Kenmore 1625 Sewing Machine Instructions

Instructions for Kenmore models including: 1625 Sewing Machine, 1625, Sewing Machine, Machine

KENMORE 1625 (01) PDF MANUAL - Manual-Hub.com

File Info : application/pdf, 50 Pages, 10.95MB

KENMORE 1625 (01)

Kenmore
INSTRUCTIONS
ZIG · ZAG SEWING MACHINE MODEL 1430/1431/1625/1641/1940/1941

59982

https://manual-hub.com/

TABLE OF CONTENTS ..............................................

, KNOWING YOUR SEWING MACHINE
Identifying Parts ................................................. Installing Machine ............................................... Converting to Free-arm Sewing ................................ Winding the Bobbin ............................................... Threading the Bobbin Case ...................................... Threading of Top Thread ........................................ USING THE CONTROLS
Adjusting Top Tension ........................................... Adjusting Bobbin Tension ....................................... Checking Tensions ................................................ Stitch Width Control ..............................................
Stitch Length Control ............................................. Reverse Stitch Control ...........................................
Special Stitch Modifier ........................................... Buttonhole Control ................................................
Special Stitch Dial ............................................ Pressure Regulator ................................................ Feed Dog Control .................................................. Sewing Light ....................................................... Needle Plates .................................................. Seam Guides ..................................................
ACCESSORIES Needles .............................................................. Needle, Thread, and Fabric Chart .............................. Presser Feet ........................................................ Buttonhole Attachment ..........................................

2, 3 4, 5
6 7 8 9
10 11 12 13 13 14 14 14 15, 16 17 18 18 19, 20 19, 20
21 22 23 24

= STARTING TO SEW ..............................................

GARMENT CONSTRUCTION STITCHES

Straight Stitching ............................................

26, 27

Zigzag Stitching ...................................................

Stretch Stitching ............................................. SPECIAL FINISHING STITCHES

28 - 30

Buttonhole Making ..........................................

31 - 34

Blind Hemming .....................................................

Satin Stitching, Appliqueing ....................................

Zipper Application .................................................

Mending ...........................................

-.................. 38

Darning ...................... -........................................

Button Sewing .....................................................

Bar Tacking ...............................

....: ..................... 39

FREE-ARM SEWING .............................................

1 CHECKING PERFORMANCE PROBLEMS ............. 41, 42

4. CARING FOR THE MACHINE
Cleaning Feed Dogs and Shuttle ............................... Oiling Under Arm Cover Plate ................................... Oiling Underside .............................................. Oiling in Face Cover Plate ........................................ Parts List .......................................................

43 44 45, 46 46 47, 48

https://manual-hub.com/

_1. _KNOWING YOUR MACHINE _

FRONT VIEW

®.

@ ®
(Flat-bed type)

https://manual-hub.com/

BACK VIEW
(Model 1430, 1940)

!625, ! 1641, 19412
only)

(-_odel 19412 only) (Flat-bed type)

https://manual-hub.com/

INSTALLING MACHINE (Free-armtype)

1. To install the machine in cabinet, position machine head on cabinet platform so that holes on bottom of machine match those on boards. Insert washers and screws
and tighten into place. (Fig. 1)
2. A separate base and cover is available to carry the machine when needed. The base must be removed when machine is used.
To install machine in carrying case, set machine into base, with word FRONT in base facing you. (Fig. 2) Place cover on machine with word

"SEARS" on handle facing you, The case slopes in the same direction of the machine. (Fig. 3)
, Push the speed control plug onto threeprong connector, Plug machine cord into any !10.!20 volt wall outlet. Turn on power by pushing light and powe_ switch. (Fig. 4)
, Spool pins are packed in accessorybox. Screw thread spool pins in place securely with a screw driver, Position nylon discs as shown.in illustration.

https://manual-hub.com/

INSTALLING MACHINE (Flat bed type)

1. Loosen the two hinge screws under holes in the rear edge of the machine bed.
2. Raise hinge pins in the cabinet or case. Slip machine head onto pins.
3. Tighten hinge screws securely.
4, Push the speed control plug onto three-prong connector under the bed plate. Lower machine head to front cabinet flap,

g Plug machine cord into any 110-120 volt wall outlet. Turn on power by pushing light and power switch.
6, Spool pins are packed in accessory box. Screw thread spool pins in place securely with a screw driver. Position nylon discs as shown in illustration.

https://manual-hub.com/

CONVERTING TO FREE-ARM SEWING

° Remove the base from the machine by pushing the release button (if applicable) and pulling the base to the left. (Fig. 1, 2)

2. To replace the base, simply slide it along the free arm to its original position. (Fig. 1)
Note: Base cannot be removed or replaced unless shuttle cover is closed.

https://manual-hub.com/

WINDING THE BOBBIN

, Release clutch by pulling hand wheel or turning clutch knob toward you as shown in Fig. 1.
, Draw thread from spool through bobbin winder tension disc as shown.
3. Pull end of thread through hole in bobbin as shown.
4. Place bobbin onto bobbin winder shaft with end of thread coming from the top of the bobbin. Push

bobbin winder latch against bobbin until it clicks, Holding onto end of thread, start machine. When bobbin is slightly filled, snip off end of thread.
5. Start machine. Wind thread until bobbin winder latch releases.
6. Push in hand wheel or tighten clutch knob to return to stitching position, Remove bobbin,

https://manual-hub.com/

THREADING THE BOBBIN CASE

1. Remove base front cover by pushing the release button on the left side. Open the shuttle cover.
2. Raise needle to its highest position by rotating hand wheel toward you.
3. To remove bobbin case from shuttle, pull open latch of bobbin case.
4. Pull bobbin case straight out of shuttle.

