iPhone 14 Pro - Repair Guide

Apple iPhone User Guide PDF, Free Instruction Manual

Google Docs
Google Drive
Download [pdf]
File Info : application/pdf, 92 Pages, 27.56MB
Document Document

iphone-14-pro-repair-en

iPhone 14 Pro
Repair Manual
© 2023 Apple Inc. All rights reserved.

iPhone 14 Pro
Contents

Introduction

Basics

Internal View

Orderable Parts

Screws

10 Tools

Safety

15 Battery Safety 18 Broken Glass
Procedures

20 First Steps

SIM Tray

22 Display

54 Camera

63 Bottom Speaker

67 Taptic Engine

72 Battery 86 Top Speaker 89 TrueDepth Camera

Contents 073-00371-A | 2

iPhone 14 Pro
Introduction

Introduction

This manual includes technical instructions for replacing genuine Apple parts in iPhone and is intended for individual technicians with the knowledge, experience, and tools required to repair electronic devices.
Important
· Read the entire manual first. If you're not comfortable performing the repairs as instructed in this manual, don't proceed.
· Always use the latest version of this document available at support.apple.com/en_US/manuals/ iphone.

Warning
Failure to follow the repair instructions or to use genuine Apple parts or proper tools may cause fire or other safety issues and lead to personal injury or death.
Caution
Failure to follow the repair instructions or to use genuine Apple parts or proper tools may damage the iPhone, parts, or other property, or compromise the device's functionality or water resistance.
Warranty information
Damage caused by repairs performed outside of Apple or the Apple Authorized Service Provider network is not covered by Apple's warranty or AppleCare plans. Such damage may cause future repairs to be subject to out-of-warranty costs or render the device ineligible for future repairs by Apple or Apple Authorized Service Providers.

073-00371-A | 3

iPhone 14 Pro

Introduction

Tools and parts
Hardware tools
Apple tools are designed to apply the appropriate heat, force, and torque during repairs, and to withstand high-volume professional use.
· The heated display removal fixture softens adhesive to allow separation of the display from the enclosure. The fixture is used with a heated display pocket designed for the device's specific dimensions.
· The display press applies the appropriate amount of pressure to secure new adhesive during display installation. The display press is used with a repair tray and display adhesive press plate designed for the device's specific dimensions.
· The battery press applies the appropriate amount of pressure to secure new adhesive during battery installation. The battery press is used with a repair tray designed for the device's specific dimensions.
Ordering tools and parts
You can learn how to order genuine Apple parts and tools at support.apple.com/self-service-repair. During the purchase process, enter the manual ID CBLXRW to indicate that you've read this manual in its entirety and agree that you have the knowledge and experience to perform your intended repair.

Software tools
A System Configuration step may be required at the end of your repair. System Configuration is a postrepair software tool that completes the repair for genuine Apple parts. Running System Configuration has a number of purposes that vary based on the part replaced.

What System Configuration does
Transfers factory calibration values
Links Secure Enclave and biometric authentication parts
Ensures repair integrity
Assigns wireless region
Updates firmware

Why it's important Certain parts like displays, cameras, and ambient light sensors have calibration values that are customized to each individual part during manufacturing. Transferring these values ensures maximum performance and quality after a repair. After repair of a logic board or a biometric authentication part (Touch ID or Face ID), linking the biometric sensors to the Secure Enclave on the logic board is required to ensure device security.
After a hardware repair, software checks are performed to ensure repair integrity. Repair integrity means that a genuine Apple part has been correctly installed. To comply with regional communications regulations, a wireless region must be assigned to your logic board. Keeping firmware up to date ensures that the device has all the latest security and performance features.

073-00371-A | 4

iPhone 14 Pro

Introduction

System Configuration requirements The minimum requirements for System Configuration include: · The latest version of iOS--not a beta version--on the iPhone · A strong Wi-Fi network capable of 1.0 Mbps download and upload speeds, with less than 400 ms
latency and less than 2% packet loss. Estimated data usage to run System Configuration is 622 MB.
If the TrueDepth camera is replaced, System Configuration also requires:
· The latest version of Apple Service Utility installed on a Mac running macOS Monterey 12.4 or later · Internet access for the Mac · A Lightning cable
How to initiate System Configuration Depending on the part replaced, you will initiate System Configuration through one of the following two methods: · Put the device into diagnostics mode. Tap Start Diagnostics and follow onscreen prompts. or · Contact the online store where you purchased genuine Apple parts. See support.apple.com/self-
service-repair.
See the individual repair sections of this manual for more information.

Alerts

Failure to follow alerts could result in fire, injury, data loss, or damage to the device, parts, or other property.

Warning

Instructions for reducing risk of personal injury

Caution Important

Instructions for reducing risk of data loss or device hardware damage
Supplemental information for successfully completing procedures; neither a Warning nor a Caution

073-00371-A | 5

iPhone 14 Pro
Internal View

Internal View

1. Top speaker 2. Top speaker grille 3. TrueDepth camera assembly 4. Camera 5. Camera flex cables 6. Top battery adhesive tab 7. Battery 8. Bottom battery adhesive tabs 9. Bottom speaker 10. Lightning connector
© 2023 Apple Inc. All rights reserved.

11. Bottom microphones 12. Taptic Engine 13. SIM reader (only in iPhone models purchased
outside of the United States) 14. Battery flex cable 15. Display/Multi-Touch connector 16. Dock flex cable 17. Logic board 18. Ambient light/proximity sensor connector 19. TrueDepth camera flex cables 20. Grounding strap
073-00371-A | 6

iPhone 14 Pro
Orderable Parts

Orderable Parts

Name Battery Battery shim Bottom speaker Camera Camera cowling Display Display adhesive Logic board cowling Rubber gasket Security screws
SIM tray
Top speaker grille

Numbers 661-30382 923-08537 923-08123
661-29369 923-08125
661-29370 923-08094 923-08126
923-08127 --
923-08340 dual, space black 923-08341 dual, silver 923-08342 dual, gold 923-08343 dual, deep purple 923-08354 single, space black 923-08355 single, silver 923-08356 single, gold 923-08357 single, deep purple 923-08129

Screws -- -- 923-08147 (3) lower left, upper left, upper right 923-08377 (1) lower right -- 923-08160 (4) lower left 923-08375 (1) top 923-08376 (1) lower right -- -- 923-08155 (5) middle, lower right 923-08156 (1) left 923-08157 (2) upper right, middle left -- 923-08428 (2) space black 923-08429 (2) silver 923-08430 (2) gold 923-08431 (2) deep purple --
--

073-00371-A | 7

iPhone 14 Pro
Name Taptic Engine

Numbers 923-08124

Top speaker

923-08128

Top speaker grille

923-08129

Top speaker grounding strap 923-08365

TrueDepth camera

661-29367

Orderable Parts
Screws 923-08149 (1) left 923-08151 (1) upper right (super screw) 923-08374 (1) bottom 923-08159 (2) upper middle, lower right -- -- --

073-00371-A | 8

iPhone 14 Pro
Screws

Screws

Warning
· Never reinstall a screw after it has been removed. Install only new screws. iPhone screw grooves are covered in adhesive that can't be reused.
· Use only the torque driver indicated to install new screws during reassembly. Both overtightened screws and loose screws can damage parts.

