AutoBot Home EV Chargers - Efficient & Effortless Charging | AutoBot
Support
User Manual for AutoBot models including: 48 Amp Upgrade Home Level 2 EV Charger, 48, Amp Upgrade Home Level 2 EV Charger, Upgrade Home Level 2 EV Charger, Level 2 EV Charger, Charger
AutoBot Upgrade Home Level 2 EV Charger, 48Amp, 240V, Smart Wi-Fi and Bluetooth EVSE, Extra 2 RFID Card, Indoor/Outdoor 25-Foot Cable for All EVs, Hardwired, Gifts : Automotive
NEMA 14-50 Plug with APP User Manual (PDF) AutoBot AutoBot Level,2,Home,ev,Charger,,Portable,Electric,car,Vehicle,Ev,Charging,Stations,,NEMA,14-50,Outlet,240V,,48Amp,,Extra,2,RFID,Card,,Electric,Vehicle,Charging,Equipment,Compatible,with,All,EV,Models,B0D2HMJ7G8,B0CWGT8FRV,B0CPJFBLQ1
Upgrade NEMA 14-50 Plug with APP User Manual (PDF) AutoBot AutoBot AutoBot,Upgrade,Home,EV,Charger,Level,2,Smart,Wi-Fi,and,Bluetooth,EVSE,Extra,2,RFID,Card,40Amp,240V,Indoor/Outdoor,25-Foot,Cable,for,All,EVs，NEMA,14-50,Plug,Gifts,,
File Info : application/pdf, 24 Pages, 3.56MB
DocumentDocumentUser Manual 48A EV Charger GET FREE TECH SUPPORT Monday through Friday from 9:00 AM to 6:00 PM EST) support@autobotlife.com (+1) 888 559 3888 TABLE OF CONTENTS Important Safety Instructions 1 Overall Warnings & Cautions 1 Installation Requirements 2 Daily Maintenance 2 FCC Information 3 Product Introduction 4 Basic Interface 4 Dimensions 4 Specifications 5 Unpacking 6 Components 6 Required Tools 7 Plan The Location 8 Mount The Charger 10 NEMA Plug-in Installation 10 Hardwired Installation 13 Operate Your Charger 15 Power on 15 Register and Connect Your Charger 15 Start Charging 16 Stop Charging 16 The Digital Screen 17 Error and Warning Messages 18 Warranty And Maintenance 19 Support 20 WARNING & CAUTION Important Safety Instructions Overall Warnings & Cautions WARNING: To avoid fire, injury or death, carefully read and follow the instructions during installation, operation and maintenance. DO NOT put fingers into the electric vehicle connector. DO NOT use this product if the flexible power cord or EV cable is frayed, insulation-broken, or any other signs of damage. DO NOT use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage. DO NOT remove cover or attempt to open the enclosure because of risk of electric shock. DO NOT leave metals such as bolts, gaskets inside the device. WARNING: This device should be supervised when used around children. WARNING: This device must be grounded. WARNING: To avoid a risk of fire or electric shock, do not use this device with an extension cord. WARNING: Switch off the circuit breaker of the electrical outlet before installing this device. Installation Requirements WARNING: Disconnect electrical power prior to installing the charger. WARNING: Be sure to preview the User Manual and ensure local building and electrical codes are reviewed before installing the charger. WARNING: The charger should be installed by a qualified technician according to the User Manual and local safety regulations. CAUTION: Use appropriate protection when connecting to the main power distribution cable. 1 CAUTION: Type A, B, C or D breaker with the rating current for table should be installed in the upstream AC distribution box. CAUTION: The device shall be mounted at height between 600 mm and 1500 mm from ground. CAUTION: Install this device on a surface that can support its weight. Failure to do so can result in death, personal injury, or property damage. CAUTION: Please keep the charger in a clean area with low humidity. Not recommended to be installed in coastal environments with high humidity or high dust. Daily Maintenance CAUTION: Avoid moisture or water in the charger. If there is water or moisture ingress in the charger, it is necessary to immediately power off to avoid immediate danger, and notify the professionals to carry out maintenance before next use. CAUTION: Please use the charger properly. Do not hit or press hard on the enclosure. If it is damaged, please contact a professional technician. CAUTION: Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials. CAUTION: Do not put heavy objects on the charger to avoid danger. 2 FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur inaparticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off andon, theuser is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devicemay not cause harmful interference, and (2) this devicemust accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment. Thisequipment should be installed and operated with minimum distance 20cm between the radiator and your body. 3 Product Introduction CAUTION: Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials. Basic Interface Mounting Hole Digital Screen Dimensions 190mm Mounting Hole Charging Cable Output AC Power Input 87mm 330mm R3.5mm 210mm 3mm 4 Specifications Model Number Rated Voltage Rated Current Standard Compliance Charging Connector Charging Mode Electrical Protection Energy Meter User Interface Multi Cable Entry Connectivity Operating Temperature Operating Humidity Impact/ Ingress Protection Rating Housing Material Dimensions (mm) Net Weight TECHNICAL A08-US48A, A08-US40A 208-240V 11.5kW/48A, 9.6kW/40A SAE J1772 25 Feet Tethered SAE J1772 Mode 3 UVP, OVP, RCD, SPD, Ground Fault Protection OCP, OTP, Control Pilot Fault Protection On-board Device +/- 1% Accuracy