5. Insert bobbin into bobbin case mak-
ing sure thread is coming from bobbin as shown.

6. Pull thread through slot of case as shown.

7. Pull thread under tension spring.

8, Holding latch open, position into shuttle, and release latch. should lock into place when is released.

case Case latch

https://manual-hub.com/

THREADING OF TOP THREAD

Place thread on spool pin as shown with thread coming from the back of the spool. Draw thread through the top thread guide. Holding the spool stationary with right hand, pull the end of the thread between the tension discs as shown. Pull the spring wire loop up and past the top hook until the thread can be slipped into hook
(See Fig. 2). When the thread is released, the spring wire loop will return to position (Fig.

3) with thread in proper place. Release spool of thread and hook thread into take up lever as shown (Fig. 4). Continue to thread machine exactly as shown. Needle must always be threaded in direction as shown in Fig. 5.
Hold needle thread loosely in left hand and rotate hand wheel toward you one complete turn, Bring bobbin thread up by pulling upper thread.
9

https://manual-hub.com/

ADJUSTING

TOP TENSIONS

Probably the most important control on your machine is this one that regulates your top thread tension. It consists of discs between which the thread passes. The pressure on these discs is regulated by turning the dial. The higher the number, the tighter the tension.
There are many reasons for having to reset your tension. The best tension for one fabric may not be correct for another. The required tension depends upon the stiffness of the fabric, thickness of the fabric, numbers of layers of fabric being sewn, as well as the type of stitch you are making.
it is best to test the stitching on a scrap of the fabric you are using before starting to make a garment as shown below. Use the straight stitch function.

Upper thread too tight

Decrease Tension

Upper thread too loose

Increase Tension

https://manual-hub.com/

ADJUSTING BOBBIN TENSIONS
Bobbin tension requires adjusting less frequently than the upper thread tension. If the stitch is satisfactory but the seam is puckered, it may be necessary to loosen the tension on both the top and bottom threads. Be sure to balance them as indicated on Page 10. When adjusting the tension on the bobbin case, make slight adjustments with a screwdriver.
DECREASE TENSION

_.
INCREASE TENSION

Turn Counter Clockwise.

Turn Clockwise.

https://manual-hub.com/

CHECKING TENSIONS
The easiest way to check tensions is to sew a medium zig zag stitch on the fabric you will be using. Use the appropriate type of thread and needle. Use different colors of thread on the bobbin and upper spool.
Sew a line of zig zag stitches The bobbin thread should not snow on the top of the fabric.
Adjust the top tension if necessary to achieve the stitch balance mentioned above

UNBALANCED

BALANCED

TOP VIEW

1'3

https://manual-hub.com/

STITCH WIDTH CONTROL
This control regulates the width of the stitch you select. THE HIGHER THE NUMBER*THE WIDER THE STITCH. You may vary your zigzag stitch width by adjusting this control to the setting you desire.
This control must be on Red Dot in order to do straight stitching. Turn only the outer rim of this control to set the stitch width. The center of the control dials the special stitches the machine is capable of sewing.
STITCH LENGTH CONTROL
The stitch length control regulates the length of the stitch you select. THE HIGHER THE NUMBER-THE SHORTER THE STITCH. The number on stitch length control indicates the approximate number of stitches per inch. The stitch setting you use will be determined by the thickness of the fabric you are sewing. A IQnger_stiich setting should be used for thicker fabric or more layers of fabric. The middle range of the control is the 10-12 stitchper inch range which is the most commonly used. A basting stitch is made by using the longest possible stitch setting -6 stitches per inch. The red marking ,=,= on the control is the setting used for the shortest stitches such as in Satin Stitching.

https://manual-hub.com/

REVERSE STITCH CONTROL':

It is best to begin and end seams with a few stitches taken in reverse, This is

called back tacking. Back tacking fastens the ends of the seams firmly and

preventsrave!ing. _ :

· _ :_:

When reverse stitching is needed, turn the control clockwise and: hold_ there
dur!ng sewing, The fabric w!ll..immediately sta[t feeding backwards and seam will be fastened .....

SPECIAL STITCH MODIFIER

This control gives you the means of varying the stitches on the Special Stitch Dial, When the pointer: is turned to the Red Dot, the machine sews
forward only, When the pointer is turned to the White Dot, the forward designs are varied by the machine
sewing in a forward and reverse manner. Carefully read directions given in the next section of the book in order
to accomplish the various stitches correctly.

