MF79U Quick Start Guide

Getting to Know Your Device

Appearance

The following figure is for your reference only.

Device Diagram: A USB modem-like device is shown with numbered callouts pointing to its components.

• 1. Device cap: Covers the USB connector.
• 2. Front cover: Houses the SIM and microSD card slots.
• 3. Light Indicator: Shows device status.
• 4. External antenna connectors: For optional external antennas.
• 5. Reset hole: Press and hold for about 3 seconds to restore your device to factory settings.
• 6. micro-SIM card slot: For inserting a micro-SIM card.
• 7. microSDHC™ card slot: For inserting a microSDHC card.
• 8. USB connector: Connects to a computer or power source.

Indicator Light

NOTE: The Micro SDHC logo is a trademark of SD-3C, LLC.

Connection Scenarios

The device uses your micro-SIM card to access the Internet. It allows multiple clients to surf on the Internet at the same time.

Diagram: A tower symbol with signal waves connects to the USB modem, which is then shown connected to multiple client devices (laptops, desktop PC).

NOTE: With other accessories, such as a mobile power bank or car power adapter, you can supply power to your device and use it anywhere and anytime.

Installing Your Device

1. Open the front cover.

   (Diagram: Device with cap removed, arrow indicating opening front cover.)

2. Install a micro-SIM card to the micro-SIM card slot.

   (Diagram: Device with front cover open, arrow showing micro-SIM insertion.)

   WARNING! Your modem does not support standard SIM cards and nano-SIM cards. To avoid damage to the modem, do not use those cards or any card holders.

3. Install a microSDHC card to the microSDHC card slot.

   (Diagram: Device with front cover open, arrow showing microSDHC insertion.)

4. Close the front cover.

   (Diagram: Device with front cover closed, arrow indicating closing.)

Connecting to Your Device

Using USB Connector

Insert the device into your computer's USB port securely. The operating system automatically detects and identifies your device and starts the installation wizard.

NOTE: If the system does not automatically launch installation, you can click the device installation icon in My Computer > ZTEMODEM to install the software. The 4G Mobile Hotspot configuration page will open automatically, and then your computer will connect to your device successfully.

Using Wi-Fi

1. Supply power to your device by connecting to your computer or using other accessories.
2. Ensure that your computer or other client devices have enabled Wi-Fi, and search for available wireless networks.
3. Select the Wi-Fi name (SSID) of your device, and click Connect.
4. Enter the Wi-Fi password if necessary, and click OK.
5. Wait until the client device is connected to your device successfully.

NOTE: Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless networks. If you use a computer, you need to set your computer to obtain an IP address automatically.

NOTE: Refer to the chapter "Getting to Know the Wi-Fi SSID and Password" to get the default Wi-Fi SSID and password.

Getting to Know the Wi-Fi SSID and Password

You can view the label on the package to get the default Wi-Fi SSID and password.

Logging in to the 4G Mobile Hotspot Configuration Page

1. Ensure that the connection between your device and the client device is correct.
2. Launch the Internet browser and enter http://192.168.8.1 or http://ufi.ztedevice.com in the address bar.
3. Enter the password to log in to the 4G Mobile Hotspot configuration page.

NOTE: View the label on the package to get the default password.

Changing the Wi-Fi SSID or Password

1. Log in to the 4G Mobile Hotspot configuration page.
2. Select Wi-Fi Settings > Main SSID.
3. Change the Network Name (SSID) or the Password.
4. Click Apply.

Accessing the Internet

After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual. The default mode is Automatic.

Configuring Your PC

NOTES:

• To change the current connection setting, please disconnect from the Internet first.
• To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page.

The following procedure describes how to configure the Internet Protocol in Windows for your Wi-Fi connection.

1. Right-click Network and select Properties.
2. Select Change adapter settings.
3. Right-click Wireless Network Connection and select Properties.
4. Select Internet Protocol Version 4 (TCP/IPv4), and click Properties.
5. Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK.

Warning and Notice

To the Users

• If inadequately shielded, some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary.
• Operating the device may interfere with medical instruments such as hearing aids and pacemakers. Always keep the device more than 20 centimeters away from such medical instruments when your device is powered on. Power off the device if necessary. Consult a physician or the manufacturers of medical instruments before using the device if necessary.
• Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary.
• Do not use electronic transmission devices in aircraft, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions.
• Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be affected.
• Do not use the device in an enclosed environment or where heat dissipation is poor. Prolonged work in such space may cause excessive heat and raise ambient temperature, which may lead to automatic shutdown of the device for your safety. In the case of such an event, cool the device in a well-ventilated place before turning on for normal use.
• Keep the device out of the reach of small children. The device may cause an injury if used as a toy.
• When the device is operating, do not touch the metallic parts. Failing to do so may cause burns.
• Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals.
• Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected.
• The device is not waterproof. Keep the device dry and store it in a shady and cool place.
• Do not use the device immediately after a sudden temperature change, because dew may be generated inside and outside the device. Do not use it until it becomes dry.
• Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged.
• Only qualified personnel can dismantle and repair the device.
• An operating temperature between -10°C and +55°C and humidity between 5% and 95% are recommended.

Limited Warranty

This warranty does not apply to defects or errors in the product caused by:

1. Reasonable abrasion.
2. End users' failure to follow ZTE's installation, operation or maintenance instructions or procedures.
3. End users' mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product.
4. Modifications or repairs not provided by ZTE or a ZTE-certified individual.
5. Power failures, surges, fire, flood, accidents, and actions of third parties or other events outside ZTE's reasonable control.
6. Usage of third-party products or usage in conjunction with third-party products if such defects are due to the combined usage.
7. Any other cause beyond the range of normal usage intended for the product.

End users have no right to reject or return the product, or receive a refund for the product from ZTE under the above-mentioned situations.

This warranty is end users' sole remedy and ZTE's sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law.

Limitation of Liability

ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost.

LEGAL INFORMATION

Copyright © 2020 ZTE CORPORATION. All rights reserved.

No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation.

The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice.

Version No.: R1.0

Edition Time: March, 2020

Troubleshooting

Getting More Help

• Sending an email to Customer.care@te.eg
• Visiting www.te.eg
• Visiting we Stores
• Calling 111 or 01555000111

Contact Information

ZTE CORPORATION

NO. 55, Hi-tech Road South, Shenzhen,

P.R.China

Postcode: 518057