Note: You can use any torque driver to remove screws. 923-08159

923-08375

923-08156

923-08155

923-08160 923-08376

923-08157

923-08155 923-08151 923-08149 923-08374

Torque driver (black, 0.35 kgf cm) Torque driver (green, 0.45 kgf cm) Torque driver (gray, 0.55 kgf cm) Torque driver (blue, 0.65 kgf cm) Torque driver (teal, 0.75 kgf cm)

Crosshead screw Super screw* Trilobe screw Security screw

*A super screw has a threaded hole that holds another screw.

923-08147
923-08377 923-08428 923-08429 923-08430 923-08431 Single screw Screw with super screw underneath
073-00371-A | 9

iPhone 14 Pro

Tools

Tools with part numbers are available for purchase from the Self Service Repair Store. Tools without part numbers can be purchased from electronics supply retailers.

923-07560 6.1-inch back protective cover

923-07561 6.1-inch display protective cover

661-29193 6.1-inch heated display pocket

923-08087 6.1-inch repair tray

923-01092 Adhesive cutter

923-02657 Battery press

Cut-resistant gloves

923-08081 Display adhesive press plate

661-08916 Display press

073-00371-A | 10

iPhone 14 Pro ESD mat

Tools

ESD-safe cleaning solution

ESD-safe tweezers

ESD wrist strap with clip or plug

Ethanol wipes1

661-28152 Heated display removal fixture2

Heat-resistant gloves

IPA wipes

923-01290 Micro stix® bit

Nitrile or lint-free gloves

922-5065 Nylon probe (black stick)

Safety glasses with side shields

073-00371-A | 11

iPhone 14 Pro Sand3

Sand container4

Tools
923-02066 Super screw bit

923-0248 Torque driver (black, 0.35 kgf cm) kit5

923-0448 Torque driver (blue, 0.65 kgf cm)

923-00738 Torque driver (gray, 0.55 kgf cm)

923-00105 Torque driver (green, 0.45 kgf cm)

923-08085 Torque driver (teal, 0.75 kgf cm)

1 Ethanol wipes must contain at least 90% ethanol and no additives except isopropyl alcohol.
2 Refer to Heated Display Removal Fixture Operating Manual for general use and precautions. 3 Clean, dry, untreated sand (810 cups) 4 Sand container (wide-mouthed, quick pour, nonbreakable plastic container with a flip-top lid) 5 The black torque driver kit includes a black torque driver (0.35 kgf cm), Torx® security bit (923-0247),
and JCIS bit (923-0246). The bits are also available separately.

073-00371-A | 12

iPhone 14 Pro
Heated Display Removal Fixture

Tools | Heated Display Removal Fixture

Note: A rented heated display removal fixture may have different packaging than shown. If your fixture came with a USB cable, set the cable aside. This setup doesn't require it.
1. Remove the fixture from the box. Then remove the packing foam.
Caution
Don't lift the fixture by the knob.

2. Cut and remove the zip tie from the handle.

073-00371-A | 13

iPhone 14 Pro
3. Turn the top knob on the fixture counterclockwise to raise the suction cup. Remove the packing foam.

Tools | Heated Display Removal Fixture

4. Turn the emergency stop knob clockwise until it clicks and protrudes from the stop guard.

5. Plug the power cord into the fixture. The fixture won't turn on until you flip the switch on the back.

073-00371-A | 14

iPhone 14 Pro
Battery Safety

Battery Safety

Warning
· This device contains a built-in lithium-ion rechargeable battery with soft battery cells. Battery safety is the number one concern when repairing a device with a built-in lithium-ion battery.
· Only technicians with the knowledge, experience, and tools required to repair electronic devices should replace a battery.
· Improper battery replacement, improper handling of parts, failure to discharge the battery before repair, or failure to follow the provided instructions could cause battery overheating, swelling, venting, leaking, or a battery thermal event. These events could result in fire, injury, death, data loss, or damage to the device, parts, or other property.
· To avoid these potentially harmful events, follow the battery safety guidelines and work in a safety-focused workspace with the tools listed below. It's important to be prepared for all possible outcomes.
How to set up a workspace for battery safety
Tools
· Clean, dry, untreated sand (810 cups) · Sand container (wide-mouthed, quick pour, nonbreakable plastic container with a flip-top lid) · Heat-resistant gloves · Safety glasses with side shields · ESD-safe cleaning solution
Workspaces used to repair Apple devices should meet the following criteria:
· Nonflammable and electrostatic discharge (ESD)-safe work bench · At least 2 feet away from paper and other combustible materials · Sand container within reach (2 feet) on one side of the workspace, not above the workspace · Adequate ventilation

073-00371-A | 15

iPhone 14 Pro

Battery Safety

Warning How to handle a battery thermal event
A battery thermal event is a rapid chemical chain reaction that occurs inside a battery cell. The energy stored in the battery is released suddenly, which can cause outgassing and fire. A battery thermal event can be triggered by physical damage to the battery, improper replacement or repair, or temperatures outside the battery's operating range.
Act immediately if you notice any of the following signs of a battery thermal event:
· The lithium-ion battery or a device that contains one begins to smoke or emit sparks or soot. · The battery pouch suddenly and quickly puffs out. · The lithium-ion battery or a device that contains one begins to emit hissing or popping sounds.
Do smother the battery or device immediately with plenty of clean, dry sand. Dump the sand all at once. Timing is critical -- the faster you pour all the sand, the sooner the reaction will be contained.
Do contact local fire authorities if further assistance is needed.
Do leave the room for 30 minutes after the reaction is contained. Ventilate the area. Don't return until the area is clear of smoke.
Do wait 30 minutes before touching the device. Wear the heat-resistant gloves and safety glasses with side shields to remove the device from the sand.
Do wipe the affected area with water first. Then wipe the area with an ESD-safe cleaning solution.
Do dispose of the damaged battery or device (including any debris removed from the sand) according to local environmental laws and guidelines.

