Layout 1

[PDF] model # AMP 100/6 model # AMP 50/12 multi-zone amplifiers

3. Heed all warnings. 4. Follow the instructions. 5. Do not use near water. 6. Clean with a dry ...

PDF preview unavailable. Download the PDF instead.

frkrousrgksi
model # AMP 100/6 model # AMP 50/12 multi-zone amplifiers

Low Impedance Design.
Each Elura amL plifier channel is stable down to 4 ohms. This design allows for a pair of 8-ohm speakers to be connecteF d to each channel. This feature is ideal for la(rger areas ( ) requiring more coverage.

LEVEL

LINE IN

LINE IN FR LP

4/8 NORMAL

L
(L) +

R BRIDGED
IN
S-PEAK-ER + (R)

A

B HP

BUS

BRIDGED 8 ONLY

-

+

ZONE 3

Specifications.

AMP 100/6
Output Power @4: 100 Watts/Ch Output Power Bridged @8: 200 Watts/Ch Output Power (Zone 3 Only) Bridged @4: 170 Watts

AMP 50/12 Output Power @4: 50 Watts/Ch Output Power Bridged @8: 100 Watts/Ch

THD+N: @4=0.9%/ @8=1.0% Input Sensitivity: 600mV Frequency Response: 10Hz - 20kHz High Pass Filter: 85Hz - 20kHz /-3dB Low Pass Filter: 10Hz - 150Hz / -3dB Signal to Noise Ratio: -75dB Auto Turn ON: 5mV Turn OFF Delay: 8min Supply Voltage: AC230V / 50Hz
AC110V / 60Hz

Warranty.
All Elura products come with a 2 year limited liability warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled.
A product that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted without a return authorization number. The warranty is in lieu of all other warranties expressed or implied, including without limitations, any other implied warranty or fitness or merchantability for any particular purpose, all of which are expressly disclaimed. Proof of sale may be required in order to claim warranty.
www.elura.audio
MSTR

POWER

1234 56

BUS IN A

L

R

B

LINE IN

LEVEL

LINE IN

IN

OUT

4/8 FR NORMAL (L) + S-PEAKE-R + (R)

LEVEL

LINE IN

IN

OUT

4/8 FR NORMAL (L) + S-PEAKE-R + (R)

LEVEL

LINE IN FR LP

4/8 NORMAL

L (L) +

R BRIDGED
IN
S-PEAKE-R + (R)

A

B

A

B

A

B HP

BUS

HP BRIDGED 8 ONLY

-

+

BUS

HP BRIDGED 8 ONLY

-

+

BUS

BRIDGED 8 ONLY

-

+

ZONE 1

ZONE 2

ZONE 3

ZONE 3 MULTI SUB SWITCH

1 ELURA

SUBWOOFER OR BRIDGED

1

8 ohm

2 ELURA

2

SUBWOOFERS OR BRIDGED

4 ohm

model # AMP 100/6 model # AMP 50/12 multi-zone amplifiers

ON

POWER MODE

AUTO

100-120V~60Hz/220-240V~50Hz 600W

IN

OUT TRIGGER
DC 12V

FUSE T10AL/250V AVT6104-16

AMP 100/6

AMP 50/12

Overview.
Thank you for purchasing Elura Amplifier products. Elura is a high performance custom installed product engineered for movie and music enthusiasts. Each Elura product is manufactured to the highest quality standard using state of the art components and built for years of enjoyment.
Features.
· Multi-channel / multi-zone · Digital high power amplification · Low impedance · Bridgeable · Low Noise · Small chassis · Less Heat · Effiicient design · Rack mountable · Automation circuit
Contents.
· Amplifier · Rack mounting hardware · Power cord · 1/8" stereo to RCA cable · Manual

Warning.

Safety Instructions.

To reduce the risk of electric shock, 1. Read the instructions.

do not expose this product to rain or 2. Keep the instructions.

moisture. This product should not 3. Heed all warnings.

be exposed to dripping or splashing 4. Follow the instructions.

and avoid placing near any object 5. Do not use near water.

filled with water, such as a vase or 6. Clean with a dry cloth.

an aquarium.

7. Do not block ventilation slots.

Important Symbols.

8. Install in accordance to the instructions.

The lighting flash arrowhead triangu- 9. Do not install near a heat source

lar symbol is to alert the user to the

or combustible source.

presence of uninsulated `dangerous 10. Do not defeat the polarized or

voltage' within the product sufficient

grounding plug.

enough to constitute a risk of

11. Protect the power cord from

electric shock.

being crimped, cut or pinched.

12. Only attached accessories spec-

The arrowhead symbol with an

ified within the instructions.

exclamation point is to alert the user 13. Use only on lower shelves with

to the presence of an important

a stand, cart or rack product

operational or maintenance

capable of holding the weight to

instruction.

avoid injury from furniture tipping

over.

