Oct 30, 2023 · : ATTACK SHARK. Test Model ................................... : X3 ... : X3, X2, R1, X5, X6, X11, R2, G6, X18, R3. Hardware Version. : G9 ...
Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E RADIO TEST REPORT For Guangzhou Junxingcheng Electronic Technology Co.,Ltd. Wireless mouse Test Model: X3 Additional Model No. : X2, R1, X5, X6, X11, R2, G6, X18, R3 Prepared for Address : Guangzhou Junxingcheng Electronic Technology Co.,Ltd. : Rm.201, Factory C, NO.15, Wenyong Rd. Xindun Village, Xintang Town, Zengcheng Dist. Guangzhou, China Prepared by Address Tel Fax Web Mail : Shenzhen AOCE Electronic Technology Service Co., Ltd : Room 202, 2nd Floor, No.12th Building of Xinhe Tongfuyu Industrial Park, Fuhai Street, Baoan District, Shenzhen, Guangdong, China : (86)755-85277785 : (86)755-23705230 : Http://www.aoc-cert.com : postmaster@aoc-cert.com Date of receipt of test sample : Number of tested samples : Serial number : Date of Test : Date of Report : October 23, 2023 1 Prototype October 23, 2023~October 30, 2023 October 30, 2023 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 1 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E RADIO TEST REPORT MIC Notice No.88 Appendix No. 43 Second-Generation Low-Power Data Communication System/Wireless LAN System Report Reference No. ............... : AOC231024105E Date of Issue................................. : October 30, 2023 Testing Laboratory Name ......... : Shenzhen AOCE Electronic Technology Service Co., Ltd Address......................................... : Room 202, 2nd Floor, No.12th Building of Xinhe Tongfuyu Industrial Park, Fuhai Street, Baoan District, Shenzhen, Guangdong, China Testing Location/ Procedure ........ : Full application of Harmonised standards Partial application of Harmonised standards Other standard testing method Applicant's Name ....................... : Guangzhou Junxingcheng Electronic Technology Co.,Ltd. Address......................................... : Rm.201, Factory C, NO.15, Wenyong Rd. Xindun Village, Xintang Town, Zengcheng Dist. Guangzhou, China Test Specification Standard........................................ : MIC Notice No.88 Appendix No.43 Test Report Form No. ................ : AOCEMC-1.0 TRF Originator............................. : Shenzhen AOCE Electronic Technology Service Co., Ltd Master TRF .................................. : Dated 2015-06 Shenzhen AOCE Electronic Technology Service Co., Ltd All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen AOCE Electronic Technology Service Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen AOCE Electronic Technology Service Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test Item Description................. : Wireless mouse Trade Mark................................... : ATTACK SHARK Test Model ................................... : X3 Ratings.......................................... : DC 3.7V by rechargeable lithium-ion battery, and recharged by DC 5V 1A. Result .......................................... : Positive Compiled by: Supervised by: Approved by: Johnson Wang/ Administrators Joey Liu/ Technique principal Murry Yu/ Manager This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 2 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E RADIO -- TEST REPORT Test Report No. : AOC231024105E October 30, 2023 Date of issue Test Model............................... : X3 EUT......................................... : Wireless mouse Applicant............................... Address.................................. Telephone............................... Fax.......................................... : Guangzhou Junxingcheng Electronic Technology Co.,Ltd. : Rm.201, Factory C, NO.15, Wenyong Rd. Xindun Village, Xintang Town, Zengcheng Dist. Guangzhou, China : / : / Manufacturer........................ Address................................... Telephone............................... Fax.......................................... : Guangzhou Junxingcheng Electronic Technology Co.,Ltd. : Rm.201, Factory C, NO.15, Wenyong Rd. Xindun Village, Xintang Town, Zengcheng Dist. Guangzhou, China : / : / Factory................................... Address................................... Telephone............................... Fax.......................................... : Guangzhou Junxingcheng Electronic Technology Co.,Ltd. : Rm.201, Factory C, NO.15, Wenyong Rd. Xindun Village, Xintang Town, Zengcheng Dist. Guangzhou, China : / : / Test Result Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 3 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E TABLE OF CONTENTS 1. GENERAL INFORMATION .................................................................................................................................. 