Dante | Getting Started - KLANG blogKLANG:quelle | Dante Breakout and Headphone Amp – Quick Start GuideRegister - KLANG blog
User Guide for KLANG models including: Dante 4 channel headphone amp
1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP CONNECTIONS ROUTING TECHNICAL DATA 1 Connect external power supply if your network does not o˜er Power over Ethernet (PoE).
KLANG:quelle | Dante Breakout and Headphone Amp – Quick Start Guide
File Info : application/pdf, 2 Pages, 206.51KB
DocumentDocument4 channel headphone amp MORE INFORMATION ONLINE: /quelle STEP 1 CONNECTIONS 1 Connect external power supply if your network does not offer Power over Ethernet (PoE). 2 Connect CAT5e/CAT6 network cable to KLANG:quelle and to your computer or Dante enabled product/network. Mixing Console Output Card without PoE STEP 2 SOURCE If you have another Dante enabled product (e.g. mixing console) proceed with STEP 3. If not, follow the instructions below to enable your computer to stream audio via Dante. 1 OPEN www.KLANG.com/dante 2 Install Dante Virtual Soundcard (DVS) (free trial license available). 3 Start Dante Virtual Soundcard. 4 Set DVS as your output sound card. Play! audio signals STEP 3 CONTROLLER 1 OPEN www.KLANG.com/dante 2 Install & Start Dante Controller (DC). 4 Turn off WiFi on your computer. 3 In DC, go to ROUTING tab and double click on your sound source. Go to DEVICE CONFIG tab and choose preferred sampling rate. Close this window. 4 Now, do the same for KLANG:quelle and use the same sampling rate. Note: Dante devices can only be connected if they run at the same sampling rates! (Default: 48kHz) SOURCE Ch 01 Ch 02 Ch 03 pdi-24-05-19 STEP 4 ROUTING Connect (stereo) audio stream from sound source to KLANG:quelle Out Left and Right. Dante Controller STEP 5 ENJOY LISTENING Connect your headphones and adjust the GAIN Select switch: In-Ears: -12 or 0dB | Other: 0 or +12dB. Volume GAIN control Select switch KLANG:quelle Out1 Left Out1 Right Out2 Left Out2 Right Analog Outputs linked to GAIN Select switch. IEM Transmitter IEM Beltpack STEP 6 TECHNICAL DATA WARNINGS AND PRECAUTIONS Do not remove covers. Connect only to main sockets outlets with protective earth. Do not handle power cords with wet hands. Do not expose to water or other types of liquids or moisture (rain, fog, dew etc.). Operating temperature: 0 °C to 50 °C (32 °F to 122 °F). Do not expose to heat sources. COMPLIANCE KLANG:quelle has been tested and found to comply with the requirements defined in: EN55103-1:2009 EN 55103-2: 2009. EN 55022:2006 / CISPR 22:1997 CAN/CSA-CEI/IEC CISPR 22:02 FCC 47 CFR, Part 15. SAFETY EN 60065, 7th Edition, Rev.: 09/21/2012; CAN/CSAC22.2 No. 60065:03 (R2012). RoHS Compliant and Pb-Free. WEEE RECYCLING According to RL2002/96/EG (WEEE Directive on Waste Electrical and Electronic Equipment) electronic equipment has to be recycled and does not belong in the standard waste. If you are unsure how to recycle this product please contact us and we will recycle the device for you. DIMENSIONS Weight: 2.9 kg | 6.4 lbs, Size (W/H/D): 44.5 / 4.5 / 18.5 cm Front panel (width): 48.5cm | 19 inches 1 rack unit, gap between rack bolts (W/H): 46.5 / 3.5 cm. WARRANTY REGISTER ONLINE: www.KLANG.com/register © KLANG:technologies GmbH, Aachen, Germany, 2019. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means--electronic, mechanical, photocopy, recording, or otherwise--without written permission by KLANG:technologies GmbH | Wespienstr. 8-10 | 52064 Aachen | Germany. +49 241 89 03 01 22 support@KLANG.com www.KLANG.com/quelle