Dual Color Click Double Click Long press(>1s) from OFF Long press(>1s) from ON Click Double Click Long press(>1s) from OFF Long press(>1s) from ON ON/OFF Turn on at 100% or 10%(night light) and vice-versa Dimming UP/DOWN Dimming UP/DOWN ON/OFF Turn on at 100% or 10%(night light) and vice-versa Color temperature UP/DOWN (turn off and turn on to return dimming) Dimming UP/DOWN User Manual Ver 2.0.1 2 Tuya APP network connection Please download the corresponding tuya/smart life app according to your region. Push twice Match/Set key fastly, or when press and hold Match/Set key for 8 or10s to set 2 kinds light type: Clear previous network connection, enter Smart config mode, the purple LED indicator flash fastly, the output LED will flash 10 times. Smart life APP Tuya APP Press and hold Match/Set key for 2s: Switch 2 kinds light type in sequence, notice this operation does not automatically clear previous network connection. Press and hold Match/Set key for 5s: Clear previous network connection, enter AP config mode, the purple LED indicator flash slowly. If smart config failed, please tr y AP config. Repeat power on and off for 5 consecutive times, also clear previous network connection, enter Smart config mode, the output LED will flash 10 times. If Tuya APP network connection succeed, the RUN LED indicator will stop flash purple, and turn corresponding light type color (White: DIM, Yellow: CCT. and in Tuya APP, you can find DIM or CCT device. Tuya APP interface DIM CCT DIM: Touch brightness slide to adjust brightness. CCT: Touch color wheel to adjust color temperature. Touch brightness slide to adjust brightness. DIM CCT WT1 match remote control (Optional) End user can choose the suitable match/delete ways. Two options are offered for selection: Use the WT1's Match key Match: Short press match key of WT1, immediately press on/off key (single zone remote) or zone key (multiple zone remote) on the remote. The LED indicator fast flash a few times means match is successful. Use Power Restart Match: Switch off the power of WT1, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful. Delete: Press and hold match key of WT1 for 15s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted. Delete: Switch off the power of WT1, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. WT1 work as WiFi-RF converter to match RF LED controller or dimming driver End user can choose the suitable match/delete ways. Two options are offered for selection: Use the controller's Match key Match: Short press match key of the controller, immediately press on/off key on the Tuya APP. The LED indicator fast flash a few times means match is successful. Use Power Restart Match: Switch off the power of the controller, then switch on power, repeat again. Immediately short press on/off key 3 times on the Tuya APP. The light blinks 3 times means match is successful. Delete: Press and hold match key of the controller for 5s, The LED indicator fast flash a few times means match was deleted. Delete: Switch off the power of the controller, then switch on power, repeat again. Immediately short press on/off key 5 times on the Tuya APP. The light blinks 5 times means match was deleted. User Manual Ver 2.0.1 3 FCC Warning 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.105 Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: 1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.Corel PDF Engine Version 16.1.0.843