Placement / Installation.
Rack-mount ears and hardware are included with every Elura amplifier. This allows for table-top or 2U AV rack-mount installation.
Connections.
All RCA audio connections on the amplifiers are gold-plated, for superior, non-corrosive, and long-lasting performance. The removable speaker connectors offer easier wiring, faster installation, and troubleshooting. Speaker wire up to 14 AWG work best with these type of connectors. A detachable fused EIC grounded power cable defeats, noise, simplifies troubleshooting and adds protection needed.
Some stereo zones use 1/8" stereo jacks instead of RCA connections. The smaller space taken up by the stereo connection offers an in and out preamplifier connection for adding additional amplifiers, speakers or subwoofers in each zone.
Input Options.
The amplifiers offer a bus input with a loop output as well as channel-specific inputs. Installers have the option to expand the zone amplifier beyond only two channels, taking one stereo input signal and distributing it to up to a max of 6 or 12 stereo zones of audio pending the model. They also have the option of using each amplifier channel independently for multi-zone / multisource or home theater applications.

model # AMP 100/6 model # AMP 50/12 multi-zone amplifiers

AMP 100/6 Rear Panel Audio Connections

BUS IN A

L

R

B

LINE IN

LEVEL

LINE IN

IN

OUT

4/8
FR NORMAL (L) + S-PEAKE-R + (R)

LEVEL

LINE IN

IN

OUT

4/8
FR NORMAL (L) + S-PEAKE-R + (R)

LEVEL

LINE IN FR LP

4/8 NORMAL

L
(L) +

R BRIDGED
IN
S-PEAKE-R + (R)

A

B

A

B

A

B HP

BUS

HP BRIDGED 8 ONLY

-

+

BUS

HP BRIDGED 8 ONLY

-

+

BUS

BRIDGED 8 ONLY

-

+

ZONE 1

ZONE 2

ZONE 3

Automation.

ZONE 3 MULTI SUB SWITCH

1 ELURA

SUBWOOFER OR BRIDGED

1

8 ohm

2 ELURA

2

SUBWOOFERS OR BRIDGED

4 ohm

Elura amplifiers have an in/out 12VDC trigger. The flexibility to turn on the entire amplifier or trigger other devices via an audio signal offers additional control and automation options. Easily configure the amplifiers to activate with a global 12v trigger or in Auto mode using a sensitive audio sensing circuit.

When Bridging Zone 3 Only
1) Set the 4/8 Nominal Switch to Bridged 8 only 2) Set the Zone 3 Multi Sub Switch to either 8 ohm or 4 ohm.
If you are using 1 Elura architectural sub, choose 8 ohm; if you are using 2 subs, choose 4 ohm.

Audio Modes.
Elura multi-channel amplifiers are organized into stereo pairs and each pair has the option of being bridged into 1 higher wattage mono channel. Being able to bridge channels allows an installer to use more power in larger rooms or in outdoor spaces to provide the optimum sound levels and or coverage. Note, when in Bridged Mode the amplifier channel must be used only with an 8 Ohm speaker. The 100/6 Zone 3 ONLY can be connected to a 4 Ohm Load, BUT the Zone 3 multi sub switch MUST be set to Bridged 4 Ohm.

AMP 50/12 Rear Panel

L&R Speakers

L&R Speakers

use supplied 1/8" stereo mini jack to RCA jacks to connect to mult-source preamplifier zone outputs

extend and use to connect to a subwoofer in zone 2

1/8" mono jacks are used to connect 12VDC trigger inputs and outputs when power mode switch is in down position
switching to HP when connecting to a subwoofer will improve performance of main speakers

Controls.
Each stereo zone of the amplifiers can be adjusted allowing fine tuning for the zone application. Each zone offers an EQ switch. The EQ switch changes the output to the speaker. FR = Full Range, HP = High Pass and LP = Low Pass. LP is only available if RCA connections are used on that zone. Each amplifier zone with 1/8" stereo jacks in and out has FR and HP. Plan your connections by using the amplifier zone that best fits the room requirement.
Example: If you plan on connecting a Multisource preamplifier signal, speakers and a powered subwoofer, use a zone with 1/8" stereo jacks. Use the 1/8" stereo out to connect the subwoofer and select HP to send only mid and high frequencies to your speakers.

POWER

1234 56

Front Panel LEDs.
The Elura amplifiers have LEDs on the front panel to indicate the amplifier's power state and channel status. The Power LED indicates the amplifier is ON. There is a LED indicating the channel state. The LEDs can be used to identify and trouble shoot channels that are not working. If a channel is in fault mode, power down the amp, identify and fix the issue. When complete power up the amp to recheck it has been resolved.
Power ON = Blue Power OFF = Red Channel Normal = Blue Channel Fault = Red

Channel fault conditions are shortcircuit, thermal, or overload failures.


QuarkXPress(R) 9.1 (C) 2018 Retailer Web Services LLC, all rights reserved.