BUTTONHOLE CONTROL
(Model 1625 only)
This control is used in making buttonholes. Detailed instructions are given in the next section of the book.

https://manual-hub.com/

SPECIAL STITCH DIAL
There are certain types of utility stitches you will use often in your home sewing. This control enables you to just dial the stitch you need for the task at hand.
All stitches printed in red on the dial must be sewn with the Special Stitch Modifier set at the Red Dot.
To make the stitches printed in white on this dial, the Special Stitch Modifier must be set at the White Dot.
THE RED DOT SETTING

The setting illustrated above is the one used for most of your stitching. At this setting you may straight stitch, stretch stitch and make a simple zig zag stitch. As each stitch is dependent upon the settings of your other controls, carefully read the directions in the next section of the book for the various stitches.

https://manual-hub.com/

BLIND STITCH AND OVERCAST STRETCH STITCH "V"V" _ Blind hems are made by using the setting shown above with the Stitch Modifier set on the Red Dot. When the Modifier is set on the White Dot, overcast stretch stitching is made.
SPECIAL MENDING STITCH AND SMOCKING STRETCH ''"_'t_VY_00_
You will find that much of your sewing is in the mending category. For this reason you have been provided with a stitch for the repair of tears. It is accomplished with the above illustrated setting and the Modifier set at the Red Dot. When the Modifier is turned to the White Dot a Smocking Stitch results. For directions see the next section of the book.
SPECIAL BOX STITCH AND ELASTIC STRETCH .JV_L/_
The setting illustrated is used for special edge finishing and special stretch stitch for sewing elastic such as sportswear, girdles and other garments that require stretch. See next section of this book for detailed use of the stitches,
SERGING OR PINE LEAF STRETCH _j_//// Serging or pine leaf stretch is used for seam finishing on all types of fabrics. It is a stitch used in the garment industry. _It forms a good looking seam, stitching and overcasting the edges. This stitch is useful for seaming of seimwear, stretch ski pants and other types of knit sportswear. Modifier must be set on the White Dot.

https://manual-hub.com/

OTHER ADJUSTMENTS OF MACHINE IN SEWING
In addition to the obvious controls of your machine, there are other small regulators and controls to aid you in using your sewing machine.
PRESSURE REGULATOR

Push down the outer ring of the pressure regulator. This will release the pressure on the presser foot. (See above). To-increase the pressure, push down inner pin until a suitable pressure is obtained.
Insufficient pressure may cause poor feeding of the fabric, skipped stitches, or difficulty in guiding the fabric. If feed dogs or presser foot marks appear on the fabric, reduce the pressure.
When sewing multiple thickness or heavy fabric, reduce the pressure. Increase pressure when sewing lighter weight fabrics.

https://manual-hub.com/

FEED DOG CONTROL
There are a few times when you want to control the feeding of the fabric yourself. Remove the base cover from the base. Pull down the feed dog control or turn to the left as shown in Fig. 1. The feed dogs will drop. You may then determine the movement of the fabric yourself. For most of your stitching, the feed dog control should be in the up position. Whenever you raise or lower the feed dogs, be sure to have the presser foot in the up position.
SEWING LIGHT
The light and power switch shown in Fig, 1 and 2 provides the electric current for the motor as well as for the light. In order to operate the machine, this switch must be on. To turn on the light, depress the upper side of the switch. If you are interrupted while sewing and must leave the machine unattended, just turn off the switch and the machine cannot be started accidentally.
The sewing light is located inside the face cover plate as shown. To replace the bulb, turn light off, and swing the face cover plate open. Push up on the bulb slightly and turn bulb clockwise. Remove bulb from socket. Push in new bulb and turn counter-clockwise.

3
https://manual-hub.com/

NEEDLE PLATE INSERTS
(Free-arm type)
You are provided with two needle plate inserts: A. Needle plate with wide oval hole for
all zigzag stitching. B. Needle plate with round hole for
regular straight stitching and straight stretch stitch sewing.
CHANGING NEEDLE PLATE INSERTS
1. Raise needle to its highest position and raise presser foot.
2. Swing shuttle cover open.
3. Push a spring under the plate as shown to release the needle plate insert.
4. Remove needle plate insert by placing thumb under edge of plate.
5. Replace the needle plate insert positioning as shown in Fig. 3.
6. Push needle plate insert down to lock into place, Reposition the shuttle cover.

SEAM GUIDES
Seam guides are printed on either side of the needle plate to aid you in guiding your fabric, THE GUIDE LINE EXTENDING ABOVE THE RIGHT SIDE OF THE NEEDLE PLATE IS THE "ALL IMPORTANT" 5/8'" SEAM LINE.

The cornering guides are convenient

when turning a square corner 5/8"

from the fabric edge.