FEATURES Digital Screen Bottom Side NETWORK 2.4G Wi-Fi, Bluetooth ENVIRONMENT -22°F - 122°F (-30°C - 50°C) Up to RH 95%, non-condensing Type 3R PHYSICAL PC with Anti-UV Treatment 87*190*330 (D*W*H) c. 4.8kg 5 Unpacking Components Make sure that all parts are delivered. Check the packaging for the following parts AutoBot charger Electric Vehicle AC Charger User Manual User Manual Screws (5 x 40 mm) Wall anchors Screw plug RFID cards Installation template 6 Required Tools Tools required before installing the charger, gather the following tools: Wire stripper Adjustable wrench Voltmeter or digital multi-meter Level Pencil Electric drill Phillips head screwdriver 7 Plan The Location WARNING: In areas with frequent thunderstorms, add surge protection at the service panel for all circuits. Ensure all power and ground connections, especially those at the breaker and bus bar, are clean and tight. CAUTION: Not recommended to be installed in coastal environments with high humidity or high dust. Before installation, check the site for appropriate mounting location and electrical capacity. 1. Choose a mounting location that allows the charging cable to reach the car's charging port while still providing slack. 2. The device must be anchored into mounting such as 80mm x 130mm stud or a solid wall. 3. The device shall be mounted at height between 600 mm and 1500 mm from ground. 4. Ensure there is Wi-Fi signal available if you want to use the app. 5. Determine the desired charging amperage and whether the desired circuit rating requires a hardwired circuit. Choose based on the electrical capacity in the panel, the desired speed of charging, and whether the user prefers a hardwired or plug-in installation. Circuit Rating 60 A 50 A 40 A Max Load 48 A 40 A 32 A Estimated Range Per Hour (based on 16kW/100 km) Up to 45 miles/72 km Up to 38 miles/61 km Up to 30 miles/48 km 8 Plug-in No Yes Yes Hardwire Yes Yes Yes 6. Ensure the electrical panel supports a 240V dedicated circuit with a new, dedicated, and non-GFCI two-pole circuit breaker, in accordance with local codes and ordinances. 7. The recommended installation height is between 51 and 59 inches (130 - 150 cm). Note that the minimum installation height must be at least 19 inches (50 cm), measured from the bottom of your charger. For plug-in installations, the NEMA outlet should be located 43 and 51 inches (110 - 130 cm) from the ground adjacent to the stud where the charging station will be mounted. Plug-in Version Hardwire Version Cable length 19'' (50 cm) Outlet height recommended 43''- 51'' (110 -130 cm) Charger height recommended 51''- 59'' (130 -150 cm) 9 Mount The Charger WARNING: This device must be grounded. Disconnect electrical power prior to installing the charger. WARNING: Improper connection of the equipment-grounding conductor would result in a risk of electric shock. Check with a qualified electrician or serviceman if you are not sure whether the product is properly grounded. Do not modify the plug provided with the product if it doesn't fit the outlet, have a proper outlet installed by a qualified electrician. CAUTION: Use appropriate protection when connecting to the main power distribution cable NEMA Plug-in Installation If you already have a NEMA outlet, ensure that: It complies with local electrical codes. It has a designated circuit breaker and electrical wiring that are dimensioned appropriately. When installing a NEMA outlet, be sure the ground pin is facing up as shown in the diagram. Important Recommendations Ensure you have the correct permits for this electrical installation. Keep in mind that the power supply cable length is about 19 inches (50 cm). Ensure the electrical panel supports a 240V dedicated circuit with a new, dedicated two pole circuit breaker. 10 120V 240V 120V NEUTRAL X Y GROUND NEMA 14-50R 1. Remove the faceplate and the wire cover from the 2. Hold the included installation template to the wall. Mark the location of the holes. Ensure that the placement of the NEMA outlet and your charger will allow for an adequate connection of the 19" (50 cm) NEMA cable. 3. Drill 2 holes with a diameter of 12 mm and a depth of 57 mm. 4. Insert 2 wall anchors into the mounting holes. Then drill one screw into the top-most mounting hole, leaving a 5 mm gap to hang the charger on. 5mm 215mm 5. Position the charger to align with the holes and hang it on the protruding screw using the notch on the back of the charger. 6. Drive the remaining screw into the mounting hole to secure the charger. Do not over-tighten the screw. 11 7. Attach the screw plug to cover the bottom screw. 8. Place the wire cover over the exposed wiring. 9. Insert the four corner screws to secure your charger cover. 10. Snap the faceplate onto the charger. 12 Hardwired Installation 1. Remove the faceplate and the wire cover from the 2. Hold the included installation template to the wall. Mark the location of the holes. Ensure that the placement of the NEMA outlet and your charger will allow for an adequate connection of the 19" (50 cm) NEMA cable. 3. Drill 2 holes with a diameter of 12 mm and a depth of 57 mm. 4. Insert 2 wall anchors into the mounting holes. Then drill one screw into the top-most mounting hole, leaving a 5 mm gap to hang the charger on. 5mm 215mm 5. Position the charger to align with the holes and hang it on the protruding screw using the notch on the back of the charger. 