Xiaomi Communications Co., Ltd. C3IH Mobile Phone (LTE/WCDMA/GSM/BT/WIFI) 2AFZZC3IH 2AFZZC3IH c3ih
SAR TEST REPORT Applicant Xiaomi Communications Co., Ltd. FCC ID 2AFZZC3IH Product Mobile Phone Brand Redmi Model M1908C3IH Report No. R1907A0375-S1V1 Issue Date September 2, 2019 TA Technology (Shanghai) Co., Ltd. tested the above equipment in accordance with the requirements in IEEE 1528- 2013, ANSI C95.1: 1992/IEEE C95.1: 1991. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Performed by: Yu Wang Approved by: Guangchang Fan TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China TEL: +86-021-50791141/2/3 FAX: +86-021-50791141/2/3-8000 FCC SAR Test Report Report No.: R1907A0375-S1V1 Table of Contents 1 Test Laboratory............................................................................................................................... 4 1.1 Notes of the Test Report ......................................................................................................... 4 1.2 Test facility .............................................................................................................................. 4 1.3 Testing Location ...................................................................................................................... 5 1.4 Laboratory Environment .......................................................................................................... 5 2 Statement of Compliance ............................................................................................................... 6 3 Description of Equipment under Test.............................................................................................. 7 4 Test Specification, Methods and Procedures ................................................................................. 9 5 Operational Conditions during Test .............................................................................................. 10 5.1 Test Positions........................................................................................................................ 10 5.1.1 Against Phantom Head ................................................................................................... 10 5.1.2 Body Worn Configuration................................................................................................ 10 5.1.3 Phablet SAR test considerations ................................................................................... 11 5.2 Measurement Variability ........................................................................................................ 12 5.3 Test Configuration ................................................................................................................. 13 5.3.1 GSM Test Configuration .................................................................................................. 13 5.3.2 UMTS Test Configuration................................................................................................ 13 5.3.3 LTE Test Configuration .................................................................................................... 17 5.3.4 Additional requirements for TDD LTE specification .................................................... 18 5.3.5 Wi-Fi Test Configuration.................................................................................................. 21 5.3.6 BT Test Configuration ..................................................................................................... 22 6 SAR Measurements System Configuration .................................................................................. 23 6.1 SAR Measurement Set-up .................................................................................................... 23 6.2 DASY5 E-field Probe System ................................................................................................ 24 6.3 SAR Measurement Procedure .............................................................................................. 25 7 Main Test Equipment .................................................................................................................... 27 8 Tissue Dielectric Parameter Measurements & System Verification .............................................. 29 8.1 Tissue Verification ................................................................................................................. 29 8.2 System Performance Check.................................................................................................. 30 9 Normal and Maximum Output Power ........................................................................................... 32 9.1 GSM Mode ............................................................................................................................ 32 9.2 WCDMA Mode ...................................................................................................................... 34 9.3 LTE Mode.............................................................................................................................. 35 9.4 WLAN Mode .......................................................................................................................... 53 9.5 Bluetooth Mode ..................................................................................................................... 54 10 Measured and Reported (Scaled) SAR Results ........................................................................... 55 10.1 EUT Antenna Locations ........................................................................................................ 55 10.2 Standalone SAR test exclusion considerations ..................................................................... 57 10.3 Measured SAR Results ......................................................................................................... 58 10.4 Simultaneous Transmission Analysis .................................................................................... 75 11 Measurement Uncertainty ............................................................................................................ 78 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 2 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 ANNEX A: Test Layout......................................................................................................................... 79 ANNEX B:The EUT Appearances and Test Configuration ................................................................... 81 ANNEX C: System Check Results....................................................................................................... 81 ANNEX D: Highest Graph Results....................................................................................................... 81 ANNEX E: Calibration Certificate......................................................................................................... 81 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 3 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 1 Test Laboratory 1.1 Notes of the Test Report This report shall not be reproduced in full or partial, without the written approval of TA technology (shanghai) co., Ltd. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein .Measurement Uncertainties were not taken into account and are published for informational purposes only. This report is written to support regulatory compliance of the applicable standards stated above. 1.2 Test facility FCC (Designation number: CN1179, Test Firm Registration Number: 446626) TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. IC (recognition number is 8510A) TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. VCCI (recognition number is C-4595, T-2154, R-4113, G-10766) TA Technology (Shanghai) Co., Ltd. has been listed by industry Japan to perform electromagnetic emission measurement. A2LA (Certificate Number: 3857.01) TA Technology (Shanghai) Co., Ltd. has been listed by American Association for Laboratory Accreditation to perform electromagnetic emission measurement. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 4 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 1.3 Testing Location Report No.: R1907A0375-S1V1 Company: Address: City: Post code: Country: Contact: Telephone: Fax: Website: E-mail: TA Technology (Shanghai) Co., Ltd. No.145, Jintang Rd, Tangzhen Industry Park, Pudong Shanghai, China Shanghai 201201 P. R. China Xu Kai +86-021-50791141/2/3 +86-021-50791141/2/3-8000 http://www.ta-shanghai.com xukai@ta-shanghai.com 1.4 Laboratory Environment Temperature Min. = 18C, Max. = 25 C Relative humidity Min. = 30%, Max. = 70% Ground system resistance < 0.5 Ambient noise is checked and found very low and in compliance with requirement of standards. Reflection of surrounding objects is minimized and in compliance with requirement of standards. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 5 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 2 Statement of Compliance The maximum results of Specific Absorption Rate (SAR) found during testing for the EUT are as follows: Table 1: Highest Reported SAR Mode Highest Reported SAR (W/kg) 1g SAR Head 1g SAR Body-worn 1g SAR Hotspot GSM 850 0.017 0.284 0.292 GSM 1900 0.077 0.767 0.843 WCDMA Band II 0.150 0.585 0.585 WCDMA Band IV 0.112 0.987 0.987 WCDMA Band V 0.161 0.223 0.209 LTE FDD 2 0.128 1.074 1.074 LTE FDD 4 0.141 0.791 0.791 LTE FDD 5 0.178 0.139 0.140 LTE FDD 7 0.128 0.747 0.432 LTE TDD 38 0.046 0.228 0.314 Wi-Fi (2.4G) 0.478 0.219 0.219 BT 0.177 NA NA Date of Testing: August 3, 2019~ August 14, 2019 Table 2: Highest Simultaneous Transmission SAR Exposure Configuration 1g SAR Head 1g SAR Body-worn 1g SAR Hotspot Highest Simultaneous Transmission SAR (W/kg) 0.634 1.293 1.293 Note: 1. The detail for simultaneous transmission consideration is described in chapter 10.4. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 6 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 3 Description of Equipment under Test Report No.: R1907A0375-S1V1 Client Information Applicant Xiaomi Communications Co., Ltd. Applicant address The Rainbow City of China Resources,NO.68,Qinghe Middle Street,Haidian District,Beijing,China Manufacturer Xiaomi Communications Co., Ltd. Manufacturer address The Rainbow City of China Resources,NO.68,Qinghe Middle Street,Haidian District,Beijing,China General Technologies Application Purpose: Original Grant EUT Stage: Identical Prototype Model: IMEI: Hardware Version: M1908C3IH IMEI 1:866648040029992 IMEI 2:866648040030008 P2 Software Version: MIUI 10 Antenna Type: PIFA Antenna Device Class: B Wi-Fi Hotspot: Power Class: Power Level: Adapter Battery USB Cable 1 USB Cable 2 Wi-Fi 2.4G GSM 850:4 GSM 1900:1 UMTS Band II/IV/V:3 LTE FDD 2/4/5/7:3 LTE TDD 38:3 GSM 850:level 5 GSM 1900:level 0 UMTS Band II/IV/V:all up bits LTE FDD 2/4/5/7:max power LTE TDD 38:max power EUT Accessory Manufacturer: Jiangsu Chenyang Electron Co., Ltd. Model: MDY-09-EQ Manufacturer: Sunwoda Electronic Co.,LTD Model: BN51 Manufacturer: LUXSHARE Precision Industry Co., Ltd. Model: L23312 Manufacturer: SU ZHOU KELI SCIENCE&TECHNOLOGY DEVELOPMENT CO.,LTD Model: K23312 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 7 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Wireless Technology and Frequency Range Wireless Technology 850 GSM 1900 Modulation Voice(GMSK) GPRS(GMSK) EGPRS(GMSK,8PSK) Operating mode Multi-slot Class:8-1UP Multi-slot Class:10-2UP Multi-slot Class:12-4UP Multi-slot Class:33-4UP Does this device support DTM (Dual Transfer Mode)? Yes No UMTS Band II Band IV Band V QPSK, 16QAM HSDPA UE Category:24 HSUPA UE Category:6 DC-HSDPA UE Category:24 FDD 2 FDD 4 FDD 5 QPSK, 16QAM Rel.8 /Category 4 LTE FDD 7 TDD 38 Does this device support Carrier Aggregation (CA) Yes No Does this device support SV-LTE (1xRTT-LTE)? Yes No BT 2.4G Version 4.2LE Wi-Fi 2.4G DSSS,OFDM 802.11b/g/n HT20 Does this device support MIMO Yes No Tx (MHz) 824 ~ 849 1850 ~ 1910 1850 ~ 1910 1710 ~ 1755 824 ~ 849 1850 ~ 1910 1710 ~ 1755 824 ~ 849 2500 ~ 2570 2570 ~ 2620 2402 ~2480 2412 ~ 2462 Item Configure 1 Configure 2 Software The same The same Hardware The same The same Flash 3+32 4+64 Color Red Red Other The same The same Note: Customer declaration, two configures is the same, except for flash. There are more than one Configure, each one should be applied throughout the compliance test respectively, however, only the worst case (Configure 1) will be recorded in this report. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 8 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 4 Test Specification, Methods and Procedures Report No.: R1907A0375-S1V1 The tests documented in this report were performed in accordance with FCC 47 CFR § 2.1093, IEEE 1528- 2013, ANSI C95.1: 1992/IEEE C95.1: 1991, the following FCC Published RF exposure KDB procedures: 248227 D01 802.11Wi-Fi SAR v02r02 447498 D01 General RF Exposure Guidance v06 648474 D04 Handset SAR v01r03 690783 D01 SAR Listings on Grants v01r03 865664 D01 SAR measurement 100 MHz to 6 GHz v01r04 865664 D02 RF Exposure Reporting v01r02 941225 D01 3G SAR Procedures v03r01 941225 D05 SAR for LTE Devices v02r05 941225 D06 Hotspot Mode v02r01 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 9 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 5 Operational Conditions during Test Report No.: R1907A0375-S1V1 5.1 Test Positions 5.1.1 Against Phantom Head Measurements were made in "cheek" and "tilt" positions on both the left hand and right hand sides of the phantom. The positions used in the measurements were according to IEEE 1528 - 2013 "IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate(SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques". 5.1.2 Body Worn Configuration Body-worn operating configurations should be tested with the belt-clips and holsters attached to the device and positioned against a flat phantom in normal use configurations. Per FCC KDB Publication 648474 D04, Body-worn accessory exposure is typically related to voice mode operations when handsets are carried in body-worn accessories. The body-worn accessory procedures in FCC KDB Publication 447498 D01 should be used to test for body-worn accessory SAR compliance, without a headset connected to it. This enables the test results for such configuration to be compatible with that required for hotspot mode when the body-worn accessory test separation distance is greater than or equal to that required for hotspot mode, when applicable. When the reported SAR for a body-worn accessory, measured without a headset connected to the handset, is > 1.2 W/kg, the highest reported SAR configuration for that wireless mode and frequency band should be repeated for that body-worn accessory with a headset attached to the handset. Accessories for Body-worn operation configurations are divided into two categories: those that do not contain metallic components and those that do contain metallic components. When multiple accessories that do not contain metallic components are supplied with the device, the device is tested with only the accessory that dictates the closest spacing to the body. Then multiple accessories that contain metallic components are tested with the device with each accessory. If multiple accessories share an identical metallic component (i.e. the same metallic belt-clip used with different holsters with no other metallic components) only the accessory that dictates the closest spacing to the body is tested. Body-worn accessories may not always be supplied or available as options for some devices intended to be authorized for body-worn use. In this case, a test configuration with a separation distance between the back of the device and the flat phantom is used. Test position spacing was documented. Transmitters that are designed to operate in front of a person's face, as in push-to-talk configurations, are tested for SAR compliance with the front of the device positioned to face the flat phantom in head fluid. For devices that are carried next to the body such as a shoulder, waist or chest-worn transmitters, SAR compliance is tested with the accessories, including headsets and microphones, attached to the device and positioned against a flat phantom in a normal use configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 10 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 5.1.3 Phablet SAR test considerations Report No.: R1907A0375-S1V1 For smart phones, with a display diagonal dimension > 15.0 cm or an overall diagonal dimension > 16.0 cm, that can provide similar mobile web access and multimedia support found in mini-tablets or UMPC mini-tablets and support voice calls next to the ear, unless it is confirmed otherwise through KDB inquiries, the following phablet procedures should be applied to evaluate SAR compliance for each applicable wireless modes and frequency band. Devices marketed as phablets, regardless of form factors and operating characteristics must be tested as a phablet to determine SAR compliance. a) The normally required head and body-worn accessory SAR test procedures for handsets, including hotspot mode, must be applied. b) The UMPC mini-tablet procedures must also be applied to test the SAR of all surfaces and edges with an antenna located at 25 mm from that surface or edge, in direct contact with a flat phantom, for product specific 10-g SAR according to the body-equivalent tissue dielectric parameters in KDB Publication 865664 D01 to address interactive hand use exposure conditions. The 1-g SAR at 5 mm for UMPC mini-tablets is not required. When hotspot mode applies, product specific 10-g SAR is required only for the surfaces and edges with hotspot mode 1-g reported SAR > 1.2 W/kg; however, when power reduction applies to hotspot mode the measured SAR must be scaled to the maximum output power, including tolerance, allowed for phablet modes to compare with the 1.2 W/kg SAR test reduction threshold. The normal tablet procedures in KDB Publication 616217 are required when the overall diagonal dimension of the device is > 20.0 cm. Hotspot mode SAR is not required when normal tablet procedures are applied. Product specific 10-g SAR is also not required for the front (top) surface of larger form factor full size tablets. The more conservative normal tablet SAR results can be used to support phablet mode product specific 10-g SAR. c) The simultaneous transmission operating configurations applicable to voice and data transmissions for both phone and mini-tablet modes must be taken into consideration separately for 1-g and 10-g SAR to determine the simultaneous transmission SAR test exclusion and measurement requirements for the relevant wireless modes and exposure conditions. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 11 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 5.2 Measurement Variability Report No.: R1907A0375-S1V1 Per FCC KDB Publication 865664 D01, SAR measurement variability was assessed for each frequency band, which was determined by the SAR probe calibration point and tissue-equivalent medium used for the device measurements. When both head and body tissue-equivalent media were required for SAR measurements in a frequency band, the variability measurement procedures were applied to the tissue medium with the highest measured SAR, using the highest measured SAR configuration for that tissue-equivalent medium. These additional measurements were repeated after the completion of all measurements requiring the same head or body tissue-equivalent medium in a frequency band. The test device was returned to ambient conditions (normal room temperature) with the battery fully charged before it was re-mounted on the device holder for the repeated measurement(s) to minimize any unexpected variations in the repeated results. SAR Measurement Variability was assessed using the following procedures for each frequency band: 1) When the original highest measured SAR is 0.80 W/kg, the measurement was repeated once. 2) A second repeated measurement was preformed only if the ratio of largest to smallest SAR for the original and first repeated measurements was > 1.20 or when the original or repeated measurement was 1.45 W/kg (~ 10% from the 1-g SAR limit). 3) A third repeated measurement was performed only if the original, first or second repeated measurement was 1.5 W/kg and the ratio of largest to smallest SAR for the original, first and second repeated measurements is > 1.20. 4) Repeated measurements are not required when the original highest measured SAR is < 0.80 W/kg The same procedures should be adapted for measurements according to extremity and occupational exposure limits by applying a factor of 2.5 for extremity exposure and a factor of 5 for occupational exposure to the corresponding SAR thresholds. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 12 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 5.3 Test Configuration Report No.: R1907A0375-S1V1 5.3.1 GSM Test Configuration According to specification 3GPP TS 51.010, the maximum power of the GSM can do the power reduction for the multi-slot. The allowed power reduction in the multi-slot configuration is as following: Output power of reductions: Table 3: The allowed power reduction in the multi-slot configuration Number of timeslots in uplink assignment Permissible nominal reduction of maximum output power,(dB) 1 0 2 0 to 3,0 3 1,8 to 4,8 4 3,0 to 6,0 SAR test reduction for GPRS and EDGE modes is determined by the source-based time-averaged output power specified for production units, including tune-up tolerance. The data mode with highest specified time-averaged output power should be tested for SAR compliance in the applicable exposure conditions. For modes with the same specified maximum output power and tolerance, the higher number time-slot configuration should be tested. GSM voice and GPRS data use GMSK, which is a constant amplitude modulation with minimal peak to average power difference within the time-slot burst. For EDGE, GMSK is used for MCS 1 MCS 4 and 8-PSK is used for MCS 5 MCS 9; where 8-PSK has an inherently higher peak-to-average power ratio. The GMSK and 8-PSK EDGE configurations are considered separately for SAR compliance. The GMSK EDGE configurations are grouped with GPRS and considered with respect to time-averaged maximum output power to determine compliance. The 3G SAR test reduction procedure is applied to 8-PSK EDGE with GMSK GPRS/EDGE as the primary mode. 5.3.2 UMTS Test Configuration 5.3.2.1 3G SAR Test Reduction Procedure The default test configuration is to measure SAR with an established radio link between the EUT and a communication test set using a 12.2 kbps RMC (reference measurement channel) configured in Test Loop Mode 1. SAR is selectively confirmed for other physical channel configurations modes according to output power, exposure conditions and device operating capabilities. Maximum output power is verified by applying the applicable versions of 3GPP TS 34.121. 5.3.2.2 Head SARSAR for next to the ear head exposure is measured using a 12.2 kbps RMC with TPC bits configured to all "1's". The 3G SAR test reduction procedure is applied to AMR configurations with 12.2 kbps RMC as the primary mode. Otherwise, SAR is measured for 12.2 kbps AMR in 3.4 kbps SRB (signaling radio bearer) using the highest SAR configuration in 12.2 kbps RMC for head exposure. 5.3.2.3 Body-worn accessory SAR SAR for body-worn accessory configurations is measured using a 12.2 kbps RMC with TPC bits TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 13 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 configured to all "1's". The 3G SAR test reduction procedure is applied to other spreading codes and multiple DPDCHn configurations supported by the EUT with 12.2 kbps RMC as the primary mode. Otherwise, SAR is measured using an applicable RMC configuration with the corresponding spreading code or DPDCHn, for the highest reported body-worn accessory exposure SAR configuration in 12.2 kbps RMC. When more than 2 DPDCHn are supported by the EUT, it may be necessary to configure additional DPDCHn using FTM (Factory Test Mode) or other chipset based test approaches with parameters similar to those used in 384 kbps and 768 kbps RMC 5.3.2.4 Release 5 HSDPA Test Configuration The 3G SAR test reduction procedure is applied to HSDPA body-worn accessory configurations with 12.2 kbps RMC as the primary mode. Otherwise, SAR is measured for HSDPA using the HSDPA body SAR procedures in the "Release 5 HSDPA Data Devices" section of this document, for the highest SAR body-worn accessory exposure configuration in 12.2 kbps RMC. EUT with both HSDPA and HSUPA are tested according to Release 6 HSPA test procedures. HSDPA should be configured according to the UE category of a test device.The number of HSDSCH/ HS-PDSCHs, HARQ processes, minimum inter-TTI interval, transport block sizes and RV coding sequence are defined by the H-set. To maintain a consistent test configuration and stable transmission conditions, QPSK is used in the H-set for SAR testing. HS-DPCCH should be configured with a CQI feedback cycle of 4 ms with a CQI repetition factor of 2 to maintain a constant rate of active CQI slots. DPCCH and DPDCH gain factors(c, d), and HS-DPCCH power offset parameters (ACK, NACK, CQI) should be set according to values indicated in the Table below. The CQI value is determined by the UE category, transport block size, number of HS-PDSCHs and modulation used in the H-set. Table 4: Subtests for UMTS Release 5 HSDPA Sub-set c d d (SF) c/d hs (note 1, note 2) CM(dB) (note 3) MPR(dB) 1 2/15 15/15 64 2/15 4/15 0.0 0.0 2 12/15 (note 4) 15/15 (note 4) 64 12/15 (note 4) 24/15 1.0 0.0 3 15/15 8/15 64 15/8 30/15 1.5 0.5 4 15/15 4/15 64 15/4 30/15 1.5 0.5 Note1: ACK, NACK and CQI= 8Ahs = hs/c=30/15hs=30/15*c Note2: CM=1 for c/d =12/15, hs/c=24/15. Note3: For subtest 2 the cd ratio of 12/15 for the TFC during the measurement period(TF1,TF0) is achieved by setting the signaled gain factors for the reference TFC (TFC1,TF1) to c=11/15 and d=15/15. 5.3.2.5 Release 6 HSUPA Test Configuration The 3G SAR test reduction procedure is applied to HSPA (HSUPA/HSDPA with RMC) body-worn accessory configurations with 12.2 kbps RMC as the primary mode. Otherwise, SAR is measured for HSPA using the HSPA body SAR procedures in the "Release 6 HSPA Data Devices" section of this document, for the highest body-worn accessory exposure SAR configuration in 12.2 kbps RMC. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 14 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 When VOIP is applicable for next to the ear head exposure in HSPA, the 3G SAR test reduction procedure is applied to HSPA with 12.2 kbps RMC as the primary mode; otherwise, the same HSPA configuration used for body-worn accessory measurements is tested for next to the ear head exposure. Due to inner loop power control requirements in HSPA, a communication test set is required for output power and SAR tests. The 12.2 kbps RMC, FRC H-set 1 and E-DCH configurations for HSPA are configured according to the values indicated in Table 2 and other applicable procedures described in the `WCDMA EUT and `Release 5 HSDPA Data Devices' sections of this document Table 5: Sub-Test 5 Setup for Release 6 HSUPA Subset 1 c 11/15(3) d 15/15(3) d (SF) 64 c/d 11/15(3) hs(1) 22/15 ec 209/225 ed 1039/225 ed (SF) 4 ed (codes) 1 CM (2) (dB) 1.0 MPR (dB) 0.0 AG(4) Index 20 E-TFCI 75 2 6/15 15/15 64 6/15 12/15 12/15 94/75 4 3 15/15 9/15 64 15/9 30/15 30/15 ed1:47/15 ed2:47/15 4 4 2/15 15/15 64 2/15 4/15 2/15 56/75 4 5 15/15(4) 15/15(4) 64 15/15(4) 30/15 24/15 134/15 4 1 3.0 2.0 12 67 2 2.0 1.0 15 92 1 3.0 2.0 17 71 1 1.0 0.0 21 81 Note 1: ACK, NACK and CQI = 8 Ahs = hs/c = 30/15 hs= 30/15 *c. Note 2: CM = 1 for c/d =12/15, hs/c =24/15. For all other combinations of DPDCH, DPCCH, HS- DPCCH, E-DPDCH and E-DPCCH the MPR is based on the relative CM difference. Note 3: For subtest 1 the c/d ratio of 11/15 for the TFC during the measurement period (TF1, TF0) is achieved by setting the signaled gain factors for the reference TFC (TF1, TF1) to c = 10/15 and d = 15/15. Note 4: For subtest 5 the c/d ratio of 15/15 for the TFC during the measurement period (TF1, TF0) is achieved by setting the signaled gain factors for the reference TFC (TF1, TF1) to c = 14/15 and d = 15/15. Note 5: Testing UE using E-DPDCH Physical Layer category 1 Sub-test 3 is not required according to TS 25.306 Figure 5.1g. Note 6: ed can not be set directly; it is set by Absolute Grant Value. Table 6: HSUPA UE category UE E-DCH Category Maximum E-DCH Codes Transmitted Number of HARQ Processes E- DCH TTI (ms) Minimum Spreading Factor Maximum E-DCH Transport Block Bits Max Rate (Mbps) 1 1 4 10 4 7110 0.7296 2 8 2 4 2798 2 2 4 10 4 14484 1.4592 3 2 4 10 4 14484 1.4592 2 8 2 2 5772 2.9185 4 2 4 10 2 20000 2.00 5 2 4 10 2 20000 2.00 6 4 8 2 2 SF2 & 2 SF4 11484 5.76 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 15 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report (No DPDCH) 4 4 10 Report No.: R1907A0375-S1V1 20000 2.00 7 4 (No DPDCH) 4 8 2 2 SF2 & 2 SF4 22996 ? 4 10 20000 ? NOTE: When 4 codes are transmitted in parallel, two codes shall be transmitted with SF2 and two with SF4. UE Categories 1 to 6 supports QPSK only. UE Category 7 supports QPSK and 16QAM. (TS25.306-7.3.0) 5.3.2.6 HSPA and DC-HSDPA Test Configuration SAR test exclusion may apply to 3GPP Rel. 6 HSPA and Rel. 8 DC-HSDPA. When SAR measurement is required for HSPA or DC-HSDPA, a KDB inquiry is required to confirm that the wireless mode configurations in the test setup have remained stable throughout the SAR measurements. Without prior KDB confirmation to determine the SAR results are acceptable, a PAG is required for equipment approval. SAR test exclusion for HSPA and DC-HSDPA is determined according to the following: 1) The HSPA procedures are applied to configure 3GPP Rel. 6 HSPA devices in the required sub-test mode(s) to determine SAR test exclusion. 2) SAR is required for Rel. 8 DC-HSDPA when SAR is required for Rel. 5 HSDPA; otherwise, the 3G SAR test reduction procedure is applied to DC-HSDPA with 12.2 kbps RMC as the primary mode. Power is measured for DC-HSDPA according to the H-Set 12, FRC configuration in Table C.8.1.12 of 3GPP TS 34.121-1 to determine SAR test reduction. A primary and a secondary serving HS-DSCH Cell are required to perform the power measurement and for the results to be acceptable. 3) Regardless of whether a PBA is required, the following information must be verified and included in the SAR report for devices supporting HSPA or DC-HSDPA: a) The output power measurement results and applicable release version(s) of 3GPP TS 34.121. i) Power measurement difficulties due to test equipment setup or availability must be resolved between the grantee and its test lab. b) The power measurement results are in agreement with the individual device implementation and specifications. When Enhanced MPR (E-MPR) applies, the normal MPR targets may be modified according to the Cubic Metric (CM) measured by the device, which must be taken into consideration. c) The UE category, operating parameters, such as the and values used to configure the device for testing, power setback procedures described in 3GGPP TS 34.121 for the power measurements, and HSPA channel conditions (active and stable) for the entire duration of the measurement according to the required E-TFCI and AG index values. 4) When SAR measurement is required, the test configurations, procedures and power measurement results must be clearly described to confirm that the required test parameters are used, including E-TFCI and AG index stability and output power conditions. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 16 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 7: HS-DSCH UE category Report No.: R1907A0375-S1V1 5.3.3 LTE Test Configuration LTE modes were tested according to FCC KDB 941225 D05 publication. Please see notes after the tabulated SAR data for required test configurations. Establishing connections with base station simulators ensure a consistent means for testing SAR and are recommended for evaluating SAR [4]. The R&S CMW500 was used for LTE output power measurements and SAR testing. Max power control was used so the UE transmits with maximum output power during SAR testing. SAR must be measured with the maximum TTI (transmit time interval) supported by the device in each LTE configuration. A) Spectrum Plots for RB Configurations A properly configured base station simulator was used for SAR tests and power measurements. Therefore, spectrum plots for RB configurations were not required to be included in this report. B) MPR MPR is permanently implemented for this device by the manufacturer. The specific manufacturer TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 17 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 target MPR is indicated alongside the SAR results. MPR is enabled for this device, according to 3GPP TS36.101 Section 6.2.3 6.2.5 under Table 6.2.3-1. C)A-MPR A-MPR (Additional MPR) has been disabled for all SAR tests by setting NS=01 on the base station simulator. D) Largest channel bandwidth standalone SAR test requirements 1) QPSK with 1 RB allocation Start with the largest channel bandwidth and measure SAR for QPSK with 1 RB allocation, using the RB offset and required test channel combination with the highest maximum output power for RB offsets at the upper edge, middle and lower edge of each required test channel. When the reported SAR is 0.8 W/kg, testing of the remaining RB offset configurations and required test channels is not required for 1 RB allocation; otherwise, SAR is required for the remaining required test channels and only for the RB offset configuration with the highest output power for that channel. When the reported SAR of a required test channel is > 1.45 W/kg, SAR is required for all three RB offset configurations for that required test channel. 2) QPSK with 50% RB allocation The procedures required for 1 RB allocation in 1) are applied to measure the SAR for QPSK with 50% RB allocation. 3) QPSK with 100% RB allocation For QPSK with 100% RB allocation, SAR is not required when the highest maximum output power for 100 % RB allocation is less than the highest maximum output power in 50% and 1 RB allocations and the highest reported SAR for 1 RB and 50% RB allocation in 1) and 2) are 0.8 W/kg. Otherwise, SAR is measured for the highest output power channel and if the reported SAR is > 1.45 W/kg, the remaining required test channels must also be tested. 4) Higher order modulations For each modulation besides QPSK; e.g., 16-QAM, 64-QAM, apply the QPSK procedures in above sections to determine the QAM configurations that may need SAR measurement. For each configuration identified as required for testing, SAR is required only when the highest maximum output power for the configuration in the higher order modulation is > ½ dB higher than the same configuration in QPSK or when the reported SAR for the QPSK configuration is > 1.45 W/kg. E) Other channel bandwidth standalone SAR test requirements For the other channel bandwidths used by the device in a frequency band, apply all the procedures required for the largest channel bandwidth in section A) to determine the channels and RB configurations that need SAR testing and only measure SAR when the highest maximum output power of a configuration requiring testing in the smaller channel bandwidth is > ½ dB higher than the equivalent channel configurations in the largest channel bandwidth configuration or the reported SAR of a configuration for the largest channel bandwidth is > 1.45 W/kg. 5.3.4 Additional requirements for TDD LTE specification For Time-Division Duplex (TDD) systems, SAR must be tested using a fixed periodic duty factor according to the highest transmission duty factor implemented for the device and supported by the defined 3GPP LTE TDD configurations. TDD LTE Band supports 3GPP TS 36.211 section 4.2 for Type 2 Frame Structure and Table: Uplink-downlink configurations for uplink-downlink configurations and Table: Configuration of special subframe (lengths of DwPTS/GP/UpPTS) for Special subframe configurations. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 18 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report One radio frame , Tf = 307200 Ts = 10 ms One half -frame, 153600 Ts = 5 ms Figure 1: Frame structure type 2 Report No.: R1907A0375-S1V1 One slot, Tslot=15360 Ts 30720 Ts Subframe #0 One subframe , 30720 Ts DwPTS GP Subframe #2 UpPT S Subframe #3 Subframe #4 Subframe #5 DwPTS GP Subframe #7 UpPT S Subframe #8 Subframe #9 Table 8: Configuration of special subframe (lengths of DwPTS/GP/UpPTS) Normal cyclic prefix in downlink Extended cyclic prefix in downlink Special DwPTS UpPTS DwPTS UpPTS subframe configuration Normal Extended cyclic prefix cyclic prefix Normal Extended cyclic prefix cyclic prefix in in uplink in uplink in uplink uplink 0 6592 Ts 7680 Ts 1 2 19760 Ts 21952 Ts 2192 Ts 2560 Ts 20480 Ts 23040 Ts 2192 Ts 2560 Ts 3 24144 Ts 25600 Ts 4 26336 Ts 7680 Ts 5 6592 Ts 6 19760 Ts 20480 Ts 23040 Ts 4384 Ts 5120 Ts 7 21952 Ts 4384 Ts 5120 Ts 12800 Ts 8 24144 Ts - - - 9 13168 Ts - - - Table 9: Uplink-downlink configurations Uplink-downlink Downlink-to-Uplink Subframe number configuration Switch-point periodicity 0123456789 0 5 ms DSUUUDSUUU 1 5 ms DSUUDDSUUD 2 5 ms DSUDDDSUDD 3 10 ms DSUUUDDDDD 4 10 ms DSUUDDDDDD 5 10 ms DSUDDDDDDD 6 5 ms DSUUUDSUUD According to Figure 1, one radio frame is configured by 10 subframes, which consist of Uplink-subframe, Downlink-subframe and Special subframe. For TDD-LTE, the Duty Cycle should be calculated on Uplink-subframes and Special subframes, due to Special subframe containing both Uplink transmissions. So for one radio frame, Duty Cycle can be calculated with formula as below. The count of Uplink subframes are according to Table: Uplink-downlink configurations: Duty cycle =(30720Ts*Ups+Uplink Component*Specials)/(307200Ts) About the uplink component of Special subframes, we can figure out by Table: Configuration of TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 19 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 special subframe (lengths of DwPTS/GP/UpPTS): Uplink Component=UpPTS In conclusion, for the TDD LTE Band, Duty Cycle can be calculated with formula as below .all these sets are ok when we test, or we can set as below. Duty cycle =[(30720Ts*Ups)+ UpPTS *Specials]/(307200Ts) And we can get different Duty cycles under different configurations: SAR test Plan: For TDD LTE, SAR should be tested with the highest transmission duty factor (63.33%) using Uplink-downlink configuration 0 and Special subframe configuration 7 for Frame structure type TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 20 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 5.3.5 Wi-Fi Test Configuration SAR test reduction for 802.11 Wi-Fi transmission mode configurations are considered separately for DSSS and OFDM. An initial test position is determined to reduce the number of tests required for certain exposure configurations with multiple test positions. An initial test configuration is determined for each frequency band and aggregated band according to maximum output power, channel bandwidth, wireless mode configurations and other operating parameters to streamline the measurement requirements. For 2.4 GHz DSSS, either the initial test position or DSSS procedure is applied to reduce the number of SAR tests; these are mutually exclusive. For OFDM, an initial test position is only applicable to next to the ear, UMPC mini-tablet and hotspot mode configurations, which is tested using the initial test configuration to facilitate test reduction. For other exposure conditions with a fixed test position, SAR test reduction is determined using only the initial test configuration. The multiple test positions require SAR measurements in head, hotspot mode or UMPC mini-tablet configurations may be reduced according to the highest reported SAR determined using the initial test position(s) by applying the DSSS or OFDM SAR measurement procedures in the required wireless mode test configuration(s). The initial test position(s) is measured using the highest measured maximum output power channel in the required wireless mode test configuration(s). When the reported SAR for the initial test position is: 0.4 W/kg, further SAR measurement is not required for the other test positions in that exposure configuration and wireless mode combination within the frequency band or aggregated band. DSSS and OFDM configurations are considered separately according to the required SAR procedures. 0.4 W/kg, SAR is repeated using the same wireless mode test configuration tested in the initial test position to measure the subsequent next closet/smallest test separation distance and maximum coupling test position, on the highest maximum output power channel, until the reported SAR is 0.8 W/kg or all required test positions are tested. For subsequent test positions with equivalent test separation distance or when exposure is dominated by coupling conditions, the position for maximum coupling condition should be tested. When it is unclear, all equivalent conditions must be tested. For all positions/configurations tested using the initial test position and subsequent test positions, when the reported SAR is > 0.8 W/kg, measure the SAR for these positions/configurations on the subsequent next highest measured output power channel(s) until the reported SAR is 1.2 W/kg or all required test channels are considered. The additional power measurements required for this step should be limited to those necessary for identifying subsequent highest output power channels to apply the test reduction. To determine the initial test position, Area Scans were performed to determine the position with the Maximum Value of SAR (measured). The position that produced the highest Maximum Value of SAR is considered the worst case position; thus used as the initial test position. A Wi-Fi device must be configured to transmit continuously at the required data rate, channel bandwidth and signal modulation, using the highest transmission duty factor supported by the test mode tools for SAR measurement. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 21 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 5.3.6 BT Test Configuration For BT SAR testing, BT engineering testing software installed on the EUT can provide continuous transmitting RF signal with maximum output power. And the CBT control the EUT operating with hoping off and data rate set for 3DH5. The SAR measurement takes full account of the BT duty cycle and is reflected in the report, and the duty factor of the device is as follow: Note: Duty factor= Ton (ms)/ T(on+off) (ms)=2.883/3.750=77% TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 22 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 6 SAR Measurements System Configuration Report No.: R1907A0375-S1V1 6.1 SAR Measurement Set-up The DASY system for performing compliance tests consists of the following items: A standard high precision 6-axis robot with controller, teach pendant and software. An arm extension for accommodating the data acquisition electronics (DAE). An isotropic Field probe optimized and calibrated for the targeted measurement. A data acquisition electronics (DAE) which performs the signal amplification, signal multiplexing, AD-conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC. The Electro-optical converter (EOC) performs the conversion from optical to electrical signals for the digital communication to the DAE. To use optical surface detection, a special version of the EOC is required. The EOC signal is transmitted to the measurement server. The function of the measurement server is to perform the time critical tasks such as signal filtering, control of the robot operation and fast movement interrupts. The Light Beam used is for probe alignment. This improves the (absolute) accuracy of the probe positioning. A computer running WinXP or Win7 and the DASY software. Remote control and teach pendant as well as additional circuitry for robot safety such as warning lamps, etc. The phantom, the device holder and other accessories according to the targeted measurement. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 23 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 6.2 DASY5 E-field Probe System Report No.: R1907A0375-S1V1 The SAR measurements were conducted with the dosimetric probe EX3DV4(manufactured by SPEAG), designed in the classical triangular configuration and optimized for dosimetric evaluation. EX3DV4 Probe Specification Construction Calibration Frequency Directivity Dynamic Range Dimensions Application Symmetrical design with triangular core Built-in shielding against static charges PEEK enclosure material (resistant to organic solvents, e.g., DGBE) ISO/IEC 17025 calibration service available 10 MHz to > 6 GHz Linearity: ± 0.2 dB (30 MHz to 6 GHz) ± 0.3 dB in HSL (rotation around probe axis) ± 0.5 dB in tissue material (rotation normal to probe axis) 10 µW/g to > 100 mW/g Linearity: ± 0.2dB (noise: typically < 1 µW/g) Overall length: 330 mm (Tip: 20 mm) Tip diameter: 2.5 mm (Body: 12 mm) Typical distance from probe tip to dipole centers: 1 mm High precision dosimetric measurements in any exposure Scenario (e.g., very strong gradient fields). Only probe which enables compliance testing for frequencies up to 6 GHz with precision of better 30%. E-field Probe Calibration Each probe is calibrated according to a dosimetric assessment procedure with accuracy better than ± 10%. The spherical isotropy was evaluated and found to be better than ± 0.25dB. The sensitivity parameters (NormX, NormY, NormZ), the diode compression parameter (DCP) and the conversion factor (ConvF) of the probe are tested. The free space E-field from amplified probe outputs is determined in a test chamber. This is performed in a TEM cell for frequencies bellow 1 GHz, and in a wave guide above 1 GHz for free space. For the free space calibration, the probe is placed in the volumetric center of the cavity and at the proper orientation with the field. The probe is then rotated 360 degrees. E-field temperature correlation calibration is performed in a flat phantom filled with the appropriate simulated brain tissue. The measured free space E-field in the medium correlates to temperature rise in a dielectric medium. For temperature correlation calibration a RF transparent thermistor-based temperature probe is used in conjunction with the E-field probe. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 24 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report SAR=CT/t Where: t = Exposure time (30 seconds), C = Heat capacity of tissue (brain or muscle), T = Temperature increase due to RF exposure. Or SAR=IEI2/ Where: = Simulated tissue conductivity, = Tissue density (kg/m3). Report No.: R1907A0375-S1V1 6.3 SAR Measurement Procedure Power Reference Measurement The Power Reference Measurement and Power Drift Measurements are for monitoring the power drift of the device under test in the batch process. The minimum distance of probe sensors to surface determines the closest measurement point to phantom surface. This distance cannot be smaller than the distance of sensor calibration points to probe tip as defined in the probe properties. Area Scan The area scan is used as a fast scan in two dimensions to find the area of high field values, before doing a fine measurement around the hot spot. The sophisticated interpolation routines implemented in DASY software can find the maximum found in the scanned area, within a range of the global maximum. The range (in dB) is specified in the standards for compliance testing. For example, a 2 dB range is required in IEEE standard 1528 and IEC 62209 standards, whereby 3 dB is a requirement when compliance is assessed in accordance with the ARIB standard (Japan), if only one zoom scan follows the area scan, then only the absolute maximum will be taken as reference. For cases where multiple maximums are detected, the number of zoom scans has to be increased accordingly. Area scan parameters extracted from FCC KDB 865664 D01 SAR measurement 100 MHz to 6 GHz. 3 GHz > 3 GHz Maximum distance from closest measurement point (geometric center of probe sensors) to phantom surface Maximum probe angle from probe axis to phantom surface normal at the measurement location Maximum area scan spatial resolution: xArea, yArea 5 ± 1 mm ½··ln(2) ± 0.5 mm 30° ± 1° 20° ± 1° 2 GHz: 15 mm 3 4 GHz: 12 mm 2 3 GHz: 12 mm 4 6 GHz: 10 mm When the x or y dimension of the test device, in the measurement plane orientation, is smaller than the above, the measurement resolution must be the corresponding x or y dimension of the test device with at least one measurement point on the test device. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 25 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Zoom Scan Report No.: R1907A0375-S1V1 Zoom scans are used assess the peak spatial SAR values within a cubic averaging volume containing 1 gram and 10 gram of simulated tissue. The zoom scan measures points (refer to table below) within a cube shoes base faces are centered on the maxima found in a preceding area scan job within the same procedure. When the measurement is done, the zoom scan evaluates the averaged SAR for 1 gram and 10 gram and displays these values next to the job's label. Zoom scan parameters extracted from FCC KDB 865664 D01 SAR measurement 100 MHz to 6 GHz. 3GHz > 3 GHz Maximum zoom scan spatial resolution:xzoomyzoom 2GHz: 8mm 2 3GHz: 5mm* 3 4GHz: 5mm* 4 6GHz: 4mm* Maximum zoom scan spatial resolution, normal to phantom surface Uniform grid: zzoom(n) Graded grid zzoom(1): between 1st two points closest to phantom surface zzoom(n1): between subsequent points 5mm 4mm 3 4GHz: 4mm 4 5GHz: 3mm 5 6GHz: 2mm 3 4GHz: 3mm 4 5GHz: 2.5mm 5 6GHz: 2mm 1.5·zzoom(n-1) Minimum 3 4GHz: 28mm zoom scan X, y, z 30mm 4 5GHz: 25mm volume 5 6GHz: 22mm Note: is the penetration depth of a plane-wave at normal incidence to the tissue medium; see draft standard IEEE P1528-2011 for details. * When zoom scan is required and the reported SAR from the area scan based 1-g SAR estimation procedures of KDB 447498 is 1.4W/kg, 8mm, 7mm and 5mm zoom scan resolution may be applied, respectively, for 2GHz to 3GHz, 3GHz to 4GHz and 4GHz to 6GHz. Volume Scan Procedures The volume scan is used for assess overlapping SAR distributions for antennas transmitting in different frequency bands. It is equivalent to an oversized zoom scan used in standalone measurements. The measurement volume will be used to enclose all the simultaneous transmitting antennas. For antennas transmitting simultaneously in different frequency bands, the volume scan is measured separately in each frequency band. In order to sum correctly to compute the 1g aggregate SAR, the EUT remain in the same test position for all measurements and all volume scan use the same spatial resolution and grid spacing. When all volume scan were completed, the software, SEMCAD postprocessor can combine and subsequently superpose these measurement data to calculating the multiband SAR. Power Drift Monitoring All SAR testing is under the EUT install full charged battery and transmit maximum output power. In DASY measurement software, the power reference measurement and power drift measurement procedures are used for monitoring the power drift of EUT during SAR test. Both these procedures measure the field at a specified reference position before and after the SAR testing. The software will calculate the field difference in dB. If the power drifts more than 5%, the SAR will be retested. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 26 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 7 Main Test Equipment Report No.: R1907A0375-S1V1 Name of Equipment Network analyzer Manufacturer Type/Model Serial Number Agilent E5071B MY42404014 Last Cal. 2019-05-19 Cal. Due Date 2020-05-18 Dielectric Probe Kit HP 85070E US44020115 2019-05-19 2020-05-18 Power meter Agilent E4417A GB41291714 2019-05-19 2020-05-18 Power sensor Agilent N8481H MY50350004 2019-05-19 2020-05-18 Power sensor Agilent E9327A US40441622 2019-05-19 2020-05-18 Dual directional coupler Agilent 778D-012 50519 2019-05-19 2020-05-18 Dual directional coupler Agilent 777D 50146 2019-05-19 2020-05-18 Amplifier Wideband radio communication tester E-field Probe INDEXSAR R&S SPEAG IXA-020 CMW 500 EX3DV4 0401 113645 3677 2019-05-19 2020-05-18 2019-05-19 2020-05-18 2019-06-19 2020-06-18 DAE SPEAG DAE4 1291 2018-12-04 2019-12-03 Validation Kit 1750MHz SPEAG D1750V2 1033 2017-01-10 2020-01-09 Validation Kit 1900MHz SPEAG D1900V2 5d060 2017-08-26 2020-08-25 Temperature Probe Tianjin jinming JM222 AA1009129 2019-05-19 2020-05-18 Hygrothermograph Anymetr NT-311 20150731 2019-05-19 2020-05-18 Software for Test Speag DASY5 52.8.8.1222 / / Softwarefor Tissue Agilent 85070 E06.01.36 / / TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 27 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Equipment Manufacturer Model SN Cal. Data Cal. interval System Validation Dipole SPEAG D835V2 4d005 May. 18, 2018 3 Year System Validation Dipole SPEAG D1750V2 1086 May. 18, 2018 3 Year System Validation Dipole SPEAG D1800V2 2d140 May. 18, 2018 3 Year System Validation Dipole SPEAG D1900V2 509 May. 18, 2018 3 Year System Validation Dipole SPEAG D2450V2 1014 Jun. 07, 2018 3 Year System Validation Dipole SPEAG D2600V2 1153 Jun. 07, 2018 3 Year Dosimetric E-Field Probe SPEAG ES3DV3 3090 Apr. 12, 2019 1 Year Data Acquisition Electronics SPEAG DAE4 662 Apr. 11, 2019 1 Year Radio Communication Analyzer Anritsu MT8820C 6200918396 Dec. 12, 2018 1 Year ENA Series Network Analyzer Agilent 8753ES US39170317 Dec. 12, 2018 1 Year Dielectric Assessment Kit SPEAG DAK-3.5 1056 N/A N/A USB/GPIB Interface Agilent 82357B N10149 N/A N/A Signal Generator R&S SMT06 100796 May. 14, 2019 1 Year Signal Generator R&S SMB100A 103718 Dec. 12, 2018 1 Year POWER METER R&S NRP 101293 Dec. 18, 2018 1 Year Shanghai Gao Thermometer Zhi Precision Instrument HB6801 120100323 May. 16, 2019 1 Year Co., Ltd. Coupler REBES TC-05180-10S 161221001 N/A N/A Amplifier Mini-Circuit ZHL42 QA1252001 N/A N/A DC Source Agilent 66319B MY43000795 N/A N/A TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 28 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 8 Tissue Dielectric Parameter Measurements & System Verification 8.1 Tissue Verification The temperature of the tissue-equivalent medium used during measurement must also be within 18C to 25C and within ± 2C of the temperature when the tissue parameters are characterized. The dielectric parameters must be measured before the tissue-equivalent medium is used in a series of SAR measurements. The parameters should be re-measured after each 3 4 days of use; or earlier if the dielectric parameters can become out of tolerance. Target values Frequency (MHz) Water (%) Salt Sugar Glycol Preventol Cellulose (%) (%) (%) (%) (%) r (s/m) 835 41.45 1.45 56 0 0.1 1.0 41.5 0.90 1750 55.24 0.31 0 44.45 0 0 40.1 1.37 Head 1900 55.242 0.306 0 44.452 0 0 40.0 1.40 2450 62.7 0.5 0 36.8 0 0 39.2 1.80 2600 55.242 0.306 0 44.452 0 0 39.0 1.96 835 52.5 1.4 45 0 0.1 1.0 55.2 0.97 1750 69.91 0.12 0 29.97 0 0 53.4 1.49 Body 1900 69.91 0.13 0 29.96 0 0 53.3 1.52 2450 73.2 0.1 0 26.7 0 0 52.7 1.95 2600 72.6 0.1 0 27.3 0 0 52.5 2.16 Measurements results Frequency (MHz) Head 835 Body Test Date Temp Aug. 04, 2019 21.5 Aug. 03, 2019 21.5 Measured Dielectric Parameters (s/m) r 0.931 0.977 43.000 55.600 Target Dielectric Parameters (s/m) r 0.90 41.50 0.97 55.20 Limit (Within ±5%) Dev Dev (%) r (%) 3.44 3.61 0.72 0.72 1750 Head Aug. 14, 2019 21.5 Body Aug. 10, 2019 21.5 1.340 1.470 40.20 53.800 1.37 40.10 -2.19 0.25 1.49 53.40 -1.34 0.75 1900 Head Aug. 14, 2019 21.5 Body Aug. 13, 2019 21.5 1.410 1.560 40.10 54.800 1.40 40.00 0.71 0.25 1.52 53.30 2.63 2.81 2450 Head Aug. 05, 2019 21.6 Body Aug. 05, 2019 21.5 1.780 2.010 40.200 52.900 1.80 39.20 -1.11 2.55 1.95 52.70 3.08 0.38 2600 Head Aug. 12, 2019 21.8 Body Aug. 12, 2019 21.5 2.050 2.080 38.300 52.700 1.96 39.00 4.59 -1.79 2.16 52.50 -3.70 0.38 Note: The depth of tissue-equivalent liquid in a phantom must be 15.0 cm for SAR measurements 3 GHz and 10.0 cm for measurements > 3 GHz. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 29 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 8.2 System Performance Check Report No.: R1907A0375-S1V1 The manufacturer calibrates the probes annually. Dielectric parameters of the tissue simulates were measured using the dielectric probe kit and the network analyzer. A system check measurement for every day was made following the determination of the dielectric parameters of the Tissue simulates, using the dipole validation kit. The dipole antenna was placed under the flat section of the twin SAM phantom. System check is performed regularly on all frequency bands where tests are performed with the DASY system. Picture 1System Performance Check setup Picture 2 Setup Photo TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 30 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Justification for Extended SAR Dipole Calibrations Usage of SAR dipoles calibrated less than 3 years ago but more than 1 year ago were confirmed in maintaining return loss (< - 20 dB, within 20% of prior calibration) and impedance (within 5 ohm from prior calibration) requirements per extended calibrations in KDB 865664 D01: Dipole Date of Measurement Return Loss(dB) % Impedance () Dipole D1750V2 SN: 1033 Head Liquid 1/10/2017 1/9/2018 1/8/2019 -40.3 / 49.8 / -40.0 0.74 49.9 0.1 -40.2 -0.50 49.6 0.3 Dipole D1900V2 SN: 5d060 Head Liquid 8/26/2017 8/25/2018 -23.4 / 52.0 / -24.7 -5.56 54.4 2.4 System Check results Frequency (MHz) Test Date Temp 250mW/ 10mW Measured SAR1g (W/kg) 1W Normalized SAR1g (W/kg) 1W Target SAR1g (W/kg) % (Limit ±10%) Head Aug. 04, 2019 21.5 0.09 9.00 9.45 -4.76 835 Body Aug. 03, 2019 21.5 0.09 9.00 9.74 -7.60 Head Aug. 14, 2019 21.5 8.95 1750 Body Aug. 10, 2019 21.5 0.38 35.80 38.00 37.20 37.60 -3.76 1.06 Head Aug. 14, 2019 21.5 9.88 1900 Body Aug. 13, 2019 21.5 0.42 39.52 42.00 40.10 39.50 -1.45 6.33 Head Aug. 05, 2019 21.6 0.49 2450 Body Aug. 05, 2019 21.5 0.50 49.00 50.00 51.40 50.50 -4.67 -0.99 Head Aug. 12, 2019 21.8 0.52 2600 Body Aug. 12, 2019 21.5 0.55 52.00 55.00 56.00 54.80 -7.14 0.36 NoteTarget Values used derive from the calibration certificate Data Storage and Evaluation. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 31 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 9 Normal and Maximum Output Power Report No.: R1907A0375-S1V1 KDB 447498 D01 at the maximum rated output power and within the tune-up tolerance range specified for the product, but not more than 2 dB lower than the maximum tune-up tolerance limit. 9.1 GSM Mode Burst-Averaged output power(dBm) Frame-Averaged output power(dBm) GSM 850 Full Power Tune-up Channel/Frenqucy(MHz) Division Tune-up MAX 128 190 251 Factors /824.2 /836.6 /848.8 MAX Channel/Frenqucy(MHz) 128 190 251 /824.2 /836.6 /848.8 GSM CS 33.50 33.13 32.91 32.89 9.03 24.50 24.10 23.88 23.86 1 Tx Slot 33.50 33.06 32.87 32.88 9.03 GPRS/ 2 Tx Slots 31.00 30.20 30.21 30.23 6.02 EGPRS (GMSK) 3 Tx Slots 29.50 28.45 28.46 28.49 4.26 4 Tx Slots 28.50 27.37 27.24 27.36 3.01 24.50 25.00 25.20 25.50 24.03 24.18 24.19 24.36 23.84 24.19 24.20 24.23 23.85 24.21 24.23 24.35 1 Tx Slot 27.50 26.67 26.52 26.56 9.03 18.50 17.64 17.49 17.53 EGPRS 2 Tx Slots 25.00 23.89 23.73 23.86 6.02 (8PSK) 3 Tx Slots 23.50 22.18 22.03 21.87 4.26 19.00 19.20 17.87 17.92 17.71 17.77 17.84 17.61 4 Tx Slots 22.50 20.97 20.88 20.95 3.01 19.50 17.96 17.87 17.94 Burst-Averaged output power(dBm) Frame-Averaged output power(dBm) GSM 1900 Full Power Tune-up Channel/Frenqucy(MHz) Division Tune-up Channel/Frenqucy(MHz) MAX 512 661 810 Factors /1850.2 /1880 /1909.8 MAX 512 661 810 /1850.2 /1880 /1909.8 GSM CS 30.50 29.97 30.08 29.87 9.03 21.50 20.94 21.05 20.84 1 Tx Slot 30.50 29.93 30.06 29.88 9.03 GPRS/ 2 Tx Slots 28.00 27.35 27.27 27.28 6.02 EGPRS (GMSK) 3 Tx Slots 26.50 25.62 25.78 25.66 4.26 4 Tx Slots 25.50 24.61 24.52 24.59 3.01 21.50 22.00 22.20 22.50 20.90 21.33 21.36 21.60 21.03 21.25 21.52 21.51 20.85 21.26 21.40 21.58 1 Tx Slot 26.50 25.47 25.54 25.56 9.03 17.50 16.44 16.51 16.53 EGPRS 2 Tx Slots 24.00 22.85 22.76 22.95 6.02 (8PSK) 3 Tx Slots 22.50 21.11 21.04 20.99 4.26 18.00 18.20 16.83 16.85 16.74 16.78 16.93 16.73 4 Tx Slots 21.50 20.02 20.05 19.92 3.01 18.50 17.01 17.04 16.91 Notes:The worst-case configuration and mode for SAR testing is determined to be as follows: 1. Standalone: GSM 850 GMSK (GPRS) mode with 4 time slots for Max power, GSM 1900 GMSK (GPRS) mode with 4 time slots for Max power,based on the output power measurements above. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 32 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Burst-Averaged output power(dBm) Frame-Averaged output power(dBm) GSM 1900 Reduced Power Tune-up Channel/Frenqucy(MHz) Division Tune-up Channel/Frenqucy(MHz) MAX 512 661 810 Factors /1850.2 /1880 /1909.8 MAX 512 661 810 /1850.2 /1880 /1909.8 GSM CS 25.50 25.16 25.01 24.90 9.03 16.50 16.16 16.01 15.90 1 Tx Slot 25.50 25.09 24.98 24.87 9.03 GPRS/ 2 Tx Slots 24.00 23.42 23.23 23.27 6.02 EGPRS (GMSK) 3 Tx Slots 21.50 20.78 20.52 20.52 4.26 4 Tx Slots 21.50 20.66 20.41 20.45 3.01 16.50 18.00 17.20 18.50 16.09 17.42 16.52 17.66 15.98 17.23 16.26 17.41 15.87 17.27 16.26 17.45 1 Tx Slot 26.50 25.36 25.47 25.38 9.03 17.50 16.36 16.47 16.38 EGPRS 2 Tx Slots 24.00 22.51 22.45 22.12 6.02 (8PSK) 3 Tx Slots 22.50 21.05 21.07 21.11 4.26 18.00 18.20 16.51 16.79 16.45 16.81 16.12 16.85 4 Tx Slots 21.50 19.82 19.96 19.61 3.01 18.50 16.82 16.96 16.61 Notes:The worst-case configuration and mode for SAR testing is determined to be as follows: 1. Standalone: GSM 1900 GMSK (GPRS) mode with 4 time slots for Max power,based on the output power measurements above. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 33 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 9.2 WCDMA Mode Report No.: R1907A0375-S1V1 The following tests were completed according to the test requirements outlined in the 3GPP TS34.121 specification. WCDMA Full Power Band II(dBm) Band IV(dBm) Band V(dBm) Tx Channel 9262 9400 9538 Tune-up 1312 1413 1513 Tune-up 4132 4183 4233 Tune-up Frequency(MHz) 1852.4 1880 1907.6 Limit 1712.4 1732.6 1752.6 Limit 826.4 836.6 846.6 Limit RMC 12.2kbps 23.05 23.18 23.32 24.50 23.31 23.26 23.43 24.50 23.03 22.99 23.04 24.50 Sub 1 22.24 22.14 22.23 23.50 22.38 22.10 22.28 23.50 22.02 21.91 22.01 23.50 Sub 2 22.31 22.33 22.38 23.50 22.44 22.28 22.46 23.50 22.13 21.97 22.04 23.50 HSDPA Sub 3 21.64 21.69 21.84 23.00 21.74 21.71 21.97 23.00 21.47 21.47 21.55 23.00 Sub 4 21.65 21.69 21.86 23.00 21.91 21.83 21.73 23.00 21.58 21.56 21.66 23.00 Sub 1 22.11 22.08 22.25 23.50 21.94 21.67 22.32 23.50 21.46 21.79 21.85 23.50 Sub 2 21.14 21.12 20.82 21.50 20.80 20.66 21.38 21.50 20.79 20.97 20.94 21.50 HSUPA Sub 3 21.12 21.02 20.73 22.50 20.69 21.03 21.34 22.50 20.76 20.30 20.32 22.50 Sub 4 21.61 21.62 21.71 21.50 21.41 21.21 21.30 21.50 21.15 21.31 21.29 21.50 Sub 5 21.74 21.75 21.95 23.50 21.85 21.74 21.97 23.50 21.20 21.24 21.18 23.50 Note: 1.Per KDB 941225 D01, SAR for each exposure is measured using a 12.2 kbps RMC with TPC bits configured to all "1's". WCDMA Reduced Power Band II(dBm) Band IV(dBm) Tx Channel 9262 9400 9538 Tune-up 1312 1413 1513 Tune-up Frequency(MHz) 1852.4 1880 1907.6 Limit 1712.4 1732.6 1752.6 Limit RMC 12.2kbps 16.38 16.36 16.42 17.50 17.33 17.14 17.16 18.50 Sub 1 15.25 15.37 15.34 16.50 16.19 16.17 16.30 17.50 HSDPA Sub 2 Sub 3 15.34 14.90 15.36 14.91 15.32 16.50 16.28 16.21 16.32 17.50 14.92 16.00 15.73 15.76 15.77 17.00 Sub 4 14.87 14.88 14.85 16.00 15.75 15.73 15.74 17.00 Sub 1 14.54 14.55 14.57 16.50 15.50 15.54 15.52 17.50 Sub 2 14.46 14.47 14.49 14.50 15.13 15.16 15.11 15.50 HSUPA Sub 3 14.36 14.38 14.31 15.50 14.49 14.45 14.43 16.50 Sub 4 14.98 14.96 14.93 14.50 15.62 15.59 15.53 15.50 Sub 5 14.93 14.91 14.96 16.50 15.82 15.83 15.84 17.50 Note: 1.Per KDB 941225 D01, SAR for each exposure is measured using a 12.2 kbps RMC with TPC bits configured to all "1's". TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 34 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 9.3 LTE Mode Report No.: R1907A0375-S1V1 UE Power Class: 3 (23 +/- 2dBm). The allowed Maximum Power Reduction (MPR) for the maximum output power due to higher order modulation and transmit bandwidth configuration (resource blocks) is specified in Table 6.2.3-1 of the 3GPP TS36.101. Bandwidth 1.4MHz Bandwidth 3MHz LTE FDD Band 2 Full Power Modulation RB size 1 1 1 QPSK 3 3 3 6 1 1 1 16QAM 3 3 3 6 Modulation RB size 1 1 1 QPSK 8 8 8 15 16QAM 1 RB offset 0 2 5 0 1 3 0 0 2 5 0 1 3 0 RB offset 0 7 14 0 3 7 0 0 Conducted Power(dBm) Channel/Frequency (MHz) 18607/1850.7 18900/1880 19193/1909.3 23.19 23.21 22.92 23.37 23.39 23.28 22.89 23.17 22.82 23.30 23.14 23.21 23.24 23.13 23.19 23.22 23.31 23.36 22.21 22.25 22.21 22.14 22.13 21.68 22.24 22.04 22.21 22.10 21.75 21.98 22.28 22.13 22.25 22.27 22.10 22.18 22.19 22.20 22.35 21.24 21.06 21.32 Channel/Frequency (MHz) 18615/1851.5 18900/1880 19185/1908.5 23.17 23.19 22.99 23.45 23.32 23.20 22.92 23.06 22.89 22.29 22.14 22.17 22.29 22.16 22.20 22.21 22.31 22.45 22.28 22.33 22.22 22.19 22.13 21.80 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 22.0 22.0 22.0 22.0 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 35 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 1 1 8 8 8 15 Bandwidth Modulation RB size 1 1 1 QPSK 12 12 12 5MHz 25 1 1 1 16QAM 12 12 12 25 Bandwidth Modulation RB size 1 1 1 QPSK 25 25 25 10MHz 50 1 1 1 16QAM 25 25 25 50 Bandwidth Modulation RB size 1 15MHz QPSK 1 1 7 14 0 3 7 0 RB offset 0 12 24 0 6 13 0 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 0 0 24 49 0 12 25 0 RB offset 0 37 74 Report No.: R1907A0375-S1V1 22.13 21.94 22.12 23.0 21.96 21.92 21.97 23.0 21.15 20.98 21.36 22.0 21.30 21.03 21.32 22.0 21.28 21.20 21.33 22.0 21.17 21.11 21.26 22.0 Channel/Frequency (MHz) Tune-up 18625/1852.5 18900/1880 19175/1907.5 Limit 23.23 23.22 23.01 24.0 23.30 23.38 23.21 24.0 22.99 23.14 22.94 24.0 22.24 22.23 22.13 23.0 22.16 22.14 22.34 23.0 22.33 22.33 22.44 23.0 22.29 22.28 22.35 23.0 22.28 22.06 21.63 23.0 22.29 22.11 22.14 23.0 22.00 21.86 21.89 23.0 21.16 21.10 21.32 22.0 21.17 21.18 21.34 22.0 21.15 21.28 21.46 22.0 21.15 21.23 21.35 22.0 Channel/Frequency (MHz) Tune-up 18650/1855 18900/1880 19150/1905 Limit 23.29 23.10 22.99 24.0 23.41 23.49 23.29 24.0 22.91 23.18 22.89 24.0 22.28 22.24 22.29 23.0 22.29 22.13 22.26 23.0 22.19 22.17 22.31 23.0 22.28 22.26 22.34 23.0 22.29 22.10 21.80 23.0 22.20 21.92 22.09 23.0 22.10 21.86 21.87 23.0 21.16 20.97 21.35 22.0 21.16 21.02 21.29 22.0 21.20 21.22 21.30 22.0 21.21 21.09 21.23 22.0 Channel/Frequency (MHz) Tune-up 18675/1857.5 18900/1880 19125/1902.5 Limit 23.31 23.08 23.01 24.0 23.27 23.45 23.12 24.0 22.98 23.09 22.91 24.