073-00371-A | 16

iPhone 14 Pro
How to handle batteries

Battery Safety

Warning
Fully discharge the battery before you begin a repair. A discharged battery is less susceptible to a battery thermal event. If you can't determine the battery level, don't repair the device.
Perform the following steps to discharge the battery: · Disconnect all external cables. · Remove all cases and covers. · Turn on the flashlight from the Lock Screen, in Control Center, or by asking Siri. Wait until the device
has turned off and the flashlight is no longer illuminated.
Caution
The flashlight produces heat. Keep the iPhone in a well-ventilated area while the flashlight is illuminated.
Best practices · To avoid noxious fumes or a battery thermal event, don't puncture, strike, or crush a lithium-ion
battery or a device that contains one. · Keep your workspace clear of foreign objects and sharp materials. · Be careful when using sharp tools near the battery. · Don't leave loose screws, extra screws, or small parts inside the device. · Don't use tools that conduct electricity. · Don't throw or drop the battery. · Don't expose the battery to excessive heat or sunlight, or temperatures outside the battery's
operating range. · Handle and dispose of waste batteries in accordance with local laws and regulations.

073-00371-A | 17

iPhone 14 Pro
Broken Glass

Broken Glass

Warning
iPhone displays and some back covers are made of glass. The glass could break if the iPhone is dropped on a hard surface, receives a substantial impact, or is crushed, bent, or deformed. Don't attempt to remove chipped or cracked glass shards without protection.
Tools · Back protective cover · Cut-resistant gloves · Display protective cover · Heated display pocket · Safety glasses with side shields · Vacuum cleaner
If the iPhone glass is broken, perform the following steps before you begin a repair: 1. Put on safety glasses with side shields and the cut-resistant gloves. 2. Use a vacuum cleaner to remove glass pieces from your workspace and the iPhone. 3. Attach a protective cover to the broken glass to prevent injury or scattering of glass. Each protective
cover has a release liner underneath. Slowly pull the release liner out from under the protective cover while pressing the cover onto the enclosure. 4. Fold the release liner. Use the shiny side of the release liner to firmly press the protective cover onto the broken glass and smooth out any air bubbles.

5. Wait at least 12 minutes for the bond between the protective cover and the glass to strengthen. 6. If the back glass is broken, place the iPhone into the heated display pocket.

073-00371-A | 18

iPhone 14 Pro
If the iPhone has any of the following conditions, stop the repair: · There's no glass or insufficient glass for the protective cover to adhere to. · The protective cover doesn't adhere to the iPhone. · The iPhone doesn't fit in the heated display pocket.
You can find a service option at support.apple.com/repair.

Broken Glass

073-00371-A | 19

iPhone 14 Pro
First Steps

First Steps

Always perform the following steps before starting a repair: · Back up the iPhone. · Discharge the battery fully. · Turn off the iPhone. · Disconnect all cables. · Remove all cases and covers. · Clear and clean your workspace. · Put on an ESD wrist strap and attach it to a properly grounded ESD mat.
Caution
ESD (electrostatic discharge, or the release of static electricity) can damage electronic components.

Be aware of the following while performing a repair:
· The manual for this model may show images of other models, but the procedures are the same. Ensure that you use the correct tools for the model you're repairing.
· Take your time. Thoroughly read all instructions and alerts. · Magnetizing the torque drivers will make it easier to work with small screws. · The end of each flex cable must align with its connector. Press the end of each flex cable to its
connector until it clicks to ensure that it's secure.
Warning
Loose screws, extra screws, or small parts inside the device can damage the battery and cause safety issues. Set aside all parts and screws removed during the repair and account for them at the end of the repair.

073-00371-A | 20

iPhone 14 Pro
SIM Tray
Important
iPhone 14 models purchased in the United States don't have SIM trays.
Tools · SIM-eject tool or paper clip
Removal 1. Find your model to locate the SIM tray. 2. Insert a paper clip or SIM-eject tool into the hole next to the SIM tray. 3. Push the paper clip or SIM-eject tool toward the enclosure to eject the SIM tray. 4. Remove the SIM tray.
Reassembly 1. Press the SIM tray back into the side of the enclosure.

SIM Tray

073-00371-A | 21

iPhone 14 Pro
Display
Before You Begin

Display | Before You Begin

Warning · Read Battery Safety and follow workspace and battery handling guidelines before you begin. · Read Broken Glass before you begin.
Tools · 6.1-inch heated display pocket · 6.1-inch repair tray · Adhesive cutter · Display adhesive press plate · Display press · ESD-safe tweezers · Ethanol wipes or isopropyl alcohol (IPA) wipes · Heated display removal fixture · Heat-resistant gloves · Micro stix bit · Nylon probe (black stick) · Torque driver (gray, 0.55 kgf cm) · Torque driver (green, 0.45 kgf cm) · Torx security bit

073-00371-A | 22

iPhone 14 Pro
Caution
To avoid damaging the lenses, don't touch the TrueDepth camera assembly or nearby parts.

Display | Before You Begin

Caution
· Don't touch the back of the display. Touching the back of the display may affect image quality. · This procedure requires System Configuration. After you've completed all removal and
reassembly steps, follow the instructions to initiate System Configuration.
Important
Read Heated Display Removal Fixture if you're setting up the fixture for the first time.

073-00371-A | 23

iPhone 14 Pro

Display | Removal

Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Use a torque driver and the Torx security bit to remove the two security screws, one from each side of the Lightning connector. Set aside the screws.

3. Flip the switch on the back of the heated display removal fixture to turn it on. The internal fan will turn on. Wait for a checkmark to appear on the screen.
Note: If an error code appears on the screen, turn off the fixture and turn it back on.

073-00371-A | 24

iPhone 14 Pro
4. Take the iPhone out of the repair tray. Gently insert the iPhone into the heated display pocket with the display faceup and the Lightning connector facing the bottom of the pocket.
Caution
Ensure that you don't scratch the iPhone as you insert it into the heated display pocket.
Important
Ensure that the clamp on the side of the pocket is flipped up.
5. Flip down the clamp on the side of the pocket to lock the iPhone into place.