5 1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................... 5 1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS ............................................................................................. 5 1.3. EXTERNAL I/O CABLE .......................................................................................................................................... 5 1.5. TEST CONDITIONS................................................................................................................................................. 5 1.6. FREQUENCY OF CHANNELS................................................................................................................................... 5 2. TEST METHODOLOGY ........................................................................................................................................ 6 2.1. EUT EXERCISE ..................................................................................................................................................... 6 2.2. MEASUREMENT UNCERTAINTY ............................................................................................................................ 6 2.3. TABLE FOR PARAMETERS OF TEST SOFTWARE SETTING ....................................................................................... 6 2.4. DESCRIPTION OF TEST MODES.............................................................................................................................. 6 2.5. TEST VOLTAGE ..................................................................................................................................................... 7 3. SYSTEM TEST CONFIGURATION ..................................................................................................................... 8 3.1. JUSTIFICATION ...................................................................................................................................................... 8 3.2. EUT EXERCISE SOFTWARE................................................................................................................................... 8 3.3. SPECIAL ACCESSORIES ......................................................................................................................................... 8 3.4. BLOCK DIAGRAM/SCHEMATICS ............................................................................................................................ 8 3.5. EQUIPMENT MODIFICATIONS ................................................................................................................................ 8 4. SUMMARY OF TEST RESULTS........................................................................................................................... 9 5. TEST RESULT ....................................................................................................................................................... 10 5.1. ANTENNA POWER ............................................................................................................................................... 10 5.2. FREQUENCY TOLERANCE.................................................................................................................................... 12 5.3. OCCUPIED FREQUENCY BANDWIDTH.................................................................................................................. 14 5.4. SPREAD BANDWIDTH.......................................................................................................................................... 15 5.5. TRANSMITTER SPURIOUS EMISSIONS (CONDUCTED) ........................................................................................... 16 5.6. CARRIER SENSING FUNCTION .............................................................................................................................. 17 5.7. INTERFERENCE PREVENTION FUNCTION .............................................................................................................. 18 5.8. SECONDARY RADIATED EMISSIONS .................................................................................................................... 19 6. LIST OF MEASURING EQUIPMENTS.............................................................................................................. 20 7. TEST SETUP PHOTOGRAPHS........................................................................................................................... 21 8. EUT EXTERIOR AND INTERIOR PHOTOGRAPHS...................................................................................... 