See next

section of this book for directions.

https://manual-hub.com/

MULTI PURPOSE NEEDLE PLATE (Flat-bed type)

This multi purpose needle plate pro-
vides a small round hole for straight
stitching and a wide oval hole for zig zag and decorative stitching.

CHANGINGMULTI PURPOSE

NEEDLE PLATE

1. Raise needle to its highest position and raise presser foot.

2. Open hand hole cover plate.

1 Remove multi purpose needle plate by placing thumb under edge of plate and lifting it up and out.

* Reverse and reposition the needle plate as shown.

. Lock it into place by fixing hand hole cover plate in position.

SEAM GUIDES
Seam guides are printed on either side of the needle plate to aid you in guiding your fabric. THE GUIDE LINE EXTENDING ABOVE THE RIGHT SIDE OF THE NEEDLE PLATE IS THE "'ALL IMPORTANT" 5/8" SEAM LINE.
The cornering guides are convenient when turning a square corner 5/8" from the fabric edge. See next section of this book for directions.

;)0

https://manual-hub.com/

ACCESSORIES
NEEDLES
Use KENMORE needles. The size of the needle should conform with the size of the thread and both should be suitable to the fabric (See next page).
Never use a bent needle or one with a blunt point.
Fig. 1. shows you the exact length of your needle. Be sure you never use one in your machine that is not this exact length.
You will find among your accessories "Q NEZI_LES",.with blue shanks. These special needles are to be used when sewing, certain knits and certain difficult synthetic fabrics. If you experience skipped stitches in any of your sewing, use -o NEEDLE",..
PLACEMENT OF NEEDLE
Raise needle bar to its highest position by turning the hand wheel toward you. Loosen the needle clamp screw. Holding the needle with the flat side away from_you, slip the needle into the needle bar. Make certain it is up as far as it can go. Tighten the needle clamp screw-with a screwdriver.
If you have a double needle for decorative stitching, it is inserted in the same manner as the single needle.

https://manual-hub.com/

NEEDLE, THREAD AND FABRIC CHART

O r)

https://manual-hub.com/

PRESSER FEET
SUPER-HIGH BAR TYPE
Simply drop the presser foot lock and slip the foot away from the presser bar. To aid you in the placement of the presser foot, the presser foot lever can raise the foot beyond the normal "'up" position. After the foot is placed on the presser bar, lift the lock as high as it will go to hold the foot securely.
SNAP-ON TYPE
Raise the presser bar to its highest position by lifting the presser foot lever. Press the toe of presser foot upward as high as it will go and foot is released.
Place the desired foot on the needle plate aligning the needle holes and lower the presser foot lever. Press down on presse! foot thumb screw until the clamping shank snaps on the foot.

ONE-PIECE TYPE
Raise the presser bar to its highest position by lifting the presser foot lever. Loosen the presser foot thumb screw and remove the foot.
Insert new foot from the front and tighten the screw using the large screwdriver to make certain the foot is secure.

https://manual-hub.com/

BUTTONHOLE ATTACHMENT
You will find the following parts in your Attachment Box:
1. Cover Plate with pinion gear in the center.
1 Buttonhole adapter to be used instead of base cover When buttonhole attachment is used. (Free-arm type only).

3. A set of 2 templates is furnished

with each attachment.

Each

template is marked showing the

type and length of each buttonhole.

= Desired size of buttonhole is selected by turning template advance knob. Length of buttonhole appears in window on top side of guide plate.
Details in using this attachment are given in the next section. Follow those directions carefully for perfectly formed buttonholes.

https://manual-hub.com/

Now that you are familiar with the controls on your machine and with the accessories provided for the machine, you are ready to start to sew with your new Kenmore sewing machine. Below are some good habits to follow each time you sit down to sew:
, Test the needle - it should be straight, properly set and sharp on the point, It should be the correct size for the fabric and thread being used. Do not be afraid to change your needle frequently. Many of the new fabrics made of synthetic blends tend to dull the needles more easily than fabrics made of natural fibers.
2. Before placing the material on the machine, see that the ends of the threads have been drawn about 4 inches to the rear of the machine.
3. Test the machine stitch on a scrap of fabric you plan to use. The fabric should be dodble thickness, Adjust the machine for the length of stitch and tension suitable to your fabric.
, Fabric should be placed under the presser foot with the bulk of the material to the left of the needle and the right edge of the material placed on the 5/8" seam marking on the needle plate when making a simple seam.
° Run the machine at a slow even speed. The more pressure you put on the speed control, the faster the machine will sew.
. Fasten each seam by back tacking at the beginning and end of the seam.
7. Always finish sewing each seam with the needle at its highest point.
o Guide the fabric gently with your hand in front of the needle. Never pull or hold the fabric in such a way that the normal feeding is altered.
9. When turning the hand wheel manually, always turn it toward you.

https://manual-hub.com/

GARMENT

CONSTRUCTION STITCHES

....