Display | Removal

073-00371-A | 25

iPhone 14 Pro
6. Put on the heat-resistant gloves. Align the cutout on the bottom of the pocket with the rail on the fixture. Slide the pocket with the iPhone onto the rail on the fixture.
Warning
Don't insert the pocket into the fixture without wearing the heat-resistant gloves.

Display | Removal

073-00371-A | 26

iPhone 14 Pro
7. Slide the pocket into the fixture until the pocket clicks into place.
Note: The screen on the fixture will turn red and the timer will count down from 2 minutes while the pocket heats to the correct temperature. When the timer shows 0, the fixture will start to beep and the screen will turn green.

Display | Removal

073-00371-A | 27

iPhone 14 Pro
8. Turn the knob on the fixture clockwise to lower the suction cup as close to the iPhone as possible without touching the iPhone.
Caution
To avoid damaging the iPhone, don't turn the knob before the timer shows 0, the fixture beeps, and the screen has turned green. Note: The fixture will beep until the suction cup is lowered.
9. Grasp the handle and slide the suction cup straight out until the edge of the suction cup aligns with the bottom edge of the display.
Caution
Failure to align the edges of the suction cup and the display may damage the iPhone.
© 2023 Apple Inc. All rights reserved.

Display | Removal 073-00371-A | 28

iPhone 14 Pro
10. Turn the knob on the fixture clockwise to lower the suction cup onto the display (1). Then flip down the handle on the suction cup to secure the suction cup to the display (2).
Important
Once the suction cup is lowered onto the iPhone, the screen will begin a 15-minute countdown. When the timer shows 0, the heated display removal fixture will turn off. Ensure that you complete steps 11 and 12 within this time frame.
11. Slowly turn the knob on the fixture counterclockwise until the display begins to separate from the enclosure.
Important
If you don't see a gap between the display and the enclosure immediately, wait 30 seconds. If you still don't see a gap, turn the silver part of the knob counterclockwise until the display begins to separate from the enclosure.
© 2023 Apple Inc. All rights reserved.

Display | Removal 073-00371-A | 29

iPhone 14 Pro
12. Insert the edge of the adhesive cutter between the display and the enclosure. Run the cutter between the display and the enclosure to the right and left as shown until the display partially releases from the enclosure.

Display | Removal

Caution
To avoid damaging the display flex connectors, don't tilt up the bottom of the display more than 5 degrees.
© 2023 Apple Inc. All rights reserved.

073-00371-A | 30

iPhone 14 Pro
13. Flip up the handle to release the suction cup (1). Gently slide the flat end of the black stick under the edge of the suction cup to release it from the display (2).
Caution
Don't turn the knob. Turning the knob may damage the flex cables.
14. Press the eject button on the side of the pocket to release the pocket from the fixture.

Display | Removal

073-00371-A | 31

iPhone 14 Pro
15. Hold both sides of the pocket and slide it straight out of the fixture.
16. Flip up the clamp on the side of the pocket to release the iPhone (1). Hold the area outlined in blue and gently remove the iPhone from the pocket (2).
Caution
Don't scratch the iPhone as you remove it from the heated display pocket.
© 2023 Apple Inc. All rights reserved.

Display | Removal 073-00371-A | 32

iPhone 14 Pro

Display | Removal

17. Place the iPhone into the repair tray with the display faceup and the Lightning connector facing the cutout. Remove the gloves.

18. Slide the display slightly toward the bottom of the iPhone.
19. Insert the edge of the adhesive cutter into the top of the iPhone between the display and the enclosure. Hold the adhesive cutter at a 45-degree angle. Cut along the top and sides of the iPhone until the display is free.
Caution
To avoid damaging the display flex cables, don't tilt up the bottom of the display more than 5 degrees.

20. Insert the repair tray suction cups into the slots in the repair tray.

073-00371-A | 33

iPhone 14 Pro
21. Tilt up the display toward the suction cups. Press the top and bottom edges of the display to secure it to the suction cups.
Note: The icon on the bottom of the repair tray shows the correct direction to tilt up the display.
Caution
· To avoid damaging the enclosure or display, ensure that the internal display clips are released before you tilt up the display.
· Don't damage the flex cables as you tilt up the display.

Display | Removal

Warning
If the battery is dented, punctured, or otherwise damaged, stop the repair. You can find a service option at support.apple.com/repair.

22. Use a torque driver and Micro stix bit to remove the eight trilobe screws from the logic board cowling. Set aside the screws.

073-00371-A | 34

iPhone 14 Pro
23. Use ESD-safe tweezers to slightly lift the logic board cowling. Ensure that the bottom tab on the logic board cowling clears the display flex cable as you lift it.
24. Use ESD-safe tweezers to slide the logic board cowling out from under the ambient light sensor flex cable (1). Then lift the cowling out of the enclosure (2). Save the cowling for reassembly.
Caution
Don't tear the ambient light sensor flex cable while removing the cowling.
© 2023 Apple Inc. All rights reserved.

Display | Removal 073-00371-A | 35

iPhone 14 Pro
25. Use the black stick to lift the end of the battery flex cable (1) off the connector.
Caution
You must disconnect the battery flex cable first to ensure that the iPhone stays turned off.
26. Use the black stick to lift the ends of the display flex cable (2) and the ambient light sensor cable (3) off the connectors.

Display | Removal

27. Hold the display by the edges. Pull the tabs on the suction cups to release them from the display. Then set the display facedown on a clean, flat surface.
28. Remove the suction cups from the repair tray.
29. Use ESD-safe tweezers to pick up the adhesive. Then pull the adhesive at 45-degree angle as shown to remove it from the enclosure. Repeat this process until all the adhesive is removed from the perimeter of the enclosure.
Caution
Don't touch the TrueDepth camera assembly, grounding springs, or nearby parts.

073-00371-A | 36

iPhone 14 Pro

Display | Removal

30. Use ethanol wipes or IPA wipes to clean all residual adhesive from the enclosure.

Caution
Don't use ethanol wipes or IPA wipes on the display. Ethanol or isopropyl alcohol may damage the display and affect image quality.

073-00371-A | 37

iPhone 14 Pro

Display | Reassembly

Reassembly
1. Inspect the internal display clips for damage before reassembly. Ensure that the internal display clips are at a 90-degree angle and aren't bent or damaged.
Important
· If the internal display clips are damaged, you may need to replace the display. · If you're installing a replacement display, peel the protective liner from the top and underside.

2. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

3. Inspect the TrueDepth camera. Ensure that the top edge of the TrueDepth camera is under the lip of the enclosure.
Caution
If the TrueDepth camera is positioned incorrectly, use the black stick to move it into the correct position.

Warning
Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

073-00371-A | 38

iPhone 14 Pro
4. Inspect the two pieces of foam on the top speaker grille. If either piece is missing or damaged, continue to step 5. If the foam is intact, skip to step 9.
5. Use ESD-safe tweezers to remove the top speaker grille from the enclosure.

Display | Reassembly

073-00371-A | 39

iPhone 14 Pro
6. Use ESD-safe tweezers to peel the adhesive liner off the back of the replacement top speaker grille.
7. Position the replacement top speaker grille in the cutout on the lip of the enclosure. Ensure that the adhesive side of the speaker grille faces the side of the enclosure.

Display | Reassembly

073-00371-A | 40

iPhone 14 Pro
8. Position the tip of the ESD-safe tweezers in the middle of the top speaker grille. Slightly move the tweezers from side to side to ensure that the speaker grille is firmly adhered to the enclosure and doesn't move.

Display | Reassembly

073-00371-A | 41

iPhone 14 Pro

Display | Reassembly

9. Align the replacement display adhesive over the enclosure. Ensure that the top holes of the adhesive align over the TrueDepth camera assembly.

Caution
Ensure that you've removed all adhesive residue from the display and the enclosure before you apply the replacement display adhesive.

10. The replacement display adhesive has a top release liner, a middle release liner, and a flexible bottom release liner. Grasp the tab on the bottom release liner. Then slowly pull the bottom release liner (1) out from under the adhesive (2) while pressing the adhesive onto the enclosure.
Important
Don't remove the top release liner yet.

Bottom release liner
Adhesive
Note: The replacement display adhesive for your model may look different from the illustration, but the steps are the same.
© 2023 Apple Inc. All rights reserved.

073-00371-A | 42

iPhone 14 Pro

Display | Reassembly

11. Inspect the adhesive to ensure that it's positioned on the lip of the enclosure. If the adhesive isn't correctly positioned, repeat removal steps 29 and 30. Then repeat reassembly steps 1 through 10.

12. Place the display adhesive press plate on top of the enclosure with the icon in the top right corner as shown.

13. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.
© 2023 Apple Inc. All rights reserved.

073-00371-A | 43

iPhone 14 Pro
14. Wait until the display press beeps and the timer shows 0. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).
Caution
To ensure that the display adhesive bonds correctly to the enclosure, don't lift the lever until 30 seconds have passed.

Display | Reassembly

15. Remove the repair tray from the display press and remove the press plate.

073-00371-A | 44

iPhone 14 Pro
16. Remove the left section of the top release liner first (1). Then remove the three sections running along the top (2), right (3), and bottom (4).
Important
Don't remove the middle release liner yet.

Display | Reassembly

Top release liner
17. Insert the suction cups into the repair tray. 18. Align the left edge of the display with the left edge of the enclosure. Gently press along the edges of
the display to secure it to the suction cups.

073-00371-A | 45

iPhone 14 Pro
19. Press the ends of the ambient light sensor flex cable (1) and display flex cable (2) to the connectors. Press evenly along the length of each connector.
20. Press the end of the battery flex cable (3) to the connector. Press evenly along the length of the connector.
21. Use ESD-safe tweezers to slide the top tab of the logic board cowling behind the ambient light sensor flex cable (1). Then slide the edge of the cowling under the tab on the side of the enclosure (2) and slide the bottom tab behind the display flex cable (3). Lower the cowling over the ends of the flex cables.
© 2023 Apple Inc. All rights reserved.

Display | Reassembly 073-00371-A | 46

iPhone 14 Pro
22. Use the green torque driver and Micro stix bit to install the following eight new trilobe screws into the logic board:
· One trilobe screw (923-08156) (1)
· Two trilobe screws (923-08157) (2)
· Five trilobe screws (923-08155) (3)

Display | Reassembly

073-00371-A | 47

iPhone 14 Pro
23. Peel the first strip from the middle release liner (1) clockwise, starting at the bottom right of the enclosure. Peel the second strip (2) counterclockwise, starting near the bottom right of the enclosure. Peel the third strip (3) clockwise, starting at the bottom left of the enclosure.
Caution
The third strip of the middle release liner runs under two flex cables. Don't damage the flex cables while removing the release liner.

Display | Reassembly

Middle release liner
24. Inspect the display adhesive to ensure that it's in the correct position and isn't damaged or wrinkled. If the adhesive is damaged, remove it and apply replacement adhesive.

073-00371-A | 48

iPhone 14 Pro
25. Inspect the TrueDepth camera. Ensure that the top edge of the TrueDepth camera is under the lip of the enclosure.
Caution
If the TrueDepth camera is positioned incorrectly, use the black stick to move it into the correct position.

Display | Reassembly

Warning
Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

26. Pull the tabs on the suction cups to release them from the display. Tilt down the display to rest on the enclosure.
27. Remove the suction cups from the repair tray.

073-00371-A | 49

iPhone 14 Pro
28. Press all four corners of the display simultaneously. Then press along the edges of the display until the display clicks into place and is flush with the enclosure.

Display | Reassembly

Caution
Ensure that the flex cables aren't trapped between the display and enclosure. Feel the edges of the display for variations or gaps. If the display isn't flush, repeat all removal steps and check the flex cables for damage. Then repeat reassembly steps 1 through 28.

Raised edges Edges in correct position

073-00371-A | 50

iPhone 14 Pro
29. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

Display | Reassembly

30. Wait until the display press beeps and the timer shows 0. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

073-00371-A | 51

iPhone 14 Pro
31. Remove the repair tray from the display press.
32. Use the gray torque driver and Torx security bit to install two new security screws, one on each side of the Lightning connector. As you install the screws, press lightly on the display near the Lightning connector. Count five clicks as you install each screw to ensure that the screws are fully installed.
Note: Use the correct screw color for your model. · Deep purple (923-08431) · Gold (923-08430) · Silver (923-08429) · Space black (923-08428)
Caution
If the screws aren't flush, then remove and set aside the screws. Repeat step 32 to install another new set of screws. If the new screws still aren't flush, repeat all removal and reassembly steps.