21 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 4 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 1. GENERAL INFORMATION 1.1. Description of Device (EUT) EUT : Wireless mouse Test Model : X3 Model No. List : X3, X2, R1, X5, X6, X11, R2, G6, X18, R3 Hardware Version : G9-BK3633+3395 Software Version : V02 BLE Frequency Range : 2402-2480MHz for BLE Channel Number : 40 channels for BLE(DTS) Declared Antenna Power : 1.5mW Modulation Technology : GFSK Data Rate : 1Mbps Antenna Description : PCB antenna, -0.71dBi 1.2. Host System Configuration List and Details Manufacturer -- Description -- Model -- Serial Number -- Certificate -- 1.3. External I/O Cable I/O Port Description -- Quantity -- Cable -- 1.5. Test Conditions Temperature Range : Humidity Range : Pressure Range : 21-25 45-85% 86-107kPa 1.6. Frequency of Channels BLE (DTS) Channel 0 1 2 ------19 Frequency(MHz) 2402 2404 2406 ------2440 Channel --------38 39 Frequency(MHz) --------- 2478 2480 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 5 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 2. TEST METHODOLOGY 2.1. EUT Exercise The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of MIC Notice No.88 Appendix No. 43. 2.2. Measurement Uncertainty Test Item MU Remark Bandwidth : +/-0.2E-6 / Antenna Power : +/-0.33dB / Frequency Tolerance : +/-0.3E-6 / Conducted spurious emission : +/-0.13dB / DC Power : +/-1% / (1). This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. 2.3. Table for Parameters of Test Software Setting During testing, Channel & Power Controlling Software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product. Power Parameters: Test Software Version RF TestTool Frequency 2402MHz 2440MHz 2480MHz BLE (DTS) Default Default Default 2.4. Description of Test Modes Mode BLE (DTS) Tested mode, channel, and data rate information Preliminary Test Data Rate (Mbps) Final Test Data Rate (Mbps) (see Note) Channel 1 1 Low: CH0 1 1 Middle: CH19 1 1 High: CH39 Frequency (MHz) 2402 2440 2480 Note: According exploratory test, EUT will have maximum output power in those data rate, so those data rate were used for all test. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 6 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 2.5. Test Voltage POWER SUPPLY VOLTAGE FLUCTUATION TEST Environment Input Voltage (DC) -10% Normal +10% DC 3.33V DC 3.7V DC 4.1V Note: As normal use, the EUT is powed by DC 3.7V from battery. The DC 3.7V power was converted to DC 3.0V and supplied to RF module (controlled by the SOT-23, U3, U4). Voltage Variation (%) = (Output high or Low Voltage - Output Normal Voltage)/ Output Normal Voltage* 100 During the input supply voltage to the EUT from the external power source is varied by +/10%, if output voltage had been confirmed that the fluctuation of power supply to the RF circuit of EUT (excluding power source) is equal to or less than +/-1%. Exempt extremely high and low supply voltage condition test, EUT only operated in normal voltage to test all regulations. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 7 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . 3. SYSTEM TEST CONFIGURATION Report No.: AOC231024105E 3.1. Justification The system was configured for testing in engineering mode. 3.2. EUT Exercise Software N/A. 3.3. Special Accessories N/A. 3.4. Block Diagram/Schematics Please refer to the related document. 3.5. Equipment Modifications Shenzhen AOCE Electronic Technology Service Co., Ltd has not done any modification on the EUT. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 8 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . 4. SUMMARY OF TEST RESULTS Report No.: AOC231024105E MIC Notice No.88 Appendix No.43 Article 2 Paragraph 1 Item 19 Clause Description of Test (Transmitter Parameters) Result 6 Antenna Power PASS 6 Tolerances for Antenna Power PASS 3 Frequency Tolerance PASS 4 Transmission Rate PASS 4 Occupied Frequency Bandwidth PASS 4 Spread Bandwidth PASS 13 Dwell Time N/A 5 Spurious Emissions PASS Transmission Antenna Gain 10 N/A (EIRP Antenna Power) Transmission Radiated Angle Width 11 N/A (3dB Beam width) 12 Interference prevention function PASS 8 Carrier Sensing function N/A Receiver Parameters 7 Secondary Radiated Emissions PASS Note: (1) N/A is an abbreviation for Not Applicable. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 9 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5. TEST RESULT 5.1. Antenna Power 5.1.1. Standard Applicable Type DTS OFDM OBW<26MHz, DS OFDM OBW 26-38MHz Tolerance Limit 10mW 10mW/MHz 5mW/MHz +20%,-80% Modulation System DS, OFDM FH, DS-FH FH-OFDM Other than the above Upper Limit of EIRP for Modulation Systems Frequency band used Antenna power (max) EIRP (max) Omnidirectional case Directional case 2,400-2,483.5 MHz 10 mW/MHz 12.14 dBm/MHz 22.14 dBm/MHz 2,400-2,483.5 MHz 3 mW/MHz 6.91 dBm/MHz 16.91 dBm/MHz Excluding 2,427-2,470.75 MHz 10 mW/MHz 12.14 dBm/MHz 22.14 dBm/MHz 2,400-2,483.5 MHz 10 mW/MHz 12.14 dBm 22.14 dBm 5.1.2. Measuring Instruments Please refer to section 6 of equipments list in this report. 