STRAIGHT STITCHING
Set your machine just as shown in the illustration in order to straight stitch. it is important each dial have the following settings.
SETTINGS
Special Stitch Dial . wwa_--_ Stitch Width Control - Red Dot Stitch Length Control - 12 to 6 Special Stitch Modifier - Red Dot Straight Stitch Foot Straight Stitch Needle Plate

You will find in garment construction that you are doing two types of sewing - temporary and permanent. 1. Temporary stitching - Usually the longest stitch possible and often done
on a single layer of fabric. The various types of temporary stitching are: Basting Stay stitching Guide line marking
2. Permanent stitching - This is the actual stitching that holds the garment together. Much of this stitching is visible on the outside of the garment and therefore must be good looking.
The best length stitch to use for medium weight fabrics is 10- 12 stitches per inch. This is in the middle range of the Stitch Length Control. You must remember to lengthen the stitch for heavier fabrics, multiple layers of fabric and thicker seams. Some of these seams are:
Common two layer seams Curved two layer seams Top stitched three layer seams Top stitched four layer seams When you have two seams crossing each other with considerable thickness, sew slowly and carefully so the seam will be as strong as possible in this area.
FASTENING A SEAM
Be sure both threads are drawn back under the presser foot. Lower needle into fabric about 1/2 inch from beginning of seam. Turn the reverse stitch control clockwise and stitch in reverse until needle reaches beginning of seam. Release control and complete seam. When you reach the end, turn the control clockwise and sew back over 1/2 inch of completed seam.
26
https://manual-hub.com/

TURNING A SQUARE CORNER
To turn a square corner 5/8" from the fabric edge, stop stitching with the needle tip piercing the fabric, when reaching the cornering guide as shown. Raise the presser foot, turn fabric. New stitching line will align with 5/8" seam guide on side of needle plate. Lower the presser foot and begin stitching in new direction.
ZIGZAG STITCHING
SETTINGS
Special Stitch Dial - ww_=_-Stitch Width Control - 1 to 4 Stitch Length Control - Any number Special Stitch Modifier - Red Dot Zigzag Presser Foot Zigzag Needle Plate
This type of stitching greatly expands the use of your machine. This is the feature that enables you to overcast seams, blind hem, applique, buttonhole, monogram, and make all the pretty embroidery designs by machine. Simply use the settings indicated in the illustr_ion for the simple zigzag. Follow directions given in the following pages for more specific uses.
OVERCASTING
This is one of the more frequently used zigzag stitches in garment construc. tion. You may, want to overcast along the raw _edge of each seam allowance or fold the raw edge toward the garment and stitch.
Fig. 1 shows the raw edge finished. Fig. 2 illustrates the folded edge stitch-
ed.
Stitch so the needle pierces the fabric just short of the outside edge. Raw or Worn edges of older garments can be overcast to prevent further raveling.
27
https://manual-hub.com/

STRETCH STITCHING
The stitches shown below are all for use with stretch and knit fabrics. These are special stitches built in to the machine for your quick selection.

1. Straight Stretch

I\I
\,/,,>

2. Rick _ Rack Stretch

·k

3. Smocking Stretch

4. Elastic Stretch

/\/ \/\

5. Overcast Stretch

/\/

\/\

6. Serging or Pine Leaf Stretch

/\/

% J%

(I)®®®®®

STRAIGHT STRETCH STITCHING
SETTINGS
Special Stitch Dial - v_l_i_ Stitch Width Control- Red Dot Stitch Length Control - 6 ..... Special Stitch Modifier - White Dot Straight Stitch Foot Straight Stitch Needle Plate
Use this stretch stitch with knitted fabric and other, fabrics that stretch. Sew as you do with regular straight stitch seaming. The seam may be pressed open as with any regular seam, but will stretch if necessary.
This is also a good stitch to use on curved seams regardless of the type of fabric. Any seam that will receive a great deal of strain when worn should be sewn with the stretch stitch. Use in children's shorts and slacks as well as adult sports clothes,

https://manual-hub.com/

RICK-RACK STRETCH

STITCHING

....

SETTINGS
Special Stitch Dial - wN_=-" Stitch Width Control - 1 to 4 ·Stitch Length Control - 6 Special Stitch Modifier - White Dot Zigzag Presser Foot Zigzag Needle Plate
Use this special stitch for al!-purpose heavy duty sewing of stretch fabrics: Sew as you do a 'regular plain zigzag seam. The machine will make triple lock stitchesback and forth of a fixed stitch length, to give the stretch to seam,

SMOCKING STRETCH STITCHING
SETTINGS
Step 1. Make s straight line of gathers across the fabric that you wish to smock.
Step2. Speciai St!tch Dial ; V,"¢_. Stitch Width Control - 3 to 4 Stitch Length Control - 6 Special Stitch Modifier - White Dot Zigzag Presser Foot Zigzag Needle Plate

With a narrow strip of fabric directly

under the line of gathering, stitch over

....

the gathers. The design will be a series

of small diamonds.