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 36 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 36 0 36 19 36 39 75 0 1 0 1 37 1 74 16QAM 36 0 36 19 36 39 75 0 Bandwidth Modulation RB size RB offset 1 0 1 50 1 99 QPSK 50 0 50 25 50 50 20MHz 100 0 1 0 1 50 1 99 16QAM 50 0 50 25 50 50 100 0 Report No.: R1907A0375-S1V1 22.30 22.21 22.18 23.0 22.28 22.14 22.32 23.0 22.29 22.29 22.41 23.0 22.25 22.24 22.23 23.0 22.24 22.08 21.72 23.0 22.28 22.11 22.15 23.0 22.07 21.81 22.00 23.0 21.11 21.10 21.33 22.0 21.29 21.13 21.28 22.0 21.26 21.24 21.45 22.0 21.10 21.16 21.22 22.0 Channel/Frequency (MHz) Tune-up 18700/1860 18900/1880 19100/1900 Limit 23.34 23.22 23.06 24.0 23.47 23.50 23.31 24.0 23.05 23.24 22.98 24.0 22.34 22.29 22.31 23.0 22.34 22.30 22.38 23.0 22.36 22.34 22.46 23.0 22.35 22.35 22.39 23.0 22.31 22.17 21.82 23.0 22.29 22.12 22.27 23.0 22.15 21.95 22.06 23.0 21.29 21.15 21.41 22.0 21.31 21.22 21.35 22.0 21.30 21.31 21.47 22.0 21.26 21.24 21.36 22.0 Bandwidth 1.4MHz LTE FDD Band 2 Reduced Power Modulation RB size 1 1 1 QPSK 3 3 3 6 1 16QAM 1 1 3 RB offset 0 2 5 0 1 3 0 0 2 5 0 Conducted Power(dBm) Channel/Frequency (MHz) 18607/1850.7 18900/1880 19193/1909.3 17.18 16.91 16.56 17.33 17.13 16.81 17.01 17.03 16.57 18.18 18.00 18.11 18.11 18.04 18.00 18.16 18.15 17.97 17.05 17.03 16.94 16.99 16.92 17.03 17.20 17.50 16.80 16.82 16.88 16.67 18.05 18.04 17.94 Tune-up Limit 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 37 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 3 3 6 Bandwidth Modulation RB size 1 1 1 QPSK 8 8 8 3MHz 15 1 1 1 16QAM 8 8 8 15 Bandwidth Modulation RB size 1 1 1 QPSK 12 12 12 5MHz 25 1 1 1 16QAM 12 12 12 25 Bandwidth Modulation RB size 1 1 10MHz QPSK 1 25 25 25 1 3 0 RB offset 0 7 14 0 3 7 0 0 7 14 0 3 7 0 RB offset 0 12 24 0 6 13 0 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 Report No.: R1907A0375-S1V1 18.16 17.92 17.98 18.0 18.11 17.89 17.84 18.0 17.13 16.86 17.15 18.0 Channel/Frequency (MHz) Tune-up 18615/1851.5 18900/1880 19185/1908.5 Limit 17.16 16.89 16.63 18.0 17.41 17.06 16.73 18.0 17.04 16.92 16.64 18.0 17.17 17.00 17.07 18.0 17.16 17.07 17.01 18.0 17.15 17.15 17.06 18.0 17.12 17.11 16.95 18.0 17.04 16.92 17.15 18.0 17.09 17.40 16.71 18.0 16.68 17.05 16.66 18.0 16.92 16.89 17.05 18.0 17.19 16.85 17.12 18.0 17.20 16.89 16.82 18.0 17.06 16.91 17.09 18.0 Channel/Frequency (MHz) Tune-up 18625/1852.5 18900/1880 19175/1907.5 Limit 17.22 16.92 16.65 18.0 17.26 17.12 16.74 18.0 17.11 17.00 16.69 18.0 17.12 17.09 17.03 18.0 17.03 17.05 17.15 18.0 17.27 17.17 17.05 18.0 17.13 17.06 17.08 18.0 17.13 16.85 16.98 18.0 17.25 17.57 16.73 18.0 16.72 16.99 16.58 18.0 16.93 17.01 17.01 18.0 17.06 17.00 17.14 18.0 17.07 16.97 16.95 18.0 17.04 17.03 17.18 18.0 Channel/Frequency (MHz) Tune-up 18650/1855 18900/1880 19150/1905 Limit 17.28 16.80 16.63 18.0 17.37 17.23 16.82 18.0 17.03 17.04 16.64 18.0 17.16 17.10 17.19 18.0 17.16 17.04 17.07 18.0 17.13 17.01 16.92 18.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 38 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 50 1 1 1 16QAM 25 25 25 50 Bandwidth Modulation RB size 1 1 1 QPSK 36 36 36 75 15MHz 1 1 1 16QAM 36 36 36 75 Bandwidth Modulation RB size 1 1 1 QPSK 50 50 50 20MHz 100 1 1 1 16QAM 50 50 50 100 0 0 24 49 0 12 25 0 RB offset 0 37 74 0 19 39 0 0 37 74 0 19 39 0 RB offset 0 50 99 0 25 50 0 0 50 99 0 25 50 0 Report No.: R1907A0375-S1V1 17.12 17.04 17.07 18.0 17.14 16.89 17.15 18.0 17.16 17.38 16.68 18.0 16.82 16.99 16.56 18.0 16.93 16.88 17.04 18.0 17.05 16.84 17.09 18.0 17.12 16.91 16.79 18.0 17.10 16.89 17.06 18.0 Channel/Frequency (MHz) Tune-up 18675/1857.5 18900/1880 19125/1902.5 Limit 17.30 16.78 16.65 18.0 17.23 17.19 16.65 18.0 17.10 16.95 16.66 18.0 17.18 17.07 17.08 18.0 17.15 17.05 17.13 18.0 17.23 17.13 17.02 18.0 17.09 17.02 16.96 18.0 17.09 16.87 17.07 18.0 17.24 17.57 16.74 18.0 16.79 16.94 16.69 18.0 16.88 17.01 17.02 18.0 17.18 16.95 17.08 18.0 17.18 16.93 16.94 18.0 16.99 16.96 17.05 18.0 Channel/Frequency (MHz) Tune-up 18700/1860 18900/1880 19100/1900 Limit 17.33 16.92 16.70 18.0 17.43 17.24 16.84 18.0 17.17 17.10 16.73 18.0 17.22 17.15 17.21 18.0 17.21 17.21 17.19 18.0 17.30 17.18 17.07 18.0 17.19 17.13 17.12 18.0 17.16 16.96 17.17 18.0 17.25 17.58 16.86 18.0 16.87 17.08 16.75 18.0 17.06 17.06 17.10 18.0 17.20 17.04 17.15 18.0 17.22 17.00 16.96 18.0 17.15 17.04 17.19 18.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 39 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report LTE FDD Band 4 Full Power Bandwidth Modulation RB size 1 1 1 QPSK 3 3 3 6 1.4MHz 1 1 1 16QAM 3 3 3 6 Bandwidth Modulation RB size 1 1 1 QPSK 8 8 8 3MHz 15 1 1 1 16QAM 8 8 8 15 Bandwidth Modulation RB size 1 1 1 5MHz QPSK 12 12 12 25 RB offset 0 2 5 0 1 3 0 0 2 5 0 1 3 0 RB offset 0 7 14 0 3 7 0 0 7 14 0 3 7 0 RB offset 0 12 24 0 6 13 0 Report No.: R1907A0375-S1V1 Conducted Power(dBm) Channel/Frequency (MHz) 19957/1710.7 20175/1732.5 20393/1754.3 22.47 22.12 22.39 22.74 22.57 22.96 22.69 22.60 22.66 22.55 22.50 22.77 22.67 22.62 22.77 22.72 22.58 22.93 21.49 21.59 21.80 21.40 21.17 21.58 21.64 21.29 21.68 21.29 21.08 21.57 21.57 21.41 21.65 21.66 21.67 21.75 21.59 21.73 21.73 20.48 20.60 20.78 Channel/Frequency (MHz) 19965/1711.5 20175/1732.5 20385/1753.5 22.43 22.21 22.52 22.86 22.51 22.97 22.68 22.51 22.55 21.63 21.52 21.71 21.60 21.64 21.91 21.62 21.60 21.88 21.58 21.53 21.78 21.47 21.26 21.60 21.76 21.16 21.75 21.25 21.09 21.56 20.51 20.41 20.65 20.67 20.64 20.86 20.57 20.72 20.84 20.64 20.63 20.81 Channel/Frequency (MHz) 19975/1712.5 20175/1732.5 20375/1752.5 22.47 22.09 22.44 22.84 22.51 22.94 22.73 22.67 22.65 21.74 21.47 21.70 21.55 21.58 21.88 21.63 21.76 21.84 21.54 21.53 21.85 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 22.0 22.0 22.0 22.0 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 22.0 22.0 22.0 22.0 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 40 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 1 1 1 16QAM 12 12 12 25 Bandwidth Modulation RB size 1 1 1 QPSK 25 25 25 10MHz 50 1 1 1 16QAM 25 25 25 50 Bandwidth Modulation RB size 1 1 1 QPSK 36 36 36 75 15MHz 1 1 1 16QAM 36 36 36 75 Bandwidth Modulation RB size 20MHz QPSK 1 1 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 0 0 24 49 0 12 25 0 RB offset 0 37 74 0 19 39 0 0 37 74 0 19 39 0 RB offset 0 50 Report No.: R1907A0375-S1V1 21.51 21.26 21.57 23.0 21.60 21.34 21.69 23.0 21.32 21.11 21.57 23.0 20.53 20.48 20.80 22.0 20.56 20.70 20.78 22.0 20.57 20.77 20.87 22.0 20.64 20.57 20.84 22.0 Channel/Frequency (MHz) Tune-up 20000/1715 20175/1732.5 20350/1750 Limit 22.47 22.09 22.41 24.0 22.75 22.55 22.96 24.0 22.73 22.50 22.57 24.0 21.61 21.49 21.84 23.0 21.55 21.53 21.89 23.0 21.73 21.62 21.82 23.0 21.49 21.45 21.81 23.0 21.49 21.21 21.64 23.0 21.63 21.19 21.81 23.0 21.19 21.01 21.51 23.0 20.57 20.46 20.79 22.0 20.51 20.66 20.86 22.0 20.57 20.77 20.82 22.0 20.61 20.59 20.81 22.0 Channel/Frequency (MHz) Tune-up 20025/1717.5 20175/1732.5 20325/1747.5 Limit 22.51 22.20 22.38 24.0 22.69 22.62 23.03 24.0 22.55 22.62 22.70 24.0 21.56 21.43 21.81 23.0 21.66 21.64 21.90 23.0 21.60 21.67 21.91 23.0 21.51 21.51 21.82 23.0 21.39 21.23 21.60 23.0 21.78 21.19 21.74 23.0 21.28 21.00 21.66 23.0 20.65 20.41 20.67 22.0 20.56 20.63 20.86 22.0 20.46 20.79 20.74 22.0 20.46 20.68 20.68 22.0 Channel/Frequency (MHz) Tune-up 20050/1720 20175/1732.5 20300/1745 Limit 22.55 22.25 22.55 24.0 22.86 22.67 23.07 24.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 41 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 1 99 50 0 50 25 50 50 100 0 1 0 1 50 1 99 16QAM 50 0 50 25 50 50 100 0 22.75 21.74 21.73 21.74 21.60 21.56 21.78 21.36 20.66 20.71 20.65 20.65 22.69 21.61 21.65 21.77 21.64 21.27 21.34 21.14 20.54 20.81 20.85 20.69 Report No.: R1907A0375-S1V1 22.72 24.0 21.84 23.0 21.91 23.0 21.94 23.0 21.87 23.0 21.70 23.0 21.86 23.0 21.69 23.0 20.83 22.0 20.91 22.0 20.88 22.0 20.84 22.0 Bandwidth 1.4MHz Bandwidth 3MHz LTE FDD Band 4 Reduced Power Modulation RB size 1 1 1 QPSK 3 3 3 6 1 1 1 16QAM 3 3 3 6 Modulation RB size 1 1 1 QPSK 8 8 8 15 1 16QAM 1 1 RB offset 0 2 5 0 1 3 0 0 2 5 0 1 3 0 RB offset 0 7 14 0 3 7 0 0 7 14 Conducted Power(dBm) Channel/Frequency (MHz) 19957/1710.7 20175/1732.5 20393/1754.3 16.24 16.31 16.30 16.31 16.85 16.92 16.24 16.85 16.65 17.56 17.56 17.73 17.69 17.66 17.79 17.53 17.59 17.96 16.62 16.68 16.72 16.21 16.46 16.59 16.22 16.59 16.44 16.12 16.60 16.58 17.74 17.36 17.52 17.79 17.37 17.69 17.43 17.35 17.66 16.49 16.47 16.66 Channel/Frequency (MHz) 19965/1711.5 20175/1732.5 20385/1753.5 16.20 16.40 16.43 16.43 16.79 16.93 16.23 16.76 16.54 16.64 16.58 16.67 16.62 16.68 16.93 16.43 16.61 16.91 16.71 16.62 16.70 16.28 16.55 16.61 16.34 16.46 16.51 16.08 16.61 16.57 Tune-up Limit 18.0 18.0 18.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 16.0 16.0 16.0 16.0 Tune-up Limit 18.0 18.0 18.0 17.0 17.0 17.0 17.0 17.0 17.0 17.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 42 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 8 8 8 15 Bandwidth Modulation RB size 1 1 1 QPSK 12 12 12 5MHz 25 1 1 1 16QAM 12 12 12 25 Bandwidth Modulation RB size 1 1 1 QPSK 25 25 25 50 10MHz 1 1 1 16QAM 25 25 25 50 Bandwidth Modulation RB size 1 1 15MHz QPSK 1 36 36 0 3 7 0 RB offset 0 12 24 0 6 13 0 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 0 0 24 49 0 12 25 0 RB offset 0 37 74 0 19 Report No.: R1907A0375-S1V1 16.68 16.36 16.52 16.0 16.80 16.34 16.80 16.0 16.41 16.34 16.77 16.0 16.65 16.50 16.69 16.0 Channel/Frequency (MHz) Tune-up 19975/1712.5 20175/1732.5 20375/1752.5 Limit 16.24 16.28 16.35 18.0 16.41 16.79 16.90 18.0 16.28 16.92 16.64 18.0 16.75 16.53 16.66 17.0 16.57 16.62 16.90 17.0 16.44 16.77 16.87 17.0 16.67 16.62 16.77 17.0 16.32 16.55 16.58 17.0 16.18 16.64 16.45 17.0 16.15 16.63 16.58 17.0 16.70 16.43 16.67 16.0 16.69 16.40 16.72 16.0 16.41 16.39 16.80 16.0 16.65 16.44 16.72 16.0 Channel/Frequency (MHz) Tune-up 20000/1715 20175/1732.5 20350/1750 Limit 16.24 16.28 16.32 18.0 16.32 16.83 16.92 18.0 16.28 16.75 16.56 18.0 16.62 16.55 16.80 17.0 16.57 16.57 16.91 17.0 16.54 16.63 16.85 17.0 16.62 16.54 16.73 17.0 16.30 16.50 16.65 17.0 16.21 16.49 16.57 17.0 16.02 16.53 16.52 17.0 16.74 16.41 16.66 16.0 16.64 16.36 16.80 16.0 16.41 16.39 16.75 16.0 16.62 16.46 16.69 16.0 Channel/Frequency (MHz) Tune-up 20025/1717.5 20175/1732.5 20325/1747.5 Limit 16.28 16.39 16.29 18.0 16.26 16.90 16.99 18.0 16.10 16.87 16.69 18.0 16.57 16.49 16.77 17.0 16.68 16.68 16.92 17.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 43 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 36 39 75 0 1 0 1 37 1 74 16QAM 36 0 36 19 36 39 75 0 Bandwidth Modulation RB size RB offset 1 0 1 50 1 99 QPSK 50 0 50 25 50 50 20MHz 100 0 1 0 1 50 1 99 16QAM 50 0 50 25 50 50 100 0 Report No.: R1907A0375-S1V1 16.41 16.68 16.94 17.0 16.64 16.60 16.74 17.0 16.20 16.52 16.61 17.0 16.36 16.49 16.50 17.0 16.11 16.52 16.67 17.0 16.82 16.36 16.54 16.0 16.69 16.33 16.80 16.0 16.30 16.41 16.67 16.0 16.47 16.55 16.56 16.0 Channel/Frequency (MHz) Tune-up 20050/1720 20175/1732.5 20300/1745 Limit 16.32 16.44 16.46 18.0 16.43 16.95 17.03 18.0 16.30 16.94 16.71 18.0 16.75 16.67 16.80 17.0 16.75 16.69 16.93 17.0 16.55 16.78 16.97 17.0 16.73 16.73 16.79 17.0 16.37 16.56 16.71 17.0 16.36 16.64 16.62 17.0 16.19 16.66 16.70 17.0 16.83 16.49 16.70 16.0 16.84 16.51 16.85 16.0 16.49 16.47 16.81 16.0 16.66 16.56 16.72 16.0 Bandwidth 1.4MHz LTE FDD Band 5 Full Power Modulation RB size 1 1 1 QPSK 3 3 3 6 1 1 16QAM 1 3 3 RB offset 0 2 5 0 1 3 0 0 2 5 0 1 Conducted Power(dBm) Channel/Frequency (MHz) 20407/824.7 20525/836.5 20643/848.3 22.56 22.81 22.53 22.72 22.72 23.06 22.57 22.52 22.76 22.97 22.75 23.10 23.00 22.77 22.94 22.87 22.85 23.00 21.89 21.71 21.99 22.36 22.09 21.93 22.22 22.21 22.00 22.14 22.21 21.64 22.07 21.83 22.06 22.05 21.92 22.06 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 22.0 22.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 44 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 3 6 Bandwidth Modulation RB size 1 1 1 QPSK 8 8 8 15 3MHz 1 1 1 16QAM 8 8 8 15 Bandwidth Modulation RB size 1 1 1 QPSK 12 12 12 5MHz 25 1 1 1 16QAM 12 12 12 25 Bandwidth Modulation RB size 1 1 1 10MHz QPSK 25 25 25 50 3 0 RB offset 0 7 14 0 3 7 0 0 7 14 0 3 7 0 RB offset 0 12 24 0 6 13 0 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 0 Report No.: R1907A0375-S1V1 22.12 21.98 21.82 22.0 21.13 20.83 21.04 22.0 Channel/Frequency (MHz) Tune-up 20415/825.5 20525/836.5 20635/847.5 Limit 22.57 22.84 22.58 24.0 22.71 22.86 23.11 24.0 22.74 22.61 22.62 24.0 21.99 21.91 22.09 23.0 21.94 21.78 21.97 23.0 21.94 21.89 22.08 23.0 21.93 21.78 21.99 23.0 22.27 22.01 21.90 23.0 22.33 22.13 21.92 23.0 22.11 22.19 21.81 23.0 21.04 20.84 21.11 22.0 21.06 20.88 21.09 22.0 21.12 20.97 20.91 22.0 21.09 20.78 21.03 22.0 Channel/Frequency (MHz) Tune-up 20425/826.5 20525/836.5 20625/846.5 Limit 22.63 22.80 22.61 24.0 22.70 22.90 23.19 24.0 22.56 22.65 22.71 24.0 21.87 21.80 22.09 23.0 21.90 21.72 21.92 23.0 21.93 21.85 22.04 23.0 22.00 21.82 21.95 23.0 22.27 22.15 21.85 23.0 22.15 22.07 21.99 23.0 22.21 22.18 21.77 23.0 21.03 20.85 21.05 22.0 20.97 20.81 21.01 22.0 21.12 20.99 20.93 22.0 21.05 20.84 20.91 22.0 Channel/Frequency (MHz) Tune-up 20450/829 20525/836.5 20600/844 Limit 22.67 22.94 22.69 24.0 22.89 22.91 23.22 24.0 22.76 22.67 22.78 24.0 22.01 21.91 22.10 23.0 22.03 21.92 22.09 23.0 22.04 21.94 22.08 23.0 22.03 21.90 22.05 23.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 45 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 1 0 1 24 1 49 16QAM 25 0 25 12 25 25 50 0 22.39 22.33 22.27 21.11 21.10 21.14 21.20 Report No.: R1907A0375-S1V1 22.18 22.03 23.0 22.22 22.04 23.0 22.24 21.84 23.0 20.92 21.20 22.0 20.95 21.14 22.0 21.05 21.01 22.0 20.91 21.06 22.0 Bandwidth 5MHz Bandwidth 10MHz LTE FDD Band 7 Full Power Modulation RB size 1 1 1 QPSK 12 12 12 25 1 1 1 16QAM 12 12 12 25 Modulation RB size 1 1 1 QPSK 25 25 25 50 1 1 1 16QAM 25 25 25 50 RB offset 0 12 24 0 6 13 0 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 0 0 24 49 0 12 25 0 Conducted Power(dBm) Channel/Frequency (MHz) 20775/2502.5 21100/2535 21425/2567.5 23.22 23.07 22.81 23.49 23.31 22.79 23.26 22.98 23.03 22.16 22.02 22.26 22.24 22.04 22.18 22.26 22.10 22.18 22.15 22.27 21.95 22.13 22.00 21.82 22.27 21.77 21.72 22.02 21.77 21.85 20.98 21.01 21.18 20.98 21.10 21.14 21.03 21.00 21.19 21.19 20.97 21.13 Channel/Frequency (MHz) 20800/2505 21100/2535 21400/2565 23.32 23.23 22.88 23.48 23.19 22.86 23.15 23.08 22.95 22.11 22.09 22.34 22.27 22.04 22.27 22.23 22.21 22.23 22.22 22.24 22.04 21.97 21.98 21.90 22.24 21.74 21.68 22.07 21.59 21.85 21.06 20.92 21.15 20.94 21.04 21.19 21.07 21.14 21.11 21.13 20.99 21.16 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 22.0 22.0 22.0 22.0 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 22.0 22.0 22.0 22.