SAMEBIKE 20LVXD30 Electric Folding Bike

1. Important Warnings ⚠️

• This manual contains crucial safety and service information. Read all warnings before first use.
• When lending the e-bike to others, ensure they read this manual to reduce accident risk.
• Always wear a suitable and safe helmet. Use clothing with fluorescent and reflective strips when riding at night.
• Do not exceed speed limits; this is a primary cause of traffic accidents. Adhere to traffic regulations.
• Avoid touching the charging port with metal objects, as this can cause a short circuit.
• To maximize endurance, avoid frequent starting/stopping, riding against wind, overloading, and ensure proper tire pressure. Utilize the assist mode.
• Avoid prolonged exposure to sun or rain, and storage in high-temperature or corrosive gas environments to prevent damage to components and paint.
• Verify your insurance coverage for e-bike usage.
• In China, the minimum age for riding an e-bike or electric tricycle is 16 years. Comply with local laws and regulations in other countries.
• E-bikes are vehicles with inherent risks. When performing an emergency brake, apply the rear brake first, then the front brake, to prevent tipping over. Ride cautiously.

2. Product Components

Identify the parts of your SAMEBIKE 20LVXD30:

• ? 1. Saddle
• 2. Seatpost
• 3. Rear Rack
• 4. Front/Rear Fender
• 5. Motor
• 6. Battery
• 7. Folding Mechanism
• 8. Crankset
• 9. Pedal
• 10. Chain
• 11. Display
• 12. Vertical Handle Stem
• 13. Brake Lever
• 14. Suspension Fork
• 15. Front/Rear Disc Brake
• 16. Tire
• 17. Kickstand
• 18. Front Light

3. Product Folding Method

Follow these steps to fold your e-bike:

1. Adjust the seatpost and loosen the seatpost clamp using the quick release. Slide the seatpost down. If applicable, adjust the crank angle to 9 o'clock and fold the pedals simultaneously.
2. Open the frame by unfolding it, using the safety latch. Fold the left and right sides of the frame.
3. Open the frame's folding mechanism. Ensure the front wheel is nearly parallel to the rear wheel as you complete folding the bicycle.

4. Product Assembly Method

4.1 Tool Preparation

Ensure you have the following items before assembly:

• Tools (provided in the kit)
• User Manual
• Charger

Note: Packing list items (gift styles and colors) may vary and are not grounds for return.

4.2 Attaching Fenders and Headlight

1. Secure the screws for the front fork using the provided tool.
2. Mount the headlight and front fender using the screws and tighten them.
3. Secure the screws on both sides of the front fork.
4. Secure the screws on both sides of the front fork.

4.3 Front Wheel Installation

1. Attach the headlight and front fender to the screws and tighten them.
2. Prepare the front wheel.
3. Insert the wheel into the front fork slot.
4. Mount the disc brake components onto the steering with the disc brake.
5. Align the quick-release lever and nut on the wheel.
6. Tighten the nut on the screw.
7. After tightening with appropriate force, align the quick-release lever in the indicated direction.
8. Secure the quick-release lever to complete the front wheel installation.

4.4 Handlebar and Stem Adjustment

1. Open the stem folder.
2. Fold the handlebar to the left.
3. When installing the stem, ensure the handlebar is correctly aligned and tightened.
4. Fold the handlebar vertically to the ground.
5. Loosen the quick-release lever of the stem and adjust the handlebar to the desired position, then tighten the quick-release lever to secure the handlebar.

4.5 Pedal Assembly

This bicycle includes practical accessories.

1. Take the wrench from the toolkit.
2. The 'R' pedal must be installed on the right side, and the 'L' pedal on the left side.
3. Tighten the nut counter-clockwise.

5. Saddle and Seatpost Adjustment

1. Adjust the saddle angle.
2. Open the seatpost clamp.
3. Adjust the saddle and rotate.
4. Secure the seatpost clamp.

6. Battery Removal Method

Note: The battery cannot be removed on the Standard Version.

1. Open the frame latch.
2. Loosen the frame latch to access the battery compartment.
3. Insert the key into the battery lock.
4. Remove the battery.

7. Product Instruction - Charging Method

7.1 Charging Method (Integrated Battery)

Bild 1 (For Standard Version and High-End Version)

1. Take out the charger.
2. The charger is located on the left side of the frame, near the folding mechanism.
3. Plug the charger into the socket.
4. A red light indicates charging; a green light indicates a full charge.

7.2 Charging Method (Removable Battery)

Bild 2 (Suitable for High-End Version with Removable Batteries)

1. Take out the charger.
2. You can take the battery out to charge it at home or elsewhere.
3. Plug one end of the charger into the battery and the other end (blue) into the power supply.
4. A red light indicates charging; a green light indicates a full charge.

8. Notes and Pre-Ride Checks

1. Read the user manual carefully before riding. Ensure all parts are in good condition for safety.
2. Check the vehicle's status: brakes, wheels, handlebars, folding clasp, and quick releases to ensure the e-bike is in good working order.
3. Check the electrical system: Ensure the battery has sufficient charge. Recharge if necessary.
4. Verify the brake system is functioning correctly. If not, contact customer service.
5. Insert the stem to a depth that meets or exceeds the minimum insertion depth indicated by the safety line.
6. The seatpost height can be adjusted to personal preference, but must not be inserted below the minimum safety line. Secure it properly.
7. Pedal Installation: If you purchased a new product, you must install the pedals yourself. Pedals are marked 'R' for right and 'L' for left. Tighten them counter-clockwise.

9. Warranty Terms

1. Users should operate the product according to the manual. In case of performance failure due to production quality, the company will fulfill its three-guarantee obligations as per relevant laws and regulations.
2. The company is responsible for after-sales service for issues beyond the three guarantees, including main components, though repair costs may apply.
3. If the battery needs replacement during the warranty period, the company will supply it at factory price. For safety and environmental protection, the battery must be recycled 1:1 and returned to the battery manufacturer.

Certifications:

• EPAC EN 15194
• FCC
• CE

10. Additional Information

Tagline: PROVIDE LIGHT PRACTICAL MODERN AND SIMPLE IDEAL TRAVEL MODE

For more solutions and information, visit our YouTube channel: SAMEBIKE YouTube Channel