When smocking a garment, the stitching should be done before the piece is sewn into the garment.

https://manual-hub.com/

OVERCAST STRETCH .......... STITCHING
SETTINGS
Special Stitch Dial. "VV WW Stitch Width Control - 4 Stitch Length Control - 6 Special Stitch Modifier. White Dot Zigzag Presser Foot Zigzag Needle Plate
This is the same type of stitch used by the garment industry in making sportswear. It is used for seams of 3/8" to 1/4"', The seam is formed and finished in one operation. It must be used when you are making swimwear, ski pants and other garments that require stretch.
Fig. 1 shows the raw edge finished.
Stitch so the needle pierces the fabric just short of the outside edge.
Raw or worn edges of older garments can be overcast to prevent further raveling.
ELASTIC STRETCH STITCHING
SETTINGS
Special Stitch Dial - J_'_ Stitch Width Control - 4 Stitch Length Control - 6 Special Stitch Modifier - White Dot Zigzag Presser FoQt Zigzag Needle Plate

https://manual-hub.com/

This is a good stitch to use in making or repairing lingerie. The stitch is decorative as well as useful, Simply stitch the elastic into place around the waist of the garment, making sure that the elastic is evenly spaced. To do this mark the correct length piece into quarters and match these markings with center front and back of the garment as well as side seams.

After the basic construction of your garment is finished, there are still many finishing touches to be done. To aid your completion of your garment, the Kenmore has been designed to do the following tasks that formerly had to be done by hand.
BUTTONHOLE MAKING
(Model 1625 only)
SETTINGS
Special Stitch Dia!- w_]-.--Stitch Width Control - 1 to 1_ Stitch Length Control- 12 Buttonhole Control - F Special Stitch Modifier- Red Dot Bottonhole Foot Zigzag Presser Foot Zigzag Needle Plate

. Place the fabric, with the buttonhole

marked, under the buttonhole foot.

Without lowering the foot, let the needle pierce the fabric at the

beginning of the buttonhole. Pull the foot all the way forward so that the index mark (A) is aligned with the graduation (B). Lower the foot. (Reproduction of the identical size buttonholes is facilitated with the aid

of the graduations cn the left side of

the buttonhole foot. These gradua-

tions are 1/8" apart. Graduations act

as reference mark.)

. W_th the buttonhole control at F, stitch forward until you approach the front marking of your buttonhole.

··: · ······i··_··i···!·i_i:_···'·:_!·_i·:!:i_···!i·!·_::··i_ii:

https://manual-hub.com/

3. Turn the control to "R" stitching _ back to the beginning of the buttonhole. _The speed with which the control is turned determines the number of stitches at the end of the
buttonhole_ The slowerthe control is turned while sewing, the more stitches foimed. .......

4. Turn the control back to F to finish buttonhole.

Always make a practice buttonhole on a scrap of fabric you pian to use. Try the buttonhole with the button you will use.
Always use an interfacing in area of garment where buttonholes are placed. Tissue paper or regular interfacing can be used. Tear paper away after stitching, if it is used.
For heavier weight fabrics, loosen your top tension slightly and use a wider stitch width setting.

https://manual-hub.com/

BUTTONHOLE MAKING
Always make a practice buttonhole on a scrap of fabric you plan to use. Try the buttonhole with the button you will use.
Use an interfacing between the layers of fabric - tissue paper can be used and torn away after the stitching.
For heavier weight fabrics, loosen your top tension slightly and use a wider stitch w{dth setting.
SETTINGS
Special Stitch Dial - w_-_-=.Stitch Width Control - 1 to 1 Stitch Length Control- 0 Special Stitch Modifier- Red Dot Feed Dogs- Down Buttonhole Foot or Satin Stitch Foot Zigzag Needle Plate or Hole
1. Turn hand wheel so needle is down. Remove base front cover by pushing release button. Open shuttle cover. Insert buttonhoel adapter minus cover plate with pinion gear. Insert cover plate at 45 degree angle. Snap into place,
2. Screv_ guide pin into the guide pin hole on the base directly behind the needle plate. Pull guide plate forward as in Fig. 2.
3. Insert a template into the slot of template holder by lifting the bottom portion of the Template Holder. Select the proper size buttonhole by turning the Template Advance Knob.

https://manual-hub.com/

4. Pull guide plate all the way forward so that guide pin is at S. This will enable you to start at one end of the buttonhole. Drop guide plate into place over gear on cover plate.

., ,

o Pick up bobbin thread through guide plate by turning hand wheel and drawing thread to back of machine. Place fabric between

·Fig. 5

presser foot and guide plate. Line up edge of fabric with marked indentation on guide. See Fig, 4. If you wish all buttonholes to be 3/4 inch from edge of garment, line up fabric with 3/4 inch marking each time you start sewing a buttonhole.

https://manual-hub.com/

BLIND HEMMING
SETTINGS Special Stitch Dial - WWW Stitch Width Control - 2 to 3 Stitch Length Control - 12 to 8 Special Stitch Modifier - Red Dot Zigzag Presser Foot or Edgestitcher if available Zigzag Needle Plate
1. Finish edge of hem anyway you desire. Turn up hem appropriate width. (Fig, 1)
2. Fold garment away from hem leaving 1/8" of hem edge extending: (Fig. 2)