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 46 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Bandwidth Modulation RB size 1 1 1 QPSK 36 36 36 15MHz 75 1 1 1 16QAM 36 36 36 75 Bandwidth Modulation RB size 1 1 1 QPSK 50 50 50 20MHz 100 1 1 1 16QAM 50 50 50 100 RB offset 0 37 74 0 19 39 0 0 37 74 0 19 39 0 RB offset 0 50 99 0 25 50 0 0 50 99 0 25 50 0 Report No.: R1907A0375-S1V1 Channel/Frequency (MHz) Tune-up 20825/2507.5 21100/2535 21375/2562.5 Limit 23.31 23.12 22.76 24.0 23.35 23.36 22.84 24.0 23.27 23.11 23.06 24.0 22.22 22.09 22.19 23.0 22.29 22.12 22.24 23.0 22.21 22.16 22.30 23.0 22.21 22.20 22.05 23.0 22.04 22.13 21.82 23.0 22.26 21.63 21.82 23.0 21.99 21.66 21.80 23.0 21.04 21.03 21.23 22.0 20.99 21.02 21.13 22.0 21.16 21.01 21.14 22.0 21.24 21.04 21.21 22.0 Channel/Frequency (MHz) Tune-up 20850/2510 21100/2535 21350/2560 Limit 23.35 23.25 22.96 24.0 23.53 23.37 22.95 24.0 23.33 23.16 23.07 24.0 22.29 22.22 22.38 23.0 22.31 22.22 22.33 23.0 22.33 22.24 22.35 23.0 22.25 22.37 22.06 23.0 22.16 22.13 21.98 23.0 22.37 21.81 21.85 23.0 22.11 21.78 21.86 23.0 21.14 21.09 21.33 22.0 21.13 21.12 21.29 22.0 21.22 21.16 21.22 22.0 21.24 21.17 21.26 22.0 Bandwidth 5MHz LTE FDD Band 7 Reduced Power Modulation RB size 1 1 QPSK 1 12 12 12 RB offset 0 12 24 0 6 13 Conducted Power(dBm) Channel/Frequency (MHz) 20775/2502.5 21100/2535 21425/2567.5 17.26 16.63 16.98 17.57 16.88 16.96 17.15 16.80 17.07 17.23 16.97 17.11 17.34 17.02 17.09 17.30 17.02 17.01 Tune-up Limit 18.0 18.0 18.0 18.0 18.0 18.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 47 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 25 1 1 1 16QAM 12 12 12 25 Bandwidth Modulation RB size 1 1 1 QPSK 25 25 25 50 10MHz 1 1 1 16QAM 25 25 25 50 Bandwidth Modulation RB size 1 1 1 QPSK 36 36 36 15MHz 75 1 1 1 16QAM 36 36 36 75 Bandwidth Modulation RB size 20MHz QPSK 1 0 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 0 0 24 49 0 12 25 0 RB offset 0 37 74 0 19 39 0 0 37 74 0 19 39 0 RB offset 0 Report No.: R1907A0375-S1V1 17.21 17.14 17.04 18.0 17.11 17.30 17.42 18.0 17.28 16.92 17.51 18.0 17.14 16.85 17.74 18.0 17.18 17.19 16.89 18.0 17.15 17.30 16.78 18.0 17.04 17.10 17.15 18.0 17.21 17.08 16.88 18.0 Channel/Frequency (MHz) Tune-up 20800/2505 21100/2535 21400/2565 Limit 17.36 16.79 17.05 18.0 17.56 16.76 17.03 18.0 17.04 16.90 16.99 18.0 17.18 17.04 17.19 18.0 17.37 17.02 17.18 18.0 17.27 17.13 17.06 18.0 17.28 17.11 17.13 18.0 16.95 17.28 17.50 18.0 17.25 16.89 17.47 18.0 17.19 16.67 17.74 18.0 17.26 17.10 16.86 18.0 17.11 17.24 16.83 18.0 17.08 17.24 17.07 18.0 17.15 17.10 16.91 18.0 Channel/Frequency (MHz) Tune-up 20825/2507.5 21100/2535 21375/2562.5 Limit 17.35 16.68 16.93 18.0 17.43 16.93 17.01 18.0 17.16 16.93 17.10 18.0 17.29 17.04 17.04 18.0 17.39 17.10 17.15 18.0 17.25 17.08 17.13 18.0 17.27 17.07 17.14 18.0 17.02 17.43 17.42 18.0 17.27 16.78 17.61 18.0 17.11 16.74 17.69 18.0 17.24 17.21 16.94 18.0 17.16 17.22 16.77 18.0 17.17 17.11 17.10 18.0 17.26 17.15 16.96 18.0 Channel/Frequency (MHz) Tune-up 20850/2510 21100/2535 21350/2560 Limit 17.39 16.81 17.13 18.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 48 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 1 50 1 99 50 0 50 25 50 50 100 0 1 0 1 50 1 99 16QAM 50 0 50 25 50 50 100 0 17.61 17.22 17.36 17.41 17.37 17.31 17.14 17.38 17.23 17.34 17.30 17.23 17.26 16.94 16.98 17.17 17.20 17.16 17.24 17.43 16.96 16.86 17.27 17.32 17.26 17.28 Report No.: R1907A0375-S1V1 17.12 18.0 17.11 18.0 17.23 18.0 17.24 18.0 17.18 18.0 17.15 18.0 17.58 18.0 17.64 18.0 17.75 18.0 17.04 18.0 16.93 18.0 17.18 18.0 17.01 18.0 Bandwidth 5MHz Bandwidth 10MHz LTE TDD Band 38 Full Power Modulation RB size 1 1 1 QPSK 12 12 12 25 1 1 1 16QAM 12 12 12 25 Modulation RB size 1 1 1 QPSK 25 25 25 50 16QAM 1 1 RB offset 0 12 24 0 6 13 0 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 0 0 24 Conducted Power(dBm) Channel/Frequency (MHz) 37775/2572.5 38000/2595 38225/2617.5 22.19 22.21 22.65 22.28 22.44 22.94 22.07 22.15 22.59 21.41 21.33 21.34 21.55 21.37 21.52 21.48 21.47 21.62 21.44 21.37 21.39 21.79 21.21 22.17 22.08 21.50 22.25 21.66 21.18 22.16 20.50 20.42 20.42 20.56 20.60 20.58 20.48 20.62 20.65 20.53 20.39 20.49 Channel/Frequency (MHz) 37800/2575 38000/2595 38200/2615 22.18 22.08 22.71 22.32 22.44 23.04 22.16 22.12 22.58 21.40 21.48 21.30 21.51 21.25 21.49 21.37 21.42 21.64 21.38 21.53 21.48 21.75 21.19 22.20 22.10 21.46 22.30 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 23.0 23.0 22.0 22.0 22.0 22.0 Tune-up Limit 24.0 24.0 24.0 23.0 23.0 23.0 23.0 23.0 23.0 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 49 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 1 25 25 25 50 Bandwidth Modulation RB size 1 1 1 QPSK 36 36 36 75 15MHz 1 1 1 16QAM 36 36 36 75 Bandwidth Modulation RB size 1 1 1 QPSK 50 50 50 20MHz 100 1 1 1 16QAM 50 50 50 100 49 0 12 25 0 RB offset 0 37 74 0 19 39 0 0 37 74 0 19 39 0 RB offset 0 50 99 0 25 50 0 0 50 99 0 25 50 0 Report No.: R1907A0375-S1V1 21.66 21.11 22.21 23.0 20.50 20.48 20.41 22.0 20.55 20.45 20.63 22.0 20.51 20.59 20.55 22.0 20.44 20.52 20.38 22.0 Channel/Frequency (MHz) Tune-up 37825/2577.5 38000/2595 38175/2612.5 Limit 22.17 22.13 22.61 24.0 22.39 22.58 22.92 24.0 22.12 22.26 22.75 24.0 21.43 21.31 21.34 23.0 21.37 21.26 21.53 23.0 21.45 21.49 21.64 23.0 21.54 21.47 21.40 23.0 21.76 21.06 22.08 23.0 22.17 21.41 22.41 23.0 21.66 21.05 22.22 23.0 20.41 20.56 20.38 22.0 20.38 20.44 20.52 22.0 20.35 20.45 20.55 22.0 20.44 20.42 20.53 22.0 Channel/Frequency (MHz) Tune-up 37850/2580 38000/2595 38150/2610 Limit 22.29 22.26 22.76 24.0 22.46 22.59 23.05 24.0 22.25 22.30 22.76 24.0 21.53 21.49 21.47 23.0 21.56 21.45 21.61 23.0 21.57 21.52 21.71 23.0 21.55 21.53 21.51 23.0 21.94 21.22 22.25 23.0 22.26 21.54 22.43 23.0 21.83 21.22 22.23 23.0 20.59 20.61 20.52 22.0 20.56 20.62 20.65 22.0 20.54 20.65 20.73 22.0 20.58 20.55 20.54 22.0 Bandwidth 5MHz LTE TDD Band 38 Reduced Power Modulation RB size QPSK 1 RB offset 0 Conducted Power(dBm) Channel/Frequency (MHz) 37775/2572.5 38000/2595 38225/2617.5 21.12 21.02 20.75 Tune-up Limit 22.5 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 50 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 1 1 12 12 12 25 1 1 1 16QAM 12 12 12 25 Bandwidth Modulation RB size 1 1 1 QPSK 25 25 25 10MHz 50 1 1 1 16QAM 25 25 25 50 Bandwidth Modulation RB size 1 1 1 QPSK 36 36 15MHz 36 75 1 1 16QAM 1 36 36 12 24 0 6 13 0 0 12 24 0 6 13 0 RB offset 0 24 49 0 12 25 0 0 24 49 0 12 25 0 RB offset 0 37 74 0 19 39 0 0 37 74 0 19 Report No.: R1907A0375-S1V1 21.13 21.31 21.15 22.5 21.07 21.07 20.78 22.5 20.94 21.02 21.10 22.5 21.07 21.13 21.08 22.5 21.08 21.11 21.03 22.5 20.96 21.02 21.05 22.5 20.08 21.47 20.73 22.5 20.11 21.59 20.74 22.5 20.06 21.28 20.85 22.5 20.53 20.60 20.68 22.5 20.67 20.84 20.66 22.5 20.60 20.79 20.62 22.5 20.55 20.62 20.73 22.5 Channel/Frequency (MHz) Tune-up 37800/2575 38000/2595 38200/2615 Limit 21.11 20.89 20.81 22.5 21.17 21.31 21.25 22.5 21.16 21.04 20.77 22.5 20.93 21.17 21.06 22.5 21.03 21.01 21.05 22.5 20.97 21.06 21.05 22.5 20.90 21.18 21.14 22.5 20.04 21.45 20.76 22.5 20.13 21.55 20.79 22.5 20.06 21.21 20.90 22.5 20.53 20.66 20.67 22.5 20.66 20.69 20.71 22.5 20.63 20.76 20.52 22.5 20.46 20.75 20.62 22.5 Channel/Frequency (MHz) Tune-up 37825/2577.5 38000/2595 38175/2612.5 Limit 21.10 20.94 20.71 22.5 21.24 21.45 21.13 22.5 21.12 21.18 20.94 22.5 20.96 21.00 21.10 22.5 20.89 21.02 21.09 22.5 21.05 21.13 21.05 22.5 21.06 21.12 21.06 22.5 20.05 21.32 20.64 22.5 20.20 21.50 20.90 22.5 20.06 21.15 20.91 22.5 20.44 20.74 20.64 22.5 20.49 20.68 20.60 22.5 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 51 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 36 39 75 0 Bandwidth Modulation RB size RB offset 1 0 1 50 1 99 QPSK 50 0 50 25 50 50 20MHz 100 0 1 0 1 50 1 99 16QAM 50 0 50 25 50 50 100 0 Report No.: R1907A0375-S1V1 20.47 20.62 20.52 22.5 20.46 20.65 20.77 22.5 Channel/Frequency (MHz) Tune-up 37850/2580 38000/2595 38150/2610 Limit 21.22 21.07 20.86 22.5 21.31 21.46 21.26 22.5 21.25 21.22 20.95 22.5 21.06 21.18 21.23 22.5 21.08 21.21 21.17 22.5 21.17 21.16 21.12 22.5 21.07 21.18 21.17 22.5 20.23 21.48 20.81 22.5 20.29 21.63 20.92 22.5 20.23 21.32 20.92 22.5 20.62 20.79 20.78 22.5 20.67 20.86 20.73 22.5 20.66 20.82 20.70 22.5 20.60 20.78 20.78 22.5 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 52 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 9.4 WLAN Mode Report No.: R1907A0375-S1V1 Wi-Fi 2.4G Mode Channel /Frequency(MHz) 802.11b (1M) 1/2412 6/2437 11/2462 802.11g (6M) 1/2412 6/2437 11/2462 802.11n-HT20 (MCS0) 1/2412 6/2437 11/2462 Note: Initial test configuration is 802.11b mode. Tune-up 17.5 17.5 17.5 16 16 16 14 14 14 Maximum Output Power (dBm) Meas. TP Set Level 16.46 15 16.83 15 16.84 14 13.78 14 13.96 14 14.35 14 13.92 14 13.78 14 14.55 14 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 53 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 9.5 Bluetooth Mode Report No.: R1907A0375-S1V1 BT GFSK /4DQPSK 8DPSK BLE GFSK Conducted Power(dBm) Channel/Frequency(MHz) Ch 0/2402 MHz Ch 39/2441 MHz Ch 78/2480 MHz 8.49 8.91 7.93 7.08 7.58 6.6 7.12 7.6 6.59 Ch 0/2402 MHz Ch 19/2440 MHz Ch 39/2480 MHz 0.06 0.15 -0.12 Tune-up Limit (dBm) 12 12 12 Tune-up Limit (dBm) 2 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 54 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 10 Measured and Reported (Scaled) SAR Results Report No.: R1907A0375-S1V1 10.1 EUT Antenna Locations Overall (Length x Width): 156.338 mm x 75.408 mm Overall Diagonal: 165mm/Display Diagonal: 155mm Distance of the Antenna to the EUT surface/edge Antenna Back Side Front side Left Edge Right Edge Top Edge Bottom Edge Main-Antenna BT/Wi-Fi Antenna 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm 25mm Hotspot mode, Positions for SAR tests Mode Back Side Front side Left Edge Right Edge Top Edge Bottom Edge Main-Antenna Yes Yes Yes Yes N/A Yes BT/Wi-Fi Antenna Yes Yes N/A Yes Yes N/A Note: 1. Per KDB 941225 D06, when the overall device length and width are 9cm*5cm, the test distance is 10mm. SAR must be measured for all sides and surfaces with a transmitting antenna located within 25mm from that surface or edge. 2.For smart phones with an overall diagonal dimension is 165mm.Per KDB 648474 D04, for smart phones with a display diagonal dimension > 15.0 cm or an overall diagonal dimension> 16.0 cm, product specific 10-g SAR must be tested as a phablet to determine SAR compliance.For Phablet, Since hotspot mode 1-g reported SAR < 1.2 W/kg, product specific 10-g SAR is no required. 3. Per FCC KDB 447498 D01, TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 55 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 for each exposure position, testing of other requised channels within the operating mode of a frequency band is not required when the reported 1-g or 10-g SAR for the mid-band or highest output power channel is: a) 0.8 W/kg or 2.0 W/kg, for 1-g or 10-g respectively, when the transmission band is 100MHz b) 0.6 W/kg or 1.5 W/kg, for1-g or 10-g respectively, when the transmission band is between 100 MHz and 200 MHz. c) 0.4 W/kg or 1.0 Wkg, for 1-g or 10-g respectively, when the transmission band is 200 MHz. 3.When the original highest measured SAR is 0.80 W/kg, the measurement was repeated once. 4. Per FCC KDB Publication 648474 D04, SAR was evaluated without a headset connected to the device. Since the reported SAR was 1.2 W/kg, no additional SAR evaluations using a headset cable were required. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 56 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 10.2 Standalone SAR test exclusion considerations Per KDB 447498 D01, the 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[f(GHz)] 3.0 for 1-g SAR and 7.5 for product specific 10-g SAR f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison Per KDB 447498 D01, when the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. Bluetooth Head Body-worn Hotspot SAR Distance (mm) 5 10 10 MAXPower (dBm) 12 12 12 Frequency (MHz) 2480 2480 2480 Ratio 4.99 2.50 2.50 Evaluation Yes No No TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 57 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 10.3 Measured SAR Results Report No.: R1907A0375-S1V1 Table 10: GSM 850 Test Position Cover Type Channel Measured Tune-up power (dBm) (dBm) Limit of 10g SAR 2 W/kg (mW/g) Plot Power Measured Measured Scaling Report No. Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR Right Cheek Standard 128 33.5 33.13 0.09 0.015 0.012 1.09 0.016 / Right Tilted Standard 128 33.5 33.13 0.04 0.008 0.006 1.09 0.009 / Left Cheek Standard 128 33.5 33.13 0.09 0.016 0.012 1.09 0.017 1 Left Tilted Standard 128 33.5 33.13 -0.08 0.009 0.007 1.09 0.010 / Body-worn SAR (Distance 10mm) Front Face Standard 128 33.5 33.13 -0.07 0.131 0.096 1.09 0.143 / Rear Face Standard 128 33.5 33.13 -0.09 0.261 0.193 1.09 0.284 23 Hotspot SAR (Distance 10mm) Front Face(4Txslots) Standard 128 28.5 27.37 -0.08 0.127 0.093 1.30 0.165 / Rear Face(4Txslots) Standard 128 28.5 27.37 -0.19 0.225 0.173 1.30 0.292 12 Left Side(4Txslots) Standard 128 28.5 27.37 -0.07 0.176 0.12 1.30 0.228 / Right Side(4Txslots) Standard 128 28.5 27.37 -0.06 0.207 0.106 1.30 0.269 / Top Side (4Txslots) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side (4Txslots) Standard 128 28.5 27.37 -0.05 0.054 0.032 1.30 0.070 / Rear Face(4Txslots) SIM2 128 28.5 27.37 0.01 0.222 0.165 1.30 0.288 / Note: 1.The value with blue color is the maximum SAR Value of each test band. 2.When multiple slots are used, SAR should be tested to account for the maximum source-based time-averaged output power. 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 58 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 11: GSM 1900 Report No.: R1907A0375-S1V1 Test Position Cover Type Separation Measured Limit of 10g SAR 2 W/kg (mW/g) Tune-up Plot Distance Channel Sensor power (dBm) Power Measured Measured Scaling Report No. (cm) (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR Right Cheek Standard 0 661 / 30.5 30.08 -0.034 0.070 0.043 1.10 0.077 2 Right Tilted Standard 0 661 / 30.5 30.08 -0.030 0.028 0.017 1.10 0.031 / Left Cheek Standard 0 661 / 30.5 30.08 -0.141 0.042 0.028 1.10 0.046 / Left Tilted Standard 0 661 / 30.5 30.08 -0.024 0.044 0.027 1.10 0.049 / Body-worn SAR Front Face Standard 1 661 Off 30.5 30.08 -0.12 0.43 0.247 1.10 0.474 / Rear Face Standard 2 661 Off 30.5 30.08 0.01 0.443 0.261 1.10 0.488 / Rear Face Standard 1 512 On 25.5 25.16 0.03 0.709 0.374 1.08 0.767 24 Hotspot SAR Front Face(4Txslots) Standard 1 512 Off 25.5 24.61 0.01 0.395 0.23 1.23 0.485 / Rear Face(4Txslots) Standard 2 512 Off 25.5 24.61 0.11 0.406 0.243 1.23 0.498 / Left Side(4Txslots) Standard 1 512 Off 25.5 24.61 -0.19 0.052 0.036 1.23 0.064 / Right Side(4Txslots) Standard 1 512 Off 25.5 24.61 -0.01 0.06 0.038 1.23 0.074 / Top Side (4Txslots) N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side (4Txslots) Standard 1.7 512 Off 25.5 24.61 0.06 0.478 0.286 1.23 0.587 / Rear Face (4Txslots) Standard 1 512 On 21.5 20.66 0.03 0.664 0.327 1.21 0.806 13 Bottom Side (4Txslots) Standard 1 512 On 21.5 20.66 0.13 0.516 0.282 1.21 0.626 / Rear Face (4Txslots) Standard 1 661 On 21.5 20.41 0.03 0.607 0.331 1.29 0.780 / Rear Face (4Txslots) Standard 1 810 On 21.5 20.45 0.02 0.662 0.382 1.27 0.843 / Rear Face (4Txslots) SIM2 1 512 On 21.5 20.66 0.05 0.621 0.313 1.21 0.754 / Note: 1.The value with blue color is the maximum SAR Value of each test band. 2.When multiple slots are used, SAR should be tested to account for the maximum source-based time-averaged output power. 