Display | Reassembly

073-00371-A | 52

iPhone 14 Pro

Display | Reassembly

Caution
· System Configuration is required if you've installed a replacement battery, display, camera, or TrueDepth camera. Disregard notifications about iPhone features on the Lock Screen until you complete System Configuration.
· After you've completed all removal and reassembly steps, initiate System Configuration. The method of initiating System Configuration will vary depending on the part or parts replaced. · If you replaced the battery, or display, initiate System Configuration by putting the device into diagnostics mode. Tap Start Diagnostics and follow the onscreen prompts. · If you replaced the camera, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.
· If you replaced the TrueDepth camera, you will need the following: · The latest version of Apple Service Utility installed on a Mac running macOS 12.4 or later · Internet access · A Lightning cable
After you've installed Apple Service Utility on a Mac, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

073-00371-A | 53

iPhone 14 Pro
Camera
Before You Begin

Camera | Before You Begin

Warning
Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Remove the following part before you begin:
· Display

Tools
· 6.1-inch repair tray · ESD-safe tweezers · JCIS bit · Micro stix bit · Nitrile or lint-free gloves · Nylon probe (black stick) · Torque driver (black, 0.35 kgf cm) · Torque driver (green, 0.45 kgf cm) · Torque driver (teal, 0.75 kgf cm)

073-00371-A | 54

iPhone 14 Pro
Caution
· To avoid damaging the lenses, don't touch the TrueDepth camera assembly or nearby parts.
· Avoid the grounding spring on the camera cowling.

Camera | Before You Begin

Caution
This procedure requires System Configuration. After you've completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

073-00371-A | 55

iPhone 14 Pro

Camera | Removal

Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout. 2. Put on the gloves to prevent contamination of the camera lenses.

3. Use a torque driver and the Micro stix bit to remove the five trilobe screws (1) from the camera cowling. Set aside the screws.
4. Use a torque driver and the JCIS bit to remove the crosshead screw from the camera cowling (2). Set aside the screw.

5. Use ESD-safe tweezers to tilt up the camera cowling from the left side (1). Then slide the cowling tab out of the slot on the right side of the enclosure (2). Save the cowling for reassembly.

073-00371-A | 56

iPhone 14 Pro
6. Position the ESD-safe tweezers under the top left corner of the top camera flex cable as shown. Then gently lift the end of the top camera flex cable off the connector. Note: One camera flex cable covers the other.
Caution
Ensure that you position the ESD-safe tweezers as shown to avoid damaging the top camera flex cable.
7. Position the ESD-safe tweezers under the bottom left corner of the bottom camera flex cable as shown. Then gently lift the end of the bottom camera flex cable off the connector.
Caution
Ensure that you position the ESD-safe tweezers as shown to avoid damaging the bottom camera flex cable.
© 2023 Apple Inc. All rights reserved.

Camera | Removal 073-00371-A | 57

iPhone 14 Pro
8. Gently hold the camera flex cables together and lift the camera out of the enclosure.

Camera | Removal

073-00371-A | 58

iPhone 14 Pro

Camera | Reassembly

Reassembly
1. Put on the gloves to prevent contamination of the camera lenses. Then hold the replacement camera with the lenses facedown and remove the protective cover from the camera lenses.

2. Hold the camera flex cables together. Then position the camera in the enclosure.

3. Press the end of the bottom camera flex cable to the connector. 4. Press the end of the top camera flex cable to the connector. 5. Lightly press the camera into the enclosure.

073-00371-A | 59

iPhone 14 Pro
6. The camera cowling has a tab that fits into a slot under the lip on the right side of the enclosure. Hold the cowling with ESD-safe tweezers and slide the cowling tab into the slot. Then lower the cowling onto the camera.
Caution
· Ensure that the screw cutouts in the camera cowling align with the screw holes, and the tab is inside the slot in the enclosure. A misaligned cowling may affect display image quality.
· Ensure that the grounding spring on the camera cowling isn't damaged. Avoid touching the grounding spring as you reinstall the cowling.

Camera | Reassembly

073-00371-A | 60

iPhone 14 Pro
7. Use the black torque driver and Micro stix bit to install four new trilobe screws (923-08160) (1) into the camera cowling.
8. Use the teal torque driver and JCIS bit to install one crosshead screw (923-08375) (2) into the camera cowling.
9. Use the green torque driver and Micro stix bit to install one new Micro stix screw (923-08376) (3) into the camera cowling.

Camera | Reassembly

Reinstall the following part to complete reassembly: · Display
Caution
After you've completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

073-00371-A | 61

iPhone 14 Pro

Camera | Reassembly

During System Configuration, you will perform LiDAR Scanner calibration. Prepare for calibration by reviewing the following steps:

1. Use a well-lit area containing objects of different shapes and sizes.
2. Sit or stand 1 to 2 feet from the objects.
3. Hold the device vertically and rest your elbow on your body to help stabilize your arm.

4. Start scanning by slowly panning back and forth to the left and right of the starting point. Follow the directions that appear on the device screen.

Note: The calibration process takes approximately 5 minutes.

073-00371-A | 62

iPhone 14 Pro
Bottom Speaker
Before You Begin

Bottom Speaker | Before You Begin

Warning
Read Battery Safety and follow workspace and battery handling guidelines before you begin.
Remove the following part before you begin: · Display

Tools
· 6.1-inch repair tray · ESD-safe tweezers · JCIS bit · Nylon probe (black stick) · Torque driver (gray, 0.55 kgf cm)

Caution
Avoid touching the grounding springs on the bottom speaker.

073-00371-A | 63

iPhone 14 Pro

Bottom Speaker | Removal

Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Use a torque driver and the JCIS bit to remove the four crosshead screws from the bottom speaker. Set aside the screws.

3. Slightly tilt up the bottom speaker as shown (1). Run the flat end of the black stick between the battery shim and the Taptic Engine and bottom speaker to loosen the adhesive on the battery shim (2).

073-00371-A | 64

iPhone 14 Pro
Reassembly 1. Rotate the repair tray.
Ensure that the rubber gasket is positioned as shown. If the gasket is out of position, use ESD-safe tweezers to reposition it.
2. Rotate the repair tray. Align the port on the bottom speaker with the rubber gasket. Then position the bottom speaker in the enclosure.