5.1.2. Test Procedures a. EUT have transmitted continuous maximum power b. Antenna Power Error is definition that actual measure antenna power tolerance between +20% to -80% power range that base on manufacturer declare the conducted power density. 5.1.3. Test Setup 5.1.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 10 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.1.5. Test Result Temperature Test Engineer 22.6 Dave Luo Mode BLE (DTS) CH CH0 CH19 CH39 Declared Antenna Power (mW) 1.50 1.50 1.50 Humidity Test Voltage 51.5% Normal Voltage Result (mW) 1.35 1.36 1.42 Tolerance Limit -10.00% -9.33% -5.33% +20%,-80% +20%,-80% +20%,-80% This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 11 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.2. Frequency Tolerance 5.2.1. Standard Applicable Tolerance of frequency shall be ±50ppm. 5.2.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable attenuator, set the Spectrum Analyzer as below: Centre Frequency: The center frequency of the channel under test. Resolution BW: 10 KHz. Video BW: 10 KHz. Span: 1MHz. Detector: Peak. Trace Mode: Max Hold. Alternative method: Frequency: Test Frequency Span 2 times channel bandwidth RBW 100 kHz (Modulation ON), VBW 100 kHz (Modulation ON), Sweep Time Auto Detector mode Positive peak Indication mode Max hold c. When the trace is complete, find the peak value of the power envelope and record. 5.2.3. Test Setup Layout This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 12 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.2.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Temperature 22.5 Humidity Test Engineer Dave Luo Test Voltage 51.7% Normal Voltage 5.2.5. Test Result See the Appendix test data. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 13 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.3. Occupied Frequency Bandwidth 5.3.1. Standard Applicable Permissible value for occupied bandwidth using the FH system, a hybrid system combining DS and FH systems, or a hybrid system combining FH and OFDM systems shall be 83.5 MHz or less, while necessary bandwidth (minimum occupied bandwidth sufficient to ensure information transmission of required quality at a required transmission rate for the system used under specified conditions for a given emission type) using a system other than any of the above shall be 26 MHz or less. 5.3.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable attenuator, set the Spectrum Analyzer as below: Centre Frequency: The centre frequency of the channel under test. RBW/VBW= 100 KHz/300KHz Span: Wide enough to cover the complete power envelope of the signal of the EUT. Sweep mode: Continuous sweeping. Detector: Peak. Trace Mode: Max Hold. c. When the trace is complete, measure the occupied bandwidth (99% bandwidth) with spectrum analyzer's bandwidth measure function. 5.3.3. Test Setup Layout 5.3.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Temperature 22.5 Humidity Test Engineer Dave Luo Test Voltage 51.7% Normal Voltage 5.3.5. Test Result of 99% Spectrum Bandwidth See the Appendix test data. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 14 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.4. Spread Bandwidth 5.4.1. Standard Applicable In spread spectrum systems, spread bandwidth (which refers to a frequency bandwidth with an upper limit and lower limit such that each of the mean powers radiated above the upper frequency limit and below the lower frequency limit is equal to 5 % of the total mean power radiated; this also applies hereafter) shall be 500 kHz or more. 5.4.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable attenuator, set the Spectrum Analyzer as below: Centre Frequency: The centre frequency of the channel under test. RBW/VBW= 30 KHz/100KHz Span: Wide enough to cover the complete power envelope of the signal of the EUT. Detector: Peak. Trace Mode: Max Hold. c. When the trace is complete, measure the occupied bandwidth (90% bandwidth) with spectrum analyzer's bandwidth measure function. 5.4.3. Test Setup Layout 5.4.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. 5.4.5. Test Result of 90% Occupied Bandwidth. Temperature Test Engineer 22.5 Dave Luo Humidity Test Voltage See the Appendix test data. 51.7% Normal Voltage This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 15 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.5. Transmitter Spurious Emissions (conducted) 5.5.1. Standard Applicable Permissible mean power of spurious emission of each frequency supplied to a feeder, that is, mean power of spurious emission in the 1 MHz bandwidth at frequency f other than frequency band used shall be as follows: a. 2,387MHz f 2,400MHz and 2,483.5MHz < f 2,496.5MHz 25 W or less b. 2,387MHz > f and 2,496.5MHz < f 2.5 W or less 5.5.