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 59 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 12: UMTS Band II (Main-antenna) Report No.: R1907A0375-S1V1 Test Position Cover Type Measured Limit of 10g SAR 2 W/kg (mW/g) Distance Tune-up Plot (cm) Channel Sensor power (dBm) Power Measured Measured Scaling Report No. (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR Right Cheek Standard 0 9538 / 24.5 23.32 -0.071 0.114 0.070 1.31 0.150 3 Right Tilted Standard 0 9538 / 24.5 23.32 -0.070 0.054 0.034 1.31 0.071 / Left Cheek Standard 0 9538 / 24.5 23.32 -0.173 0.063 0.042 1.31 0.083 / Left Tilted Standard 0 9538 / 24.5 23.32 -0.034 0.061 0.037 1.31 0.080 / Body-worn SAR Front Face Standard 1 9538 Off 24.5 23.32 -0.06 0.438 0.255 1.31 0.575 / Rear Face Standard 2 9538 Off 24.5 23.32 0.07 0.422 0.254 1.31 0.554 / Rear Face Standard 1 9538 On 17.5 16.42 0.01 0.456 0.238 1.28 0.585 25 Hotspot SAR Front Face Standard 1 9538 Off 24.5 23.32 -0.06 0.438 0.255 1.31 0.575 / Rear Face Standard 2 9538 Off 24.5 23.32 0.07 0.422 0.254 1.31 0.554 / Left Side Standard 1 9538 Off 24.5 23.32 -0.06 0.075 0.051 1.31 0.098 / Right Side Standard 1 9538 Off 24.5 23.32 0.08 0.092 0.056 1.31 0.121 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 9538 Off 24.5 23.32 0.00 0.544 0.371 1.31 0.714 / Rear Face Standard 1 9538 On 17.5 16.42 0.01 0.456 0.238 1.28 0.585 / Bottom Side Standard 1 9538 On 17.5 16.42 0.09 0.366 0.198 1.28 0.469 / Bottom Side SIM2 1.7 9538 Off 24.5 23.32 0.00 0.600 0.429 1.31 0.787 14 Note: 1.The value with blue color is the maximum SAR Value of each test band. 2. When the maximum output power and tune-up tolerance specified for production units in a secondary mode is ¼ dB higher than the primary mode or when the highest reported SAR of the primary mode is scaled by the ratio of specified maximum output power and tune-up tolerance of secondary to primary mode and the adjusted SAR is 1.2 W/kg, SAR measurement is not required for the secondary mode. 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 60 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 13: UMTS Band IV Report No.: R1907A0375-S1V1 Test Position Cover Type Measured Limit of 10g SAR 2 W/kg (mW/g) Distance Tune-up Plot (cm) Channel Sensor power (dBm) Power Measured Measured Scaling Report No. (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR Right Cheek Standard 0 1513 / 24.0 23.43 0.07 0.099 0.063 1.14 0.112 4 Right Tilted Standard 0 1513 / 24.0 23.43 0.03 0.039 0.025 1.14 0.044 / Left Cheek Standard 0 1513 / 24.0 23.43 -0.14 0.045 0.030 1.14 0.051 / Left Tilted Standard 0 1513 / 24.0 23.43 0.04 0.047 0.030 1.14 0.053 / Body-worn SAR Front Face Standard 1 1513 Off 24.0 23.43 0.08 0.624 0.356 1.14 0.712 / Rear Face Standard 2 1513 Off 24.0 23.43 0.14 0.583 0.358 1.14 0.665 / Rear Face Standard 1 1312 On 18.5 17.33 0.09 0.676 0.355 1.31 0.885 / Rear Face Standard 1 1413 On 18.5 17.14 -0.03 0.69 0.364 1.37 0.944 / Rear Face Standard 1 1513 On 18.5 17.16 -0.03 0.725 0.381 1.36 0.987 26 Hotspot SAR Front Face Standard 1 1513 Off 24.0 23.43 0.08 0.624 0.356 1.14 0.712 / Rear Face Standard 2 1513 Off 24.0 23.43 0.14 0.583 0.358 1.14 0.665 / Left Side Standard 1 1513 Off 24.0 23.43 0.13 0.073 0.05 1.14 0.083 / Right Side Standard 1 1513 Off 24.0 23.43 -0.03 0.128 0.079 1.14 0.146 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 1513 Off 24.0 23.43 0.19 1.000 0.611 1.14 1.140 15 Rear Face Standard 1 1312 On 18.5 17.33 0.09 0.676 0.355 1.31 0.885 / Bottom Side Standard 1 1312 On 18.5 17.33 0.01 0.506 0.274 1.31 0.662 / Bottom Side Standard 1.7 1312 Off 24.0 23.31 0.07 0.816 0.495 1.17 0.957 / Bottom Side Standard 1.7 1413 Off 24.0 23.26 0.07 0.939 0.568 1.19 1.113 / Rear Face Standard 1 1413 On 18.5 17.14 -0.03 0.69 0.364 1.37 0.944 / Rear Face Standard 1 1513 On 18.5 17.16 -0.03 0.725 0.381 1.36 0.987 / Bottom Side SIM2 1.7 1513 Off 24.0 23.43 0.01 0.963 0.589 1.14 1.098 / Bottom Side Repeated 1.7 1513 Off 24.0 23.43 0.03 0.996 0.601 1.14 1.136 / Note: 1.The value with blue color is the maximum SAR Value of each test band. 2. When the maximum output power and tune-up tolerance specified for production units in a secondary mode is ¼ dB higher than the primary mode or when the highest reported SAR of the primary mode is scaled by the ratio of specified maximum output power and tune-up tolerance of secondary to primary mode and the adjusted SAR is 1.2 W/kg, SAR measurement is not required for the secondary mode. 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 61 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Test Position Channel/ Frequency Measurement Variability MAX Measured SAR1g (W/kg) 1st Repeated SAR1g (W/kg) Ratio Bottom Side 1513 1.000 0.996 1.004 Note: 1) A second repeated measurement was preformed only if the ratio of largest to smallest SAR for the original and first repeated measurements was > 1.20 or when the original or repeated measurement was 1.45 W/kg (~ 10% from the 1-g SAR limit). 2) A third repeated measurement was performed only if the original, first or second repeated measurement was 1.5 W/kg and the ratio of largest to smallest SAR for the original, first and second repeated measurements is > 1.20. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 62 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 14: UMTS Band V Report No.: R1907A0375-S1V1 Test Position Cover Type Distance (cm) Channel Tune-up (dBm) Measured Limit of 10g SAR 2 W/kg (mW/g) Plot power Power Measured Measured Scaling Report No. (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR Right Cheek Standard 0 4233 24.5 23.04 0.02 0.105 0.08 1.40 0.147 / Right Tilted Standard 0 4233 24.5 23.04 0.05 0.053 0.04 1.40 0.074 / Left Cheek Standard 0 4233 24.5 23.04 0.05 0.115 0.087 1.40 0.161 5 Left Tilted Standard 0 4233 24.5 23.04 -0.01 0.063 0.049 1.40 0.088 / Body-worn SAR Front Face Standard 1 4233 24.5 23.04 -0.07 0.095 0.072 1.40 0.133 / Rear Face Standard 1 4233 24.5 23.04 0.05 0.148 0.088 1.40 0.207 / Rear Face SIM2 1 4233 24.5 23.04 -0.17 0.159 0.091 1.40 0.223 / Hotspot SAR Front Face Standard 1 4233 24.5 23.04 -0.07 0.095 0.072 1.40 0.133 / Rear Face Standard 1 4233 24.5 23.04 0.05 0.148 0.088 1.40 0.207 / Left Side Standard 1 4233 24.5 23.04 -0.14 0.107 0.074 1.40 0.150 / Right Side Standard 1 4233 24.5 23.04 -0.08 0.105 0.072 1.40 0.147 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1 4233 24.5 23.04 0.09 0.051 0.032 1.40 0.071 / Rear Face SIM2 1 4233 24.5 23.04 -0.18 0.149 0.086 1.40 0.209 16 Note: 1.The value with blue color is the maximum SAR Value of each test band. 2. When the maximum output power and tune-up tolerance specified for production units in a secondary mode is ¼ dB higher than the primary mode or when the highest reported SAR of the primary mode is scaled by the ratio of specified maximum output power and tune-up tolerance of secondary to primary mode and the adjusted SAR is 1.2 W/kg, SAR measurement is not required for the secondary mode. 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 63 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Table 15: LTE Band 2 Test Position Tune- Measured Limit of 10g SAR 2 W/kg (mW/g) Cover Distance RB Plot Type Channel Sensor RB up (cm) offset power Power Measured Measured Scaling Report No. (dBm) (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR (QPSK) Right Cheek Standard 0 18900 / 1 50 24.0 23.50 0.13 0.114 0.071 1.12 0.128 6 Right Tilted Standard 0 18900 / 1 50 24.0 23.50 -0.12 0.049 0.030 1.12 0.055 / Left Cheek Standard 0 18900 / 1 50 24.0 23.50 -0.18 0.056 0.037 1.12 0.063 / Left Tilted Standard 0 18900 / 1 50 24.0 23.50 0.04 0.052 0.032 1.12 0.058 / Right Cheek Standard 0 19100 / 50 50 23.0 22.46 0.09 0.095 0.059 1.13 0.107 / Right Tilted Standard 0 19100 / 50 50 23.0 22.46 0.03 0.043 0.027 1.13 0.048 / Left Cheek Standard 0 19100 / 50 50 23.0 22.46 -0.04 0.049 0.032 1.13 0.055 / Left Tilted Standard 0 19100 / 50 50 23.0 22.46 0.03 0.049 0.030 1.13 0.055 / Body-worn SAR Front Face Standard 1 18900 Off 1 50 24.0 23.50 0.06 0.546 0.316 1.12 0.613 / Rear Face Standard 2 18900 Off 1 50 24.0 23.50 0.07 0.638 0.384 1.12 0.716 / Front Face Standard 1 19100 Off 50 50 23.0 22.46 -0.07 0.348 0.203 1.13 0.394 / Rear Face Standard 2 19100 Off 50 50 23.0 22.46 0.12 0.417 0.252 1.13 0.472 / Rear Face Standard 1 18700 On 1 50 18.0 17.43 0.18 0.787 0.417 1.14 0.897 / Rear Face Standard 1 18700 On 50 50 18.0 17.30 -0.08 0.762 0.402 1.17 0.895 / Rear Face Standard 1 18700 On 100 0 18.0 17.19 0.01 0.735 0.388 1.21 0.886 / Rear Face Standard 1 18900 On 1 50 18.0 17.24 0.18 0.805 0.427 1.19 0.959 / Rear Face Standard 1 19100 On 1 50 18.0 16.84 0.12 0.822 0.436 1.31 1.074 27 Rear Face Standard 1 18900 On 50 25 18.0 17.21 -0.04 0.780 0.411 1.20 0.936 / Rear Face Standard 1 19100 On 50 0 18.0 17.21 -0.02 0.796 0.42 1.20 0.955 / Hotspot SAR Front Face Standard 1 18900 Off 1 50 24.0 23.50 0.06 0.546 0.316 1.12 0.613 / Rear Face Standard 2 18900 Off 1 50 24.0 23.50 0.07 0.638 0.384 1.12 0.716 / Left Side Standard 1 18900 Off 1 50 24.0 23.50 -0.14 0.027 0.017 1.12 0.030 / Right Side Standard 1 18900 Off 1 50 24.0 23.50 -0.03 0.093 0.058 1.12 0.104 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 18900 Off 1 50 24.0 23.50 0.08 0.875 0.522 1.12 0.982 17 Front Face Standard 1 19100 Off 50 50 23.0 22.46 -0.07 0.348 0.203 1.13 0.394 / Rear Face Standard 2 19100 Off 50 50 23.0 22.46 0.12 0.417 0.252 1.13 0.472 / Left Side Standard 1 19100 Off 50 50 23.0 22.46 0.01 0.023 0.014 1.13 0.026 / Right Side Standard 1 19100 Off 50 50 23.0 22.46 0.05 0.088 0.052 1.13 0.100 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 19100 Off 50 50 23.0 22.46 -0.06 0.548 0.329 1.13 0.621 / Rear Face Standard 1 18700 On 1 50 18.0 17.43 0.18 0.787 0.417 1.14 0.897 / TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 64 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Bottom Side Standard 1 18700 On 1 50 18.0 17.43 0.12 Report No.: R1907A0375-S1V1 0.605 0.336 1.14 0.690 / Rear Face Standard 1 18700 On 50 50 18.0 17.30 -0.08 0.762 0.402 1.17 0.895 / Bottom Side Standard 1 18700 On 50 50 18.0 17.30 0.05 0.593 0.329 1.17 0.697 / Bottom Side Standard 1.7 19100 Off 100 0 23.0 22.39 0.03 0.544 0.323 1.15 0.626 / Rear Face Standard 1 18700 On 100 0 18.0 17.19 0.01 0.735 0.388 1.21 0.886 / Bottom Side Standard 1.7 18700 Off 1 50 24.0 23.47 0.02 0.630 0.405 1.13 0.712 / Bottom Side Standard 1.7 19100 Off 1 50 24.0 23.31 -0.19 0.620 0.397 1.17 0.727 / Rear Face Standard 1 18900 On 1 50 18.0 17.24 0.18 0.805 0.427 1.19 0.959 / Rear Face Standard 1 19100 On 1 50 18.0 16.84 0.12 0.822 0.436 1.31 1.074 / Rear Face Standard 1 18900 On 50 25 18.0 17.21 -0.04 0.780 0.411 1.20 0.936 / Rear Face Standard 1 19100 On 50 0 18.0 17.21 -0.02 0.796 0.420 1.20 0.955 / Bottom Side SIM2 1.7 18900 Off 1 50 24.0 23.50 0.03 0.798 0.415 1.12 0.895 / Bottom Side Repeated 1.7 18900 Off 1 50 24.0 23.50 0.04 0.822 0.491 1.12 0.922 / Note: 1.The value with blue color is the maximum SAR Value of each test band. 2.For QPSK with 100% RB allocation, SAR is required when and the highest reported SAR for 1 RB and 50% RB allocation in are 50% limit(1g). 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. Test Position Channe Measurement Variability MAX Measured SAR1g (W/kg) 1st Repeated SAR1g (W/kg) Ratio Bottom Side 18900 0.827 0.822 1.006 Note: 1) A second repeated measurement was preformed only if the ratio of largest to smallest SAR for the original and first repeated measurements was > 1.20 or when the original or repeated measurement was 1.45 W/kg (~ 10% from the 1-g SAR limit). 2) A third repeated measurement was performed only if the original, first or second repeated measurement was 1.5 W/kg and the ratio of largest to smallest SAR for the original, first and second repeated measurements is > 1.20. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 65 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 16: LTE Band 4 (20MHz, Main-antenna) Report No.: R1907A0375-S1V1 Test Position Tune- Measured Limit of 10g SAR 2 W/kg (mW/g) Cover Distance RB Plot Type Channel Sensor RB up (cm) offset power Power Measured Measured Scaling Report No. (dBm) (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR (QPSK) Right Cheek Standard 0 20300 / 1 50 24.0 23.07 0.10 0.114 0.074 1.24 0.141 7 Right Tilted Standard 0 20300 / 1 50 24.0 23.07 0.04 0.043 0.028 1.24 0.053 / Left Cheek Standard 0 20300 / 1 50 24.0 23.07 0.11 0.045 0.030 1.24 0.055 / Left Tilted Standard 0 20300 / 1 50 24.0 23.07 0.09 0.049 0.032 1.24 0.061 / Right Cheek Standard 0 20300 / 50 50 23.0 21.94 0.14 0.087 0.056 1.28 0.111 / Right Tilted Standard 0 20300 / 50 50 23.0 21.94 0.04 0.034 0.022 1.28 0.044 / Left Cheek Standard 0 20300 / 50 50 23.0 21.94 0.05 0.043 0.028 1.28 0.054 / Left Tilted Standard 0 20300 / 50 50 23.0 21.94 0.02 0.042 0.026 1.28 0.054 / Body-worn SAR Front Face Standard 1 20300 Off 1 50 24.0 23.07 -0.03 0.550 0.324 1.24 0.681 / Rear Face Standard 2 20300 Off 1 50 24.0 23.07 -0.16 0.618 0.381 1.24 0.766 / Front Face Standard 1 20300 Off 50 50 23.0 21.94 -0.03 0.560 0.328 1.28 0.715 / Rear Face Standard 2 20300 Off 50 50 23.0 21.94 -0.14 0.617 0.380 1.28 0.788 / Rear Face Standard 1 20300 On 1 50 18.0 17.03 0.02 0.626 0.363 1.25 0.783 / Rear Face Standard 1 20300 On 50 50 18.0 16.97 0.03 0.624 0.366 1.27 0.791 28 Hotspot SAR Front Face Standard 1 20300 Off 1 50 24.0 23.07 -0.03 0.550 0.324 1.24 0.681 / Rear Face Standard 2 20300 Off 1 50 24.0 23.07 -0.16 0.618 0.381 1.24 0.766 / Left Side Standard 1 20300 Off 1 50 24.0 23.07 0.12 0.062 0.044 1.24 0.077 / Right Side Standard 1 20300 Off 1 50 24.0 23.07 -0.15 0.107 0.069 1.24 0.133 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 20300 Off 1 50 24.0 23.07 -0.03 0.787 0.485 1.24 0.975 / Front Face Standard 1 20300 Off 50 50 23.0 21.94 -0.03 0.56 0.328 1.28 0.715 / Rear Face Standard 2 20300 Off 50 50 23.0 21.94 -0.14 0.617 0.380 1.28 0.788 / Left Side Standard 1 20300 Off 50 50 23.0 21.94 0.03 0.054 0.040 1.28 0.069 / Right Side Standard 1 20300 Off 50 50 23.0 21.94 0.03 0.101 0.066 1.28 0.129 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 20300 Off 50 50 23.0 21.94 0.07 0.855 0.426 1.28 1.091 18 Rear Face Standard 1 20300 On 1 50 18.0 17.03 0.02 0.626 0.363 1.25 0.783 / Bottom Side Standard 1 20300 On 1 50 18.0 17.03 0.08 0.518 0.290 1.25 0.648 / Rear Face Standard 1 20300 On 50 50 18.0 16.97 0.03 0.624 0.366 1.27 0.791 / Bottom Side Standard 1 20300 On 50 50 18.0 16.97 0.08 0.525 0.293 1.27 0.666 / Bottom Side Standard 1.7 20300 Off 100 0 23.0 21.87 -0.11 0.812 0.499 1.30 1.053 / Bottom Side Standard 1.7 20050 Off 1 50 24.0 22.86 -0.04 0.765 0.472 1.30 0.995 / Bottom Side Standard 1.7 20175 Off 1 99 24.0 22.69 0.05 0.775 0.478 1.35 1.048 / TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 66 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Bottom Side Standard 1.7 20050 Off 50 50 23.0 21.74 -0.04 Report No.: R1907A0375-S1V1 0.709 0.432 1.34 0.948 / Bottom Side Standard 1.7 20175 Off 50 50 23.0 21.77 -0.06 0.756 0.462 1.33 1.004 / Bottom Side SIM2 1.7 20300 Off 50 50 23.0 21.94 0.05 0.785 0.466 1.28 1.002 / Bottom Side Repeated 1.7 20300 Off 50 50 23.0 21.94 0.12 0.821 0.500 1.28 1.048 / Note: 1.The value with blue color is the maximum SAR Value of each test band. 2.For QPSK with 100% RB allocation, SAR is required when and the highest reported SAR for 1 RB and 50% RB allocation in are 50% limit(1g). 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. Test Position Channe Measurement Variability MAX Measured SAR1g (W/kg) 1st Repeated SAR1g (W/kg) Ratio Bottom Side 20300 0.823 0.821 1.002 Note: 1) A second repeated measurement was preformed only if the ratio of largest to smallest SAR for the original and first repeated measurements was > 1.20 or when the original or repeated measurement was 1.45 W/kg (~ 10% from the 1-g SAR limit). 2) A third repeated measurement was performed only if the original, first or second repeated measurement was 1.5 W/kg and the ratio of largest to smallest SAR for the original, first and second repeated measurements is > 1.20. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 67 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 17: LTE Band 5 Report No.: R1907A0375-S1V1 Test Cover Distance Channel RB Position Type (cm) RB offset Tune- Measured Limit of 10g SAR 2 W/kg (mW/g) Plot up power Power Measured Measured Scaling Report No. (dBm) (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR (QPSK) Right Cheek Standard 0 20600 1 24 24.0 23.22 -0.12 0.142 0.106 1.20 0.170 / Right Tilted Standard 0 20600 1 24 24.0 23.22 -0.17 0.071 0.054 1.20 0.085 / Left Cheek Standard 0 20600 1 24 24.0 23.22 0.08 0.149 0.114 1.20 0.178 8 Left Tilted Standard 0 20600 1 24 24.0 23.22 0.05 0.071 0.054 1.20 0.085 / Right Cheek Standard 0 20600 25 0 23.0 22.10 0.02 0.106 0.080 1.23 0.130 / Right Tilted Standard 0 20600 25 0 23.0 22.10 -0.07 0.054 0.041 1.23 0.066 / Left Cheek Standard 0 20600 25 0 23.0 22.10 0.15 0.116 0.086 1.23 0.143 / Left Tilted Standard 0 20600 25 0 23.0 22.10 0.12 0.054 0.041 1.23 0.066 / Body-worn SAR Front Face Standard 1 20600 1 24 24.0 23.22 -0.03 0.067 0.051 1.20 0.080 / Rear Face Standard 1 20600 1 24 24.0 23.22 -0.03 0.116 0.087 1.20 0.139 29 Front Face Standard 1 20600 25 0 23.0 22.10 -0.18 0.056 0.043 1.23 0.069 / Rear Face Standard 1 20600 25 0 23.0 22.10 -0.15 0.096 0.073 1.23 0.118 / Hotspot SAR Front Face Standard 1 20600 1 24 24.0 23.22 -0.03 0.067 0.051 1.20 0.080 / Rear Face Standard 1 20600 1 24 24.0 23.22 -0.03 0.116 0.087 1.20 0.139 / Left Side Standard 1 20600 1 24 24.0 23.22 -0.06 0.072 0.049 1.20 0.086 / Right Side Standard 1 20600 1 24 24.0 23.22 -0.13 0.117 0.072 1.20 0.140 19 Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1 20600 1 24 24.0 23.22 -0.12 0.047 0.029 1.20 0.056 / Front Face Standard 1 20600 25 0 23.0 22.10 -0.18 0.056 0.043 1.23 0.069 / Rear Face Standard 1 20600 25 0 23.0 22.10 -0.15 0.096 0.073 1.23 0.118 / Left Side Standard 1 20600 25 0 23.0 22.10 -0.13 0.06 0.041 1.23 0.074 / Right Side Standard 1 20600 25 0 23.0 22.10 -0.15 0.1 0.068 1.23 0.123 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1 20600 25 0 23.0 22.10 -0.08 0.046 0.029 1.23 0.057 / Right Side SIM2 1 20600 1 24 24.0 23.22 0.03 0.111 0.071 1.20 0.133 / Note: 1.The value with blue color is the maximum SAR Value of each test band. 2.For QPSK with 100% RB allocation, SAR is required when and the highest reported SAR for 1 RB and 50% RB allocation in are 50% limit(1g). 