Bottom Speaker | Reassembly

073-00371-A | 65

iPhone 14 Pro
3. Use the gray torque driver and JCIS bit to install four new crosshead screws (923-08147) (1) (923-08377) (2) into the bottom speaker.
Caution
Don't damage the grounding springs on the speaker.

Bottom Speaker | Reassembly

Reinstall the following part to complete reassembly: · Display

073-00371-A | 66

iPhone 14 Pro
Taptic Engine
Before You Begin

Taptic Engine | Before You Begin

Warning
Read Battery Safety and follow workspace and battery handling guidelines before you begin.
Remove the following parts before you begin: · Display · Bottom speaker

Tools
· 6.1-inch repair tray · ESD-safe tweezers · JCIS bit · Nylon probe (black stick) · Super screw bit · Torque driver (blue, 0.65 kgf cm) · Torque driver (teal, 0.75 kgf cm)

073-00371-A | 67

iPhone 14 Pro

Taptic Engine | Removal

Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Use a torque driver and the super screw bit to remove the super screw from the Taptic Engine. Set aside the screw.

3. Use a torque driver and the JCIS bit to remove the two crosshead screws from the Taptic Engine. Set aside the screws.

073-00371-A | 68

iPhone 14 Pro
4. Lift the end of the Taptic Engine flex cable off the connector.
5. Remove the Taptic Engine and battery shim from the enclosure.

Taptic Engine | Removal

073-00371-A | 69

iPhone 14 Pro
Reassembly
1. If you're reinstalling the existing Taptic Engine, keep the battery shim attached. If you're installing a replacement Taptic Engine, peel the battery shim off the original Taptic Engine and adhere it to the replacement.

Taptic Engine | Reassembly

2. Position the Taptic Engine and battery shim in the enclosure.
3. Press the end of the Taptic Engine flex cable to the connector.

073-00371-A | 70

iPhone 14 Pro
4. Use the blue torque driver and super screw bit to install one new super screw (923-08151) into the Taptic Engine.
5. Use the teal torque driver and JCIS bit to install two new crosshead screws (923-08149) (1) (923-08374) (2) into the Taptic Engine.

Taptic Engine | Reassembly

Reinstall the following parts to complete reassembly: · Bottom speaker · Display

073-00371-A | 71

iPhone 14 Pro
Battery
Before You Begin

Battery | Before You Begin

Warning
· A battery should be replaced only by individual technicians with the knowledge and experience to repair electronic devices. Improper battery replacement, improper handling of parts, or failure to follow the provided instructions could result in fire, injury, data loss, or damage to the device, parts, or other property.
· Read Battery Safety and follow workspace and battery handling guidelines before you begin.
Remove the following parts before you begin:
· Display · Bottom speaker · Taptic Engine

Tools
· 6.1-inch repair tray · Battery press · ESD-safe cleaning solution · ESD-safe tweezers · Ethanol wipes or isopropyl alcohol (IPA) wipes · Heat-resistant gloves · Nylon probe (black stick) · Safety glasses with side shields · Sand · Sand container

073-00371-A | 72

iPhone 14 Pro
Caution
To avoid damaging the lenses, don't touch the TrueDepth camera assembly or nearby parts.

Battery | Before You Begin

Caution
This procedure requires System Configuration. After you've completed all removal and reassembly steps, follow the instructions to initiate System Configuration.

073-00371-A | 73

iPhone 14 Pro

Battery | Removal

Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

2. Use ESD-safe tweezers to grasp the bottom left battery adhesive tab. Gently peel the adhesive tab away from the battery.
Note: The battery has three adhesive tabs.

073-00371-A | 74

iPhone 14 Pro
3. Hold down the iPhone. Use ESD-safe tweezers to continue peeling the adhesive tab from the battery.
Important
Peel the adhesive tab completely from the battery before twisting it around the tweezers.
4. Keep the tweezers close and parallel to the battery and twist until you see white adhesive strip on the tweezers.
Important
Don't pull the tweezers until the white adhesive is wrapped around them.
© 2023 Apple Inc. All rights reserved.

Battery | Removal 073-00371-A | 75

iPhone 14 Pro

Battery | Removal

5. Pull the tweezers toward the Lightning connector at the bottom of the iPhone and continue to twist the adhesive until you've removed the entire strip.

Caution
Don't pull the adhesive strip against parts or screws.

Important
If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat steps 4 and 5. If you can't see the tab or strip, continue to step 6.

6. Use ESD-safe tweezers to grasp the bottom right battery adhesive tab. Gently peel the adhesive tab away from the battery.
7. Repeat steps 3 through 5 to remove the bottom right adhesive strip from the battery. If you remove the entire strip, continue to step 8.
Important
If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat steps 4 and 5. If you can't see the tab or strip, continue to step 8.

8. Rotate the repair tray.

073-00371-A | 76

iPhone 14 Pro
9. Hold down the iPhone. Use ESD-safe tweezers to gently peel the battery adhesive tab from the top of the battery.
10. Twist the tweezers to wrap the adhesive tab around them.
Important
Hold the tweezers close and parallel to the battery as you twist.

Battery | Removal

073-00371-A | 77

iPhone 14 Pro
11. Keep the tweezers close to the channel between the battery and the camera cowling. Continue to slowly twist the tweezers until you've removed the entire adhesive strip.
Important
If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat step 11. If you can't see the tab or strip, continue to step 12.

Battery | Removal

12. If all three battery adhesive strips were fully removed, continue to step 14. If at least one strip was fully removed, continue to step 13.
Warning
If all three strips were broken and can't be retrieved, don't forcibly pry the battery. Stop the repair. You can find a service option at support.apple.com/repair.

073-00371-A | 78

iPhone 14 Pro
Caution
When using the black stick to remove the battery from the enclosure, don't damage the flex cables. Don't scrape, rip, tear, or otherwise damage the polyester film or other areas. If damage occurs, replace the iPhone.
13. Insert the flat end of the black stick only into one of the insertion points as shown. Ensure that the black stick is inserted into a point where the battery strip has been fully removed. Don't insert the black stick into a point where the battery tab or strip is broken.
© 2023 Apple Inc. All rights reserved.

Battery | Removal 073-00371-A | 79

iPhone 14 Pro

Battery | Removal

14. Slightly lift the battery with the black stick just enough to grasp underneath the battery.

Caution
To avoid damage, don't press the black stick on the edge of the enclosure as you lift the battery.

15. Remove the battery from the enclosure. Then inspect the enclosure for damage. If the enclosure is damaged, replace the iPhone.
Warning
If you can't remove the battery, stop the repair. You can find a service option at support.apple.com/repair.