3. Place garment under presser foot in such a manner that straight stitches will be sewft on extended edge, The zigzag stitch should just catch the fold of the garment, (Fig, 3)
4. Press both sides of the finished hem. The right side of the garment will show only the blind stitches. (Fig. 4)

https://manual-hub.com/

°4 o

SATIN STITCHING
SETTINGS
Special Stitch Dial . w_l_= Stitch Width Control - 1 to 4 Stitch Length Control - Red Zone Special Stitch Modifier - Red Dot Satin Stitch Foot Zigzag Needle Plate

Closely spaced zigzag stitches are ca|led satin stitches. This is an attractive stitch used for appliqueing, monogramming, buttonhole making. Whenever you are using this stitch, it is well to remember to loosen the tension of the top thread slightly. The wider the stitch you make, the looser the tension should be.
If you are stitching on a very soft fabric, it is well to use a backing of tissue paper or interfacing for a well formed stitch. Puckering of the material will be eliminated and the bobbin thread will not be visible on the right side of the fabric.
As with all special stitches, it is best to make a sample design on your fabric before starting the design on the garment.
APPLIQUEING
SETTINGS
Same as with Satin Stitching
Select an applique design to be applied to your garment and baste it in place. Satin stitch around the raw edge of the applique completely covering the edge. You may want to do this with a contrasting cOlor of thread or self color.

https://manual-hub.com/

ZIPPER APPLICATION
SETTINGS Special Stitch Dial - w_l_..=Stitch Width Control - Red Dot Stitch Length Control - 12 to 10 Special Stitch Modifier - Red Dot Zipper Foot Straight Stitch Needle Plate
REGULAR ZIPPER
The foot is adjustable for use on the right or left side of the needle when sewing the regular type of zipper. Adjust the foot so the needle clears the side notch on the foot. See Fig. 1. Carefully follow directions given on the zipper package.
INVISIBLE ZIPPER
Adjust the foot so the needle is sewing through the center hole of the foot and one groove of the foot is riding on the teeth of the zipper. See Fig. 2. Follow the zipper manufacturer's instructions.
After zipper_ has been inserted, finish sewing seam by shifting foot to side position sewing through side notch.
CORDING
Foot can also be used to make cording for slipcovers etc. Cover a cord with a strip of bias fabric and sew as shown in Fig. 3.

https://manual-hub.com/

MENDING
SETTINGS
Special Stitch Dial -.V_._ Stitch Width Control - 4 Stitch Length Control - Red Zone Special Stitch Modifier - Red Dot Zigzag Presser Foot Zigzag Needle Plate
To repair a straight or three-cornered tear, position the tear under the needle in such a waythat the stitching catches both sides of the tear. When mending a three-cornered tear, stitch from each end to the center. It is well to use a piece of fabric under the tear for reinforcement.
DARNING
SETTINGS
Special Stitch Dial. ww_[]_.-_ Stitch Width Control - Red Dot Special Stitch Modifier Red Dot Feed Dogs -Down No Presser Foot
Remove presser foot, stretch fabric between embroidery hoops with hole centered. Draw the bobbin thread up through the fabric by holding the top thread and taking one stitch at the spot where you wish to start darning. Lowering the presser bar, start sewing at a slow to medium speed. Move the fabric back and forth with _a steady rhythm to cover the darning area. When it is covered, turn the fabric and sew another layer of stitching across the first layer of stitching.

BUTTON SEWING
SETTINGS
Special Stitch Dial - ww_=-._ Feed Dogs - Down Zigzag Presser Foot Zigzag Needle Plate
1. Align two holes of button with slot of presser foot and lower foot to hold the button securely.
2, Turn hand wheel manually until needle point is just above button,
3. Adjust stitch width control so needle will enter left hole of the button.
4, Turn hand wheel again by hand so needle enters second hole. Readjust stitch width if necessary, Stitch a number of times.
5. Finish sewing with an extra two inches of thread remaining; Draw these threads to reverse side of garment and tie.
BAR TACKING
SETTINGS
Special Stitch Dial - v,w_]:-=.Stitch Width Control - 2 to 4 Stitch Length Control - Red Zone Special Stitch Modifier - Red Dot Zigzag Presser Foot Zigzag Needle Plate
This stitch is similar to a very short satin stitch and is used to reinforce points of strain such as corners of pockets and straps on lingerie.
Sew 4 to 6 zigzag stitches.

https://manual-hub.com/

FREE-ARM SEWING (Free-arm type only)

This sewing machine can be used like a flat bed machine, but easily converts to free arm machine by removing the base.
The free arm enables you to sew tubular types of pieces more easily. Just slip the sleeve or pants leg on the free arm as shown above.
You will find many uses for this free arm feature such as:
1. Mend elbows and knees of garments more' easily.
2. Sew in sleeves more easily. This is especially true when sewing smaller garments.
3. Applique, embroider or hem around edges of cuffs or pants legs.
4. Sewing in elastic casings in skirts or pants at the waistline.

https://manual-hub.com/

3. CHECKING PERFORMANCE PROBLEMS WHAT TO DO

J:_

https://manual-hub.com/

· _i _

ii _z _ _ !ii , _

_i _

i¸ _

https://manual-hub.com/

CARING FOR THE MACH NE ................................................................................................ CLEANING AND OILING

Fig. 1 Cleaning the feed dogs with a brush.