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 68 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 18: LTE Band 7 Report No.: R1907A0375-S1V1 Test Position Tune- Measured Limit of 10g SAR 2 W/kg (mW/g) Cover Distance RB Plot Type Channel Sensor RB up (cm) offset power Power Measured Measured Scaling Report No. (dBm) (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR (QPSK) Right Cheek Standard 0 20850 / 1 50 24.0 23.53 0.15 0.115 0.064 1.11 0.128 9 Right Tilted Standard 0 20850 / 1 50 24.0 23.53 0.03 0.03 0.016 1.11 0.033 / Left Cheek Standard 0 20850 / 1 50 24.0 23.53 -0.05 0.059 0.035 1.11 0.066 / Left Tilted Standard 0 20850 / 1 50 24.0 23.53 0.17 0.048 0.024 1.11 0.053 / Right Cheek Standard 0 21350 / 50 0 23.0 22.38 0.18 0.096 0.052 1.15 0.111 / Right Tilted Standard 0 21350 / 50 0 23.0 22.38 0.04 0.028 0.014 1.15 0.032 / Left Cheek Standard 0 21350 / 50 0 23.0 22.38 0.03 0.056 0.032 1.15 0.065 / Left Tilted Standard 0 21350 / 50 0 23.0 22.38 0.09 0.040 0.021 1.15 0.046 / Body-worn SAR Front Face Standard 1 20850 Off 1 50 24.0 23.53 0.15 0.327 0.174 1.11 0.364 / Rear Face Standard 2 20850 Off 1 50 24.0 23.53 0.03 0.670 0.326 1.11 0.747 / Front Face Standard 1 21350 Off 50 0 23.0 22.38 0.06 0.323 0.173 1.15 0.373 / Rear Face Standard 2 21350 Off 50 0 23.0 22.38 0.07 0.632 0.311 1.15 0.729 / Rear Face Standard 1 20850 On 1 50 18.0 17.61 0.16 0.377 0.164 1.09 0.412 / Rear Face Standard 1 20850 On 50 25 18.0 17.41 0.09 0.377 0.163 1.15 0.432 / Rear Face SIM 2 2 20850 Off 1 50 24.0 23.53 0.04 0.61 0.322 1.11 0.680 / Hotspot SAR Front Face Standard 1 20850 Off 1 50 24.0 23.53 0.15 0.327 0.174 1.11 0.364 / Rear Face Standard 2 20850 Off 1 50 24.0 23.53 0.03 0.670 0.326 1.11 0.747 20 Left Side Standard 1 20850 Off 1 50 24.0 23.53 0.04 0.066 0.04 1.11 0.074 / Right Side Standard 1 20850 Off 1 50 24.0 23.53 -0.03 0.219 0.128 1.11 0.244 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 20850 Off 1 50 24.0 23.53 -0.02 0.617 0.312 1.11 0.688 / Front Face Standard 1 21350 Off 50 0 23.0 22.38 0.06 0.323 0.173 1.15 0.373 / Rear Face Standard 2 21350 Off 50 0 23.0 22.38 0.07 0.632 0.311 1.15 0.729 / Left Side Standard 1 21350 Off 50 0 23.0 22.38 -0.18 0.067 0.041 1.15 0.077 / Right Side Standard 1 21350 Off 50 0 23.0 22.38 -0.17 0.184 0.107 1.15 0.212 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 21350 Off 50 0 23.0 22.38 -0.02 0.623 0.265 1.15 0.719 / Rear Face Standard 1 20850 On 1 50 18.0 17.61 0.16 0.377 0.164 1.09 0.412 / Bottom Side Standard 1 20850 On 1 50 18.0 17.61 -0.03 0.324 0.146 1.09 0.354 / Rear Face Standard 1 20850 On 50 25 18.0 17.41 0.09 0.377 0.163 1.15 0.432 / Bottom Side Standard 1 20850 On 50 25 18.0 17.41 -0.04 0.321 0.145 1.15 0.368 / Rear Face SIM2 2 20850 Off 1 50 24.0 23.53 0.04 0.610 0.322 1.11 0.680 / TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 69 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Note: 1.The value with blue color is the maximum SAR Value of each test band. 2.For QPSK with 100% RB allocation, SAR is required when and the highest reported SAR for 1 RB and 50% RB allocation in are 50% limit(1g). 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 70 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 19: LTE Band 38 Report No.: R1907A0375-S1V1 Test Position Tune- Measured Limit of 10g SAR 2 W/kg (mW/g) Cover Distance RB Plot Type Channel Sensor RB up (cm) offset power Power Measured Measured Scaling Report No. (dBm) (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR (QPSK) Right Cheek Standard 0 38150 / 1 50 24.0 23.05 0.03 0.037 0.019 1.24 0.046 10 Right Tilted Standard 0 38150 / 1 50 24.0 23.05 0.03 0.032 0.017 1.24 0.040 / Left Cheek Standard 0 38150 / 1 50 24.0 23.05 0.03 0.012 0.004 1.24 0.015 / Left Tilted Standard 0 38150 / 1 50 24.0 23.05 0.14 0.022 0.011 1.24 0.027 / Right Cheek Standard 0 38150 / 50 50 23.0 21.71 0.04 0.031 0.016 1.35 0.042 / Right Tilted Standard 0 38150 / 50 50 23.0 21.71 0.05 0.029 0.013 1.35 0.039 / Left Cheek Standard 0 38150 / 50 50 23.0 21.71 0.02 0.011 0.003 1.35 0.015 / Left Tilted Standard 0 38150 / 50 50 23.0 21.71 0.11 0.019 0.009 1.35 0.026 / Body-worn SAR Front Face Standard 1 38150 Off 1 50 24.0 23.05 0.08 0.133 0.069 1.24 0.166 / Rear Face Standard 2 38150 Off 1 50 24.0 23.05 -0.07 0.144 0.079 1.24 0.179 / Front Face Standard 1 38150 Off 50 50 23.0 21.71 -0.05 0.113 0.058 1.35 0.152 / Rear Face Standard 2 38150 Off 50 50 23.0 21.71 0.05 0.129 0.071 1.35 0.174 / Rear Face Standard 1 38000 On 1 50 22.5 21.46 0.04 0.174 0.095 1.27 0.221 / Rear Face Standard 1 38150 On 50 0 22.5 21.23 0.16 0.17 0.093 1.34 0.228 / Rear Face SIM 2 1 38000 On 1 50 22.5 21.46 0.04 0.156 0.088 1.27 0.198 / Hotspot SAR Front Face Standard 1 38150 Off 1 50 24.0 23.05 0.08 0.133 0.069 1.24 0.166 / Rear Face Standard 2 38150 Off 1 50 24.0 23.05 -0.07 0.144 0.079 1.24 0.179 / Left Side Standard 1 38150 Off 1 50 24.0 23.05 0.01 0.044 0.025 1.24 0.055 / Right Side Standard 1 38150 Off 1 50 24.0 23.05 -0.07 0.083 0.047 1.24 0.103 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 38150 Off 1 50 24.0 23.05 0.04 0.119 0.063 1.24 0.148 / Front Face Standard 1 38150 Off 50 50 23.0 21.71 -0.05 0.113 0.058 1.35 0.152 / Rear Face Standard 2 38150 Off 50 50 23.0 21.71 0.05 0.129 0.071 1.35 0.174 / Left Side Standard 1 38150 Off 50 50 23.0 21.71 -0.18 0.036 0.021 1.35 0.048 / Right Side Standard 1 38150 Off 50 50 23.0 21.71 -0.01 0.070 0.039 1.35 0.094 / Top Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Bottom Side Standard 1.7 38150 Off 50 50 23.0 21.71 -0.06 0.099 0.053 1.35 0.133 / Rear Face Standard 1 38000 On 1 50 22.5 21.46 -0.08 0.247 0.148 1.27 0.314 21 Bottom Side Standard 1 38000 On 1 50 22.5 21.46 -0.03 0.147 0.072 1.27 0.187 / Rear Face Standard 1 38150 On 50 0 22.5 21.23 0.16 0.170 0.093 1.34 0.228 / Bottom Side Standard 1 38150 On 50 0 22.5 21.23 -0.04 0.149 0.073 1.34 0.200 / Rear Face SIM 2 1 38000 On 1 50 22.5 21.46 0.04 0.156 0.088 1.27 0.198 / TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 71 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Note: 1.The value with blue color is the maximum SAR Value of each test band. 2.For QPSK with 100% RB allocation, SAR is required when and the highest reported SAR for 1 RB and 50% RB allocation in are 50% limit(1g). 3. Accessories that do not contain RF transmitters and have been proven to increase the peak SAR by less than 5 %, such as hands-free kits, do not need SAR tests separate from the SAR tests attached to a main EUT configuration. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 72 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Table 20: Wi-Fi (2.4G) Report No.: R1907A0375-S1V1 Test Position Cover Type Mode 802. 11b Duty Cycle Measured Limit of SAR 1.6 W/kg (mW/g) Tune-up Plot Channel dBm) power Power Measured Measured Scaling Report No. (dBm) Drift(dB) SAR1g SAR10g Factor SAR1g Head SAR Right Cheek standard DSSS 1:1 11 17.5 16.84 0.03 0.27 0.141 1.16 0.314 / Right Tilted standard DSSS 1:1 11 17.5 16.84 -0.05 0.253 0.218 1.16 0.295 / Left Cheek standard DSSS 1:1 11 17.5 16.84 0.06 0.392 0.204 1.16 0.456 / Left Tilted standard DSSS 1:1 11 17.5 16.84 0.05 0.411 0.191 1.16 0.478 11 Body-worn SAR (Distance 10mm) Front Face standard DSSS 1:1 11 17.5 16.84 -0.01 0.063 0.035 1.16 0.073 / Rear Face standard DSSS 1:1 11 17.5 16.84 0.01 0.188 0.087 1.16 0.219 30 Right Side standard DSSS 1:1 11 17.5 16.84 -0.01 0.05 0.027 1.16 0.058 / Rear Face standard DSSS 1:1 11 17.5 16.84 0.08 0.131 0.061 1.16 0.153 / Hotspot SAR(Distance 10mm) Front Face standard DSSS 1:1 11 17.5 16.84 -0.01 0.063 0.035 1.16 0.073 / Rear Face standard DSSS 1:1 11 17.5 16.84 0.01 0.188 0.087 1.16 0.219 22 Left Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Right Side standard DSSS 1:1 11 17.5 16.84 -0.01 0.05 0.027 1.16 0.058 / Top Side standard DSSS 1:1 11 17.5 16.84 0.08 0.131 0.061 1.16 0.153 / Bottom Side N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Note: 1. The value with blue color is the maximum SAR Value of each test band. MAX Adjusted SAR Mode Test Position Channel/ Frequency (MHz) MAX Reported SAR1g (W/kg) 802.11b Tune-up limit (dBm) Tune-up limit (dBm) Scaling Factor Adjusted SAR1g (W/kg) 802.11g Left Tilted 11 0.478 17.5 16 0.71 0.338 802.11n HT20 Left Tilted 11 0.478 17.5 14 0.45 0.214 Note: SAR is not required for OFDM when the highest reported SAR for DSSS is adjusted by the ratio of OFDM to DSSS specified maximum output power and the adjusted SAR is 1.2 W/kg. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 73 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Table 21: BT Test Position Cover Type Channel/ Measured Limit of 10g SAR 2 W/kg (mW/g) Duty Tune-up Plot Frequency Cycle (dBm) power Measured Power Scaling Report No. (MHz) (dBm) SAR1g Drift (dB) Factor SAR 1g Body SAR (Distance 5mm) Right Cheek Standard 77.0% 39/2441 10.00 8.91 0.075 -0.090 1.67 0.126 / Right Tilted Standard 77.0% 39/2441 10.00 8.91 0.042 -0.110 1.67 0.070 / Left Cheek Standard 77.0% 39/2441 10.00 8.91 0.087 0.033 1.67 0.145 / Left Tilted Standard 77.0% 39/2441 10.00 8.91 0.106 0.080 1.67 0.177 31 Note: 1.The value with blue color is the maximum SAR Value of each test band. Band Configuration Frequency (MHz) Maximum Power (dBm) Separation Distance (mm) Estimated SAR (W/kg) Body-worn 2480 12 Bluetooth Hotspot SAR 2480 12 10 0.333 10 0.333 For simultaneous transmission analysis, Bluetooth SAR is estimated per KDB 447498 D01 based on the formula below. (max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]·[f(GHz)/x] W/kg for test separation distances 50 mm; where x = 7.5 for 1-g SAR, and x = 18.75 for 10-g SAR. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 74 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 10.4 Simultaneous Transmission Analysis Report No.: R1907A0375-S1V1 Simultaneous Transmission Configurations Head Body-worn Hotspot GSM Voice + BT N/A Yes Yes GSM DATA + BT N/A Yes Yes GSM Voice + Wi-Fi Yes Yes Yes GSM DATA + Wi-Fi N/A Yes Yes WCDMA Voice + BT N/A Yes Yes WCDMA Data + BT N/A Yes Yes WCDMA Voice + Wi-Fi Yes Yes Yes WCDMA Data + Wi-Fi N/A Yes Yes LTE Data + Wi-Fi Yes Yes Yes LTE Data + BT N/A Yes Yes BT+ Wi-Fi N/A N/A N/A General Note: 1. The Scaled SAR summation is calculated based on the same configuration and test position. 2. Per KDB 447498 D01, simultaneous transmission SAR is compliant if, i) Scalar SAR summation < 1.6W/kg, simultaneously transmission SAR measurement is not necessary. ii) SPLSR = (SAR1 + SAR2)^1.5 / (min. separation distance, mm), and the peak separation distance is determined from the square root of [(x1-x2)2 + (y1-y2)2 + (z1-z2)2], where (x1, y1, z1) and (x2, y2, z2) are the coordinates of the extrapolated peak SAR locations in the zoom scan. iii) If SPLSR 0.04, simultaneously transmission SAR measurement is not necessary. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 75 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report The maximum SAR1g Value for Main-Antenna SAR1g(W/kg) GSM GSM WCDMA WCDMA WCDMA Test Position 850 1900 Band II Band IV Band V Right Cheek 0.016 0.077 0.150 0.112 0.147 Right Tilted 0.009 0.031 0.071 0.044 0.074 Left Cheek 0.017 0.046 0.083 0.051 0.161 Left Tilted 0.010 0.049 0.080 0.053 0.088 Body- Front Face 0.143 0.474 0.575 0.712 0.133 worn Rear Face 0.284 0.767 0.585 0.987 0.223 Front Face 0.165 0.485 0.575 0.712 0.133 Rear Face 0.292 0.843 0.585 0.987 0.209 Hotspot Left Side Right Side 0.228 0.064 0.269 0.074 0.098 0.121 0.083 0.146 0.150 0.147 Top Side N/A N/A N/A N/A N/A Bottom Side 0.070 0.626 0.787 1.140 0.071 LTE FDD 2 0.128 0.055 0.063 0.058 0.613 1.074 0.613 1.074 0.030 0.104 N/A 0.928 Report No.: R1907A0375-S1V1 LTE FDD 4 0.141 0.053 0.055 0.061 0.715 0.791 0.715 0.791 0.077 0.133 N/A 1.091 LTE FDD 5 0.170 0.085 0.178 0.085 0.080 0.139 0.080 0.139 0.086 0.140 N/A 0.057 LTE FDD 7 0.128 0.033 0.066 0.053 0.373 0.747 0.373 0.747 0.077 0.244 N/A 0.719 LTE FDD 38 0.046 MAX. SAR1g 0.170 0.040 0.085 0.015 0.178 0.027 0.088 0.166 0.715 0.228 1.074 0.166 0.715 0.314 1.074 0.055 0.228 0.103 0.269 N/A 0.000 0.200 1.140 About BT and Main- Antenna SAR1g (W/kg) Test Position Right Cheek Main-antenna 0.170 BT 0.126 MAX. SAR1g 0.296 Right Tilted 0.085 0.070 0.155 Left Cheek 0.178 0.145 0.323 Left Tilted 0.088 0.177 0.265 Body worn Front Face Rear Face 0.715 1.074 0.333 0.333 1.048 1.407 Front Face 0.715 0.333 1.048 Rear Face 1.074 0.333 1.407 Hotspot Left Side Right Side 0.228 0.269 0.333 0.333 0.561 0.602 Top Side 0.000 0.333 0.333 Bottom Side 1.140 0.333 1.473 Note: 1.The value with blue color is the maximum SAR1g Value. 2.MAX. SAR1g =Unlicensed SARMAX +Licensed SARMAX MAX. SAR1g =1.473W/kg<1.6W/kg, so the Simultaneous transimition SAR with volum scan are not required for BT and Main-Antenna. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 76 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 About Wi-Fi and Main-Antenna SAR1g (W/kg) Test Position Right Cheek Main-antenna 0.170 Wi-Fi 0.314 MAX. SAR1g 0.484 Right Tilted 0.085 0.295 0.380 Left Cheek 0.178 0.456 0.634 Left Tilted 0.088 0.478 0.566 Body worn Front Face Rear Face 0.715 1.074 0.073 0.219 0.788 1.293 Front Face 0.715 0.073 0.788 Rear Face 1.074 0.219 1.293 Hotspot Left Side Right Side 0.228 0.269 0 0.058 0.228 0.327 Top Side 0.000 0.153 0.153 Bottom Side 1.140 0 1.140 Note: 1.The value with blue color is the maximum SAR1g Value. 2.MAX. SAR1g =Unlicensed SARMAX +Licensed SARMAX MAX. SAR1g =1.293W/kg<1.6W/kg, so the Simultaneous transimition SAR with volum scan are not required for Wi-Fi and Main-Antenna. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 77 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report 11 Measurement Uncertainty Report No.: R1907A0375-S1V1 Per KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz, when the highest measured 1-g SAR within a frequency band is < 1.5 W/kg, the extensive SAR measurement uncertainty analysis described in IEEE Std 1528- 2013 is not required in SAR reports submitted for equipment approval. TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 78 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report ANNEX A: Test Layout Report No.: R1907A0375-S1V1 TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 79 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 Tissue Simulating Liquids For the measurement of the field distribution inside the flat phantom with DASY, the phantom must be filled with around 25 liters of homogeneous body tissue simulating liquid. For Head and Body SAR testing, the liquid height from the center of the flat phantom to the liquid top surface is larger than 15 cm, which is shown in Picture 3 and Picture 4. Picture 3: liquid depth in the head Phantom Picture 4: Liquid depth in the flat Phantom TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 80 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd. FCC SAR Test Report Report No.: R1907A0375-S1V1 ANNEX B:The EUT Appearances and Test Configuration ANNEX C: System Check Results ANNEX D: Highest Graph Results ANNEX E: Calibration Certificate TA Technology (Shanghai) Co., Ltd. TA-MB-05-003S Page 81 of 81 This report shall not be reproduced except in full, without the written approval of TA Technology (Shanghai) Co., Ltd.Acrobat Distiller 9.0.0 (Windows)