SuperATV Installation Instructions

Overview

This document provides installation instructions for the SuperATV Roof designed for the Yamaha Wolverine X4.

Important Notes:

• SuperATV recommends securing the Roof with straps when transporting on an open-air trailer.
• This item is not returnable if the protective film has been removed.
• Test fit the Roof to the cage to confirm fitment before removing the film.
• Do not discard packaging until the product has been successfully installed.

Kit Contents

Disregard any remaining hardware and/or components not used in this installation.

Roof Cleaning Instructions

• Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
• Do not use window cleaning fluids (Windex, 409, etc.) or any solvents (gasoline, denatured alcohol, acetone, etc.).
• Never use abrasive cleaners, abrasive pads, or gritty cloths.
• Thoroughly rinse Roof to float off dirt and mud.
• Using a soft cloth, or microfiber cloth, clean Roof with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand washing soap can also be used.
• To prevent water spots, use a chamois to blot Roof dry.

Step 1: Prepare Clamps

Separate hardware from all clamps. Set clamps and hardware aside. Keep large and small clamp bolts with their respective clamps.

Visual Description: Diagram showing disassembled clamps with bolts, nuts, and washers.

Step 2: Install Flat (narrow) on Crossbar

Install the Flat (narrow) piece to ONE SIDE ONLY of Crossbar (E), ensuring it runs the entire length of the bar. This does not apply to the remaining Crossbar (E).

Visual Description: Diagram showing the Flat (narrow) piece being attached to one side of a Crossbar (E) with fasteners.

Step 3: Install Flat on Front Support Bar

Install the Flat piece to the Front Support Bar (B), ensuring it runs the entire length of the bar.

Visual Description: Diagram showing a Flat piece being attached to the Front Support Bar (B) with fasteners.

Step 4: Assemble Front Components

Install the Front Support Bar (B) to the Front (A) using the provided hardware (4x M6 x 25mm bolts, 4x M6 Washers, 4x M6 Nuts, 4x Sealing Washers (small)).

Install the Right and Left Support Bars (H)(J) to the Front (A) using the provided hardware.

Secure the Right and Left Support Bars (H)(J) to the Front Support Bar (B) using the provided hardware (3x M6 x 20mm bolts, 3x M6 Washers, 3x M6 Nuts).

Visual Description: Diagram showing the assembly of parts A, B, H, and J with specific hardware noted (M6 x 25mm, M6 x 20mm, M6 Washers, M6 Nuts, Sealing Washers (small)). Labels indicate 'front', 'passenger', and 'driver' sides.

Step 5: Install Cage Foam

Clean the vehicle's cage and install the Cage Foam (inner) along the sides and across the centers. The Cage Foam (outer) should be placed against the optional SuperATV Rear Windshield or approximately halfway down the section of the cage.

Visual Description: Images showing the placement of inner and outer cage foam pieces onto the vehicle's roll cage.

Step 6: Join Front and Rear to Crossbars

Join the Front (A) and Rear (C) sections to the Crossbars (E) using the provided hardware (18x M6 x 25mm bolts, 18x M6 Washers, 18x M6 Nuts, 18x Sealing Washers (small)). Tighten all hardware.

Important: The Crossbar (E) with the gasket must be on the outside of the Roof. The gasket must face the plastic.

Visual Description: Diagram showing the Front (A) and Rear (C) panels being attached to the Crossbars (E) with fasteners. A warning symbol indicates the correct orientation of the gasket on the crossbar.

Step 7: Install Extension

Install the Extension (D) to the Rear (C) using the provided hardware (6x M6 x 25mm bolts, 6x M6 Washers, 6x M6 Nuts, 6x Sealing Washers (small)).

Visual Description: Diagram showing the Extension (D) being attached to the Rear (C) panel with fasteners.

Step 8: Secure Front to Cage

Secure the Front (A) to the vehicle's cage using the Small Clamps (x2). Refer to page 3 for clamp installation details.

Visual Description: Image showing two small clamps attaching the front section of the roof assembly to the vehicle's roll cage.

Step 9: Secure Front and Rear to Cage

Secure the Front (A) and Rear (C) sections to the vehicle's cage using the Large Clamps (x4). Refer to page 3 for clamp installation details. Repeat this process for the opposite side of the vehicle.

Visual Description: Images showing four large clamps attaching the front and rear sections of the roof assembly to the vehicle's roll cage.

Step 10: Secure Rear to Cage (Repeat)

Secure the Rear (C) section to the vehicle's cage using the Small Clamps (x2). Refer to page 3 for clamp installation details.

Visual Description: Image showing two small clamps attaching the rear section of the roof assembly to the vehicle's roll cage.

Step 11: Final Tightening

Align the complete Roof assembly to the machine and tighten all hardware securely.

Visual Description: Image showing the fully installed roof on the vehicle, with a note to tighten all fasteners.

Optional: Glass Windshield Installation

If a SuperATV Glass Windshield is installed, secure it to the Front (A) in the locations shown. Refer to page 4 for hardware details.

Visual Description: Diagram illustrating how a glass windshield attaches to the front section of the roof assembly.

Optional: Flip Windshield Installation

Install the Left FWS Bracket (J) to the clamp using the provided hardware (M6 x 20mm bolt) and tighten. Repeat this process for the Right FWS Bracket (H).

Visual Description: Image showing an FWS bracket being attached to a clamp with a bolt.

Optional: Full Windshield Installation

Install the Channel to the top of the windshield.

Visual Description: Diagram showing a channel piece being attached to the top edge of a windshield.

Need Help With Your Installation?

Contact SuperATV for assistance:

• Email: sales@superatv.com
• Phone: 1-855-743-3427
• Website: www.superatv.com

Support Hours:

• Monday - Thursday: 8:00 AM - 8:00 PM EST
• Friday: 8:00 AM - 7:00 PM EST
• Saturday: 9:00 AM - 2:00 PM EST

Read instructions and view illustrations before beginning.

Thank You For Choosing SUPERATV.

Liability Statement

SuperATV's® products are designed to best fit user's ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended. SuperATV's® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together.

Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product's ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times.

By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim.

SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers' products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified.

Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.

The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.