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable attenuator, set the Spectrum Analyzer as below: Below 1GHz: RBW/VBW= 100 KHz/ 100KHz Above 1GHz: RBW/VBW= 1MHz / 1MHz. Detector: Peak. Trace Mode: Max Hold. c. All the emissions from 30MHz to 13GHz were measured and record. 5.5.3. Test Setup Layout 5.5.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Temperature 22.6 Humidity Test Engineer Dave Luo Test Voltage 51.5% Normal Voltage 5.5.5. Test Results See the Appendix test data. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 16 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.6. Carrier sensing function 5.6.1. Standard Applicable Item Carrier Sense Limits Good EUT stop RF transmission signal after carrier inject to EUT. (On 22.79+Gr-20*log (f)[dBm] (Gr: dBi; f: MHz) or 100mV/m) 5.6.2. Instruments Setting The following table is the setting of spectrum analyzer and receiver. Spectrum Parameter Setting Attenuation Auto RB / VB 1 MHz Span 0 MHz Sweep Continuous Detector Peak Trigger mode Video 5.6.3. Test Procedures 1. SSG adjusted the frequency as same as the EUT transmitted signal and emitted the absence of modulation from SSG and power level is (On 22.79+Gr-20*log(f)[dBm] (Gr: dBi; f: MHz). Then turn off the RF signal of SSG. 2. EUT have transmitted the maximum modulation signal and fixed channelize. 3. Setting of SA is following as: RB: 1MHz / VB: 1MHz / SPAN: 50MHz / AT: 10dB /Ref: 0dBm / Sweep time: Auto / Sweep Mode: Continuous sweep / Detect mode: Positive peak. 4. SSG RF Signal On. 5. EUT shall be stop the transmitted any signal and SSG RF Signal Off. Then EUT will be continuous transmitted signal. 5.6.4. Test Setup Layout 5.6.5. EUT Operation during Test The EUT was programmed to be in normal transmitting mode. 5.6.6. Test Result Not Applicable. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 17 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.7. Interference prevention function 5.7.1. Standard Applicable Item Identification code Limits 48 bits 5.7.2. Measuring ID Code Software PC with NetTool MAC IP List Setting MAC Scan 5.7.3. Test Procedures 1. In the case that the EUT has the function of automatically transmitting the identification code: a. Transmit the predetermined identification codes from EUT. b. Check the transmitted identification codes with the demodulator. 2. In the case of receiving the identification code: a. Transmit the predetermined identification codes from the counterpart. b . Check if communication is normal. c. Transmit the other signals than predetermined ID codes from the counterpart. d. check if the EUT stops the transmission, or if it displays that identification codes are different from the predetermined ones. 5.7.4. Test Setup Layout 5.7.5. EUT Operation during Test The EUT was programmed to be in normal transmitting mode. 5.7.6. Test Result EUT ID DE:38:B6:46:4A:4B Performance index Good This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 18 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5.8. Secondary Radiated Emissions 5.8.1. Standard Applicable The limit on secondary emissions radiated from the receiving equipment within which the function of other radio equipment will not be impaired shall be, in terms of the power of a dummy antenna circuit that has the same electrical constant as the receiving antenna, 4nW or less at a frequency below 1 GHz and 20 nW or less at a frequency of 1 GHz or higher as measured using the circuit 5.8.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable attenuator, set the Spectrum Analyzer as below: Resolution BW: 100 KHz for frequency below 1GHz and 1MHz for frequency above 1GHz Video BW: 100 KHz for frequency below 1GHz and 1MHz for frequency above 1GHz Detector: Peak. Trace Mode: Max Hold. c. All the emissions from 30MHz to 13GHz were measured and record. 5.8.3. Test Setup 5.8.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Temperature 22.6 Humidity Test Engineer Dave Luo Test Voltage 51.5% Normal Voltage 5.8.5. Test Results See the Appendix test data. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 19 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 6. LIST OF MEASURING EQUIPMENTS Instrument EMC Receiver Signal analyzer LISN LISN (Support Unit) RF Cable-CON ISN AC Power Source DC power Soure Temp. and Humidigy RF CChAaBmLbEer-1m RF CABLE-2m Signal Generator Oscilloscope Power meter Power sensor Manufacturer R&S Agilent MESS Tec EMCO UTIFLEX SCHAFFNER HPC GW Giant Force JYE Bao JYE Bao R&S Tektonix Agilent Agilent Model No. ESCS 30 N9020A NNB-2/16Z 3819/2NM 3102-26886-4 ISN ST08 HPA-500E GPC-6030D GTH-225-20-S RG142 RG142 SMR40 TDS380 E4419B E9301H Serial No. 100174 US44300469 99079 9703-1839 CB049 21653 HPA-9100024 C671845 MAB0103-00 CB034-1m CB035-2m 10016 B016197 MY45104495 MY41495236 Characteristics 9kHz 2.75GHz 9kHz~40GHz 9KHz-30MHz 9KHz-30MHz 9KHz-30MHz 9KHz-30MHz AC 0~300V DC 1V-60V N/A 20MHz-7GHz 20MHz-1GHz 10MHz~40GHz 400MHz/2GRS 100KHz-30GHz 9KHz-30GHz Cal Date May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 May 19, 2023 Due Date May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 May 18, 2024 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 20 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 7. TEST SETUP PHOTOGRAPHS Please refer to separated files for Test Setup Photos of the EUT. 8. EUT EXTERIOR AND INTERIOR PHOTOGRAPHS Please refer to separated files for External AND Internal photographs of the EUT. This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 21 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E Appendix for Article 2-1, Item 19 1. 99% Occupied Bandwidth Condition NVNT NVNT NVNT Antenna ANT1 ANT1 ANT1 Rate 1Mbps 1Mbps 1Mbps Frequency(MHz) 2402 2440.00 2480 Occupied Bandwidth(MHz) 1.23 1.23 1.23 Limit(MHz) <26 <26 <26 99%_Occupied_Bandwidth_NVNT_ANT1_1Mbps_2402 Result Pass Pass Pass 99%_Occupied_Bandwidth_NVNT_ANT1_1Mbps_2440 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 22 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . 99%_Occupied_Bandwidth_NVNT_ANT1_1Mbps_2480 Report No.: AOC231024105E This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 23 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . 2. Spread Bandwidth Condition NVNT NVNT NVNT Antenna ANT1 ANT1 ANT1 Rate 1Mbps 1Mbps 1Mbps Frequency(MHz) 2402 2440.00 2480 Spread_Bandwidth_NVNT_ANT1_1Mbps_2402 Report No.: AOC231024105E Spread Bandwidth(MHz) 0.83 0.82 0.82 Spread_Bandwidth_NVNT_ANT1_1Mbps_2440 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 24 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Spread_Bandwidth_NVNT_ANT1_1Mbps_2480 Report No.: AOC231024105E This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 25 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 3. Spurious Emissions Condition NVNT NVNT NVNT NVNT NVNT NVNT NVNT NVNT NVNT NVNT NVNT NVNT Antenna ANT1 ANT1 ANT1 ANT1 ANT1 ANT1 ANT1 ANT1 ANT1 ANT1 ANT1 ANT1 Rate 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps Frequency(MHz) 2402 2402 2402 2402 2440.00 2440.00 2440.00 2440.00 2480 2480 2480 2480 Frequency Area(MHz) 30.00~2387.00 2387.00~2400.00 2483.00~2496.00 2496.00~13000.00 30.00~2387.00 2387.00~2400.00 2483.00~2496.00 2496.00~13000.00 30.00~2387.00 2387.00~2400.00 2483.00~2496.00 2496.00~13000.00 Read Level(dBm) -43.83 -31.36 -50.00 -51.70 -48.75 -47.26 -45.92 -47.14 -53.63 -49.40 -39.15 -43.24 Limit(dBm) -26 -16 -16 -26 -26 -16 -16 -26 -26 -16 -16 -26 Spurious_Emissions_NVNT_ANT1_1Mbps_2402 Result Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass Pass This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 26 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Spurious_Emissions_NVNT_ANT1_1Mbps_2440 Report No.: AOC231024105E Spurious_Emissions_NVNT_ANT1_1Mbps_2480 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 27 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 4. Secondary emission of radio wave Condition NVNT NVNT NVNT NVNT NVNT NVNT Antenna ANT1 ANT1 ANT1 ANT1 ANT1 ANT1 Rate 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps 1Mbps Frequency(MHz) 2402 2402 2440.00 2440.00 2480 2480 Frequency Area(MHz) 30.00~1000.00 1000.00~13000.00 30.00~1000.00 1000.00~13000.00 30.00~1000.00 1000.00~13000.00 Read Level(dBm) -61.69 -74.49 -61.53 -74.56 -61.93 -74.93 Limit(dBm) -54 -47 -54 -47 -54 -47 Secondary_emission_of_radio_wave_NVNT_ANT1_1Mbps_2402 Result Pass Pass Pass Pass Pass Pass Secondary_emission_of_radio_wave_NVNT_ANT1_1Mbps_2440 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 28 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E Secondary_emission_of_radio_wave_NVNT_ANT1_1Mbps_2480 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 29 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Report No.: AOC231024105E 5. Frequency Tolerance Condition NVNT NVNT NVNT Antenna ANT1 ANT1 ANT1 Modulation 1Mbps 1Mbps 1Mbps Frequency (MHz) 2402 2440.00 2480 Test Frequency(MHz) 2401.998 2439.996 2479.996 Frequency Tolerance(ppm) -0.833 -1.639 -1.613 Frequency_Tolerance_NVNT_ANT1_1Mbps_2402 Limit(ppm) ±50 ±50 ±50 Result Pass Pass Pass Frequency_Tolerance_NVNT_ANT1_1Mbps_2440 This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 30 of 31 Shenzhen AOCE Electronic Technology Service Co., Ltd . Frequency_Tolerance_NVNT_ANT1_1Mbps_2480 Report No.: AOC231024105E ----------------THE END OF REPORT--------------- This report shall not be reproduced except in full, without the written approval of Shenzhen AOCE Electronic Technology Service Co., Ltd Page 31 of 31Microsoft Word 2019 Microsoft Word 2019