073-00371-A | 80

iPhone 14 Pro
Reassembly 1. Reinstall the Taptic Engine. 2. Reinstall the bottom speaker.
3. Use ethanol wipes or IPA wipes on the area shown in blue to remove any remaining adhesive from the enclosure.
Caution
Don't use ethanol wipes or IPA wipes on the areas outlined in red. Ethanol or isopropyl alcohol may damage the polyester film and wireless charging unit.
Warning
Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.
© 2023 Apple Inc. All rights reserved.

Battery | Reassembly 073-00371-A | 81

iPhone 14 Pro
4. Peel the pink release liner from the underside of the replacement battery.
Important
Don't remove the battery protective cover from the top of the battery yet.
5. Hold the battery over the enclosure with the protective cover faceup. Align the bottom of the battery with the bottom speaker (1) and the right edge with the enclosure (2). Then lower the battery into the enclosure. Note: The protective cover for your replacement battery may look different, but the steps are the same.
© 2023 Apple Inc. All rights reserved.

Battery | Reassembly 073-00371-A | 82

iPhone 14 Pro
6. The center of the repair tray has two slots. Position the repair tray and enclosure onto the battery press with the left slot over the pin as shown.
7. Flip down the red lever at the top of the battery press to lower the roller onto the battery.

Battery | Reassembly

073-00371-A | 83

iPhone 14 Pro
8. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.
9. Flip up the lever. 10. Position the repair tray and
enclosure onto the battery press with the right slot over the pin.

Battery | Reassembly

11. Flip down the lever.
12. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.
13. Flip up the lever.

073-00371-A | 84

iPhone 14 Pro
14. Remove the repair tray from the battery press.
15. Hold the edges of the battery protective cover. Pull the release tabs on the protective cover to remove it from the battery.
Important
Don't press the area over the tab you're releasing.

Battery | Reassembly

Reinstall the following part to complete reassembly: · Display
Warning
Gently shake the iPhone. If the battery sounds loose, remove the display and the battery. Then complete battery reassembly with another replacement battery.
Important
A new battery is not charged. After you've completed all removal and reassembly steps, charge the device for a few minutes.
Caution
After you've completed all removal and reassembly steps, initiate System Configuration by putting the device into diagnostics mode. Tap Start Diagnostics and follow the onscreen prompts.

073-00371-A | 85

iPhone 14 Pro
Top Speaker
Before You Begin

Top Speaker | Before You Begin

Warning
Read Battery Safety and follow workspace and battery handling guidelines before you begin.
Remove the following part before you begin: · Display

Tools
· 6.1-inch repair tray · ESD-safe tweezers · JCIS bit · Nitrile or lint-free gloves · Nylon probe (black stick) · Torque driver (gray, 0.55 kgf cm)

Caution
· To avoid damaging the lenses, don't touch the TrueDepth camera assembly or nearby parts.
· Avoid the grounding spring on the camera cowling.

073-00371-A | 86

iPhone 14 Pro

Top Speaker | Removal

Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout. 2. Put on the gloves to prevent contamination of the camera lenses.

3. Use a torque driver and the JCIS bit to remove the two crosshead screws from the top speaker. Set aside the screws.

4. Use the black stick to tilt up the top speaker as shown. Then lift the top speaker out of the enclosure.

073-00371-A | 87

iPhone 14 Pro
Reassembly 1. Position the top speaker in the enclosure.
2. Use the gray torque driver and JCIS bit to install two new crosshead screws (923-08159) into the top speaker.

Top Speaker | Reassembly

Reinstall the following part to complete reassembly: · Display

073-00371-A | 88

iPhone 14 Pro
TrueDepth Camera
Before You Begin

TrueDepth Camera | Before You Begin

Warning · Read Battery Safety and follow workspace and battery handling guidelines before you begin. · The TrueDepth camera includes one or more lasers. Disassembly of the TrueDepth camera,
damage to the TrueDepth camera, or failure to use genuine Apple parts could expose you to hazardous infrared laser emissions, possibly resulting in injuries to eyes or skin.
Remove the following parts before you begin: · Display · Top speaker

Tools
· 6.1-inch repair tray · ESD-safe tweezers · Nitrile or lint-free gloves · Nylon probe (black stick)

Caution
This procedure requires System Configuration. To perform System Configuration you will need the following:
· The latest version of Apple Service Utility installed on a Mac running macOS Monterey 12.4 or later
· Internet access · A Lightning cable After you've completed all removal and reassembly steps and installed Apple Service Utility on a Mac, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.

073-00371-A | 89

iPhone 14 Pro

TrueDepth Camera | Removal

Removal 1. Place the enclosure in the repair tray with the Lightning connector facing the cutout. 2. Put on the gloves to prevent contamination of the camera lenses.

3. Use ESD-safe tweezers to lift the ends of the two TrueDepth camera flex cables off the connectors.

4. Gently hold the TrueDepth camera flex cables together and lift the TrueDepth camera out of the enclosure.

073-00371-A | 90

iPhone 14 Pro

TrueDepth Camera | Reassembly

Reassembly 1. Put on the gloves to prevent contamination of the camera lenses.
2. Inspect the TrueDepth camera assembly to ensure that the grounding foam and grounding springs are intact. If either is missing or damaged, replace the TrueDepth camera assembly.

3. Position the TrueDepth camera in the enclosure.
Caution
Don't remove the protective covers yet.

4. Reinstall the top speaker.
5. Remove the protective covers from the TrueDepth camera.
6. Inspect the TrueDepth camera assembly. Ensure that the top edge of the camera assembly is under the lip of the enclosure.
Caution
· If the TrueDepth camera is positioned incorrectly, use the black stick to move it into the correct position.
· Don't touch the front of the TrueDepth camera assembly after the protective covers are removed.

073-00371-A | 91

iPhone 14 Pro
Reinstall the following part to complete reassembly: · Display

TrueDepth Camera | Reassembly

Caution
· After you've completed all removal and reassembly steps, learn how to initiate the System Configuration process at support.apple.com/self-service-repair.
· You will need a Mac with Apple Service Utility installed to perform System Configuration.

Micro stix® is a registered trademark of OSG CORPORATION. Torx® is a registered trademark of Acument Intellectual Properties, LLC.

073-00371-A | 92

Adobe InDesign 18.1 (Macintosh) Adobe PDF Library 17.0