6. Drive the remaining screw into the mounting hole to secure the charger. Do not over-tighten the screw. 13 7. Attach the screw plug to cover the bottom screw. 8. Feed the power supply wires through the bottom port with enough length to easily connect the wires to the terminals. 9. Use copper conductors with the maximum wire size of 6 AWG (16 mm²). 10. Strip the wires to 1/2" (12 mm), insert the wires per the diagram and tighten each connector screw to 2.4 N.m. using a torque screwdriver. L1 L2 PE PE L2 L1 11. Place the wire cover over the exposed wiring. L1 L2 PE 12. Insert the four corner screws to secure your charger cover. 13. Snap the faceplate onto the charger. 14 Operate Your Charger WARNING: This device should be supervised when used around children. CAUTION: Please use the charger properly. Do not hit or press hard on the enclosure. If the case is damaged, please contact a professional technician. CAUTION: Do not put heavy objects on the charger to avoid danger. With your charger powered and connected to your EV, you can charge your EV with the provided RFID cards. If you want to fully access your charger functions and control your charger remotely, however, you will need to download the AutoBot EV app. Power On Once all electrical connections have been safely made, switch on the power to the circuit from the circuit breaker. If you have installed a NEMA plug-in model, insert the NEMA plug in the receptacle. The charger LED screen should light up. Register and Connect Your Charger 1. Download the AutoBot EV app to your mobile device from the Google Play or Apple App Store. Download on the App Store Get it on Google Play 15 AutoBot EV app 2. Open the app, sign in or create an account with your email. You will need to verify your account with a valid email address. 3. At the top right corner of the home screen, tap +. 4. Choose the serial number (SN) for your charger. This information can be found on the side of the charger. Start Charging CAUTION: Please keep your RFID cards properly to avoid unnecessary loss. 1. Plug the connector into your EV charging port. 2. If you are using the app, tap "Start Charging" on the app or swipe the RFID card on the RFID reader. If you've selected the Plug & Charge Mode, charging starts automatically. Stop Charging 1. If you are using the app, tap Pause Charging on the app or swipe the RFID card on the RFID reader once more. 2. Carefully remove the connector from EV. 16 The Digital Screen Display Status Description Available * Plug & Charge mode * Not connected to EV * App mode or RFID Card mode * Not connected to EV Charging * Charging in progress * Display voltage, current, and charging energy (kWh) in turn Charging ended * Charging ended * Display charging energy (kWh) 17 Error and Warning Messages Error Code 0001 0002 0004 0008 0016 0032 0128 0256 0512 1024 Status Off Ground RCD Abnormal Over Current Protection Over Voltage Protection Under Voltage Protection Energy Meter Fault Control Pilot Fault Over Temperature Protection Ground Fault Ground Self-Test Description Auto Recover Auto Recover Auto Recover Auto Recover Auto Recover Contact Customer Service Auto Recover Auto Recover Auto Recover Auto Recover 18 Warranty And Maintenance · The warranty period for this charger is one year. · During the warranty period for any malfunction under normal use according to the User Manual and Service Instructions (to be determined by certified maintenance technicians of sellers), the product shall be repaired free of charge. Except for the following situations, the charger shall be subject to the above warranty terms: 1. The warranty certificate cannot be provided or the contents of the warranty certificate are modified or inconsistent with the label indication of the repaired product. 2. Those who are unable to provide valid proof of purchase. 3. Those who exceed the manufacturer's specified warranty period. 4. Those who damage the product due to not following the product service instruction for use, maintenance and storage. 5. Damage or malfunction caused by external object entering. 6. Unauthorized repair, disassembly or modification. 7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire, flood, etc.). 8. Malfunction and damage caused by other unavoidable external factors. Malfunction and damage caused by improper use of equipment, such as water or other solutions entering into the equipment. Malfunction and damage caused by the grid power supply and voltage which is not specified for use with the charger equipment. The above guarantees shall be made solely, and no other express or implied warranties shall be made (including the implied warranties of merchant ability, particular and applicable reasonableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the Company shall not be responsible for any special, incidental or consequential damages. 19 Support Need technical support? Contact AutoBot customer service Monday through Friday from 9:00 AM to 6:00 PM EST) : Tel: (+1) 888 559 3888 Email: support@autobotlife.com Website: https://autobotlife.com/pages/support 20 www.autobotlife.com GET FREE TECH SUPPORT Monday through Friday from 9:00 AM to 6:00 PM EST) support@autobotlife.com (+1) 888 559 3888