To insure the best possible operation of your machine, it is necessary to keep the essential parts clean at all times. Using a small brush, remove the lint that accumulates in the shuttle area and around the feed dogs.
Fig. 2 Parts of the Shuttle Assembly

Fig. 1

To Clean the Shuttle Area:
1. This area must be kept free of dust, lint and occasional tangled thread. Raise the needle bar to its highest point and remove the bobbin case.
, Push levers of shuttle race aside and lift shuttle race cover and shuttle out.
. Clean the shuttle race with small brush,
. Put a drop of oil on the center pin of the shuttle and shuttle race. (see arrows)

To Replace Shuttle Assembly-
1. Position shuttlerace as illUStrated so that shuttle driver is forming half moon on the left side of the machine.
. Hold shuttle by center pin and position shuttle so as to form a half moon on the right side, Pointed hook will be on the bottom.
= Place shuttle race cover into place over shuttle assembly.

https://manual-hub.com/

OILING UNDER ARM COVER PLATE
Remove arm cover plate to oil points indicated in top of machine head. To remove cover plate, insert a screw driver into the spacing between arm casting and top cover plate and lift the cover plate as illustrated below.

https://manual-hub.com/

OILING UNDERSIDE (Free_armtype)
Tilt maqhine head back and remove bottom cover to oil points indicated on underside of machine. To remove bottom cover, remove screws (A), (B), (C), (D) and (E) as shown below.

https://manual-hub.com/

/it =

OILING UNDERSIDE (Flat-bed type)
Tilt machine head back to oil points indicated on underside of machine.
<
OILING IN FACE cOVER PLATE
Swing hinged face cover plate open and oil points indicated in illustration.

https://manual-hub.com/

PART LIST

https://manual-hub.com/

PARTS LIST

All parts listed herein may be ordered from any Sears, Roebuck and Co. or Simpsons- Sears Limited store or service center.

WHEN ORDERING REPAIR INFORMATION :
1. PART NUMBER 3. MODEL NUMBER

PARTS,

ALWAYS GIVE THE
2. PART DESCRIPTION 4. NAME OF ITEM

FOLLOWING

If the parts you need are not stocked locally, your order will be electronically transmitted to a Sears Repair Parts Distribution Center for expedited handling.

Ref. No.
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
25 26 27 28 29 30 31 32 33

Part No.
47 38295 38296 36210
6510 *6862
1939 8286 2273 *6550 "6551 *6552
*6553 *6554 *6746
40390 6870 6873 6757
40396 37174 37175
42063 42064
42062 41040 43840
6757
41662
35346 35347 48274
40530 36214
6864
6797 6830 41670 41669 *6890

Description
Shuttle
Needle plate insert...Zigzag stitch Needle plate insert...Straight stitch Multi purpose needle plate Bobbin case
Bobbin box with 10 bobbins
Bobbin winder rubber ring Thread spool pin Nylon disc No. 9 needles No. 11 needles No. 14 needles
No. 16 needles No. 18 "needles Q NEEDLES
Standard zigzag foot Satin stitch foot
Straight stitch foot Zipper foot Standard zigzag foot Satin stitch foot
Straight stitch foot
Standard zigzag foot , Satin stitch foot
Straight stitch foot Buttonhole foot
Buttonhole guide foot
Zipper foot Buttonhole guide plate Buttonhole template (No. 1) Buttonhole template (No. 2) Buttonhole adapter
Buttonhole cover plate Buttonhole cover plate Needle threader
Light bulb Buttonhole opener Large screw driver Small screw driver Oil/oiler

https://manual-hub.com/

SEWING MACHINE
Now that you have purchased your Sewing Machine, should a need ever' exist for repair parts or service, simply contact any Sears Service Center and most Seam, Roebuck and Co. or Simpsons-Seam Limited Stores. Be sure to provide all pertinent factswhen you call or visit.
The model number of your Sewing Machine will be shown on your nomenclature plate on the right side of your Sewing Machine. See page 3 for location.
:;_ WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE iili; FOLLOWING INFORMATION:
*MODEL NUMBER *NAME OF ITEM *PART DESCRIPTION
If the parts you need are not stocked locally, your order will be electronically transmitted to a Sears Repair Parts Distribution Center for handling.
l':ii.

iiiiii_iii
_?iii SEARS, ROEBUCK AND CO., Chicago, IL60684 U.S.A. and

i SlMPSONS-SEARS

LIMITED, Toronto, Ontario, Canada

$ - 158

Part No. 59982(_)

https://manual-hub.com/

References