Philips PV Vertical Panel 200Wp Installation

Safety Precautions

• ℹ️ The system must be installed by qualified personnel only.
• ⚠️ Disconnect luminaire battery and photovoltaic panel before installing.
• ⚠️ Use gloves while any operation.
• ℹ️ Follow this document for system installation.
• ⚠️ Do not modify the fixation procedure.
• ⚠️ Risk of accident if any incorrect torque tightening.

Product Identification and Ordering

The photovoltaic vertical panel and the kit for the installation can be ordered by these two codes:

• 911401822202: 200Wp Vertical Panel Subsystem Vmpp 36V
• 912300058711: Kit for the installation of the PV Vertical Panel in SunStay PRO Upgrade

Included Components:

• PV panel module (1x)
• Fixing holders (2x Male & 2x Female)
• MC4 adapter (1 Male & 1 Female)
• Mounting Instructions
• Cables extensions (1x Male & 1x Female)
• 1 x Grey cable gland
• 1 x Sleeve 1200mm (47in)
• 1 x Sleeve 650mm (25in)

Contact your local Signify employee for further information.

Dimensions and Specifications

Panel Dimensions:

• Length: 2000 mm (78.75 in)
• Pole range: Ø75-160 mm (Ø3-6 in)
• Width: 200 mm (7.87 in)
• Height: 228 mm (8.98 in)

Component Specifications:

Electrical Specifications:

• All MC4 male connectors are positive 18/36V+.
• All MC4 female connectors are negative 18/36V-.
• MC4 adapters (30cm) must be used only in case of installation of more than two Vertical PV Panels.
• The MC4 connectors at the end of the red cables are to connect master-module and sub-module.
• Do not connect the MC4 male and female connectors from the last master module.

Installation Height Recommendation:

The minimum recommended height to prevent from vandalism is 8.2 feet (2500 mm). This height can be reconsidered by the installer according the specific conditions.

Installation Steps

Step 1: Fixation to the Pole

Attach the fixing holders to the pole. Ensure they are positioned correctly for panel mounting.

Step 2: Secure Panel

Place the panel and secure it using the fixing holders. Tighten bolts to the specified torque (M8 16Nm) using a calibrated torque wrench.

Step 3: Connect Cables

Connect the cables to the PV panel module. Ensure correct polarity.

Step 4: Mount Panel Assembly

Attach the panel assembly securely to the pole.

Step 5: Cable Management

Route and secure the cables along the pole.

Step 6: Electrical Connections

Connect the extension cables. Ensure connections are secure.

Step 7: Final Cable Securing

Secure all connected cables, paying attention to the connector details shown in the close-up view.

Step 8: Completed Connection

The electrical connections are now complete for this stage.

Step 9: Panel Orientation

Adjust the panel's orientation as required.

Step 10: Final Torque Tightening

Perform final tightening of the panel mounting bolts to the specified torque (M8 16Nm).

Step 11: Luminaire Connection

Connect the panel cables to the luminaire. Attention: Do not connect the MC4 male and female connectors from the last master module.

Step 12: Multi-Panel Installation

In case of more than one Photovoltaic Vertical Panel, use the MC4 adapters for series connection.

Step 13: Luminaire Wiring

Connect the PV Vertical Panel to the luminaire. This may involve drilling a hole (Ø20mm) in the pole at a distance of 150mm-500mm (5.9in-19.7in) from the top.

Step 14: Internal Luminaire Connections

Make the internal electrical connections within the luminaire. Ensure correct torque for M20 connections (2.2Nm).

Step 15: Detailed Luminaire Wiring

Follow the detailed wiring diagram for connecting the panel to the luminaire's internal components. Ensure correct torque for M20 connections (1.8Nm).

Step 16: Final Luminaire Assembly

Complete the internal wiring and secure the luminaire components.

Step 17: Internal PV Connections

Observe the internal connections for PV1 and PV2, noting positive (+) and negative (-) terminals.

Step 18: Final Connection to Luminaire

Make the final connection to the luminaire. Attention: Do not connect the cables incorrectly.

General Warnings

Important: All storage, installation, use, operation, and maintenance of the products must be performed exactly according to the instructions in this manual and/or other instructions provided by Signify to guarantee safe use over its entire lifetime. Failure to adhere to these instructions will invalidate your entitlement to warranty. Bolts with torque indication on the drawing need to be tightened using a calibrated torque wrench. Pre-assembled bolts need to be retightened again to the required torque specification to assure maximum strength over lifetime.