Moes WiFi Thermostat ECF-SOP20
User Manual
Introduction
Before using the device, please read this manual carefully. The manual contains important information about the intended use of the device. Pay special attention to the safety instructions. Keep the manual for future use. If you hand over the device to other persons, also hand over the manual.
It is important to carefully study this manual before using the sensor and ensure you understand its content. If you have any questions or doubts regarding the use of the sensor, do not hesitate to contact the seller, 1. e-shop s.r.o., via the website https://www.smart-switch.cz/.
Overview
The SOP20 is an easy-to-use, safe, and reliable temperature controller with a dual relay output. It can be used as an overheat protection and an automatic temperature regulation system for various electrical appliances, such as home cooking devices, pet breeding, incubation, seedling heat mats, terrestrial heat regulation, constant temperature cycle for heat pumps, culture fermentation, seed germination acceleration, electric radiators, electric ovens, etc.
- Plug and play design, easy to use – two steps to complete.
- Control your device from anywhere using the free Smart Life app.
- Dual relay output – Ability to connect a cooling and heating device simultaneously.
- LED display – Can display the measured temperature and set it at the same time.
- Temperature unit – Supports Celsius or Fahrenheit degrees.
- High and low temperature alarms are available.
At a Glance
The device features a main unit with a power plug and a temperature sensor probe. The main unit has an LED display and several control buttons. The power cord connects to a standard US socket. The temperature sensor probe is designed to be placed in the environment to be monitored.
Key Components:
- 1. Plug: Standard US AC socket plug.
- 2. Temperature sensor: Probe for measuring ambient temperature.
- 3. Current temperature: Displays the currently measured temperature.
- 4. Upper temperature limit: The set upper threshold for temperature control.
- 5. Lower temperature limit: The set lower threshold for temperature control.
- 6. On/Off button: Powers the device on or off.
- 7. Setting button: Used for navigating menus and adjusting settings.
- 8. Increase button: Increases the set value.
- 9. Decrease button: Decreases the set value.
- 10. Heating output socket: Socket for connecting a heating device.
- 11. Cooling socket: Socket for connecting a cooling device.
Product Description
Power Plug: Features a standard US socket panel, compliant with US standards.
Power Button: Can also be used as a WiFi pairing button.
Decrease Button: A long press (3 seconds) will mute the buzzer.
Setting Button: Allows switching between Celsius (°C) and Fahrenheit (°F) temperature units.
Specifications
- Model: SOP20
- Power supply voltage: AC100-250V, 50/60Hz
- Rated current: 10A Max.
- Temperature measurement range: -30~105 °C / -22~221 °F
- Wireless frequency: 2.4 GHz
- APP Control: Smart Life APP (Android 4.4/ iOS 8.0 or higher)
- Temperature probe type: R25=10KΩ±1% B25/85=3435K±1%
- Temperature accuracy: 1%
How to Download the Smart Life App
- Scan the QR code to download and install the Smart Life app for iOS or Android phones.
- If you cannot download the Smart Life app, search for "Smart Life" on Google Play (for Android phones) or the Apple Store (for iOS phones).
App Download Links:
- http://app.yimusmart.com/smartlife (Google Play / App Store)
How to Add Device via Quick Connection
- Open the Smart Life app and tap the '+' button in the top right corner to add a device.
- Plug the Smart Temperature Controller into an electrical outlet. Ensure your smartphone is connected to your home 2.4G Wi-Fi network. Press and hold the power button for 3-5 seconds to reset the device. The WiFi icon on the screen will flash 3 times per second when the device is ready for pairing. Select 'Socket (Wi-Fi)' and 'Confirm indicator is flashing rapidly' to add the device.
- You will be prompted to enter your Wi-Fi password. Note: This smart device only supports 2.4 GHz Wi-Fi networks. Please confirm your home network before connecting. Select your 2.4 GHz Wi-Fi network to connect your phone and the smart device.
- After successful connection, you can change the name of the smart device.
The app interface displays current temperature, set limits, and control modes. Users can monitor temperature trends, switch power, and access settings like cooling delay, temperature alarms, and calibration.
Button Operation Guide
- Turn On / Off: Press the button to display the screen; press again to turn off the socket.
- Setting Maximum Temperature:
- Setting High Temperature: Long press the setting button for 3s; the decimal point will flash. Use the setting button to select the digit position, and long press to increase or decrease the value. Press the setting button to confirm.
- Setting Minimum Temperature: Long press the setting button for 3s; the decimal point will flash. Use the setting button to select the digit position, and long press to scroll up or down. Long press the setting button for 3s to exit settings.
- C/F Switch: Press the setting button to switch between Celsius (°C) and Fahrenheit (°F).
- Buzzer On/Off: Long press the down button to turn the buzzer on or off. The status will be displayed.
- Other Functions:
- If the temperature sensor circuit is shorted or open, the controller enters a probe fault mode, closes all execution states, and the buzzer sounds. After the fault is cleared, pressing any button will silence the buzzer, and the device will return to normal operation.
- When the controller is turned off or disconnected, the mobile APP will continue to show the online status. The disconnected status will be displayed after 1-3 minutes.
Control Function Instructions
- Heating Mode: When the measured temperature PV is less than the Low Temperature Value (LV), the controller enters heating mode, turning on the HEATING output. When the measured temperature PV is greater than or equal to HV-2°C (High Temperature Value), the HEATING output switches off.
- Cooling Mode: When the measured temperature PV is greater than the High Temperature Value (HV), the controller enters cooling mode, turning on the COOLING output. When the measured temperature PV is less than or equal to LV+2°C (Low Temperature Setting Value), the COOLING output switches off.
- Normal Mode: The device is not operating when the measured temperature is between HV and LV; no specific icon is displayed. Note: Mode transitions occur after a 15-second delay. For example, with HV=26.0°C and LV=23.0°C: if PV > 26.0°C, cooling starts; if PV < 25.0°C, cooling stops; if PV < 23.0°C, heating starts; if PV > 24°C, heating stops.
- High/Low-Temperature Limit Alarm: If the measured temperature exceeds the High Temperature Alarm (AH), the buzzer will sound an alarm ('bi-bi-Bii') until the temperature drops below AH. Pressing any button will silence the buzzer. If the measured temperature falls below the Low Temperature Alarm (AL), the buzzer will sound ('bi-bi Bii') until the temperature rises above AL. Pressing any button will silence the buzzer.
Installation Recommendation
Although the installation of the device is very simple, it is recommended to entrust it to a qualified person authorized for electrical equipment installations according to local regulations (e.g., decree no. 50 § 6 in some regions, referring to a knowledgeable person).
Importer Information
Importer: 1. e-shop s.r.o. (www.smart-switch.cz)
Recycling Information
All products marked with the symbol for separate collection of waste electrical and electronic equipment (Directive WEEE 2012/19 / EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this device must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Proper disposal and recycling will help prevent potential negative impacts on the environment and human health. To find out where these collection points are located and how they operate, contact an installation technician or local authority.
[Symbol for separate collection of WEEE: A crossed-out wheelie bin with an 'X' through it.]
